Search Documents

By M. Dosoudil

"Continuous pressure filtration is a modern process for the mechanical dewatering of flotation concentrates of coal and similar coal slurries. This method will give a lower moisture content than classical vacuum filtration, the improvement lying in the range 5% to 15%. Eighteen coal slurries have been examined in this survey. They are representative of a wide spectrum of filtered slurries. IntroductionDuring the last five years, a number of coal slurries have been tested either in the laboratory or with a pilot plant. The test pressure ranged from one to six bar. The results have been evaluated by mean s of a computer. Determination of the filter capacity and the resulting moisture content and energy consumption has been made with respect to the continuous pressure filter, Amafilter construction-type KDF (Fig. I) . Standard sizes of these filters are 60 m2, 90 m2 and 120 m2.The continuous pressure filter is a horizontal filter with a level tank. Six filter axles are mounted on a rotating main shaft, each with a particular number of elements attached. The elements rotate on their axes and move along a circular trajectory. Periodically the elements submerge into and emerge out of the slurry. A constant air pressure is maintained above the suspension, thus providing the pressure gradient necessary for filtration. The filtrate together with the dewatering air flows through the elements into the hollow axle and out of the filter."

Jan 1, 1987

"In the first half of 1990, Cambior earned $1104 million, or $0.37 per share, on revenues of$66.4 million. The company's strong cash position, attained late in 1989 and in the beginning of1990 through the exercise of warrants, put working capital at $83.8 million as of June 30, 1990. Long-term debt was reduced by over $10 million during the weak gold market, leaving the company with a debt to equity ratio of only 0.03. Production for the six first months of 1990 was 107 720 oz. Au, an increaseof24% over the corresponding period in 1989.Financial Profile/Results and Corporate Financial StrategiesTotal revenue for the 1989 fiscal year was $116,883,000 compared to $109,848,000 for 1988. The 1989 results achieved despite a lower average gold price, resulted from a higher level of commercial gold production and a 115% increase in investment income over 1988. Investment income rose to $3,568,000 in 1989 due to higher levels of cash assets.Cambior's mine operating costs increased 19% to $68,561,000 in 1989 from $57,472,000 in 1988. This increase resulted from rising operating costs at the Doyon Mine ($250/oz to $274/oz) due to the shift from open pit to underground operations, as well as from the start -up of three new mines with relatively higher costs. These costs have reached a stable level that should be maintained for the next few years.In 1989, net exploration expenses were $6,838,000, down 31070 from 1988, partially due to the Canadian tax reforms introduced since 1987. Depreciation and depletion grew by $1,432,000 in 1989, reflecting a higher volume of commercial production from the Pierre Beauchemin, Lucien C. Beliveau and Chimo mines.Net earnings for 1989 amounted to $17,661,000 or $0.73 per share compared to $17,438,000 or $0.74 per share in 1988.Cambior has an exceptionally liquid and strong balance sheet. As at December 31, 1989, net working capital stood at $85.6 million, with a total assets base of $338.6 million. With a long-term debt (including gold loans) of $21.5 million and shareholders' equity of $277.2 million, Cambior has a debt to equity ratio of 8%. All but about $100,000 of long-term debt is in the form of gold loans.The total market value for Cambior's stock as at September 10, 1990, stands at $420million, based on recent stock market prices. Cambior's stock and warrants are traded on the Montreal and Toronto Stock Exchange."

Jan 1, 1990

By A. Vasebi, É. Poulin, A. Desbiens, D. Hodouin

Maximizing benefits generated by separation plants in the mineral processing industry is of prime importance. To achieve this goal, observers and controllers are both key tools playing a crucial role for economic optimization. Although these methods have been widely discussed in the literature and that numerous applications have been reported, coupling the different algorithms raises practical challenges. The economic function definition, the selection of the real-time optimization structure, the elaboration of observer and controller models, the controller development, and the tuning of stochastic and deterministic parameters strongly influence economic performances. The objective of the paper is to discuss the major difficulties related to the implementation of a real-time optimization system and highlight the benefits of linking data reconciliation and model predictive control for a simulated flotation plant. A systematic topdown approach is used to go through the main design phases and to comment on the different options available for the development of the optimization structure. An internal model predictive controller coupled with a stationary observer is applied for the direct optimization of a three-stage flotation plant simulator based on a phenomenological model. The results show performance improvements in terms of increased revenues brought by reduced grade variability and collector consumption. The discussion also proposes alternative avenues that could be taken to achieve comparable improvements. Finally, since the limited simulated case-study cannot provide a complete understanding of the benefits brought by a data reconciliation observer, recommendations for industrial applications, which are more complex, are provided to promote effective implementations.

Jan 1, 2016

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018

By S. M. Bulatovic, D. M. Wyslouzil

"This paper presents the results of a study of the effect of flowsheet configurations on metallurgical results and describes a general method for developing and optimizing flowsheets used in the treatment of massive sulphide ores. The flowsheet configuration can have a significant effect on recovery and selectivity between valuable minerals and gangue minerals. Placing of intermediate products within the flowsheet, positioning of various pretreatment units, such as conditioners or regrinding mills, and the ability of the flowsheet to cope with wide swings in the feed grade and composition are the major parameters that determine the optimum flowsheet configuration. The complexity of the flowsheet is largely a function of the ore itself and of the number of final, marketable products that have to be recovered from the ore. INTRODUCTIONTechnological ExpansionThe trend of past decades has been towards larger equipment and a better understanding of the chemistry of the flotation process. Despite appreciable progress in these areas little attention was given to the study of the actual configuration of the flowsheet, although the arrangement of the flotation equipment significantly affects the overall performance of the circuit."

Jan 1, 1989

By Hans D. Gougar

To meet an increasing demand for minerals, mining operations are moving to ever more remote regions. The lack of a local energy supply and infrastructure, coupled with social and regulatory demands for lowered environmental impact of mining operations, presents an opportunity for a seemingly unlikely competitor ? a nuclear power plant. The Modular Pebble Bed Reactor concept, currently in various stages of research and development around the world, offers a high degree of reliability and safety with minimal consequences for the local or global environment. The passive safety features of this design eliminate the need for the extensive active safety systems that add significantly to the cost of current water-cooled reactors. With the MPBR, as with all nuclear plants, there are no appreciable quantities of waste products released to the environment during normal operations. In contrast with conventional reactor designs, the MPBR would also remain radiologically safe even under the most severe abnormal circumstances. The key to the design is the fuel element. Enriched uranium microspheres are coated with various layers of pyrolytic carbons and silicon carbide to form a highly-temperature resistant particle that effectively retains all fission products. These particles are mixed with graphite and formed into 6 cm pebbles. A randomly packed vessel of such pebbles forms the reactor core through which helium is circulated as a coolant. Computer models and tests performed on actual pebble bed reactors confirm that fuel failure temperatures are not reached even during the most severe conceivable loss of coolant accident. The reactor drives a gas turbine cycle with resulting efficiencies as high as 48%, comparable to natural gas-fired units. The low price of uranium fuel and low maintenance requirements translates into competitive operating costs. However, high capital costs prevent the MPBR from competing with natural gas in most markets. In remote applications where no fossil supplies are readily available, the playing field is more level. This paper summarizes the features of two of the more promising candidates for remote applications and discusses the strengths of the MPBR from the perspectives of fuel supply and environmental impact.

May 1, 2002

By Chris Blain

"Abstract - Based upon an extensive database, this paper analyzes the record of modern mineral exploration success and establishes the 50-year trends in discovery. The record clearly shows that the overall discovery rate rose during the 1950s and 1960s, peaked in the 1980s, and fell during the 1980s and 1990s. By commodity and ore-type target, the pattern of discovery is not continuous. Typically, it is episodic as a series of waves with minor resurgence. The waves reflect the order of the so-called discovery booms, led by uranium, then nickel, and copper, polymetallic base metals and gold. With the possible exception of gold, the discovery booms appear to be independent of metal price, although favorable perceptions of the price outlook may well have initiated the boom or led resurgence. Although difficult to quantify, an emerging trend in modern discovery is the integration of several detection techniques into the search process. No doubt, this trend will continue as orebodies become more and more difficult to find. The record of the past two decades shows that greenfield discovery rates have progressively fallen even though the level of investment in exploration has risen to an all-time high. This trend reflects increasing discovery risk. Several factors are contributing to this trend. Perhaps the two most important are: (1) deteriorating economics as increasing real costs and decreasing real prices continue to raise the economic hurdles for minimum acceptable exploration targets, and (2) increasing exploration maturity in many search terrains, particularly those in the traditional regions of North America and Australasia. To succeed cost-effectively in this new environment of increasing discovery risk will require extraordinary creativity, innovation, and technical skill coupled with commercial discipline."

Jan 1, 2000

By C. J. Sullivan

It is of importance, in prospecting, to distinguish ores of magmatic origin from those derived by the meta-morphism and granitization of source rocks and from those accumulated in certain sedimentary facies. The magmatic ores, which are characterized by their occurrence along fault structures, may be associated with volcanic (including explosive) phenomena. Heat effects are local. The magmatic sequence is well de-fined: kimberlite, with diamond pipes; ijolite, with carbonatites; peridotite, with nickel deposits; norite, with nickel-copper deposits; and diabase-gabbro, with copper-zinc deposits. These deposits are characteristic of Precambrian shields, where a thick sialic crust may rest on basic to ultrabasic magma. The sequence is resumed in the Paleozoic terrains (in a broad sense), with monzonite porphyries and associated copper, copper-gold, and cop-per-lead-zinc deposits.

Jan 1, 1962

By C. A. Godden, T. N. Atkinson

Metallographic techniques developed from studies of corrosion films and electroplated coatings on aluminum alloys, are discussed. These methods, the result of work at the Naval Research Establishment, give extremely flat fields at the interface despite the large difference in hardness, in cases where electrolytic polishing could not be used. Techniques to overcome the similarity in refractive index of immersion oil, aluminum ox1d~, and mounting plastic are also considered, as are methods for improving visual and photographic contrast in areas of interest. A device for marking specimens is also de-scribed. ELE•CTROLYTIC polishing is inapplicable in the study of surface films on aluminum, whether corrosion films or electrodeposits. Mechanical procedures must there-fore be followed. Sample flatness and edge retention are of paramount importance. Special measures are required in the study of oxide films, because of the close proximity of the refractive indices of aluminum oxide, mounting plastic, and immersion oil.

Jan 1, 1962

By Robert E. McIvor

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency also has been used extensively by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which is appended hereto. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided.Comminution is responsible for a major portion of mineral processing plant energy consumption and operating costs. Bond Work Index efficiency provides valuable means, first, for benchmarking one’s plant performance against others in the broad industry, and hence defining the extent of the opportunity for improvement. Secondly, improvements in circuit efficiency with implemented changes can be quantified and monitored as part of continuous improvement efforts. These two important business activities are thus facilitated, and, in the absence of any other accepted method, otherwise would be lacking without the existence and application of this standard for comparison. While often loosely applied in the past by plant metallurgical staffs, the increased precision offered by this guideline provides much clearer definition of both the conceptual and statistical meaning of these measurements. Even a small improvement can be enormously financially important, but only if differentiated by measurement. This guideline was thus intended to provide industry improved means to differentiate comminution circuit efficiencies. Carbon footprint reduction is coincidental, but nevertheless can be substantial.The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies."

Jan 1, 2016

By L. McFarlane, D. Rollwagen

"Madawaska Mines produces a uranium precipitate (83-85% u3o8) using a magnesium oxide slurry to precipitate the uranium from solution. The solution, at approximately 9""0 g/l u3o8 is neutralized to a pH of 7.0. At the Eldorado Nuclear Refinery in Port Hope, the precipitate is not acceptable as a single feed to the refinery process. It was discovered that a 2% silica impurity caused emulsion problems in the solvent extraction column.After extensive studies of possible solutions, such as two-stage precipitation and solvent extraction, an acceptable solution was found. The selective precipitation of uranium at a pH of 3.5-4.0 using Hydrogen Peroxide produces an almost silica free product of higher purity (90-93% u3o8) to that of straight magnesium oxide precipitation. Introduction Madawaska Mines Limited is located four miles southwest of Bancroft, Ontario. The annual production of u3o8 is approximately 610,000 pounds. To produce the final product or yellowcake, nine separate steps are required. These are (1) grinding, (2) dewatering, (3) leaching, (4) acid filtration, (5) clarification, (6) ion exchange, (7) precipitation, (8) washing, and (9) drying and packaging. To illustrate these steps, a complete flowsheet of the mill is displayed on page three.The yellowcake is sent to Eldorado Nuclear Limited in Port Hope, Ontario for further concentrating and refining. As part of their routine specification check, a test called the amenability test is performed. This test indicates how a particular dissolved yellowcake product reacts to solvent extraction. The Madawaska yellowcake did not pass the test."

Jan 1, 1982

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By R. S. James, D. C. Peck, P. T. Chubb

"The East Bull Lake gabbro-anorthosite intrusion is one of several Early Proterozoic layered mafic intrusions occurring along the Southern Province - Superior Province boundary in the Elliot Lake - Sudbury region, Ontario. The base of the East Bull Lake intrusion comprises abundant plagioclase cumulates (Leucogabbronorite Zone) hosting two distinct styles of sulfide mineralization: (1) disseminated magmatic sulfides, and (2) disseminated to massive, structurally controlled sulfides. Both types of mineralization are enriched in Pd, Pt, Au, Cu and Ni. The host rocks to the sulfide mineralization display a range of interesting features including nodular textures, dendriticpegmatitic mafic pods, inclusion-rich zones (pyroxenite, anorthosite and granitic inclusions) and magmatic breccias. Disseminated chalcopyrite, pyrrhotite and pentlandite occur in concentrations of up to 100/0 within erratically distributed gossan pods near the base of the intrusion. The sulfides were originally precipitated from intercumulus liquids, but were subsequently recrystallized and locally remobilized along fractures during the major period of metamorphism and deformation that affected the East Bull Lake intrusion. The base- and precious-metal tenor of the structurally controlled sulfides can be explained by extensive remobilization and reconcentration of the pre-existing magmatic sulfides in the vicinity of a major shear zone. Both styles of sulfide mineralization locally contain ppm abundances of POE + Au and are generally Pd- and Cu-rich, although both display large variations in Pd:Pt and Cu:Ni ratios. The magmatic sulfides are more strongly enriched in POE and contain up to 1470 ppm Pd in 100% sulfide. Several factors, including source characteristics, magmatic processes (crustal assimilation, fractional crystallization) and post-magmatic interaction with hydrous fluid, have influenced the present distribution of POE, Cu and Ni in the East Bull Lake intrusion.The magmatic sulfide occurrences from the East Bull Lake intrusion compare favorably with marginal-type deposits from rift-related intrusions (Noril'sk-Talnakh region, Siberia; Duluth Complex, U.S.A.) in terms of their distribution, but are most similar to reef-type POE deposits with respect to their base- and precious-metal geochemistry. The combination of high POE tenors and large tonnages that is observed for the POE-Cu-Ni mineralization from the East Bull Lake intrusion suggests that a good potential exists for the presence of economic concentrations of Pd, Pt, Au, Cu and Ni in the intrusion. On a global scale, the East Bull Lake intrusion is part of a suite of Early Proterozoic plutons, many of which contain significant volumes of stratiform and/or marginaltype POE-Cu-Ni mineralization. The East Bull Lake intrusion is also one of the oldest mineralized intrusions derived from a sub-Superior Province mantle source region that has given rise to several significant magmatic POE-Cu-Ni deposits during the period 2.5 Ga to 1.1 Ga."

Jan 1, 1993

By Changmiao Liu, Dong Dong

"Magnesite is a major mineral resource in China, whose output and export are massive and quite important to the world. Flotation performances of eight anionic collectors on magnesite were studied to find the proper ones. Micro-flotation results indicated that collectors of HOl, SDBS and AEP had outstanding flotation performances on magnesite, with the recovery ratio all reaching above 90% in a wide range of alkaline pulp. Solution chemistry calculation, Zeta potential and FTIR measurements were employed to reveal the interaction mechanism between anionic collectors and magnesite surfaces. Solution chemistry analysis indicated that the main active components of HOl, SDBS and AEP were anions and association complex anions in alkaline pulp. Magnesite surface was negatively charged in the alkaline pulp. The active sites on magnesite surface were mainly the components of MgOH-, Mg (OH)2, and MgCO3 when the pulp pH was over 8. Anionic components of HOl, SDBS and AEP reacted with Mg in magnesite surface to make the insoluble anionic salts. And the chemical adsorption was confirmed by the FTIR measurement evidences.INTRODUCTIONAs an important industrial mineral, magnesite has been widely applied in metallurgy, building materials, chemical industry, agro-pasturage and other fields (Hu et al., 2006). It is a major mineral resource in China with abundant reserves. Its output and export are massive and quite important to the world. Liaoning province is rich in magnesite, whose reserves and production both come first in China. So far the proven reserves have reached 2.91 billion tons, accounting for more than 90% of total reserves in China, and more than 25% in the world (Li et al., 2012).Magnesite ores in Liaoning province mainly contain crystalline magnesite, and the gangue minerals of quartz, dolomite, talc, tremolite, chlorite and carbonaceous materials. Some ores also contain a little pyrite, chalcopyrite, hematite and apatite. Most of the ores must be preprocessed to separate the useful parts from the large amount of gangue minerals, so that their value and industrial application can be enlarged and promoted.Flotation is commonly used to process the magnesite ores, and the conventional flotation methods include anionic and cationic flotation. In the former, gangue minerals of silicates were separated by using amine type cationic collectors. After the impurity minerals were removed, high qualified magnesite concentration could be gained. For the cationic flotation method, it had some drawbacks of lower recovery ratio and poor performance in the lower temperature pulp (Li et al., 1995)."

Jan 1, 2016

By L. Hacini, N. Van L ê, P. Bacher, D. Thibault

Manufacturer welded components may suffer from high level of residual stresses which can cause premature cracking and decrease the life of the components if they reach values close to the yield strength of the material. In the present work, a robotized hammer peening technique is simulated by an impact machine and the residual stresses generated by the indentation are measured. To better understand phenomena behind residual stresses relaxation by hammer peening, the impact energy level was changed. 304L steel plates were hammer peened with 10 impacts. The contact between the hammer and sample surface was always at the same location. The strains on the surface close to the impact location were recorded during the test using strain gauges to follow residual stresses variations. At the end of the test residual stresses were measured indepth using hole drilling technique at 8mm from the impact center. The micro-hardness was monitored to evaluate the affected zone by the hammer peening. This approach gave a good estimation of the energy and number of blows to be used for efficient relaxation of the manufactured parts.

Jan 1, 2006

By P. Hubert, J. P. Ildefonse, F. Qafssaoui, J. Poirier

Corrosion tests by corrosive alumina-lime slags were carried out on commercial high alumina bricks used in steel ladle linings and model refractories (with different raw materials : bauxite, andalusite, and different microstructures). Using (SEM) scanning electron microscope and (EDS) energy dispersive spectroscopy, microstructures of slag-corroded refractory interfaces were studied in detail. The monomineral and glassy phases, the composition of reaction products and chemical profiles were determined. A thermochemical analysis based on phase equilibrium diagrams has permitted to estimate the proportion and the composition of the high temperature intergranular liquid phase. These data were compared to the experimental microanalysis results. The viscosity of the high temperature liquids were calculated according to Urbain 's model and the relationship between the viscosity and the penetration of liquid phases were discussed. These theorical and experimental results were used to understand the complex phenomena of slag penetration and corrosion of andalusite and bauxite refractories at high temperature and to propose new ways of improvements for the formulation of high alumina refractories.

Jan 1, 2004

"The last thirty years have seen enormous changes in all aspects of the gold industry, from the technologies of mining and extracting gold to the role it has played in the fiscal policies of nations. In this time, the market price of gold has increased ten fold and mine production has more than doubled. However, the cost of mining and extracting gold has also increased exponentially, and the industry has struggled with declining ore grades and increasingly refractory ore bodies.With the major economic powers of the world shrugging off the uncertainties of the post cold war era and moving into a period of unprecedented political stability, economic growth and low inflation, gold is also losing its lustre as a hedge against inflation and a backing for national currencies. Consequently, countries that had accumulated and hoarded gold for decades are now disposing of these non-performing assets, resulting in major swings in supply of the metal. Fortunately, this has coincided with the end of communism in many parts of the world and a tentative move to free market economies in most of the developing nations. As a result, people are becoming wealthier, and this is creating more demand for gold, principally in the form of jewelry.On balance, the shift in the role of gold, from one in which a significant portion of new gold production lay dormant in bank vaults as insurance against political or fiscal instability, to one in which most new gold is now freely traded as an industrial commodity, responding to normal market forces of supply and demand, has had a negative impact on the price of gold over the last fifteen years. In that time, the gold price has declined from a peak of $850/oz in 1980 to an average price of about $400 through the rest of the l 980's, to a price of -$320/oz today (1997). In large measure, this has been due to the enormous inventory of gold metal that was held by central government banks in vaults around the world, and which has been dumped on the market as soon as the price has started to trend upwards. Even today, after ten years of fairly steady selling by central banks, about 3 0, 000 tons of gold (or -8 years' supply at the present rate of consumption) is still retained in vaults (Murray et al., 1997).The downward pressure on the price of gold has created exciting opportunities for the development and implementation of new technology. Increasing the efficiency of gold recovery from more and more refractory ore bodies, whilst at the same time lowering production costs, have become critical to survival in this industry. These challenges have been met by the development and implementation of new technologies such as heap leaching, carbon in pulp, resin in pulp and the sulphide ore pre-treatment process of pressure leaching, bacterial leaching and fluid bed roasting. For an industry that saw very little technological change in the first seventy years of the twentieth century, the pace of change over the last thirty years must have seemed bewildering at times."

Jan 1, 1998

By Z. -G. Ren, J. -S. Qian, Y. -G. Yang

The waste slags from chemical and metallurgical plants contain approximately wt 1% water soluble Cr6+. This hexavalent chromium is very harmful to human health, and the treatment of the slags has concerned metallurgists for many years. A sintering method was developed to treat the waste slag. In this process, sinter was made from a mixture of the waste slag containing hexavalent chromium, iron concentrate and coke breezes. During sintering, hexavalent chromium was reduced to trivalent chromium. The latter is known as a non-harmful material and can be used as chromium resource for the production of ferrochromium or chromium-containing cast iron. After sintering the hexavalent chromium in the sinter could be reduced to less than 0.0008%. It was found that the waste slag with fine particles was favourable to the Cr6+ removal. An increase of carbon content in the sintering mixture could increase the rate of Cr6+ removal and the strength of the sinter produced. The rate of Cr6+ removal increased with increasing basicity of the sintering materials with basicity less than B=1.8, above which it decreased with increasing basicity. Blast furnace was found to operate smoothly when using the sinter made from the waste slag containing chromium. However the productivity of sintering machine was slightly low compared to the sintering operation using ordinary raw materials.

Jan 1, 2004

By E. M. De Souza

"The mining industry has developed a strong need for monitoring underground openings since bulk mining, used for increased productivity, has become the dominant mining method industry wide. The large stopes associated with bulk mining methods generally have to remain open and stable for several months, and monitoring is essential to provide an indication of ground response to mining and stope stability. The instrumentation data is also important during design optimization, which is used to maximize recovery, to minimize the dilution of ore and to minimize costs. Monitoring is essential to implement safety and is also critical in stope and mining sequence designs. The safety related aspects of monitoring include the protection of underground workers and the prevention of accidents by providing early warnings of the onset of any ground instability. The design related aspects of monitoring involve the development of data bases used for stope dimensioning and mine sequencing and timing and the monitoring of ground behaviour as a result of mining to verify the validity of the design thus allowing for remedial action during operation.Manual instrumentation data collection is, in a number of cases, economically unfeasible and, in many situations, dangerous as instrumented areas become inaccessible or extremely unstable. Also, because more and more complex instrumentation is being installed in underground operations, in several cases it becomes practically impossible to collect readings manually. The design and development of low-cost acquisition systems for mine wide monitoring would thus constitute an important step toward automation in excavation instrumentation. A unique menu-driven automatic 32-channel analog data acquisition and analysis system with a built-in rock failure warning mechanism has been designed and developed. This low cost acquisition system is capable of receiving, processing, displaying and storing the transmitted instrument data remotely and automatically. Computer software has been designed to provide data reduction and analysis immediately in the field and to automatically display results in graphical form for quick interpretation. Automatic data interpretation is used to show trends in rock mass behaviour and the system can be used to provide early warning of rock failure to the mine personnel working in there so that immediate remedial action can be safely taken."

Jan 1, 1992