Search Documents

By J. Bouchard, M. Levesque, D. Georges-Filteau, P. Radziszewski, G. LeBlanc

"Grinding mills are infamous for their extremely low energy efficiency. This paper reports the results of an investigation that characterized energy outputs in industrial grinding mill circuits. It identifies and discusses the potential for recovering energy from grinding circuits. Agnico-Eagle Goldex Division, Mine Canadian Malartic, and New Gold New Afton Mine participated in the study by providing operating data for three semi-autogenous grinding mills and four ball mills. Results showed that on average, 79% of the supplied electrical energy was converted to heat absorbed by the slurry, 8% was lost through the drive system, and approximately 2% was transmitted to the ambient air. Only 9% of the input energy was actually used for grinding. The remaining 91%—wasted as heat—could potentially be recovered using suitable technologies or integrated energy management systems. This topic remains to be further investigated. ¦ KEYWORDS Comminution processes, Energy recovery potential, Grinding mills RÉSUMÉ Les broyeurs sont tristement célèbres pour leur rendement énergétique médiocre. Cet article présente les résultats d’une étude qui caractérise les rendements énergétiques des circuits industriels de broyage et examine les possibilités de récupération d’énergie dans les circuits de broyage. La mine Goldex d’Agnico Eagle, Mine Canadian Malartic et la mine New Afton de New Gold ont participé à l’étude en fournissant des données de fonctionnement pour trois broyeurs semi-autogènes et quatre broyeurs à boulets. Les résultats montrent qu’en moyenne 79 % de l’énergie électrique fournie sont convertis en chaleur absorbée par la pulpe, 8 % sont perdus dans le système d’entraînement et environ 2 % sont dispersés dans l’air ambiant. Seuls 9 % de l’énergie primaire sont, de fait, utilisés pour le broyage ; les 91 % restants (perdus sous forme de chaleur) peuvent potentiellement être récupérés à l’aide de technologies adaptées ou intégrées dans des systèmes de gestion de l’énergie. Cette question demeure toutefois ouverte. ¦ MOTS CLÉS broyeurs, potentiel de récupération de l’énergie, procédés de comminution INTRODUCTION Grinding is largely recognized as a very inefficient process; energy efficiency estimates range from < 1 to 2% (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002, 2004) when comparing the input energy to that required for generating new mineral surfaces. Criticizing an “ill definition of the reference for the output energy,” Fuerstenau and Abouzeid (2002) proposed a “more meaningful baseline” would be “the energy for producing new surface area by the ¬mens.” Based on this reference, they concluded that “the ball mill is reasonably efficient energetically,” exhibiting an efficiency of approximately 15% for quartz."

Jan 1, 2019

By Leslie McHattie, Sadek E. EI-Alfy

"The Maintenance Engineering Department at Carol Mining and Concentrating is currently in the process of introducing reliability concepts such as failure analysis, rework elimination, predictive maintenance, computerized maintenance history analysis, etc. to improve the over-all maintenance function in the mine and concentratormaintenance areas. Some current initiatives include:• Implementation ofan infrared thermographic scanning program.• Ultrasonic inspection of shafts for all critical equipment in the mine and concentrator areas.• Non-destructive testing of all major welds done by maintenance personnel.• Development of an effective vibration monitoring and analysis program for the production equipment in the mine (shovels, drills, haulage trucks, locomotives).• Failure analysis performed by maintenance engineers to identify the root cause of component failures on critical production equipment.• Computerized breakdown analysis to identify the recurring component failures which contribute significantly to high maintenance costs and production loss.• Implementation of a computerized maintenance management information system.This paper will outline the planned implementation ofthese initiatives, and others, and will also cover the status and results obtained to date."

Jan 1, 1992

By Ahmad Hemami

A working code is developed to simulate the forces that are involved in the process of penetration of a bucket into bulk media during loading and excavation. The result of this work can be integrated with the simulation software that many manufacturers of heavy earthmoving machines introduce for training purposes. The simulator programs for machines such as backhoes, loaders, LHDs and the like, used for operator training, are usually only based on the kinematics of the machine. As a result, there is no indication of the effect of the medium when the cutting tool of such a machine touches the excavation material. This is like moving the machine in the air. Feeling the resistance force of medium to cutting by a bucket or blade during loading and excavation is more realistic, both mentally (by vision) and physically (feeling resistance in pedals and levers). The results from force simulation can be used by feedback in creating simulated resistance in these training gears, similar to what is done in flight simulators for aircrafts. In addition to serving for the above purpose, the results of this work can be used as a tool for examination and verification of the effect of a control policy for automation of loading and excavation of bulk media. So far no commercial product has been introduced that has such a capability, despite some extensive research on the subject.

Aug 1, 2013

By D. Brossman

"The virtue of spray drying is that it is a drying method, and so far the only one by which it is possible in one operation to divide a mineral concentrate into its basic primary particles.,In so doing, each particle gets the same treatment and the result is a dry concentrate more homogeneous than any other known concentrate drying process. This is particularly good for a flash furnace requiring a bone dry finely divided feed. The spray dryer also features a very short residence time and due to the very quick operation the solids are kept cool thus preventing any risk of fire or explosions on these pyrophoric materials.There are many spray dryers now in operation in the mining industry and one of the latest applications is in South Africa where a spray dryer is treating a copper-nickel platinum concentrate which is, after drying, fed toan electric arc furnace. Experience has shown that the concentrate should contain 4% moisture for the furnace, and this is achieved by drying the concentrate bone dry and then back-mixing with thickener underflow pulp to provide an extremely homogeneous feed to the smelter. As mentioned before, mixing with pulp would be more of an advantage because we would not be evaporating water which would have to be added again afterwards.One of the first spray dryers to go in was at Western Mining Corporation in Kambalda in Western Australia. (A series of slides was then shown)."

Jan 1, 1972

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By R. J. Chase, C. Davies

"The Merelani graphite-tanzanite deposit is located in northeast Tanzania, 14 kilometers south of Kilimajaro International Airport and in close proximity to the towns of Moshi and Arusha. The graphite mineralization is hosted by relatively undeformed linear Proterozoic metasedimentary gneisses, several of which have been subjected to hydrothermal alteration resulting in tanzanite mineralization. Exploration work comprised detailed geological mapping coupled with pit and trench channel sampling and a subsequent 1500 meters of diamond drilling. In addition, metallurgical tests have shown the graphite to be of unusually coarse flake size, crystallinity and high purity.Feasability studies have shown the economic viability of a major coarse flake graphite deposit with the measured resource to 50 meters in excess of 9 million tonnes assaying over 85 graphitic carbon. Production is due to start by the end of the first quarter of 1994 with the processing plant design capacity initially set at 15 000 tonnes per annum.In addition to graphite production, tanzanite will be produced through selective mining within the graphite open pit in the upper horizon and from underground workings within the lower horizon.The Merelani graphite-tanzanite deposit will be the first major orebody to be exploited through means of private funding since Tanzania gained independence"

Jan 1, 1994

By C. J. Li, J. L. Feng

In the present study we focuses on developing the poroelasticity model that deals with adsorptioninduced permeability change mostly occurred in porous media constituted several phases such as coal. The underlying pressure induced by adsorption is obtained by Virial expansion form, which is substantially founded on statistical physics. The corresponding thermodynamic pressure applying on the pore surface is then used to detail the pore pressure and further to evaluate the macroscopic volumetric strain and the porosity. In the process of physical adsorption, the adsorbed phase is in thermodynamic equilibrium with the gas phase regardless of pore size, and the corresponding chemical potentials are all equal. The relationship between surface strain and volumetric strain is derived under infinitesimal deformation conditions to gain an explicit formulation of pore surface area with respect to volumetric strain and porosity. After the formulation of surface stress modified by the Langmuir isothermal adsorption is derived, the differential micromechanical constitutive equations of porous media are obtained. By supposing that the ratio of current permeability to initial is equal to the cubic ratio of current porosity to initial porosity, the differential equations for permeability change is consequently derived. The numerical simulations by the present model for permeability change of coal induced by adsorption of CO2 and CH4, respectively, are presented under confined stress conditions. The predictions from the model are good in agreement with the experimental data of sorption-induced permeability change of coals in the literature.

Jan 1, 2015

By Aimee Williamson

Bio-mining is a cost-effective, energy efficient and potentially environmentally protective method of exploiting a variety of ore deposits, from high-grade base metal deposits of nickel to lower-grade uranium deposits such as are found in the uraniferous quartz-pebble conglomerate beds of the Quirke Syncline, Elliot Lake, Ontario, using bacterial metabolic processes are used to enhance the solubilization of the metal(s) of interest. The cost effectiveness of bio-mining in Elliot Lake depends on the bacterially-influenced dissolution metals of economic importance, as well as on the ability to suppress microbiological activity following the release to solution of the economically important elements. This poster provides an overview of elemental recovery results and release kinetics for more than 50 elements. The data is obtained using a combination of advanced spectroscopic tools (ICPAES and ICP-MS) to analyze solutions obtained from a series of environmentally controlled biologically mediated uranium ore extraction experiments. The focus will be on rare earth elements, potential environmentally toxic elements, and metals of economic importance. Furthermore, the importance of these findings will be put into an economic and geologic context for the re-development of the mining industry of the Elliot Lake Camp.

Aug 1, 2010

"Adopted in 2003, theses guidelines are intended to assist the Qualified Person(s) in the planning, supervision, preparation and reporting of mineral resources and mineral reserve estimates. The report is divided into two broad sections “General Guidelines” appropriate for most metals and “Guidelines Specific to Particular Commodities” for potash, industrial minerals, uranium and coal. “These guidelines are reference in the Companion Policy of NI 43-101 with a statement that a qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow them.”Executive SummaryThe following is a summary, in table format, of the main elements of the Estimation Best Practice Committee's report ""Estimation of Mineral Resource and Mineral Reserve Best Practice Guidelines"". While the summary table is provided for convenience, the Committee recommends that the report be read in its entirety and the table summary not be used as a stand alone document. These guidelines are not intended to be either prescriptive or exhaustive. They do not preclude innovation. Preamble: These guidelines have been prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) led Estimation Best Practices Committee. They are intended to assist the Qualified Person(s) (QP) in the planning, supervision, preparation and reporting of Mineral Resource and Mineral Reserve (MRMR) estimates. All MRMR estimation work from which public reporting will ensue must be designed and carried out under the direction of a QP in accordance with National Instrument 43-101 (NI 43-101) and related forms. A QP is defined in NI 43-101 as ""an individual who is an engineer or geoscientist with at least five (5) years of experience in mineral exploration, mine development, mine operation, project assessment or any combination of these; has experience relevant to the subject matter of the mineral project and technical report; and is a member in good standing of a professional association"". Disclosure of MRMR estimates is to be made in accordance with industry standard definitions approved by the CIM (the CIM Standards adopted by the CIM Council in August 2002) which have been incorporated by reference into NI 43-101."

Jan 1, 2003

By B. Zhu, W. E. Lee, N. Li

Al powder is used extensively as an antioxidant in carbon-containing bricks, but it cannot be used directly in water-based carbon-containing castables due to its hydration tendency. To overcome this problem, in this work, SiO2-PVA (polyvinyl alcohol) inorganic-organic hybrid coatings have been prepared via sol-gel processing, and used to coat Al powder. The hydration behaviour of uncoated and coated Al powders has been investigated in water at 60 or 100°C for 36h by examining phase and microstructural changes. While significant hydration is detected in uncoated Al powder, no obvious hydration is detected in coated Al powder, indicating that its hydration resistance has been greatly improved. Oxidation resistance of graphite coexisting with uncoated or coated Al powder was also investigated in air at 1250°C for 1.5h. The oxidation ratio of graphite coexisting with coated Al powder was similar to that of graphite coexisting with uncoated Al powder, indicating that both powders showed similar antioxidising behaviour. This, along with the much improved hydration resistance, makes the coated Al powder a potential antioxidant in carbon-containing castables systems.

Jan 1, 2004

By R. Heikkilä

As a part of a large research and development program in Finland, a system calibration for an UAV measurement method having practical experiments in a Jorvas Railway Yard design and construction project. The Railway yard construction are was measured using an UAV measurement device by Smartplanes (Smartone) and using some reference points measured by a GNSS device. The measured data was cleaned, combined and adjusted through Least Squares Optimization using the software developed by a Finnish company Pieneering Oy. As references, two different laser scans as well as total station surveys were used. For applicability evaluation, the accuracy of measurement, the reliability of measurement, and the economy of measurement were used. Based on the comparisons, the achieved precision of the UAV measurement was high, instead the accuracy of measurement was not sufficient in this case. The principle of this photogrammetric measurement includes a lot of redundant observations making it possible to achieve a high level of reliability. The economy in this Railway Yard Design project was not able to achieve.

Aug 1, 2013

By Rob Scott

Making a difference with Zinc & Health Two billion people do not get enough zinc in their diets. Every year 450,000 children die from complications arising from zinc deficiency Our Zinc Alliance For Child Health partnership with CIDA and Micronutrient Initiative, our involvement with UNICEF through the IZA and our partnership with BASF are gaining wide recognition. Sustainability at Teck ? Integrating into our Core Business Strategy Our strategy Long term goals Our approach Managing risks and finding opportunities Our progress Early reports Moving Forward Metrics and indicators

May 1, 2013

By M. Mahdi, L. So, A. MacMillan, D. Metcalfe, J. Woloshyn, D. Sauter, N. Uys, JP. Janse van Rensburg

For city smelters, with limited real estate, efficient slag cleaning furnaces followed by water granulation to produce an iron silicate product is the preferred process approach. Water granulation, however, consumes large volumes of water and requires high maintenance due to abrasive slag/water slurries. Air granulation offers an alternative to water granulation, which eliminates water use and has low maintenance requirements. Although full-scale operation has not been implemented for copper slags, full-scale operation for platinum group metal (PGM) converter slag has been implemented. A review of full-scale air granulation performance for PGM converter slag is provided. Based on PGM converter slag granulation performance, parallels to copper slag granulation are drawn and full-scale operation for copper slag is modelled using computational fluid dynamics (CFD). INTRODUCTION Typical slag management practices in the copper industry include dumping, slow air cooling, and water granulation, as shown in Figure 1. Dumping is the most commonly used slag handling method for most metal production plants, but presents challenges including the requirement for a large slag pit, requirement for expensive/high-maintenance “hot” mobile equipment, risks associated with transportation of molten slag, and no value recovery from slag as a sellable by-product or from slag as a source of heat.

Jan 1, 2019

By V. Chatain

The environmental assessment of historical mining sites contaminated with various inorganic species, as also the determination of remediation targets require a better knowledge of pollutant-bearing phases. The objective of this paper was to investigate the operational fractionation of arsenic (As) in an As contaminated (ca. 3 wt%) soil collected from a gold mining site in France, where mining activities and smelting processes of gold ores took place until 2004. Single and sequential chemical extraction procedures were performed to evaluate the potential mobility of As according to the fractions to which it was associated in the contaminated soil, and also the part of As sorbed onto soil particles. These procedures used provided information on the nature of As fixation processes in the mining soil studied. Results showed that As appeared mainly sorbed (ca. 72%) with iron on the soil particles, in particular amorphous iron oxyhydroxides. These results confirmed a potential risk of arsenic mobilization under acidic and/or reducing conditions, which frequently occur in mining environment. This research evidenced the importance of the knowledge of As-bearing phases to better predict the mobility of this pollutant and in turn improve the management of As contaminated sites.

Aug 1, 2013

By P. Reyes

The Codelco Chile El Teniente Division Caletones Smelter has an objective to smelt 1,250,000 tonnes per year of copper concentrate. This is a great challenge for the smelter facilities and particularly for the acid plants. The analysis ensuring that there are no obstacles to achieve the production capacity was of great importance. Therefore a series of activities were undertaken as well as studies dedicated to reach the target. This paper presents work focused on a fluid dynamic study, translated in an operation methodology of integrated handling of the smelting and converting gases with the objective to optimize the gas flow and S02 concentration. The optimization should be done employing the current installations, equipment and instrumentation and/or minor modifications. In the first part of the work the condition of the instrumentation involved in the gas handling was checked, improvements determined and the corresponding corrective actions were carried out. The proposed operation method consists of operation of the Cleaning Gas Plant 2 (TC&apos; s gases) and operation of Gas Cleaning Plant 1 (the remaining gas plus the gases from CPS). The implementation of the operation method involves the modification of the valve of the gas into the duct to plant 1 from On to Off to modulate flow. After modification a three days test was carried out. To evaluate the tests, a "Sulphur Capture" indicator was used. During the test the behaviour of the effluent treatment plants was closely examined. No problems or unusual operating conditions were observed. The reduced flow of gas to Gas Cleaning Plant No. 1 permitted the start up of the 2nd test day treating most of the gas received by Gas Cleaning Plant No. 2. The operation was carried out with the limitation not to increase the effluent pond level, which was maintained constant.

Jan 1, 2007

By C. Diaz, S. W. Marcuson, K. I. Burgess

Deep roasting in fluid bed roasters is the first unit operation in Inco&apos;s "roast-reduction smelting" process for the treatment of nickel sulphide concentrates. The roaster product, a low sulphur calcine, is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte which is then converted to low (<1%) iron matte in Peirce-Smith converters. Due to the deep roasting, a minimal amount of sulphur dioxide is evolved in the smelting and converting stages. Sulphur is eliminated from the concentrate almost exclusively in the roasters in a single, continuous, strong, gas stream suitable for treatment in an acid plant. This paper discusses the commercial scale testing of deep fluid bed roasting of nickel concentrate at Inco&apos;s Thompson Smelter as part of two commercial scale campaigns on roast reduction smelting conducted in 1981-1982. Slurry feeding, practised during the second campaign, permitted excellent control of the air/concentrate ratio in the roaster and, in turn, good control of sulphur elimination (about 80% of input). Smooth autogenous operation with high oxygen efficiencies (about 95%) was promoted by operating at bed temperatures of830°C to 850°C with calcine recycle. High throughputs and the desired metallurgy were achieved. The extensive testwork conducted during the two experimental RRS campaigns demonstrated thot deep fluid bed roasting of nickel concentrate at high oxygen efficiency is a technically viable operation.

Jan 1, 1994

By J. B. De Hart

In the September issue of the Bulletin, 1923, there is a paper by J. A. H. Church on "The Spontaneous Combustion of Coal in Mines", which is more or less a general discussion of the subject. Mr. Church gives a list of mine fires which have occurred in Alberta. Of the total of thirteen fires, six are attributed to spontaneous combustion. Of these six fires, it will be noted that five are in thick pitching seams. These fires occurred in the following mines during the years shown, at Frank in 1909; at Lovett in 1916; at Cadomin in 1920; at Yellowhead in 1922, and at Cadomin in 1923. Every one of these fires has occurred, as Mr. Church points out, in a seam of over 12 feet in thickness, and furthermore not one of these fires has been extinguished, although in every case large sums of money were expended and considerable risks . taken in fire fighting. Now it is quite evident from these facts that mines working seams of this nature are faced with a very grave danger and it behooves us to study the matter and endeavor to arrive at some practical method of preventing the loss of our coal mines from this cause.

Jan 1, 1924

By R. J. McCarthy

In-pit Crushing and Conveying (IPCC) is increasingly being considered by mining companies as a means to reduce their dependence on trucks and thus, fuel, tires, labour, etc. There is potential for great savings in operating costs which ultimately can mean better economics for a mining project. Vale has considered the application of IPCC at its Moatize coal project in Mozambique. Up to three studies have been conducted with the latest, at a pre-feasibility level, showing some promise. This paper explores the mine planning and IPCC engineering elements required in an IPCC study, their application to the Moatize project, and the drivers which most impact the viability of IPCC at Moatize.

Aug 1, 2013

By W. J. Kempson

In recent years, substantial progress has been made with respect to the definition and control of the primary energy requirements in underground mines. Little has, however been done to develop a more detailed understanding of how to limit the various pressure losses which are intrinsic to shaft systems. This is in spite of the fact that more than half of the pressures generated by the ventilation fans in deep level mines are dissipated as pressure losses within the shaft system. This paper presents research which has been completed to optimise the pressure losses which occur in shaft systems as a result of the ventilation air flowing through them. In this regard, the response of various shafts to the ventilation air flowing through them was measured. These results were evaluated against the current theory for the calculation of shaft pressure losses. Finally the results of the measurements and calculations were used to calibrate a Computational Fluid Dynamics model of the shaft systems. This model was then iterated to allow meaningful conclusions as to the specific make up of the shaft equipment which contributes the most to pressure losses in shaft The results of the above analysis demonstrated that the current theory used for the evaluation of these pressure losses is deficient. The paper discusses these conclusions and the specific ramifications of the analysis. Finally, the understandings gained with regards to the above research are applied to the design and layout of equipment in mine shafts. In this regard, the shape and orientation of the shaft steelwork is evaluated and it specific interaction with the piping and conveyance is evaluated. Coming out of this evaluation are specific recommendations for the design of future shaft systems. These recommendations are based on the above models and offer specific savings on the lifetime operating costs of shaft systems.

Aug 1, 2013

By Patty Simpson, Sarah Benson

In an effort to improve consistency across the nuclear industry, over the past 10 years the Canadian Standards Association has developed a series of standards related to environmental management at Class 1 nuclear facilities and uranium mines and mills. Canadian uranium mines have been required by the Canadian Nuclear Safety Commission to align their existing monitoring programs with these standards. Orano’s McClean Lake Operation’s monitoring program, which was originally presented in the Environmental Impact Statement in 1991, has evolved through regulatory change, new scientific understanding, additional projects, and experience into a comprehensive set of monitoring requirements for effluent, groundwater, air emissions, and the receiving environment. The exercise of aligning the existing practices with the standards provided an opportunity to review and rationalize the entire program. To document the process the original “Environmental Monitoring Program Design Document” was restructured and developed as both a repository for historical information and monitoring rationalization, and also to be a living document describing on-going studies and supplementary work that are outside of the regular environmental monitoring program and may justify future changes to the program.

Jan 1, 2020