Search Documents

By J. A. Stewart

"A common problem in the mining industry involves the overloading of established conveyor systems. This overloading can have a number of causes, such as new production technology or a changing market condition which increases demand. An overloaded system usually spells disaster and leads to clean-up problems, equipment failures and lost production. The Cape Breton Development Corporation's Lingan Mine had a serious overloading situation on its underground coal clearance system, and equipment was being damaged and production was being lost. It was rectified, in part, by increasing the coal clearance capacity through the use of booster conveyors. This paper discusses the problems which led to this situation, the booster concept and the installation of the first unit at the Lingan Mine.IntroductionThe Lingan Mine is a submarine coal mining operation with an annual production of 1.5 million tonnes from three advancing longwalls. Coal is conveyed 3400m up a 13% slope to the surface. Designed and installed in the early 1970s, the system's 820-tonne/hour design initially proved adequate; however, by the late 1970sthe system was handling surge loads of 1640 tonnes per hour due to the introduction of new face equipment.The coal clearance system consisted of three 485-Kw, two 210-Kw and one 105-Kw conveyors. Each conveyor was designed for 820 tonnes per hour using 1050-mm, Type 10 belt with a 35-degree troughing profile.There were many effects of the overloading on the system:• Loading beyond the physical capacity of the belt resulted in spillage along the conveyor, which increased operational and maintenance costs.• Overloading of the drive components resulted in premature equipment failures.• Spillage at the drive pulley often resulted in damage to the belt and pulley lagging and, under extreme conditions, the conveyor would require partial unloading before it would operate. This was a particular problem under wet conditions because the 485-Kw conveyor drives were fitted with single-drive drums."

Jan 1, 1982

By D. M. Morrison

"The most important factor in Canadian mining is not the operating cost of current projects but the availability of capital for future projects. The future of mining at depth will be producing ore from the top of the orebody working downward with very effective, tightly controlled mining methods, i.e. either selective mining or bulk mining with well controlled dilution and fragmentation. The key characteristics of future mines will be smaller access excavations, more effective ground support, very precise blasting techniques and more efficient and reliable materials handling systems. Equipment will be smaller and designed for high efficiency and low maintenance, reducing both the capital and operating cost. This means there will be fewer scoops, more continuous mucking machines and conveyor belts, both lateral and vertical.Orepass failures have become accepted and the resultant redevelopment and retramming has become common. The capital investment in so-called permanent ore passes and crusher stations becomes questionable, particularly when crushers are only necessary for less than 10% of the ore going through the system. The best way to solve the chronic instability of ore passes is, as with all of the stability problems at depth, by reducing the excavation size rather than increasing ground support. Smaller access drifts would reduce the capital cost and increase the rate of development as well as reduce the amount of waste to be handled, reducing the ground support and the ventilation requirements. Large drifts and ore passes are essential only for the equipment needed to handle large pieces of ore and the productivity of scoops is very expensive when the requirements for ventilation and large access drifts are taken into account. The key issue is the fragmentation generated by primary blasting.The future of mining in Canada will depend on simple and robust technology geared to the environment in which it will have to operate. Its survival will depend on some-thing much more fundamental and difficult to accomplish than a technological advance — it will require a dramatic change in the way the mining process is managed, how work is organized, how effort is rewarded and how costs are measured — a complete change in mind-set."

Jan 1, 1996

By Tapio Leskinen

"In the 1960’s, when large flotation machines appeared on the market, this was a part of a world-wide trend towards the use of ever larger machine units.One factor that has played a decisive part in this development is the increased of the amounts of ore that have to be handled as the exploitation of successively poorer ores becomes necessary. The advancing application of instrumentation and automation has worked in the same direction.In 1970, a working group was set up within Outokumpu Oy, for the purpose of flotation machine development. The principal task of this group was to be the design and development of- a new type of rotor of increased efficiency, especially for the dispersion of large amounts of air- a mechanical-pneumatic flotation machine of substantially larger size that existing plant.This development project required an extensive program of theoretical investigation and experimental studies at several concentration plants of the company.The commonest flotation machine presently used in the concentration plants of Outokumpu Oy is the VK-3. It is of the mechanical-pneumatic type, and the volume of its cell tanks is 2.5 m3 per shaft. This machine was developed within the company, and its first development phase i s represented by the OKKO 3, built for the Kotalahti concentrator in 1959. It was, in its time, comparable in volume to the largest machines that were then in use anywhere in the world."

Jan 1, 1976

By W. Greg Maybee

Separations, which form along stratigraphic boundaries in the roofs of potash mines, pose a serious safety concern. If these separations go undetected they can lead to falls of ground. The current method of identifying the location and extent of these separations is through manual scaling (sounding) using an aluminium rod. The potash mining companies would like to have a tool, which could quickly and reliably detect these separations and distinguish between them and clay seams. This paper presents the results of field trials undertaken at various potash mines in Saskatchewan belonging to the member companies of the Saskatchewan Potash Producers Association. A ground penetrating radar instrument from RST called SUSI (stepped frequency, ultra-wideband, synthetic aperture radar instrument) was used. SUSI has the ability of working over various frequency bandwidths. Four mines were chosen for these field trials, covering the different geological characteristics encountered in the Saskatchewan potash mines: Potash Corporation of Saskatchewan?s (PCS) Allan and Lanigan Divisions, Agrium?s Vanscoy Potash Operations and IMC Potash?s K2 Mine. These field trials indicated that stepped frequency ground penetrating radar technology could be ?tuned? to identify both separations and clay stratigraphy in the softrock, potash mine environment, based on the different spectral responses of the features.

May 1, 2004

By V. Prodanovic, M. Militzer

Production of advanced linepipe steels with strength levels of 685MPa (100ksi) and higher requires excellent control of runout table cooling to produce the desired final fine-grained microstructures, which may include acicular ferrite. Cooling is exerted on the runout table by applying water jets onto the hot surface of the strip and heat is removed from the steel by forced convective boiling. The associated boiling mechanisms are complex and include film, transition and nucleate boiling. A pilot-scale runout table test rig has been built to systematically study boiling heat transfer from a moving steel plate by employing industrial scale headers. Experiments were conducted using test plates moving at speeds between 0.3 m/s and 1.4 m/s. The plates were cooled down from 850°C to temperatures below saturation by a single water jet supplied through an industrial size circular nozzle. Based on these experiments heat fluxes were determined and further used to develop improved runout table cooling models.

Jan 1, 2005

By M. J. Michaud, M. J. Lavigne

"A cornerstone of any successful mining project is an understanding of the mineral assemblage and metal distribution comprising the deposit. Knowledge of the precise mineral/ metal zoning enables an operation to utilize different mining and processing methods optimized for different parts of the deposit. The Lac des Iles mine, located in northwestern Ontario, is one operation that depends on a good understanding of these issues. Current resources for the Roby Zone total 94.1 Mt grading 1.66 g/t Pd, 0.18 g/t Pt, 0.14 g/t Au, 0.062% Cu, and 0.053% Ni.The Roby Zone occurs within the gabbroic portion of the Lac des Iles intrusive complex and consists of three compositionally and texturally different ore types with variable PGE, base and precious metal contents. PGE occur as sulphides and bismuthotellurides in net-textured sulphides, coarse sulphide blebs and as finegrained inclusions within secondary silicates.Knowledge of the precise mineral/metal zoning has directly and indirectly improved several operational aspects, including resource modelling, mining, and processing. For example, metallurgical recoveries have been increased by up to 3% to 5% and concentrate grades have increased by up to 100%. IntroductionLac des Iles Mines Ltd., a wholly owned subsidiary of North American Palladium Ltd., owns and operates a 3000 t/d open pit mine and concentrate facility, located 100 km north of Thunder Bay in northwestern Ontario. The Lac des Iles PGE-gold-copper-nickel mine has been in commercial production since 1993 and in 1997, produced 1.8 million grams of palladium, 127 000 g of platinum, 114 000 g of gold, 438 000 kg of copper and 354 000 kg of nickel (North American Palladium Ltd., 1998).Under the Industrial Research Assistance Program (IRAP), a two-year study of the mineralogy of the Roby Zone was undertaken with a goal of improving the profitability of the mine. Geological mapping, petrography and geochemistry of the Roby Zone were completed during this study. Utilization of the detailed mineral/metal zoning identified as part of this study was implemented at the mine and shown to positively impact many operational aspects including mining and processing."

Jan 1, 2003

By Masayuki Ishikawa

In a radio frequency and optoelectoronic device packaging, Gold-Tin (Au-20 wt% Sn eutectic) solder is used widely due to the excellent electrical and thermal conductivity, high strength, and negligible creep characteristic under repetitive thermal cycling. With the recent lead-free movement, Gold-Tin solder is recognized as an alternative material for high temperature Lead-Tin solder. Generally, Gold-Tin solder is supplied in the forms such as ribbons, pellets, and ring frames. However, these forms must be set-up accurately on the joint area to press chips in bonding, therefore, it is difficult for these forms to satisfy the recent requirements for the down sizing in the connection areas. On the other hand, Au-20 wt% Sn solder paste can be applied flexibly to various supplying methods, such as printing, dispensing system and pin transcript. These methods also make it possible to reduce the production cost. However, in the case of using the solder paste, the void issue is one of the most undesirable problems. The void causes the degradation of the characteristics such as the bond strength, electrical characteristic and thermal conductivity. We have been intensifying the development of the void free paste, and have achieved void reduction by optimizing the powder size, the flux composition and the reflow condition.

Oct 1, 2003

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

By L. H. Michaud

"Albian Sands Energy (ASE), an oil sands surface mining and extraction operation, is currently undergoing start-up and is scheduled to ramp-up to full production by mid-2003. Startup includes the selection and implementation of over 75 IT systems or computer applications which include: engineering applications; systems required to control mining activities, maintenance, the processing plant and utilities; and also systems required to run the company, such as human resources, finances and inventory/ warehousing.This paper outlines the processes used for the selection, implementation and integration of these systems in order to optimize the use of information and to meet the technical, business and IT requirements of the company. The first step in ASE’s approach to identifying system requirements is the development of a business activity model, outlining all tasks involved in running the operations. The computer applications required to accomplish each task are then identified by having the IT team work closely with each technical and business unit. Historically, at some companies, the selection of systems has been led by the IT team or by consultants, with little input from the technical or business units. Typically, this results in products that do not meet the company’s expectations. To ensure a more positive outcome, ASE believes that it is imperative that the company’s technical and business people be closely involved in the selection process.Integration of the IT systems is also key, including linking all applications through a data warehouse and EDMS. Over 120 required integrations have been identified. This ensures the storage of all data in only one location, data security, and easy data and document retrieval for all requirements throughout the company"

Jan 1, 2003

By A. J. MacEachen

"LIKE ALL OTHER NOVA SCOTIANS, I have been thrilled during the past few years with the growing evidence that substantial reserves of oil and gas are being discovered off the Atlantic coast of Canada. There are those in this province who believe that large-scale commercial production is just around the corner, and that when it starts Nova Scotia will begin to float on a sea of royalties. These overly optimistic people, of whom I am not one, are convinced that with the first barrel of oil shipped to market, Nova Scotia can forget its financial problems while its people take on the luxurious lifestyle of the shieks of Kuwait or Saudi Arabia. You and I know, however, that even though offshore oil and gas may turn out to be the greatest gift nature has ever bestowed on Eastern Canada, it may take some considerable time before the reserves can be accurately assessed, before the industry can become fully operational, and before the benefits of production can be translated into royalties and tax revenue, improved public services, new industrial facilities and more jobs. While it is premature for the ordinary Nova Scotian to take on the habit of buying expensive cigars and lighting them with ten-dollar bills, it is not too early for him to insist that governments and industry plan intensively and well for the beneficial exploitation of undersea resources."

Jan 1, 1973

By M. Drozd, M. Somppi, Z. Yamak

"Granular activated carbon is widely used in the gold mining industry for gold extraction from aurocyanide-containing slurry. The extraction process can employ carbon as part of the gold recovery operation for various circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) circuits. However, various qualities of activated carbon exist and the durability of the material can change significantly from source to source. Handling this expensive reagent can pose challenges when fine carbon losses occur in the CIP, CIC, and CIL circuits. Additionally, any gold that is adsorbed to these carbon fines can also be lost by various mechanisms including carbon attrition and fracturing, inefficient coarse-fine separation, and poor carbon fines capture. With the above in mind, a series of tests were conducted to investigate standardizing simple laboratory methods for testing carbon quality. A standard procedure beyond or enhancing ASTM methods can serve as additional starting points for evaluating carbon specific to the gold industry. The investigation focused on size distribution, flatness, wet attrition resistance, surface area, gold kinetics, and gold loading. The final results provided information to generate an equation for ranking carbon samples to plant performance.IntroductionActivated carbon for use in gold extraction is amongst the most commonly found processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on the importance of maximizing gold recovery. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes."

Jan 1, 2017

By P. Fossi

This report describes a pilot-scale study of a hydrometallurgical process to treat high-grade nickel matte or a nickel-cobalt sulphide precipitate to produce high-purity electrolytic nickel. The first step of the process is the oxidative leaching of the nickel-bearing material by nitric acid; the nitrous gases generated during leaching are reconverted to nitric acid. The crude nickel sulphate nitrate solution is purified and is then subjected to a denitrification step. Nitrate separation is effected either by the crystallization of nickel sulphate or by precipitation of basic nickel carbonate. The electrolyte is prepared from the nitrate-free material and nickel is then recovered by electrolysis of the sulphate solution using insoluble anodes. Some technical and economic problems encountered with this processing route are discussed and the method is compared to the "all-chloride" process developed by Société Le Nickel.

Jan 1, 1977

By Graham A. Davis, Michael Samis

The dramatic fluctuation in metal and energy prices in the last few years is causing mining companies to consider alternative analytical methods for mine design and valuation. The goal is to improve insight into unforeseen changes in the economic and project environment and to design projects that take advantage of management's ability to respond to these changes. Such flexibly managed projects will contain value that cannot be measured using traditional engineering economic approaches, further motivating the used of alternative, modern valuation methods. This paper considers the valuation of an uneconomic low-grade resource at an open pit gold mine using two of the most popular modern valuation methods, Dynamic Discounted Cash Flow and Real Options. Our analysis demonstrates that the conventional valuation method may incorrectly represent the value and risk attached to mining this type of resource because it is unable to recognize management's ability to respond to future events in a manner that minimizes losses and exploits advantageous business conditions. The results of this paper highlight the importance of recognizing flexibility and business uncertainty in both mine design and valuation.

Jan 1, 2003

By R. W. Mei, R. A. Strombom, D. J. Moore

"Heat-shrinkable cable accessories are solving problems in the mining industry. This paper describes a range of products used by the industry, including low-voltage splices, high-voltage splices to 8.7 k V, cable repair sleeves, mining cable terminations used on system voltages up to 25 kV and motor connection kits up to 8 k V. Technical procedures and designs are illustrated.IntroductionThe development of high-performance heat-shrinkable materials slightly over 20 years ago proved to be one of the major technological breakthroughs in power cable accessories. Heat-shrinkable products were introduced initially for use as low-volt age cable accessories in the aircraft and electronics industry. A program of continuous development and product introduction now enables the manufacturer to offer a broad range of products for mining, industrial and utility electrical systems.With the advent of atomic energy, an important discovery was made-exposure of some plastic materials to high-energy electrons can cause the permanent crosslinking, or intermolecular joining, of adjacent molecules. Once the material has been crosslinked, it will not melt or flow at any temperature.The unique properties of heat-shrinkable products also result from the exposure of special thermoplastic formulations to high-energy electrons. Because of crosslinking, these products have perfect elastic memory. The heat-shrinkable products are supplied in expanded condition. When heated, they will shrink and tightly cover the object over which they have been placed. 'The functional and operating demands of mine cable accessories exceeded the classic electronic applications of heat shrinkable materials. These demands required a very sophisticated program to develop materials and adhesive systems that could endure the operational environment associated with the mining industry,Ease of assembly, low installed cost and operational reliability are among the main reasons for the acceptance of heat-shrinkable mine cable accessories in electrically powered mines. For over a decade, these systems have been demonstrating proven performance."

Jan 1, 1980

By S. Hunt, D. de Vries

Kansanshi Copper Smelter began operation in March 2015. The smelter features a single Isasmelt furnace for smelting, one 6-in-line electric furnace for matte-settling and slag-cleaning duties, four Peirce- Smith converters and two rotary anode furnaces. A 1,450 t/day oxygen plant and a 4,085 t/day sulphuric acid plant are included in the smelter operations. This paper gives an overview of the operational performance to date with summary data for each smelter section. Challenges such as an unforeseen refractory failure in the Isasmelt furnace in 2016 are discussed. Design improvements around the electric furnace are mentioned. Plans for potential future improvements are put into context. A consistent focus on operations, maintenance and continuous improvement has seen the smelter easily achieve its nameplate capacity of 1.2 million tonnes per annum of copper concentrate throughput. The smelter now operates consistently at a concentrate throughput rate of 1.38 million tonnes per annum of copper concentrate. INTRODUCTION The smelter was commissioned in March 2015. Design and commissioning of the smelter have been discussed by de Vries, Hunt, Hanschar and Louie (2016). The smelter rapidly ramped up to achieve nameplate production (1.2 million tonnes per year concentrate) and in 2018 operated consistently at the rate of 1.38 million tonnes per year concentrate. This paper presents major operational data for each section of the plant and describes significant events and improvements during the first four years of operation. The smelter flowsheet is shown in Figure 1.

Jan 1, 2019

By Chen Xia, G. Deschenes, Wan-Tai Yen

"Ammonium thiosulphate is a potential replacement for the cyanide in gold leaching. However, the high reagent consumption hinders its practical applications. In order to reduce the thiosulphate consumption, chemical additives were used. The gold leaching tests were conducted on a sulphide copper-bearing gold ore with 0.3M thiosulphate, 0.03M copper sulphate and 3M ammonium hydroxide solution at 44% solids and pH 10.2. Sulphate, sulphite, amino acid and chelating agents were initially used as additives. It was found that chelating agents (EDTA and NTA) could reduce the thiosulphate consumption from 30 kg/t to 17.8 kg/t with some increase of gold extraction. The improvement from other additives was not significant. Other approaches were also attempted to reduce thiosulphate consumption with some success. The thiosulphate consumption could be reduced to about 17 kg/t by reducing copper sulphate concentration fiom 0.03M to 0.0015M; adding 0.04M of EDTA; replacing copper sulphate with 0.001M of nickel sulphate. The increase of pulp density fkom 44% to 60% solids could reduce the thiosulphate consumption to 17 kg/t as well. Limiting the dissolved oxygen content by sparging nitrogen reduced the thiosulphate consumption further to 10 kg/t. It could be concluded that the regulations of copper and oxygen supply in the lixiviant were the keys to reduce the reagent consumption.INTRODUCTIONCyanidation, as the predominant gold leaching method, has been used in mining industry for more than a century. The low reagent requirement and the high performance are the reasons for its great success. However, cyanidation cannot deal with ores containing large amount of copper, nickel, arsenic and zinc minerals. This type of ore may consume more reagents and result in a poor gold extraction. On the other hand, the carbonaceous materials may preg-rob the gold from pregnant solution and make cyanidation a problem leaching method. Further more, the high toxicity of cyanide represents another challenge to modern gold mines. In the beginning of the year 2000, an environmental disaster caused by an accidental spill in Yugoslavia was broadcasted world-widely (Gurevitch 2000). Gold mine operators are facing higher social pressures and increasing costs on environmental protections. The usage of cyanide in mining industry has been banned in some countries and locations such as Czech Republic, Japan, Turkey, California, Colorado, Wisconsin and Montana States. Thus, a non-cyanide lixiviant is required."

Jan 1, 2002

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By John Russell

"Faster, safer, grinding mill relining offers the obvious attractions of reduced mill relining times with the knock-on incentive to reduce all other maintenance down-time, opening the possibility for increased annual plant utilisation.Leading edge liner handler technologies by RME, focused toward even shorter relines for very large SAG and AG mills, have recently split into two quite distinct paths:•,?Single SAG/AG Mill Relining Machines (MRM’s) of very large capacity, such as Newcrest Cadia’s 40’ SAG MRM of 6000 kg capacity and P.T. Freeport’s 38’/34’ SAG MRM of 7250 kg capacity;•,?Twin-machine SAG/AG Mill Relining Systems of moderate to large capacity such as BHP Billiton’s Escondida Laguna Seca 38’ SAG MRM’s, each featuring 4500 kg capacity.RME, its customers noted above and their liner suppliers are providing leadership in this important annual utilisation advance.Once the 24 hour mill shell reline becomes reality, liners designed for maximum profit, not maximum life, albeit exchanged more frequently, become possible too.INTRODUCTIONAt most mineral grinding plants, mill relining activities dictate each maintenance shutdown’s critical path. When annualized, mill relining remains the largest, single influence in defining plant availability.Because of restricted access, both inside and outside the mill, increased application of manual labour has no effect on reducing relining downtime. The only answer for RME has been to develop and apply new relining technologies now known as RME’s Mill Relining System.RME’s primary focus for over twenty years has been the reduction of grinding mill relining times while simultaneously providing a marked improvement in relining safety. Our original (1990) target was to halve traditional (pre-RME) reline times and to eliminate accidents and injury by mechanizing all physical work."

Jan 1, 2008

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009