Search Documents

By Nordau R. Goodman

T-he Ojibway Salt Mine near Windsor, Ontario, produces almost two million tonnes of97% pure rock salt annually. The salt is mined from the middle F horizon of the Silurian Salina Formation. The salt beds have a gentle dip into the Michigan depositional basin. There is no evidence of deformation. The rock salt is buff coloured and has a number of thin carbonateanhydrire bands. Secondary salt crysrallization occurs throughout the mine.

Jan 1, 1984

By Scott D. Long

"Abstract-Grass roots exploration has an emphasis on good precision at low (sub-economic) concentrations of an element, in order to identify "anomalies" which may lead to drilling targets. Although it is wise to have well-defined quality controls in place during early stage sampling, the control procedures at this stage tend to be rudimentary. When a deposit warrants detailed delineation, the need for accurate geological characterization and assaying of ore-grade rock must be supported by appropriate quality control procedures.As a project returns more promising results, and the likelihood of the project warranting a prefeasibility study increases, it is time to tighten quality assurance requirements and quality control protocols. Delays in instituting adequate quality control and verification procedures may lead to costly remedial actions that can also delay completion of the prefeasibility or feasibility study. Sometimes, as a project matures, the quality control and quality assurance aspects fail to keep pace with the changing nature of the work: an increasing emphasis on precise and accurate assaying of oregrade rock.A resource model is like a house of cards. The foundation of the house is the geological observations, the sampling methods and the geological interpretations performed upon those samples. Upon the sampling, which includes all the sub-sampling steps of sample preparation, rest the assay results. The quality of the assays can be no better than the quality of the sampling. Good assaying technique will preserve all biases and imprecisions introduced during sampling and sample preparation; it cannot remove them. If the sub-samples and/or assays are bad and must be redone, all the succeeding levels of the house of cards must also be rebuilt, or at least patched up.From geological observations, a geological interpretation is built, the quality of which is critical to the construction of an acceptable resource model. Geological elements are difficult to assess, and are not discussed here; they are dependent upon the expertise of the geologists involved. Geological knowledge contributes essential quality control elements to resource/reserve determinations (Sinclair and Postolski, 1999; Postolski and Sinclair, 1999).This paper consists of five sections: (1) overview of quality control protocols, (2) maintaining quality control of databases, (3) quality control of drill sampling, (4) optimizing crushing and grinding requirements, and (5) quality control of assay data acquisition."

Jan 1, 1998

By Y. O. Fortier

"ForewordTHE Arctic Archipelago and northern Greenland contain an orogenic region that is as much as 300 miles wide and over 1,400 miles long. It occupies much of what was formerly classified with the Arctic Plains and grouped with other plains and lowlands of Canada as one main geological division. It is proposed that this folded region be designated the Innuitian Region and be recognized as one of the main geological divisions of Canada.Canada's main geological divisions (see Geological Survey of Canada, 1947) have been considered as consisting of a central shield, largely surrounded by plains that separate it from eastern and western mountains. The plains include the Interior Plains, the St. Lawrence Lowlands, the Arctic Plains or Low-lands, and the Hudson Bay Lowland, which is in the central part of the Shield. Plains and mountains are, strictly speaking, physiographic terms, but because mountains are generally folded regions and plains are generally made of undisturbed strata, such terms are useful vehicles to express the fundamental make-up of the land. Nevertheless, it is preferable to use the terms Appalachian and Cordilleran 'Regions' rather than 'Mountains', as those geological divisions are not exclusively made of mountains.Because of the lack of more definite information, the 'Arctic Plains' have included, in the past, regions with plateaux two to four thousand feet above the nearby sea, mountain ranges reaching approximately 10,000 feet above sea level, and regions of folded strata."

Jan 1, 1955

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By Zhongxue Li

This paper reviews an analytical model that defines the relationship of weight-weighted or volume-weighted average haulage distance with bench height and other related parameters, presents the optimum bench heights under various conditions in terms of minimizing the weighted average haulage distance of ore/waste during the full lifetime of an open pit mine, and discusses the truck haulage economics of mining open pits by high bench, specifically by 15 m, 18 m and 20 m benches through marginal analyses. The observations from these analyses disapprove the previous conflicting assertions that the over-all weighted average haulage distance either increases or decreases directly with bench height. It is concluded that: (1) an increase of bench height to 15 m from 12 m is likely to be viable under the general conditions of large-scale deep open pit mines; (2) the reduction of haulage cost is much limited with the case of increasing bench height to 18 m from 15 m; and (3) the feasibility of mining open pits by 20 m benches is generally questionable. These conclusions may serve as a useful guide for those who advocate open pit mining by high bench.

Jan 1, 1995

By Marty Hudyma

Mining-induced seismicity and rockbursting is one of the primary risks in deep mines. Seismic data management software has been created to facilitate analysis of mining-induced seismicity. The Mine Seismicity Risk Analysis Program (MS-RAP) is a purpose built database with mine seismicity analysis tools. One of the primary features of MS-RAP is the creation of seismic hazard maps in quasi-real time. The seismic hazard maps identify areas that are more prone to large seismic events and rockbursts, allowing risk management measures to be focused on the areas of greatest risk. These maps allow mining engineers to be more proactive about identifying and managing seismic related geomechanics risks in mines.

Oct 1, 2009

By G. J. Hutchins

Precision surface mining is gaining traction in the iron ore, copper, iodine, limestone, bauxite, coal and gypsum markets. In this paper, we first address the possible improvements of a surface miner control using GPS techniques. An application in an iron ore mine in Western Australia is presented. The second item addressed is improvements of a new drum driving technique for a 100 ton surface miner. This technique involves installing a slow speed hydrostatic motor directly on the cutting drum rather than driving the drum through chain and sprockets. Details of the performance of this direct-drive versus the chain-drive are detailed. In addition to the 100 ton machine, we also present a 200 ton surface miner. This larger machine has 1600 hp (894.8 kg), and has been successfully introduced into a large iron ore mine in Western Australia. Performance of the 200 ton surface mining machine in various rock hardnesses is detailed. Some comments on the cost effectiveness of using a built-in loader versus loading with wheel loaders are included.

Aug 1, 2013

By S. C. Tadolini

"Roof bolts are the primary means of roof support in underground mines in the United States. Presently, post installation loads are measured on about 10% of the expansion anchor and combination bolts by using standard torque wrenches that Unit the accuracy of the measurements to about ±30%. No system has been available for measuring the loads generated on full-column resin grouted bolts. Mine roof bolts are long, slender, non-uniformly sized, roughly forged, and placed in a corrosive environment, creating obstacles for researchers trying to utilize ultrasonic reflection techniques to measure strain. A complete measurement system has now been developed by the U.S. Bureau of Mines, Denver Research Center. This system is being used successfully in determining loads measured on expansion anchor and combination bolting systems, examining the transfer mechanics of full-column, resin-grouted bolts, and measuring loads generated on bolts in an underground roadway support system.IntroductionMillions of roof bolts are used each year to provide structural support in underground U.S. metal, non-metal, and coal mines. Approximately 45% of the bolts used are expansion anchor, 45% are resin-assisted combination or full-column resin-grouted, and 10% are friction anchored. The effectiveness of these bolting types is dependent on a number of factors including rock density, bolt length, in situ stresses, rock properties, bolt pattern, installation tension, etc. When implementing expansion anchor and resin assisted combination bolts , installation and post-installation tension, or load, is a major determinant of support quality and subsequent behaviour of the reinforced roof. The method by which these systems carry roof loads is well understood and documented(1,2).The importance of these installation and long-term bolt tension measurements is well recognized and are required in the federal government regulations(3). A statistical sample of the bolts, lout of 4 during installation and lout of 10 inby the last open crosscut, is required to be measured using current torque wrench technology. The disadvantages of this system are the disturbance and weakening of the anchorage and limitations of accuracy to approximately ± 30%. The method by which resin-grouted bolting systems carry roof loads is much less understood, mainly because testing procedures used to evaluate point-anchor systems are not effective on resin-grouted bolts.Due to these problems, the U.S. Bureau of Mines designed a measurement technique that provided a highly accurate, low cost-per- bolt system that led to the development of ultrasonic pulse echo instrumentation. The original system was designed to measure the tension only on expansion anchor bolts. Recent developments and system modifications have permitted measurements on resin-assisted and full-column resin-grouted bolts. The use of these types of support systems has been increasing steadily in underground coal mines.The development of this instrumentation has provided laboratory and field results that help to explain the mechanics and relationships between the applied loads and the interaction between the grouted bolt system consisting of the bolt tendon, grout, and rock."

Jan 1, 1990

By R. H. Seraphim

"The Phoenix Camp, in the Boundary Creek district of southern British Columbia, produced before 1920 about 15 million tons of ore averaging more than l ·5 per cent copper, about 0.03 ounces per ton in gold, and 0·5 ounces per ton in silver. Attwood Copper Mines Ltd. conducted an exploration program in the Phoenix area from 1951to1953.Publications on the camp are listed in the bibliography. Brock's work was not sufficiently detailed to unravel the structural and stratigraphic pro bl.ems. The work of LeRoy and McNaughton is referred to later.The stratigraphic column is as follows:Tertiary.Midway Formation: Volcanics and hypabyssals; dacitic to basaltic flows, with associated dykes and sills of syenite (pulaskite in part) and augite porphyry.Jura-Cretaceous.Intrusives of quartz diorite and diorite (nearest outcrop two miles from Phoenix).Late Palaeozoic or Triassic (Attwood Series).Brooklyn Formation: Sharps tone conglomerate, limestone, grey-wacke and/ or andesitic tuff, with minor shale and basalt. Rawhide Formation: shale with minor conglomerate.Early Palaeozoic.Knob Hill Formation: Chert and andesite, with minor limestone, shale, and serpentine.This column differs from that of LeRoy in two important respects: (I) Attwood's work indicates that the Rawhide shale is basal to, rather than stratigraphically above, the Brooklyn formation. The shale contains conglomerate lenses, which become more abundant and thicker toward the top, and grades upward into Brooklyn conglomerate. Ripple marks indicate that the shale is right side up."

Jan 1, 1949

By A. J. Basu

Air quality in underground mining operations can fluctuate significantly during the working day, but until recently the only way to ensure a mine had sufficient air quality was to over-ventilate and, with significant delay in adjusting the volume or direction of the airflow, working conditions were tolerable but rarely ideal. Underground ventilation management systems have been considered to achieve improved energy efficiency since at least 1995 in Canada. However, Mine Ventilation Optimization, (MVO) and integrating it with Ventilation on Demand (VOD) is only becoming more of a reality in the last seven (7) years. A systems approach to MVO takes into account all the elements from the point the power is distributed into the ventilation fans through to the actual quality and quantity of fresh air to the working face. Opportunities exist throughout the system for energy savings but not all of them are cost-effective. Depending on the application, these opportunities can be easily realized by properly sizing, streamlining, maintaining and operating the ventilation system using premium mine proven energy efficient components throughout. Implementation of VOD is a key step in achieving the MVO objective. However, VOD is a concept, and it requires various tools, procedures, and strategies for cost-effective and operationally viable implementations. This paper provides a historical background in the development of VOD and provides a framework for proper and cost effective implementation. In addition, an optimized ventilation system will also allow increased airflow by reducing resistances and shock losses. This turn in would allow production target improvement, which could be an attractive objective compared to energy savings. Mine ventilation is the life support system of an underground mine, and contributes to sustainable development and corporate social responsibility goals assuring health and safety aspects of strategic planning. The proposed framework addresses implementing mine ventilation optimization integrating ventilation on demand as a vehicle for energy, health and safety improvement and overall productivity gains in the mining cycle efficiency while significantly reducing carbon footprint of a mine.

Aug 1, 2013

By C. Sist, J. Shannon, J. Fossenier, J. F. Adams

With the cleanest and easiest to treat copper concentrates dwindling and becoming harder to find, electrorefineries must deal with the reality of higher impurity anodes. There are well-known strategies for managing nickel, bismuth, antimony, etc. using bleeds (Ni, Bi, Sb, As) or arsenic control (Bi, Sb) or hydrometallurgical add-on circuits (IX, MRT, SX for As, Bi, Sb). However, for integrated copper producers and those producing other base metals it is often worth considering a more holistic, global approach. This paper will discuss both the well-known strategies as well as some global strategies and the role that hydrometallurgy can play in them. Examples will include atmospheric and pressure leaching, selective precipitation and impurity recycling or fixation. INTRODUCTION In the electrorefining of copper, impure copper anodes are electrically corroded, and pure copper is deposited on cathodes by passing DC current through an acidic copper sulphate solution. The anode copper impurities either settle to the cell bottom as insoluble components (anode slimes) or remain in solution with minimal deposition at the cathodes when correct operating parameters are maintained. Consideration of impurities is important in all copper electrorefineries. A typical impure anode contains 98.5–99.5% copper (Schlesinger et al., 2011). Table 1 shows the range of impurities reported for all copper anodes in the 2007 survey of operating refineries (Moats et al., 2007). Also shown is an approximate “limit” of anode compositions within which the majority of refineries operate without additional impurity removal capacity (beyond conventional liberator/bleed circuits). The column is somewhat subjective and meant to be an approximation only since there are many factors that influence impurity deportments and refinery impurity tolerances. More recent world survey data from 2013 show the averages for all impurities trending upward from 2003 to 2013 (Moats et al., 2013). With a competitive market for good concentrate and more copper recycling from electronics (which contain high levels of impurities such as nickel, lead and antimony), this trend is expected to continue through the coming years. The traditional primary method of impurity control is refinery bleed through liberator cells which are employed in the vast majority of refineries (Moats et al., 2013). These are used to control copper (primary liberators), nickel, arsenic, antimony and bismuth (secondary and tertiary liberators). Other methods of impurity control include arsenic addition (upstream in the smelter deporting to anode or directly to electrolyte) to control antimony and bismuth (Kamath et al., 2003), ion exchange or molecular recognition technology (Hur et al., 2005; Navarro et al., 2012) for antimony and bismuth. Many refineries also operate nickel evaporators to remove nickel sulphate before recycling back acid. Some use, or are contemplating using, acid purification units to recycle acid and arsenic without nickel and making nickel carbonate (Kamath et al., 2003; Sheedy et al., 2006).

Jan 1, 2019

By A. M. Hadian

The use of dolomite refractories in steel making and cement industries has advantages over other basic products particularly in countries where this type of refractories is produced. Due to existence of high-quality dolomite deposits in many regions of Iran, there is a good potential for producing dolomite refractories in the country. This study focuses on the effect of such additives as iron oxide and alumina on hydration resistance and density of Iranian dolomite. It was found that addition of Fe2O3 is more effective than Al2O3 on increasing density as well as resistance to hydration of dolomite.

Jan 1, 2004

By Bert S. Hall

"IntroductionThe purpose o f this paper is to review the evidence at hand concerning the earliest centuries of cast iron in Europe, from roughly 1400 A.D. until the second half of the sixteenth century. For the most part it is concerned with the relationship between two technologies which emerged first in China and then later appear in Western lands, gunpowder weapons and iron founding. We should not assume, as I hope to show later in this discussion, that weapons constituted the only product for which the iron founder had any market, but it is clearly true that attempts to produce weapons constituted the most severe technical challenge for the early founder. Firearms appear for the first time in Europe in the 1320s and develop into significant weapons on the field of battle by the end of the century. Theirs is a complex history, subject neither to easy summary treatment nor to simplified models of development. I hope to be able, through the analysis of the evidence concerning cast iron, to show that one important strand in the fabric of gunpowder's history concerns the materials from which cannon could be made. This question is subject to a number of shades of meaning, because ""cannon"" can be made for many purposes under a profusion of different names, and under sharply varying conditions of use. As a result, the question of materials is frequently really a question of competing materials, and involves a complex set of factors, of which production costs and the ultimate safety of the user seem the most important. Judged in this manner cast iron was an important but unsatisfactory metal for weapons purposes until 1543, at which time English founders learned to make iron muzzle-loading cannon which could rival bronze ordinance in most important performance criteria, but which cost much less to produce. With that event, the history of cast iron and the history of weapons entered into the close relationship that persisted until the advent of rifled artillery made of steel in the middle of the nineteenth century."

Jan 1, 1983

By J. P. Messervey

As a result of my field examinations in this Province, I have been struck by the evidence of widespread mineralization in rocks, particularly the limestones of Carboniferous age. Six prospects of lead and zinc or lead alone scattered through the eastern part of the mainland, one copper prospect and three veins of siderite, all point to a period of mineralization subsequent to the forming of the Carboniferous rocks in which they occur. While none of the present prospects are of proved economic importance, still it is possible, and indeed probable, that further prospecting will find concentrations sufficiently large to make mines. It may possibly aid the prospecting for these base metals if the present scraps of information are assembled from various sources, and I will further briefly recount the information as a result of my observations. Gay?s River At Gay's river, midway between Halifax and Truro, and four miles east of the railway, numerous pits and natural exposures show galena and sphalerite in limestone of Carboniferous age, near where it lies unconformably upon slate and quartzite of the gold series. These exposures extend for a length of over one thousand feet along a curving contact. The pits show that on the contact there is a fossiliferous and somewhat porous layer of limestone, which is so impregnated with galena and small amounts of sphalerite as to be of ore grade. Wherever observed, the thickness of this layer is less than two feet.

Jan 1, 1929

By James H. Savory

"In recent years, there has become a growing interest toward a better understanding of balance rope behaviour. With this in mind, the auth or will present a comprehensive summary of field experience, as well as conclusions. In presenting this overview, it is the intent to stimulate further interest as well as provide a framework from which further in-depth investigation can be initiated.Topics which will be covered include rope cores, lubrication practices, loop dividers, rope failures, etc.IntroductionThe first friction hoist was designed in Belgium in J862 by Lemielle. However, it was not until 1877 when Carl Frederich Koepe installed a friction winder sheave at the Hanover Colliery in Germany, that the design was given serious consideration. The winder consisted of a motor-powered sheave over which a single rope was installed, and the end s attached to two conveyance s. Beneath the conveyances a rope was connected, designed to reduce the chance of slip. This was the first balance rope.This earl y mod el is a far cry from the modern tower or ground mounted Koepe winders employed throughout the mining industry today. There have been vast improvements in all aspects of the Koepe winders. One such improvement is in the balance ropes used. This particular area will be concentrated on, with emphasis on selection, maintenance and field experience.SelectionThe sale purpose o f a balance rope is to counter the head rope weight. Obviously then, in selection o f balance ropes, weight is of primary concern. Usually the head and balance ropes are equal in weight. However, sometimes balance ropes which are 5 to 10070 heavier than the head ropes are employed. These reduce horsepower demands during peak acceleration periods, and assist in overcoming inertia during retardation periods. As well, it is sometimes preferred to reduce the balance rope weight, in order to compensate for the eventual weight buildup of lubricant, dirt and debris."

Jan 1, 1983

Falling asleep at the wheel of a moving vehicle is not only dangerous but avoidable. It is implicated in up to 30% of all road fatalities in general and up to 65% of mining incidents involving haulage trucks. These types of crashes normally result in serious injury and/or fatality due to the lack of breaking that occurs. However, when a 300 tonne haul truck has a sleep related crash it is not only the safety of the driver that has a high price but also the commercial impact on the mines? productivity and efficiency. We have been developing our ASTiD technology which stands for the Advisory System for Tired Drivers to seamlessly integrate in to Modular Mining?s Dispatch system to provide real-time early warning fatigue risk management. The benefits being driver shift optimisation, sustained productivity and of course less accidents. By monitoring the drivers alertness levels in real-time using ASTID, the Dispatcher becomes empowered to make critical, management decisions that will ultimately prevent serious injury or loss of life and the driver gets to stop when he needs to and not just when he is supposed to. This paper shows how this integrated solutions works.

May 1, 2011

By L. Freitag

"The Dollard oil field in southwestern Saskatchewan is a stratigraphic trap of irregular shaped perimeter. The reservoir is a low-angle monoclinal structure with a dip of approximately 100 feet in 5 miles from west to east across the long axis of the reservoir. Production of. 23° API gravity crude is obtained from a Jurassic sand referred to as the J-2-A, at an approximate depth of 4,500 feet. Reservoir studies and fluid analyses revealed that the crude is highly undersaturated, having a solution GOR of approximately 130 cubic feet of gas per barrel, that the reservoir has no definable water table, and that it appears to be of a closed-boundary type. Oil production was marked by a rapid pressure decline and it was soon evident that the greatest ultimate recovery would be best obtained if the natural driving energy of the reservoir were augmented by some artificial energy source. In support of a pressure maintenance programme, studies were conducted on flood-pot recoveries of large-diameter cores, and a potentiometric model study of the field was made. These studies indicated that a successful water flood would be obtained. The Dollard field was unitized in 1955 and pressure maintenance started in March 1956."

Jan 1, 1959

By Peter Harben

"This paper discusses the benefits of industrial minerals, their sources of supply, price and marketing trends, and their increasing use as substitute materials and ""strategic"" minerals. IntroductionKaolin finds have yet to spark the kind of frenzy associated with the 1849 California gold rush; no dolomite deposit has ever gained the notoriety of the Comstock Lode; and few industrial minerals are counted among the currently fashionable list of "" strategic mineral s"". Nevertheless, the glamorous zhine associated with metals may be somewhat superficial; further digging provides perhaps the real foundation of modern society - industrial minerals.They are often tagged as common, everyday materials that are simply dug out of the ground, crushed and hauled to a local point of consumption. Although this description is accurate in the case of road aggregates, sand and gravel, and the like, there are many exceptions to this rule. The term industrial minerals is rather nebulous, covering as it does the mundane and esoteric, the chemically active and the refractory, the $2 and the $10m-a-ton product. All of these minerals influence every facet of modern life from fertilizers to fire retardants, ceramics to cars, construction to clothes, and toothpaste to tennis courts. Their usefulness is well illustrated by the variety of industries they serve; the main ones are listed in Table 1. It is now time to dismiss the notion of non-metallics as the ""third world"" of natural resources business after the metallic and energy products by dispelling some of the myths regarding abundance, variety and value of the group's sixty-plus products."

Jan 1, 1982

By R. L. Guerguerian, Eugene Bercel

"Grinding mill hydrostatic trunnion bearings require an external pumping source to provide and maintain the oil film between the bearing members. In order to guarantee a predetermined minimum film thickness, the lubrication system tends to be oversized. The oil film is ""indirectly"" controlled by flow, pressure and temperature monitors with fixed settings on the conservative side. This can lead to excessive maintenance and abbreviated life for the lubrication system components. A reliable method of monitoring actual film thickness would not only provide greater mill availability, but also minimize maintenance costs.This paper describes the instrumentation installed in Dominion hydrostatic bearings, and presents results of field tests where the output of that instrumentation was recorded under various operating conditions.IntroductionThe trend toward larger and more sophisticated grinding mills has made the operators of these machines increasingly vulnerable to financial loss, as the cost of downtime and repairs has increased directly with machine size. In order to guard against such losses, it is becoming imperative that large, sophisticated grinding mills be equipped with protective instrumentation to monitor some of the critical operating parameters and to identify events and trends which, if they go unnoticed, can lead to excessive maintenance costs and machine downtime. The idea of protective monitoring systems is not new. The operators of certain types of machinery where a high degree of safety is required or where machinery health can deteriorate very rapidly, as in the case of high-speed turbo-machinery, have long been using protective instrumentation on their machines. The increased awareness of the benefits of monitoring machinery conditions and the availability of reliable and relatively low-cost instrumentation of a large range of sophistication is making the practice now widespread. Traditionally, grinding mills have not been considered as high-risk machinery requiring instrumented protection. However, the trend, mentioned earlier, toward employing fewer, but larger capacity, mills increases the risk of significant disruption of production, and therefore measures to minimize the risks are desirable."

Jan 1, 1981

By Joseph H. Harris

Shebandowan Mine presents a unique opportunity for the mining industry to demonstrate its willingness and ability to use electrical energy effectively. The mine is a typical 250D-ton/day operation supplied by a i5-MVA power transformer. it is a recent, up-to-date design and operates on a four-day/week, two-shift/day basis. The paper outlines an energy profile based on historical data. It accurately describes the individual and total energy input For: (1) production and non-productive junctions; (2) production and down-time periods; (3) peak and average activity levels; and (4) principal energy utilization equipment. A comparison is then made of production data to electrical data, and production and electrical data to design data. The paper concludes that energy management has an important benefit for the mining industry by assisting in maintaining a competitive operation through reduced costs and fewer production slow-downs in the event of energy shortages.

Jan 1, 1979