Search Documents

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By J. W. Merks

"The accuracy of a measurement on minerals and ores can be assured by applying suitable and unbiased procedures but its precision is a function of the number of primary increments and their mass, the number of lots per consignment or samples per shift, and the number of measurements on analysis fine samples.Experimental data will be used to show how the variance components for sampling, sample preparation and analysis contribute to the total variance on which precision statements for the final measurement are based. This type of experiment should not only form part of quality control programs at mines and smelters, but also underly the criteria on which the design of manual sampling regimes and mechanical sampling systems for bulk solids and slurries should be based.Sampling systems and regimes can only be adjusted and optimized if the variance component for each step in a quality evaluation process is measured. Knowledge of precision characteristics lies at the core of effective loss prevention and control programs."

Jan 1, 1985

By H. R. Wilson

"This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1988. The program was developed in response to the terms and conditions of the Water Licence issued to the mine in 1981 by the Northwest Territories Water Board. Echo Bay Mines Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle.The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that the total containment concept would require reevaluation since discharge from the pond would be required within a few years. During the initial years of production, an investigative program was established to determine the most effective means for treating the tailings pond water. This program incorporated both laboratory studies as well as monitoring of the tailings pond contents and environmental conditions as the impoundment area was filling. The program showed that natural degradation phenomena, if properly utilized, are effective in lowering the concentrations of all contaminants to within Licence limits with the exception of arsenic. To ensure compliance with arsenic limits, an iron salt was added to cause arsenic to precipitate from solution in the tailings pond.As a result of our studies, the tailings management system finally implemented at Lupin Mine includes the following components:Tailings pulp retention cells constructed by dyking off one end of the tailings impoundment area.Two tailings ponds in series operated in a sequential decant and fill fashion.An iron salt solution preparation and metering system.A syphon system into which the iron salt solution is injected as the contents of the first pond are decanted into the second pond.A second syphon system for decanting the contents of the second pond to the receiving streamThis paper discusses the findings and conclusions of the waste management investigative program, describes the civil work completed to reach our final operating scenario, describes the sequence of operating the treatment system, reviews performance data, and comments on abandonment and restoration of the tailings impoundment area."

Jan 1, 1989

By Michel Ruel, Ali Soltanzadeh

This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control and expert systems such as fuzzy logic controllers and neural networks. Three examples are presented: ARC (Advanced Regulatory Control) on pH in a comminution circuit, MPC (Model Predictive Control) for combustible management and FLC (Fuzzy Logic Control) on a Semi Autogenous Mill. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.

Jan 1, 2014

By D. B. Nazzer

"ANY DISCUSSION of energy today is incomplete without consideration of nuclear energy. In the Maritimes, with plentiful supplies of coal, with relatively easy availabilty of imported oil brought in to the deepwater terminals, with future sources of large supplies of oil and gas anticipated from under our neighbouring continental shelf, and with the Fundy tides, you may question why nuclear energy should be considered. What follows may not give you a specific answer to that question, but it may provide a basis for better understanding. Energy from the sun, from hydraulic sources and from combustion has been available to man from prehistoric times, for thousands of years, but the most sophisticated source of energy, the actual conversion of matter into energy by man, has been developed entirely within the last one-third century, since the discovery of fission in 1939, and the application to generation of electric power has all been done within a generation or less. The pressure of military needs during and after the second world war was largely responsible for the speed of initial development, by funding and focussing the effort needed to develop the basic technology, and in particular materials. The U.S. defence program yielded, for example, the large-scale isotope separation processes for fissile U'35 and for heavy water. The nuclear submarine program yielded zircaloy, a key structural material for the core of the Canadian Candu type reactor."

Jan 1, 1972

By S. F. Dudka, T. Dang, M. L. Wong

Abstract - The Nui Phao W-F-Cu-Au-Bi deposit is located in one of the poorest regions of northern Vietnam. The deposit is currently undergoing a pre-feasibility study by Tiberon Minerals Ltd., with a view to developing what would be the largest WO3 mine and one of the five largest fluorite mines in the world. The project is being planned in close compliance with World Bank and national guidelines for environmental and social protection. Development of the mine is anticipated to bring the following benefits: remediation of serious pre-existing environmental conditions (natural and anthropogenic heavy metal contamination and acid rock drainage); provision of employment and training, and thereby wealth, to local communities; significant tax and royalty payments to government, which will be reinvested as social spending; and development of municipal and industrial infrastructure to build sustainable post-mining communities. The role of governments at all levels is critical in guiding and facilitating this process. This paper was written prior to development of the mine, and relays the intentions of the developers. Future studies will be needed to evaluate the degree of attainment of sustainable development objectives, both during mine operation and after closure.

Jan 1, 2003

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By Y. Qi

A cell-level nonlinear dynamic model of solid oxide fuel cell (SOFC) based on physical diffusion principles is built in this note. It demonstrates that reactant diffusion processes from gas flow bulks to triple phase boundaries (tpbs) play an important role in the dynamic behaviors of SOFC. The simulation shows that under certain condition, the effect of the double layer capacitance may be neglected. The phenomenon of slow rise of voltage in current interrupt experiment may be explained by the dynamic behaviors of partial pressures in the vicinity immediately above tpbs.

Jan 1, 2005

By J. G. Whellock, R. J. Phillips, J. W. Matousek, P. J. Marcantonio

"Stillwater Mining Company (SMC), a partnership of Chevron Resources and Manville Corporation, produces a copper-nickel, platinum-palladium flotation concentrate at its Nye, Montana mine. The concentrate is then toll processed in Europe. Recognizing the economic advantage of treating the concentrates at the mine site and of retaining this strategic resource in the United States, the Company commissioned Tolltreck International Limited and International Process Research Corporation to conduct pilot scale smelting tests with a flowsheet that would maximize metal recoveries while satisfying the environmental requirements of operations at Stillwater.Primary smelting was conducted in a single phase, 50 k W, submerged-arc, electric furnace. Refining the product mattes to copper-nickel ""white-metal""; containing approximately 2% iron, was accomplished in a Tolltreck, IV-litre, top blown rotary converter. Over-all platinum and palladium recoveries were approximately 99%; copper and nickel recoveries averaged 94%. INTRODUCTION(l-4)Stillwater Mining Company (SMC) a partnership of Chevron Resources and Manville, operates a copper-nickel, platinum palladium mine and concentrator at Nye, Montana, located in the valley of the Stillwater River, approximately, 100 km southwest of Billings. It is North America's only primary producer of these precious metals. The Stillwater area was mined for chrome ore during World War U and the Korean War, but it was not until 1961 that attention was drawn to the similarities between the Stillwater Complex and the Bushveld Complex of South Africa with its deposits of platinum group metals.A concentrated search for platinum was begun by Manville Corporation in 1967. Its presence, together with palladium, in mineable quantities was confirmed in the period 1976-1978, and the first partnership to develop the deposits was formed by Manville and Chevron in 1979. Anaconda joined the group in 1983, and in 1985 its share was purchased by Lac Minerals. In 1988 the interests of Lac Minerals were purchased by Chevron and Manville.The decision to develop the mine and build a concentrator was made in 1986. Construction began in the fall of that year, and the first concentrate was produced six months later, in March 1987. Underground mining is done in a two-shift, five day- week operation. Since startup, the concentrator has operated on a 24 hour/day, 7 day/week schedule, treating an average of 635 tonnes of ore per day and producing approximately 10 tonnes of concentrate."

Jan 1, 1989

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015

By J. Sugai

Formability of extruded round AZ31 magnesium alloy tubes with different manganese concentrations was evaluated by performing bending tests and measuring strain along the length of the tubes during the bending process. It was found that an increase in the manganese content from 0.3 % to 0.7% did not exert any significant effect on the values of yield stress, elongation, or compression to fracture. However the hardness tended to increase and the UTS decreased. The compressive ductility was significantly lower than tensile ductility for all manganese concentrations. Consequently, the formability of tubes decreased, causing cracks in areas where compression strain occurred during bending. It was also found that a larger strain occurred in the latter half of the region along the length of tube between the clamp-end and the tube-positioning block. Within this region, alloy tubes with higher manganese concentrations, 0.5 and 0.7 %, there was a clear strain peak within the strain profile, while for the 0.3 % Mn alloy, a more uniform strain profile was exhibited, indicating a more uniform deformation. This was confirmed by microstructural analysis of the specimens.

Jan 1, 2006

By Robert G. Boutilier

So far, most social performance monitoring systems have not gone beyond listing the impacts on various stakeholders. Executives have had to rely on intuition to devise interventions that would improve the impacts. This paper describes a survey process, known as the Stakeholder 360 (S360), which eliminates much of the guesswork. The paper reviews key studies showing that raising the levels of communication, trust, and common vision among stakeholders leads to the acquisition of the resources needed to improve the socio-economic situation. Therefore, the Stakeholder 360 measures the levels of these three factors in the relationships between a company and its stakeholders, and among the stakeholders themselves. In a validation study at a gold mine in rural Papua New Guinea, the S360 produced a socio-political ?roadmap? that showed management and stakeholders alike which relationships need more communication, trust, or common goals/vision. Management used the findings to create alliances that helped the government move forward on a regulatory regime for the mine closure. The community used the findings to focus its planning for life after the closure. An S360 survey conducted six months later revealed a decline in dependence on the mine and an overall increase in levels of mutual understanding.

May 1, 2002

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

The Beloziminskoe deposit in Siberia is a large, potentially productive deposit of rare metals contained in ochreous apatite pyrochlore ores formed by weathering of a carbonatite. The ores are composed of pyrochlore, columbitized pyrochlore, monazite, apatite, magnetite, ferric and manganese hydroxide, titanic iron ore, zircon, hydromica, quartz, feldspar, and carbonates. A gravity-flotation enrichment flowsheet with application of cationic and anionic collectors has been developed. This flowsheet allows for obtaining a pyrochlore concentrate containing 44.3% Nb2O5 and 1.89% P2O5 with recovery of 55.83% Nb2O5 as well as an apatite concentrate containing 39.2% P2O5 and 1.05% TR2O3 with recovery of 62% P2O5 and 43.23% TR2O3 from ores containing 0.92% Nb2O5, 16.9% P2O5 and 0.6% TR2O3. Rare-earth concentrate containing 40% TR2O3 with recovery of approximately 10% TR2O3 was obtained at the same time. Major losses of valuable elements are related to slimes, which make up more than 50% of the ground ore. The niobium concentrate does not meet the phosphorus and radionuclide concentrations needed for the production of ferro-niobium. Acid leaching and sulfatization provided a high level of phosphorous and radionuclide removal. Conditions include hydrochloric acid pre-leaching at 75- 80°C with an 18% HCl solution for four hours and low-temperature sulfatization of acid-leached concentrate at 160-180°C for one hour followed by water leaching of the residue. The apatite concentrate could potentially be processed using nitric acid leaching. This technology is based on decomposition of apatite concentrate with 55-57% strength nitric acid with transfer of rare-earth metals into solution in the form of ammonium phosphate. This technology recovers a rare-earth concentrate containing 95% TR2O3 with extraction of 86%, and highly concentrated polynutrient fertilizer (ammophos) with phosphorus extraction of 95%. The completed research shows how complex multicomponent ores of residual soil may be processed for the extraction of niobium, phosphorus, and rare-earth products.

Jan 1, 2016

By Kevin Ross

Feasibility Study Team Processing / Engineering?Hatch, Vancouver Mining / Reserves?Australian Mine Consultants, Brisbane Geology / Resources?Roscoe Postle Associates, Vancouver Environmental / Permitting?Rescan, Vancouver Tailings BGC, Kamloops Probable Mine Components Mining tending towards caving methods Underground mine accessed by shaft /conveyor & decline Processing plant producing copper concentrate containing gold Concentrate trucked to rail head for export Non saturated tailings disposal

May 1, 2006

By A. Probst, N. Moores, J. A. Finch

"In 1994 McGill and INCO (Sudbury operation) initiated transfer of technology originally developed to detect level in flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud-line and solids load. The probe consisted in a vertical tube with 32 equally-spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth (so-called conductivity profile) from which the mud line and % solids could be inferred. The probe was installed in October 1994 and has been successfully detecting profiles since then. This communication includes a description of incidents and experiences during this technology transfer process including: probe installation and start-up; software modifications to accommodate operating conditions and operators' needs; calibration procedures to adjust to changes in performance as a consequence of long term use; and preliminary observations on the last stage, still in progress, signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.IntroductionThickening is one of the basic unit operations in mineral processing and hydrometallurgy used to separate suspended solid particles from a solid-liquid dispersion by gravity settling. As the dispersion enters the thickener, the solids settle and clarified water overflows the top. A thickener, which may be continuous or batch, is basically a large vertical cylindrical tank provided with devices to feed the dispersion and to remove the settled solids. The tank provides residence time for the particles to settle. The dispersion enters the thickener through the feedwell whose function is to dissipate the momentum of the feed stream and to create relatively quiescent conditions around the entering point. Rotating rake arms move the settled solids towards the discharge point located at the bottom centre of the tank.There are normally three distinct zones in a thickener: a top layer of clear water, a middle layer called a sedimenting zone in which particles are settling, and a bottom layer called a compression zone in which particles are pressed together as a consequence of the weight of accumulated particles. Proper operation of a thickener requires two simultaneous conditions: no solids in the water overflowing the top and the target solids content in the underflow pulp. To achieve these conditions is difficult because sensors for detecting the sediment line (interface between clear water and sedimenting zone) and the solids content in the compression zone are not commercially available."

Jan 1, 1998

By . A. C. Atenas

Control of arsenic in the Potrerillos' Refinery electrolyte has been obtained by withdrawing a bleed stream of circulating electrolyte and ensuring the ratio of [O]/[As] in the cast anodes is maintained between 0.9 and 1.0. In order to achieve this control the anode oxygen must be adjusted, depending on the arsenic level in the cast anodes. It has been necessary to modify the time of the reduction step in the anode furnace refining process. Control of this ratio has permitted electro refining of anodes with high levels of arsenic, up to 3000 ppm, while minimizing the volume of electrolyte that must be removed for impurity control so as not to affect the copper concentration in the electrolyte. However this control strategy is not useful when the arsenic concentration in the cast anode is too high, because it is limited by the maximum oxygen concentration allowable for a good quality anodic. Costs have been reduced in anode furnace refining because it is no longer necessary to use alkaline flux injection to remove the arsenic in cast anodes.

Jan 1, 2007

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However, high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives. IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million. Canada is second in world production of asbestos behind the U.S.S.R. The milling of asbestos ore has been done primarily by a series of steps involving crushing, dry-grinding and aspiration using large quantities of air to release the fibres. Contrast this process to those practiced in the purification of virtually every other mineral. Ores other than asbestos are crushed and milled using an aqueous slurry in rod, ball or pebble mills. The finely ground mineral, still as a slurry, undergoes beneficiation by froth flotation, heavy media separation, hydrocyclones or any of the other aqueous techniques currently employed in mineral processing.One of the driving forces behind the use of air instead of water as a means of separating asbestos is the nature of the aqueous asbestos slurry. While most slurries of minerals contain as much as 80070 solids and can still be pumped and transported, asbestos slurries become highly viscous with as little as 10070 solids. These high viscosities reduce the pumpability of the slurry and create severe handling problems. Mills become prohibitively large and uneconomical due to having to handle slurries containing only 10% rock and 90% water.Health-related issues have affected the use of asbestos in many countries. In Canada, the asbestos-producing provinces have introduced stricter occupational legislation to improve safety in the workplace. This primarily means strict control minimizing release of air-borne asbestos fibres . Quebec and Ontario have set limitations of airborne asbestos at 2 (2) and 1(3) fibre per cubic centimetre of air. With present milling technology, maintaining these low levels in the workplace requires constant vigilance."

Jan 1, 1988

By A. Siegmund, F. Mucciardi, Z. Yuan, B. Bulnes

With conventional heat pipe science as the starting point, a new heat transfer technology --- termed Thermopump technology, has been developed at McGill University and is now being tested at a number of industrial operations. This technology is of particular importance for transferring energy in high temperature / high heat flux environments where solutions based on current techniques are not available. One important application for this technology is in the metals recycling area wherein this technology has been used to make a waterless, non-consumable, high efficiency Thermopump oxygen lance. The viability and efficiency of this oxygen lance have been demonstrated by preliminary plant trials in a reverb furnace for the recycling of lead-acid batteries at the RSR Corporation. Full-scale commercial trials of the Thermopump (TP) oxygen lance have been carried out at the RSR Corporation. The results from these tests will be presented. In addition, some applications of the Thermopump technology for other metal recycling processes will also be discussed in this paper.

Jan 1, 2004

By C. P. Verschuren, P. W. Kingston, W. F. Caley

"In recent years, there has been rapid growth in the use of natural stone building and construct ion products. The largest growing markets are for pre-fabricated natural stone panels for interior and exterior wall facing and flooring. This increased demand is attributed to advanced quarrying and processing technologies, renewed appreciation for the aesthetic appeal of natural stone, and to the superior durability of natural stone when compared to glass, steel, and concrete. Geologically, plutonic rocks, and to a lesser extent marble and limestone/dolostone, are used extensively for these applications. This paper details the economic structure of the dimension stone industry, describes the necessary characteristics of a stone quarry, and outlines the geological criteria which favour an economic quarry.INTRODUCTIONThe world building stone industry has remained relatively stable over the last 5 to 6 years. In contrast, the North American stone industry has experienced substantial growth during that period. The increased use of commercial granite is primarily responsible for this growth, where use as exterior wall veneer for commercial, industrial, and institutional buildings represents the largest and fastest growing market.This increased usage in the construction industry has been sparked by the application of new technologies in quarrying, processing and installation , ma king natural stone more competitive with man-made materials which are energy intensive to produce, and have risen dramatically in price. The development of safer, time-saving stone installation techniques has also appealed to the liability-conscience construction industry. Finally, there is a trend by designers and architects toward utilizing long-la sting weather-resistant building materials, and a renewed appreciation of the aesthetic appeal of natural stone. The other large user of granite is the monument industry of North America which, although it has decreased slightly in recent years, still consumes approximately 40% of all commercial granite produced. The local use of commercial marble has remained relatively stable, and North America still relies heavily on European sources and suppliers. There has been some concern over the use of marble for exterior applications in areas subject to acid rain, and in colder climates where the marble ma y be vulnerable to freeze thaw cycles. Despite these concerns, the greatest problem is not with the structural breakdown of marble but the inability of some marbles to retain their polished finishes in the se environments. As a result, there has been an increase in the use of granite at the expense of marble for exterior applications. Finally, commercial marble is used extensively for interior flooring, wall s, counter tops, furniture, sculptures, and stairway components"

Jan 1, 1989