Search Documents

By P. A. Riveros

This paper describes the leaching of the common copper minerals tennantite (Cu12As4S13), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4) in acidic media using Fe(SO4)1.5, FeC13 or 02 as oxidizing agents. At temperatures <100°C, tennantite dissolves slowly in Fe(SO4)1.5-H2SO4 media, and the rate is directly proportional to the area of the sized tennantite. The rate increases sharply with increasing temperature and the apparent activation energy is 69 kJ/mol. Increasing Fe(SO4)1.5 concentrations slightly increase the tennantite leaching rate. The kinetics of dissolution of disks of synthetic iron-bearing tetrahedrite in Fe(SO4)1.5-H2SO4 media are linear; the leaching rates are slow but increase significantly with increasing temperature, with an apparent activation energy of 120 kJ/mol. The dissolution of sized particles of natural Ag-bearing tetrahedrite in FeC13- HC1 solutions proceeds according to the shrinking core model, and both Cu and Ag dissolve at about the same rate, provided that the total chloride concentration of the solution is sufficiently high to solubilize the AgC1 reaction product. The leaching rates are slow, and the apparent activation energy is 116 kJ/mol. The addition of sulphate ions to the FeC13-HC1 system reduces the tetrahedrite leaching rate to values similar to those realized in the Fe(SO4)1.5-H2SO4 system. At <100°C, enargite dissolves slowly in either Fe(SO4)1.5 or FeC13 media, and the dissolution rate obeys the shrinking core model. The rate increases with increasing temperature and the apparent activation energies are 50-64 kJ/mol. The rate increases slightly with increasing FeC13 concentrations in 0.3 M HC1 media. The leaching of enargite at elevated temperatures and pressures was also investigated. Potentially useful leaching rates are achieved above 170°C, at which temperature sulphate, rather than sulphur, is produced. Lower temperatures (130-160°C) lead to fast initial leaching rates, but the dissolution of the enargite is incomplete because of the coating of the enargite particles by elemental sulphur.

Jan 1, 2007

By A. Perucho, J. P. Harrison, A. Bedi, L. Alejano, L. Lamas, A. Sofianos, A. M. Ferrero, R. Migliazza, R. Olsson, J-F. Mathier

"In 2010, the Eurocode for Geotechnical Design, EN-1997-1:2004 (CEN, 2004), informally known as Eurocode 7 or EC7, became the Reference Design Code (RDC) for geotechnical design – including rock engineering design – within the European Union (EU). EC7 is one standard within the comprehensive Structural Eurocode suite, which as a whole has been also adopted by a number of other countries beyond the EU. EC7 is thus becoming a key design standard for geotechnical engineering worldwide.As part of the Structural Eurocode suite, EC7 requires designs to adhere to the principles of Limit State Design. However, it is not clear that current rock engineering design practice can satisfy this requirement. In addition, evidence is accumulating that EC7 is currently difficult to apply to, and may even be inappropriate for, rock engineering design. These issues may be due to the fact that the development of EC7 to date took place without any formal input from the international rock mechanics and rock engineering community.In early 2011 under the auspices of CEN (Comité Européen de Normalisation / European Committee for Standardisation), EC7 entered a formal period of maintenance which was aimed at improving the applicability and ease-of-use of the Code. This maintenance cycle will conclude in 2020 with the publication of a revised version of EC7.This paper describes a number of critical aspects for rock engineering in the context of EC7, inparticular the following:– the history of the Structural Eurocodes and the concepts they embody;– the nature of Limit State Design and the challenges and opportunities it poses for rock engineering design;– the formal means by which the Structural Eurocode maintenance cycle proceeds;– the plans currently being developed for improving EC7 with regard to rock engineering design and construction;– the unique and vital opportunity for the entire international rock mechanics and rock engineering community to comment on the Code and make suggestions for its improvement."

Jan 1, 2015

Deformation is a critical indicator required to evaluate the structural safety, stability, and integrity. For example, the deformed shape of a building structure is a key parameter that needs to be measured and tracked during laboratory testing or post-disaster inspections. However, existing techniques used for the deformation measurement and tracking do not have all the desirable characteristics, such as: reliability, accuracy, low-cost and simplicity of tools installation. In order to address this issue, a novel method has been proposed in this study. The method consists on using the image processing technique to automatically measure and track the deformations of concentrically braced frame (CBF) structures. Accordingly, the critical points in a CBF structure are first identified and the topological configuration of the structure is retrieved. The points and topological configuration characterize the basic shape of the structure. In this way, the deformation of the structure can be determined by measuring and tracking these points and their topological configuration. To show its effectiveness, the proposed method has been tested against the manual deformation measurements.

Aug 1, 2013

PROFIL D&apos;ENTREPRISE Léandre Gervais & Associé(e)s est une société d&apos;experts-conseils en ingénierie de la structure, de la mécanique & de la tuyauterie, et de l&apos;électricité et de l&apos;instrumentation. Nous offrons des services hautement spécialisés à notre clientèle des secteurs industriels des mines et de la métallurgie, au Québec, au Canada ainsi que dans plusieurs autres pays du monde. Notre mission est d&apos;assurer à nos clients un ensemble de services d&apos;ingénierie de haute qualité contribuant à la mise en oeuvre et à la réalisation de leurs projets d&apos;affaires. Léandre Gervais & Associé(e)s emploie 36 employés à temps pleins et opère à partir de Val-d&apos;Or, province de Québec. SERVICES OFFERTS Nous avons réalisé de multiples mandats pour notre clientèle de différent pays du monde dans les domaines d&apos;expertise les plus variés : ?Études de faisabilité ; ?Ingénierie conceptuelle ; ?Ingénierie de détail ; ?Gestion de projets ; ?Ré-ingénierie de la maintenance.

May 1, 2001

By Horace Freeman

Introduction In the aggregate, directly and ?indirectly, the pulp and paper industry ? consumes very large quantities of a variety of minerals, or compounds prepared from minerals. This is especially true in the manufacture of news-print, but fine papers, also, account for some of this consumption, in the processes of loading, coating, and otherwise improving the finish. The more important of the minerals used in the industry in Canada are briefly dealt with in the following pages. The list is by no means exhaustive, however. Thus, barite, lithopone, zinc oxide, zinc sulphide, and titanium oxide are used in small quantities in Canada in filling and coating paper. Up to the present time, however, the quantities of these materials used in the paper industry have not sufficed to encourage their manufacture in Canada. In the case of barite (barium sulphate)-or of witherite (barium carbonate)-it may be said that, should deposits of commercial size be discovered in Canada, the ore would have considerable export value, for use in the paper and other industries. China-Clay (Kaolin) Considerable quantities of china-clay are used for brightening and improving the finish of paper, and there is a growing tendency to use larger amounts of this material in newsprint manufacture. No china-clay suitable for paper manufacture is at present produced in Canada, but samples have been forthcoming recently from a deposit near St. Remi d&apos;Amherst, Labelle county, Que., about thirty miles north of the Ottawa river and approximately midway between Montreal and Ottawa, and plans are under way to conduct large-scale tests with this material. Present sources of supply are the United States, England, and Russia.

Jan 1, 1934

By J. Mirza, E. Nicol, J. Lipkowski

Gold passivation in thiosulfate leaching media is a major barrier to its implementation. Addition of Cu (II) into the leaching solution has shown to aid in gold dissolution, but the mechanism by which it acts, and its role in the passive layer, remains unknown. Surface Enhanced Raman Spectroscopy (SERS), in tandem with linear sweep voltammetry, were employed to determine the dependence of leaching currents on mass transport and for fingerprint identification of sulfur species on the surface of gold. SERS leaching experiments were performed using gold nanorod electrodes that showed increased stability compared to other SERS active surfaces.

Jan 1, 2011

By Jean Robitaille

La découverte du gisement du puits Penna a nécessité une révision complète de tous les circuits du concentrateur Laronde pour permettre, premièrement, l?adaptation du procédé à la nouvelle minéralogie et deuxièmement, l&apos;accroissement du tonnage de 1800* à 4500 t/j. Aux circuits existants de broyage, de flottation du cuivre, de cyanuration et du charbon en pulpe, les circuits suivants furent greffés : broyage semi-autogène, flottation du zinc, manutention des concentrés (épaississage, filtration, entreposage et chargement automatisé), décantation à contrecourant et précipitation au zinc, destruction des cyanures et remblai en pâte. Cet article se veut une revue des différentes étapes du projet d&apos;agrandissement du concentrateur qui se sont effectuées par phases progressives de 1997 à 2000. De plus, une description des nouvelles technologies sélectionnées et implantées est présentée.

May 1, 2001

By Henry Smith, Stu Brown

"The Williams Mine is Canada&apos;s largest gold producer, with annual production of some 500 000 ounces of gold from two million tonnes of ore. Highly mechanized and automated underground mining practices are utilized at the property in order to help achieve high levels of productivity and the most cost-effective mining possible.Planning and design parameters for the underground ore handling system at the Williams Mine are described in this paper. Particular reference is made to the considerations that were built into the system to provide maximum operating flexibility through the use of multiple orepass systems, portable low profile jaw crushers, underground conveyors and automated hoisting equipment.IntroductionThe Williams Mine is situated in the Hernlo area of northwestern Ontario, approximately 40 Ian east of the town of Marathon (Fig. I). It is operated by the Williams Operating Corporation, which is owned equally by Teck Corporation and Corona Corporation, and is one of three adjacent properties forming the HernIo gold camp.The mine commenced operation in October 1985 at a nominal production rate of 3000 tpcd. Through an ongoing capital development program, winch was completed in late 1989, the production rate at the property was increased to its current level of 6000 tpcd. This paper describes the mine planning process and the evolution of current mining strategies with particular reference to the underground ore handling system .HistoryGold mineralization was discovered in 1944 in the Hemlo area of Northern Ontario, near the north shore of Lake Superior. A year later, 11 claims were staked over the showing and subsequently patented by the late Dr. Jack Kerr Williams.Over the next 35 years, other claims were subsequently staked, explored and abandoned in the immediate area of the 11 patented claims . In 1980 a predecessor of the Corona Corporation acquired claims adjoining the Williams property to the east. Drilling on this claim group started early in 1981 and intersected the Hemlo orebody in May of that year. In December 1981, Corona Corporation entered into an option agreement with Teck Corporation to explore and develop the property.A drilling program by LAC Minerals on the II patented claims discovered the Williams orebody in March 1982. The mine started production in 1985, pouring its first official bar of gold on December 6 of that year. Corona Corporation was awarded ownership of the Williams Mine conclusively by a decision of the Supreme Court of Canada on August 11, 1989. The court&apos;s ruling ended a legal dispute with LAC Minerals over the property initiated eight years earlier."

Jan 1, 1991

By S. Zador

"IntroductionIn the past decade, metallurgical and mining companies have shown an increased interest in the licensing of technology. When licensing technology, it is usually to the benefit of the parties, to have at least some of the technology to be licensed protected by a patent.This paper is intended to bridge the gap between the engineer in the field of mining, metallurgy and mineral processing who is interested in exploiting an invention commercially, and the patent agent or intellectual property lawyer whom he/she might retain to prepare a patent application and then prosecute the application to obtain a granted patent. It is also intended to encourage the inventor or a small business concern to consider the value of patents in the sale and licensing of technology. The lawyer may subsequently advise and assist the inventor in licensing his/her invention.A brief outline of some of the basic features of the patent system follows. The nature of the information, which the patent professional requires from the inventor to enable him/her to draft a patent application, will also be considered in general terms. Furthermore, various types of licenses which may be drawn up between a licensor of specific technical information and a licensee, will be listed and briefly discussed. No attempt, however, will be made to give a comprehensive and detailed account of the above aspects; the interested reader should consult legal publication and reference books, and patent professionals for further specific information.A granted patent is a document which describes an invention and how to practise it. The claims of the granted patent, figuratively speaking, fence off the intellectual property the inventor regards as his invention. The Commissioner of Patents, representing the Government, grants to the inventor or his assignee the exclusive right of making, constructing and using the invention, and selling it to others to be used, for a limited period of time, in exchange for disclosing the invention to the public. Thus, a patent prevents others from practising the claimed invention but it does not, necessarily, bestow the right to the patentee to practise his own invention. The term of a patent now in Canada and in most of the developed countries of the world, is 20 years from the date of filing the patent application. In the United States the patent term is still 17 years from the date of issuance of the patent. In Canada, the term was changed to 20 years in the new Canadian Patent Act which came into force on October 2, 1989. Any patent application filed prior to that date or granted before it, retains a 17 year life, commencing at the time of grant."

Jan 1, 1991

By James F. Allan

"Abstract -The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec . Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by ? 0.10% Y203, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% Zr02. The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and cale-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and rninor britholite. Yttrium also occurs in britholite in cale-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m&apos;). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This &apos;sub-aerial&apos; deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

By H. Dundar

An extensive testwork was performed around the HPGR plant at GoldFields Ghana Limited Tarkwa Gold Mine. The HPGR was used to prepare the feed for heap leaching. The circuit was configured in such a way that the edge material from the HPGR discharge was recycled for further crushing while the product from the centre reported to the heap leach section. The set-up of the Polysius HPGR provided an opportunity to study the effect of different design and operating variables. This paper will discuss the results from the tests performed to assess the effect of rolls? speed and applied pressure on the capacity and the grinding efficiency of the HPGR. Applying different pressure values appeared to have an influence on the amount of edge material recycled.

Jan 1, 2012

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By W. M. Tupper

Municipal governments recognize the importance of aggregates in the local economy and the need to manage this resource in the interest of the public good. They have encountered problems with regulating the industry and the dichotomy between the urban need and the rural source. They have suffered from a lack of financial benefit, an adequate aggregate inventory, provincial strategy, economic information and public understanding. A provincial strategy for ensuring the availability of aggregate supplies to developing areas of the Province is essential. The Province should also be responsible for licensing, research, technical expertise on rehabilitation, public education and financial assistance. Upper-tier municipalities (regions or counties) should assume responsibility for resource management, including resource availability, demand characteristics, truck routing, phasing of resource development and sequential land-use planning. Area municipalities (towns and townships) can best determine the social and environmental impact of a specific aggregate development proposal and should therefore have the primary responsibility for the location of new pits and quarries. They should also have the authority to supplement provincial regulations concerning operating standards and the phasing and standards of site rehabilitation.

Jan 1, 1978

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By W. A. D. Edwards

"The Edmonton region accounted for 40% of Alberta&apos;s sand and gravel production in 1981 (about 12 million m3). Most of this production was by commercial operations (75%) for use in essential public works projects (64% in road and asphalt production).Although the Alberta Geological Survey delineated 1157 million m3 of gravel, a number of areas are considered to be in short supply. An econometric model was used for forecast demand in the region. Predictions, based on this forecast and estimated supply, are that 15% of the region&apos;s gravel and 3% of the sand will be consumed by the year 2010.The City of Edmonton is the largest consumer of aggregate in the region. Approximately 40% of the gravel in Edmonton&apos;s current supply area (about 55 km radius) will be used by 2010. These estimates are considered optimistic because the supply figures do not account for sterilization of deposits - some has already taken place in the region. If 25% to 50% of Edmonton&apos;s current supplies (one major deposit) were sterilized it would result in $1,000 million of additional cost due to increased haulage alone.Information on the value of aggregate resources, the location of sand and gravel deposit s and forecast demand has been made available to all municipalities in the region to aid planners and regulators in effective future use of this important resource.INTRODUCTIONAlberta is the second largest producer of sand and gravel in Canada at ab out 50 million tonnes annually. Value of provincial production exceeded $120 million in 1985. In Albert a, aggregate is used primarily in road and building construction (about 50% and 15%, respectively) and is important in such activities as petroleum exploration, oil sands development and the forestry industry.The Edmonton region (Fig. I) accounts for about 40% of provincial production and has a per capita consumption rate of about 13.4 m3 of sand and gravel per annum. Although Edmonton dominates, with approximately 50% of regional production going into the city, aggregate is produced in every county and municipal district in the region.Sand and gravel is essential to the current way of life in the Edmonton region. The resource is valuable and dwindling. The Alberta Geological Survey (a department of the Alberta Research Council) has collected information on aggregate in this region for the last decade which ca n aid government planners and regulators in pre venting sterilization and misallocation of this critical resource. This paper is a summary of that information."

Jan 1, 1989

By J. J. Emery

There is an increasing awareness on an international level of the potential for utilizing many wastes and by-products as construction materials. This has resulted in recent major reviews by OECD and RILEM to supplement national activities by agencies such as CANMET, USBM, BRE and LCPC. Much of this international and national work was reported during an International Conference on the use of by-products and wastes in civil engineering held in November 1978 in Paris. Based on participation in the OECD and RILEM reviews, and the Paris conference, developments in waste and byproduct utilization of particular concern to Canada are described. The major technical and economic constraints involved are also reviewed, so that the over-all evaluation reflects important factors such as inherent variability and transport logistics. Areas requiring further research and development are also identified. Particular emphasis is placed on slags, salvaged asphaltic concrete and surplus sulphur. "Due to the rapid development of China&apos;s industry, more than a hundred million tons of industrial wastes are generated annually, which occupy lots of land for storing, bring about environmental pollution, obstruct industrial and agricultural production and cause harm to people &apos;s living. Therefore we must utilize them effectively to create wealth for our country. "

Jan 1, 1979