Search Documents

By X. F. Liu, O. Buzzi, Y. Sieffert

This study falls in the context of underground coal fires (UCF) where burning coal can elevate the temperature of a rock mass in excess of thousand degrees. The objective of the research was to experimentally investigate the change in mechanical behavior of a rock when subjected to temperatures up to 900 °C. Several blocks of an Australian mudstone were collected from a mining site in New South Wales, Australia. X-ray diffraction and thermal-gravimetric analysis were conducted on powdered rock in order to determine the critical temperatures at which the main mineralogical changes occur. Then, cylindrical specimens were prepared from intact rock blocks for unconfined compression tests. These rock specimens were then treated by heating in a temperature-controlled furnace at temperatures varying from 100 °C to 900 °C. The heating process consisted of two stages: raising temperature with very slow rate of 1 °C per hour followed by a holding period of 24 hours and then a slow cooling process to room temperature. The compression tests were carried out on treated rock specimens to characterize the change in compressive strength. The macroscopical study was complemented by microstructural investigations via optical microscope, scanning electron microscope (SEM) and mercury intrusion porosimetry (MIP). Results show that the unconfined compressive strength of mudstone decreases with increasing heating temperature up to 450 °C, beyond which it increases. This can be explained by the combined effects of micro cracks and mineral thermal reactions caused by heating process.

Jan 1, 2015

By F. Czerwinski

Mechanically fragmented chips of an AZ91D magnesium alloy were transformed into a semisolid slurry within the Thixomolding® system. Microstructural analysis of a material at various processing stages revealed that the cold deformation of the alloy, experienced during chipping, led to the recrystallization and growth of equiaxed grains which were subsequently converted to the globular structures by melting the grain-boundary network.

Jan 1, 2004

By David Penswick

Despite anecdotal evidence to the contrary, the mining industry is not in decline. Rather, the world?s largest mining companies are among the most consistently profitable companies in any industry. In many cases, profitable mining companies have been built around a few large scale, long life mines. These criteria for success ? size and long life ? have led to the current preference for deposits that can be exploited using open pit methods. However, developments in the science of block caving have resulted in this mining method achieving costs and productivities that are competitive with the largest open pits, while achieving widespread applicability. One implication of the low costs and widespread applicability of block caving is that some current open pits are possibly too deep.

May 1, 2003

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting pre-concentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gem stones.

Oct 1, 2009

By Kai Bartram

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting preconcentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gem stones.

May 1, 2009

The influence of joint orientation and joint persistence, on the mechanical behaviour of jointed rock masses under uniaxial compression, has been studied systematically. The joint inclination angle ß was varied from 0° to 90° with an increment of 15°. The joint continuity factor k was taken as 0.2, 0.4, 0.6 and 0.8. The peak strength, Young’s modulus, the complete axial stress-axial strain curves, the cracking process and the characteristic of the fragments, were investigated. It was found that the anisotropic response of the jointed specimens was governed by the micro-mechanism, such as crack initiation, propagation and coalescence, crack opening or closing, and frictional slip of cracks or joints. With the increase of joint continuity factor, the axial stress-axial strain curves change from single-peak to multipeak, the peak strength and Young’s modulus decrease. The specimens with medium joint inclination angle (30°,45° and 60°) has lower energy dissipation and strength due to stepped or shear failure, while specimens with small and large joint inclination angle (0°, 15°, 75° and 90°) has higher energy dissipation and strength due to axial cleavage or crushing failure.

Jan 1, 2015

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By S. Simukanga, J. Masinja, P. A. Bepswa, A. N. Mwale

Screening is an important operation in dry and wet closed circuit mineral processing applications. Most of the operations have seen the benefits of using fine wet screens in primary grinding sections where the product is relatively coarse, and screens can handle the tonnage. Although many models are available, most of them are confined to dry and wet coarse screening applications. Most models do not give good predictions for wet fine screening. To facilitate model development, pilot plant tests were performed using a single deck Derrick Screen at aperture sizes of 45µm, 75µm, 106µm, and 150µm. Experimental data for a range of feed solids concentrations and flowrates was collected and used to calibrate the performance of the screen under the different operating conditions. The results showed that the performance of the screen deteriorated with an increase in feed solids concentration, and, similarly with an increasing feed flow rate. The percentage of fines carryover also increased with the reduction aperture size. The carryover was even more pronounced at higher feed rates and solids concentrations. A model was developed for predicting the performance of fine wet screening. Data from the test work was used to compare the actual and predicted results, and to calibrate the model. Additional independent data was used to validate the model and assess its limitations. This model will give an expected screen performance based on the initial feed conditions. It incorporates screen design parameters that allow for an estimation of a suitable screen size for a desired performance based on given feed conditions. This paper discusses; the results from the test work performed, the model development and its limitations.

Jan 1, 2016

By G. N. Carlson, C. H. Hazelroth, D. R. Dorrance

"Located on the north shore of the St. Lawrence River at Pointe Noire, Quebec are the agglomeration and ship-ping facilities of the Wabush Mines complex. Here, the specular hematite concentrate from the Scully Mine is received for further processing. Modern facilities for handling the ore, either to the 1plant or to stockpile, provide quick and efficient operation of the ore receiving station. Physical preparation of the ore for balling is accomplished with regrind ball mills, filters, bentonite crushing and drying facilities, pumps and related conveying circuits. Rotating table feeders deliver the reground and de-watered ore from storage bins to balling drums, where green ball or green pellet formation is achieved. The green balls are then conveyed to the indurating section. Three Dravo-Lurgi travelling grates, producing a total of 6,000,000 long dry tons of pellets per year, are used in the indurating phase of the operation. These grates, having 38 windboxes and firing at a temperature of 2,500°F, harden the pellets for shipment to various blast furnaces throughout the world."

Jan 1, 1969

By A. J. Smethurst, S. B. Hearn, S. Boskovic

"The problem of crud in solvent extraction is well known and can be a major handicap and operational issue. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Flocculation can be utilized to remove some of the troublesome particulates but colloidal silica does not flocculate well and presents a different problem requiring innovative chemistry to solve. Coagulants can assist by facilitating the removal of this colloidal silica by promoting the agglomeration of the particles to a size which can be more readily settled or flocculated in solid/liquid separations. This is achieved when the coagulants bind to the surfaces, displacing water and destabilizing the colloids, whereupon they bind to each other which facilitate their amenability to conventional flocculation.INTRODUCTIONSilicate minerals are abundant in the upper layers of the Earth’s crust, and there are few mineral deposits without significant levels of gangue silicates. Silicate minerals include the pure silicas, such as quartz and other silicate containing minerals such as clays, chlorites, feldspars, as well a vast number of less common silicates.During the acid leaching of ores, two types of fine silica particles are released in solution from the dissolution of the host mineral. The first consists of partly depleted silicates, and the second is colloidal silica, which forms in solution. It is this second type which has the potential to cause crud formation as well as poor solution clarities, slow filter rates and excessive flocculant usage (Figure1)."

Jan 1, 2016

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By A. Jafarnia

Aluminum alloys are frequently grain refined during solidification in order to promote the formation of an equiaxed grain structure in the casting. The application of Ti-based grain refiners and/or Ti containing master alloys for improving mechanical properties may result in formation of Al-Ti based intermetallics. Although the grain refinement produces many desirable qualities in aluminum castings such as improved castability and mechanical properties, the addition of Ti to Al-Si foundry alloys may lead to the formation of some undesirable intermetallic particles such as AlTiSi and cause a number of operational problems such as nozzle blockage due to segregation and agglomeration of aluminide particles within the nozzle. There are several questions to be clarified when minor amount of Ti is added to Al-Si alloys. They include nucleation and growth of AlTiSi particles, their morphologies and orientation relationships with aluminum matrix and the dissolution of these intermetallics during the course of solidification and/or post solidification treatments. The current study was initiated to study the process and possible mechanism of aluminide dissolution and the related phenomena such as segregation and agglomeration. It reports the results found during reheating of laboratory prepared Ti-added A356 alloy at three temperature ranges of below solidus, mushy zone and above liquidus.

Jan 1, 2004

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By H. Al-Kazzaz

The effects of laser power and joint gap on the welding quality of 2-mm butt joints of ZE41A-T5 sand castings were investigated using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire at a welding speed of 6 m/min and surface defocusing. The smooth weld profiles with the minor welding defects were obtained at a laser power of 4 kW and joint gap of 0.3-0.4 mm. The hardness values in the fusion zone are similar to those of the base metal but there is a drop in the heat-affected zone after a natural aging of 18 months.

Jan 1, 2006

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate &apos;wetting&apos; of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By V. K. Karra

"A simplistic algorithm jar simulating the rod or ball mill Bond grindability test applied to ores and minerals is presented. A performance comparison between the present algorithm and a previously published algorithm by Kapurot, modified in this work jar a fair evaluation, is also given. A worked example is furnished jar leading the reader through the various calculations.IntroductionThe Bond grindability test is widely used for the prediction of the power requirement of an industrial grinding mill. The procedures for conducting this test in either a ball or a rod mill are available(1). In the case of a ball mill, batch grind abilities have been correlated to Bond grindabilities to help monitor day-today variations in ore grindability for the purpose of plant control( 2,3). Of special interest is the algorithm presented by Kapur(3) for the simulation of the Bond test. In practice, the test lasts from 6 to 14 cycles (4 to 10 hours). With this algorithm, one can predict the Bond grind ability using information available from only the first two cycles.Sometimes the prepared feed for the grindability test contains too much fines compared to the total product desired at the mesh of grind under consideration. In such a case, the operator separates the fines from the test feed and adds to the remaining coarse fraction an equal amount of fresh feed. This combined feed then forms the feed to the first cycle of the test. In the present work, Kapur&apos;s algorithm is modified to include this special case. A new and relatively simpler algorithm is also presented. Statistical equations relating work index to pertinent variables are also given."

Jan 1, 1981

By Andrea Lisjak

The mechanical behaviour of Opalinus Clay, an indurated over-consolidated argillaceous rock, is heavily influenced by the presence of preferably oriented bedding planes. The objective of this study is to illustrate a new modeling approach aimed at capturing the bedding-induced anisotropy of Opalinus Clay as observed in the laboratory and in situ. The combined finite-discrete element method (FEM/DEM) is employed as the main simulation tool. FEM/DEM is a numerical method that models material damage processes by explicitly considering fracture nucleation and propagation. A transversely isotropic elastic constitutive law is used to account for different elastic property values in the direction parallel and perpendicular to the layering, while strength anisotropy is captured using a directional cohesive fracture model. Quantitative calibration and validation of the model is based on laboratory results of indirect tensile tests and uniaxial compression tests. Emergent strength and deformation properties, together with the simulated damage mechanisms, are shown to be in good agreement with experimental observations. Preliminary results relative to the analysis of a circular tunnel show that the approach is able to reproduce the main Excavation Damaged Zone (EDZ) formation mechanisms as observed in the field.

Jun 1, 2012

By S. H. Castro

Molybdenite depression by shear degraded polyacrylamide solutions has been investigated. Aqueous solutions of polyacrylamide-type flocculants were subjected to shear degradation under a range of high-speed stirring conditions. Settling tests, carried out with quartz slurries and sheared polyacrylamides, showed reduced flocculant performance with increased degradation. As the sedimentation rate is strongly dependent on the polymer&apos;s molecular weight, these results fit well with the shear degradation theory, which predicts the production of shorter chain segments due to breakage of the polymer macromolecules. Microflotation tests on natural molybdenite showed that the depressing ability of a commercial polyacrylamide flocculant remained unaltered after shear degradation, even when the flocculating ability was entirely lost. Practical implications of shear degradation on molybdenite flotation are discussed.

Jan 1, 2004

By K. Sugawaral, W. Tongampl, K. Hiruta, Takasaki Y., A. Hosoi, T. Katol, A. Shibayamal

Printed circuit boards of discarded personal computers, televisions, mobile phones and so on contain a significant amount of valuable metals. For the recycle of valuable metals contained in the printed circuit board wastes (P CB W), the effect of temperature on chlorination-volatilization of metals under chlorine gas flow was studied. The experimental sample used was powder of two types: crushed PCBW (Sample 1) made from PC and industrial machines, and crushed-combusted PCBW (Sample 2) made from Sample 1. The principal element in Sample 1 and Sample 2 was copper, about 13 wt% and 20 wt% respectively. Sample 1 was composed of pure metals such as copper, tin and lead. In comparison, Sample 2 consisted of oxide metals such as copper oxide, tin dioxide and silicon dioxide. The two samples were heated at predefined temperatures (ranging from 300 °C to 900 °C) in chlorine gas. The chlorine gas flow into the furnace was set at a rate of 100 mL/min. As a result, copper in Sample 1 began to volatilize at 600 °C and completely vaporized at 700 °C. While in Sample 2, copper started to volatilize at 600 °C and reached 100% vaporization at 800 °C. For Sample 1, zinc finished volatilizing at 500 °C, while for Sample 2, zinc volatilization reached only about 80% (maximum). Also, lead, nickel and titanium showed similar results. Consequently the volatilization rate of Sample 1 is higher than Sample 2 and the temperature dependency was verified for copper, lead, zinc, nickel, antimony, titanium and chromium. In fact, the volatilization rate of these metals increased with the temperature. This result reflects the difference between pure metal and metal oxide, as Sample 2 was combusted before the chlorination-volatilization test. Moreover, the chlorination reaction may be accelerated by a reductive atmosphere because Sample 1 contains carbon. In this study, the volatilization behavior of some valuable metals in PCBW by chlorine gas was observed. Further improvement in the rate of volatilization can be achieved by optimizing the experimental conditions.

Jan 1, 2011