Search Documents

By Matthew Janes

Advantages: Clean samples Low sample disturbance Very low spoil Versatile Fast Penetrates all formations Resonant Drill 100 or 150 kW Self tuning to resonance Rotation to 100 rpm Increased depth in dense soil Increased productivity Reduce water use Reduce casing plugging

May 1, 2013

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Kristine Haug

Although most in situ operations in Alberta do not encounter significant problems during resource extraction, there have been a few documented occurrences of oil or steam releases as a result of compromised caprock seals. The objective of the Oil Sands Caprock Integrity Project (OSCRIP) is to characterize the units above and below bitumen zones to determine which geological factors affect the quality of the caprock seal. In addition, geomechanical properties and stress measurements of the bitumen reservoir and overlying units will be examined to provide a better picture of the containment conditions in which in situ operations occur. The information from this study will aid regulatory staff and industry in determining the zone-specific geological and geomechanical factors that could affect the design, operation, and feasibility of in situ recovery projects. The OSCRIP study area (Townships 87 to 99 and Ranges 1 to 13, West 4th Meridian) encompasses the surface mineable area, the northeast extent of the Wabiskaw-McMurray bitumen deposit and the Clearwater Formation, as well as a wide band of the Devonian salt-dissolution zone. Regional geological mapping of the Cretaceous strata focuses on the spatial extent and thickness of the caprock seal. Mapping of the underlying Devonian strata is targeted at better understanding the potential effects of salt dissolution and collapse of overlying strata on the integrity of the caprock seal. Examination of LiDAR (Light Detection And Ranging) bare earth DEM in the study area has revealed localized depressions that may represent sinkholes rooted in subsurface collapse features in Devonian carbonate and evaporite strata. Mapping the location and understanding the timing of salt dissolution-related features and deformation in the Devonian strata will help address questions about the possible effect that geological structures, such as sinkholes, have on the integrity of the caprock, as well as the potential for localized variations in the stress regime of the bitumen zone and overlying units. The stress regime in units above 350 m is such that any induced fractures are believed to be horizontal, and therefore, there would appear to be no mechanisms that would allow these fractures to reach the surface. However, recent incidents have shown that vertical pathways can occur, linking the subsurface to the surface. The final phase of the project will evaluate the changes that may occur in the stress regime under thermal operating conditions in the study area.

Jun 1, 2012

By A. J. Rigby

Anode vessels are often relined with refractory every one to two years and a typical reline time can take between 16-20 days. Modem refractory designs using dense, corrosion resistant brick applied directly to the vessel shell in the high wear areas around and above the tuyeres and at the slagline can yield a lining life of up to 4-5 years before a complete reline is necessary. Installation methods using brick delivery on roller conveyors through an endwall access port and complete anchoring of the brick to allow for lining self-support can take days off the installation time. It is possible, therefore, to reduce the refractory relining period by 50% and increase lining life by 100% compared to typical anode repair schemes. Cu2007

Jan 1, 2007

By P. J. Poirier, J. A. Meech, H. Raabe

"An Expert System has been implemented to assist operators in applying knowledge about froth conditions in the control of the flotation circuit at Highland Valley Copper. For some time, the personnel at Highland Valley Copper have recognized that froth type is a useful indicator of good operating conditions. However, the operating strategy based on froth type recognition is an ad-hoc skill in which different operators use a variety of terms, features and procedures to identify and solve problems. The first phase of this project developed an on-line consultative system to advise and tutor so that the diffuse expertise could be rationalized and consolidated into a standardized format.The second phase has brought this knowledge into a real-time environment to advise the operators on the floor in identifying froth types and troubleshooting corrective action. This paper describes the steps taken to acquire the knowledge, to design the required system features and to implement the real-time version of this system.INTRODUCTIONThe use of expert systems in the mineral industry has been gaining popularity in recent years. Minnova Inc, Les Mines Selbaie, Wabush Mines, Potash Corporation of Saskatchewan are just a few examples of Canadian mining companies that use expert systems to monitor or control their plants. Applications in the field of flotation include Brenda Mines (Edwards, 1992), Mt Isa Mines Ltd (Lacouture et al, 1991), Outokumpu (Karhu, 1989) and Kidd Creek (Burrows et al., 1989).Expert systems are defined as ""computer systems that apply reasoning methodologies on knowledge in a specific domain in order to render advice or recommendations much like a human expert"" (Turban, 1988). The main areas of application are diagnosis, training, process monitoring and control, and design. There are basically two main types of expert systems: Consultative systems, which are off-line applications in diagnosis and design, and on-line realtime systems, used for supervisory process control and real-time advising."

Jan 1, 1993

By Chris Carr

This paper describes the process employed and the work undertaken to enable the surrender of the mine permit relating to the two tailings deposits at the abandoned Red Mountain Mine site near Rossland, BC. The first phase of the work undertaken was to provide urgent remedial work for protection of the environment, primarily through rehabilitation or replacement of surface water drainage systems. The second phase was to up-grade the water management systems to the appropriate level given their consequences of failure. The final phase of work is to ensure long term geotechnical stability of the facilities to the same level of risk. Establishment of a sustaining fund will facilitate long term monitoring and maintenance of the facilities.

May 1, 2002

By Si Qin

Unknown goafs and roadways of abandoned coalmines can be a great water inrush hazard for coalmine workers. Consequently, advance detection of such hazards is of great importance. By detonating seismic charges in underground coal seams, we can collect seismic data using a surface survey line, which is located across the ground projection of the underground shot point. This experiment was conducted in a coalmine in Shaanxi Province, China. After surface elevation compensation and travel time adjustments, we accurately determined the position of the goaf boundary along the survey line based on the wave velocity anomaly on the seismic record. Then we used a scattered wave imaging technique to enhance the energy of the scattered waves that are generated when the coal seam roof slide wave (refracted wave when the incident angle bigger than the critical angle) hits the roadway, thus confirming location of a geological discontinuity (roadway). This experiment shows that the coalmine ground seismic method, employing an underground explosive charge and a surface seismic array, has the ability to detect an abandoned roadway and goaf in advance of coal mining, thus can improve worker safety.

Aug 1, 2013

By Z. D. Hora

Commercial production of barite commenced in British Columbia in 1940; shipments have been recorded from ten deposits, of which four are particularly significant: The Brisco, Silver Giant, Parson, and Mineral King mines. Parr of the barite production is a by-product of base metal deposits in which barite is a major gangue mineral. About one hundred occurrences are known. COMMERCIAL production of barite in British Columbia dates back to 1940. Production volumes rose and fell and reached 39,900 tonnes in 1972. The main producer is Mountain Minerals Limited . There are two principal areas of barite deposits in British Columbia: ( I) The southeast part of the province along the Rocky Mountain Trench , which is the source of all production to date. (2) Stratabound occurrences in northeast British Columbia in the Gataga-Ketchika rivers and Muncho Lake areas which are not yet developed. Of the approximately one hundred reported barite occurrences, only ten have recorded commercial shipments, some of insignificant amount. So far, four deposits have proved to be important producers: Brisco, Silver Giant, Parson and Mineral King. The Mineral King property is situated near the confluence of Toby and Jumbo Creeks, 35 km southwest of lnvermere. The lead-zinc-copper-iron-barite deposits, as described by Fyles (1959, 1962), replace Proterozoic Mount Nelson dolomites of the Purcell system on the limb in the trough of a complex, tight syncline. The mine operated from 1954 to 1967 and 2,097,900 tonnes of baritic ore that was processed for base metal concentrates and also produced 22,680 tonnes of by-product barite. Since 1970, some 136,000 tonnes of barite have been recovered from the old tailings pond. The deposit is now considered depleted. The Silver Giant mine is located 10 km northwest of Spillimacheen. Barite and lead-zinc sulphides replace Cambrian Jubilee limestone near their contact with the overlying Ordovician McKay slate. Mineralization is located in the nose of an overturned plunging anticline. Between 1951 and 1957 800,000 tonnes of baritic ore were processed for lead and zinc concentrate. After 1959 barite was also produced , first from open pit, and later from reworked tailings. Up to 1979 production of barite totalled approximately 180,000 tonnes. Two other producing mines in the area are descri bed by G.R. Manson (this volume). Large, bedded stratabound barite deposits are reported from northeastern British Columbia. Six major shale-hosted Industrial Minerals in Canada lead-zinc-barite occurrences are known in the Devonian Gunsteel Formation. These are: Driftpi le Creek, Mount Alcock, Cirque, Pie, Fluke and Elf. In addition, numerous occurrences of strati form blebby or nodular barite and locally massive white crystalline barite are known from the Driftpi le Creek and Ak ie River districts in Gunsteel shale and from the Kechika, Road River and Ware map areas from Silurian siltstone . The size of these deposits is impressive; the baritic horizon at Mount Alcock is reported to be 25 to 30 m thick , and dri ll ing results from the Cirque deposit indicate reserves of 30 mi llion tonnes of baritic lead-zi nc-si lver ore. Similar bedded barite deposits are also reported from Midway area, near the Yukon border.

Jan 1, 1984

By S. Hussien, P. Somasundaran, P. Patra

"Rare earth elements (REEs) are essential for many applications in electronics, energy harvesting, and defense. The common resources for economic extraction of REEs are oxides such as bastnaesite and monazite, which are scarcely available in the earth’s crust. On the other hand, REEs are available in many clay and phosphate ores where REEs substitute Ca or Si in the mineral lattices or as physically adsorbed cations at negatively charged sites on the clay surface. While REE oxides readily dissolve in acid, making the chemical leaching of REEs an economically viable option, adopting a similar approach for leaching of silicates and phosphate ores is unfeasible because of significantly low REEs content in these ore deposits. Bio-leaching approaches are environmentally benign and economically viable. We investigated the bio-leaching (Acidothiobacillus ferrooxidans (Af) and the fungal Aspergillus niger (An)) of REEs from a phosphate ore, and examined the factors governing the leaching processes. Based on the shake flask leaching studies, an increase in surface area combined with an increase in pulp density (1-15 wt. %) was found to lead to an increase in the amount of REEs leached. In contrast, an increase in the surface area by reducing the particle size from 75 to 35 led to a decrease in the amount of REEs leached. These differing attributes are proposed to be due to the poor bacterial growth/activity with high F- ions in the leaching media, F- released from the edge-sites of the smaller particles. On the other hand, several advantages that associate with the Af bacterial bio-leaching processes relate to the media composition (Mg2+ and (NH4)+) and phenomena occurring at the electrical double layers of the mineral and bacterial- water interfaces. These studies suggested that leaching of particles occur in a layer-by-layer manner.INTRODUCTIONRare Earth Elements (REEs) are essential for many important applications, such as in electronics, energy generation, and defense. The common resources for economic extraction of REEs are typically carbonates such as bastnaesite and monazite, which are scarcely available in the earth’s crust (Y. Kanazawa and M. Kamitani, 2006). REEs are abundantly available in many clay and phosphate ores where REEs substitute Ca or Si of the mineral lattices. Conventional acid leaching of REEs from oxides is not economically feasible for clay and phosphate ores because of significantly low REE content (parts per billion) in these ores (Tian, J., Chi, R., Yin, J., 2010a; Moldoveanu G. A. and Papangelakis V. G., 2013; WK Goyne, LS Brantley and J Chorover, 2010). In some cases, REEs could be extracted from these ores via chemical leaching routes as they constitute reasonable amounts of REEs (0.1 - 1% REEs). A major challenge faced in general in chemical leaching processes (Chi, R., 1988) is the loss of REEs in the phosphate/gypsum precipitates/crystals, which are overcome in a step-by-step manner by sequentially removing impurities such as fluorine and calcium, including steps carried out at elevated temperatures. On the other hand, bio-leaching approaches provide environmentally benign and economical alternatives. Acidophilic bacteria are currently being used for industrial scale bio-leaching of Au/Cu/Ni from low grade ores. Studies on bioleaching of REEs from red mud (Al2O3) using Penicillium tricolor and Aspergilus niger (An), and, of bio-leaching (lab-scale) of phosphate rocks using Acidithiobacillus ferrooxidans (Af) have been reported (Boon, M., Heijnen, J.J., 1993; Qu, Y. and Lian, B., 2013). We conducted bacterial (Af) bio-leaching of REEs from a phosphate ore in shake flasks and columns, while examining the key factors that govern leaching kinetics."

Jan 1, 2016

By PETER O. SANDVIK

The Cargill deposit, located 32 km south west of Kapuskasing, Ontario, was discovered by International Minerals and Chemical Corporation in 1975 and has been evaluated through an extensive program of drilling, chemical analyses, metallurgical tests and engineering and economic studies. The Cargill alkalic complex, comprising mainly carbonatite and pyroxenite-amphibolite rocks, was intruded into the rift system of the Kapuskasing magnetic-gravity high. Weathering and leaching under assumed temperate to cool climatic conditions plus faulting, shearing and/ or initial petrographic variations within the carbonatite developed a small, locally confined karst system. This resulted in a thick enriched leached carbonatite zone capped by troughs and sinks, and filled with a residuum of apatite, goethite, clay and other minerals. Residuum thickness ranges from nonexistent on ridges to 170 m in troughs and sinks. Apatite values are 5 to 15% in fresh carbonatite, 20 to 40% in leached carbonatite and 20 to 98% in residuum. A tentative open-pit mine designed for preliminary feasibility studies is estimated to contain 62.5 million tonnes averaging 19.6% P20 5.

Jan 1, 1984

By Ronald C. Schimmel

In 2006, the Corus IJmuiden pellet plant produced approximately 4.6 mln tonnes of pellets. Corus IJmuiden is about to increase its pig iron production to 6.4 mln tonne HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50% high basicity sinter and 50% acid pellets, both produced in-house. To enable an increased iron production, the capacity of the pellet plant needs to be raised to 5.0 mln tonne per annum. The capacity is increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

May 1, 2007

By M. L. Free

Laboratory scale extraction of metals from heterogeneous materials such as copper ores is often performed using fine material to increase kinetics and reduce sample size requirements and costs. In contrast, commercial extraction is usually accomplished using much larger material sizes than are used in laboratory settings. The large size difference between laboratory testing and commercial application materials makes it difficult to use laboratory test data to accurately predict performance for commercial material. One solution adopted widely in industry is the use of large test columns. Large test columns cost considerably more to set up and run and take much longer periods of time to evaluate than laboratory scale tests with small particles. Consequently, from a cost and data collection efficiency perspective, the development of accurate scale up methods offers significant potential for saving both time and money. This paper provides details for a new approach to correct for scale-up phenomena in heterogeneous material processing.

Jan 1, 2007

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By P. J. Foster

Bowtie analysis has recently emerged as a technique of choice that can be used when looking specifically at major hazards in the mining industry. A Bowtie diagram is a graphical means of assessment that focuses on identifying all the specific causes and consequences of major events, from which all the ?pre-event? and ?post-event? control measures can be identified. From this critical control measures can be identified and monitoring/assurance systems can be established. It is this assessment of control measures and their effectiveness that replaces the more traditional evaluation of risk (using matrix-based approaches) based on the fact that risk is a function of control ineffectiveness. This is a major difference with traditional risk assessment where all too often control effectiveness is assumed. This paper summarises the Bowtie analysis process and outlines one specific case study where the technique was used on the unwanted event of a collision of a haul truck and light vehicle in an openpit mine. Although more effort is required in undertaking the assessments, control assurance provided this way will go a long way in ensuring that risk assessments and major hazard management become much more effective in practice.

Aug 1, 2013

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

By Richard Q. Fox, Joe L. Pinson

This paper provides guidelines jo1• analyzing and selecting electric power demand controlled. Error calculations, load selections and timing criteria are identified as the three key functions which affect the suitability of a demand controller for any particular application. The advantages of simulating the demand control application on a computer are described, and applications of a demand controller to an iron ore concentrator and a copper refinery are shown. Finally, the paper studies the return on investment for a demand controller.

Jan 1, 1976

By M. Vaccarini

In this paper a possible methodology to supplement a predictive control approach is reported. The benefits deriving from the application of a predictive control on complex buildings lay on its capability of adapting in advance to the conditioning needs of indoor environments. In fact, the mere reactive control is usually affected by response delays, mainly determined by latency intrinsic in systems and by the massive nature of buildings, which slows down their response to changeable inputs. Hence, systems are too often solicited at their maximum power to recover against comfort deficiencies, and high consumptions are had. This paper reports on the application of a predictive approach to the Passeig de Gracia (PdG) metro station in Barcelona, which is a considerably high energy demanding building and where ventilation systems are used to control both comfort and air quality. Although an extensive simulation for estimating energy savings obtainable through that approach is currently ongoing, in this paper we detail the several components which make up a ?predictive control framework? and we perform a preliminary demonstrative simulation. In particular, the whole setup is formed by: a detailed model of PdG, which simulates the station?s ?real state?; a control model, which optimizes a given cost-function; probabilistic predictive models to infer the future state of the systems, given the assumptions on the control actions by the control module. The outcomes of this paper show that the procedure is applicable and preliminary results over a short simulation horizon of half a day are reported.

Aug 1, 2013

By Nancy E. Wilk

In 2015, more than 1.2 million deaths annually were estimated to be caused by occupational risks (WHO, 2018). In 2021, this estimate increased with the publishing of the World Health Organization (WHO) and the International Labour Office (ILO) Joint Estimates of the Work-related Burden of Disease and Injury based on data from 2000 to 2016 (WHO/ILO, 2021). These global estimates reported that each year 1.9 million people die from exposure to occupational risk factors, 81% of these fatalities resulting from non-communicable, occupational diseases. WHO/ILO notes that the health-related risk factors with the largest number of attributable deaths were exposures to long working hours followed by workplace exposures to particulate matter, gases, and fumes. The health outcome with the greatest work-related burden of deaths was chronic obstructive pulmonary disease, followed by stroke and ischaemic heart disease. In considering the 2021 data published by WHO/ILO, it is likely that the estimates are low and underestimate the true burden of occupational disease and injury. In support of that position, more recently the ILO estimated that “2.3 million women and men around the world succumb to work-related accidents or diseases every year; this corresponds to over 6000 deaths every single day” (ILO, 2022).

Jan 1, 2023

By Seunghoon Lee

The increase in the number of higher and larger buildings is expected to require the buildings' outer wall maintenance process, which includes cleaning, painting and monitoring, still depends on manpower. In this study, we proposed the robotic building maintenance system and aimed to reduce the jerk effect through the motion control of the system, improve the performance of the maintenance task, and ensure longer life and safety by improving the stability of the building structure and robot system. Through the results of the motion control and field-test with the proposed system, in specific, horizontal sliding module (HSM) showed that the jerk oriented by impact force was significantly reduced, feasibility of the proposed method was verified, and the robotic challenges were explored.

Aug 1, 2013