Search Documents

By P. Lauzon, C. Oprea, S. Zhou, G. Oprea, J. Rigby, T. Troczynski

Hydration of basic refractories could occur during storage, drying after installation or in use. In order to assess the hydration resistance of various commercially available magnesia-chrome bricks, hydration tests were performed in steam at 110, 120, 130 and 150°C. The changes of the modulus of elasticity by the impulse excitation method, apparent porosity, air permeability, average pore size and pore size distribution were correlated with the hydration data. Mineralogical and microstructural changes were also studied on selected specimens by XRD and SEM/EDS. The hydration mechanisms were discussed in correlation with the chemical and mineralogical compositions of the experimental bricks, in particular with the nature of the mineralogical phases at the grain boundaries.

Jan 1, 2004

By M. Kawahara, H. Sunayama

Oxidation rates of the cubic specimens, which were prepared by cutting the shaped magnesia-carbon bricks, were measured continuously with a thermo balance in the temperature range from 1273 to 1 823 K in N2-02 and Ar-02 mixed gas with 2.1 x 104 and 3.7x 102 Pa of oxygen partial pressure respectively. The effect of the graphite content, the maximum grain size of magnesia clinker and the oxygen concentration in the atmospheric gas on the oxidation rate for the MgO-C refractory has been investigated. The value of effective diffusion coefficient of O2, which diffuses through the porous decarburized layer, decreased with the decreasing of the porosity and the oxygen concentration in the external gas phase. It was speculated that the dense layer formed easily due to the high tortuosity of pores and the low recession speed of the carbon interface in the MgO-C bricks.

Jan 1, 2004

By R. D. MacEchern, M. C. Rockwell

"This paper describes the research and tests carried out to recover the readily available barite from the tailings produced by the Nystone Chemical Ltd. operation at Debert, N.S. The tailings comprised 70-80% of the original feed and contained about 20-25% Baso4 .The objective of the research, undertaken during 1982, was to produce a barite concentrate which would meet the American Petroleum Institute (API) barite requirements for use in drilling mud. Samples from the tailings pond were examined and analysed to determine the tailings characteristics.Preliminary test work was performed on the tailings samples using a Haultain Superpanner, Wilfley tables and Humphrey's spirals. The grade of the barite concentrate retrieved did not satisfy the API barite requirements.The fineness of the tailings and the fact that approximately 80% of the barite was contained in the -200 mesh (0.074 mm) size fractions, indicated that flotation of barite from the tailings might be successful."

Jan 1, 1984

By V. C. Pandolfelli, P. Bonadia, F. A. O. Valenzuela, L. R. Bittencourt

Refractories for aluminum cells, if not properly selected, can lead to increased energy consumption and even shorten the pot life. Based on recent advances in understanding the deterioration mechanism of cathode materials, several commercial bricks in the SiO2-Al2O3 system were compared to the one used by an Alcoa smelter. Both physical and chemical properties were considered in the selection of the refractories. A more reliable method of permeability measurement, which takes into account inertial and viscous effects during the fluid flow, was applied. Additionally, the traditional cup test and other characterization techniques, such as thermal conductivity, X-ray diffraction, and mercury porosimetry, indicated that a brick with a relatively low alumina/silica ratio, presenting low open porosity and low permeability, far exceeded the performance of the brick currently in use.

Jan 1, 2004

"Since all gold mills must sooner or later be cleaned up for permanent shutdown it was felt that a record of what was done at one mill might be of some help to those who will have to do the same job in the future,In cleaning up the mill of Delnite Mines Limited, I had an advantage that most mill superintendents will not have in that I started up the mill and was there until it was shut down, It was also known for two years approximately when the shutdown would be and for a year almost the exact time. This, of course, made careful planning possible and enabled me to get advance information that wouldn't have been available had the shutdown come unexpectedly,Early in 1964 calculation of ore reserves and the known number of working places available indicated that the mine would run out of ore sometime in August or September but not later than October, The time of course would vary with the number of competent miners that could be retained until the shutdown. Since the mining method used exclusively on the ore then remaining was cut and fill, it was known that once mining operations ceased it would require at most two days to crush and grind the last of the ore.In March 1 964 I took samples of the concrete floor under the precipitation presses, in the flux room and furnace room of the refinery and from the assays obtained proved that there would be no profit in breaking up the concrete to recover the gold from it, Samples taken from the top half inch of the concrete floors assayed less than 0, 10 oz per ton,"

Jan 1, 1966

By Zhitong Sui, Feng Zhang, Li Zhang, Tie Ou, Guangqiang Li

Researches on the recovery of iron, manganese and the removal of phosphorus from converter slag were reviewed. The carbon thermal reduction experiments were carried out by induction heating the mixture of converter slag and graphite powders at 1650°C and 1800°C in a graphite crucible. It was found that 62.7% of the phosphorus in converter slag was reduced into carbon saturated iron alloy, 32.8% of that was vaporized and only 4.5% of that remained in the final product. Totally 95.5% of the phosphorus in converter slag was removed. Almost all iron and manganese was reduced to form carbon saturated alloy. It was found that the free lime in converter slag can react with carbon to form calcium carbide at 1800°C. The main phases in the reduced converter slag are dicalcium silicate and tricalcium silicate with small amount of calcium carbide.

Jan 1, 2004

By I. S. Laitinen

Outokumpu Technology has recently introduced new technology in both copper electrorefining and electrowinning. This technology includes, among other things, a new permanent cathode (Outokumpu Permanent Cathode) and new busbar technology (Outokumpu Double Contact System). The new technology has already been tested in commercial scale cells. To get a better understanding of the busbar system a multiphysical simulation model of the electrowinning and electrorefining cells was developed. A mathematical model of electrical conduction and heat transfer in a copper electrolysis cell was developed from partial differential equations. The model was expanded to a cell group including seven electrolysis cells connected electrically in series. The model was solved numerically using the finite element method (FEM). Using the model, different intercell busbar systems were simulated. Typical electrical disturbances, like loose contacts between cathodes and the main busbar and short circuits between electrodes, were included in the simulation. The results of the simulation runs with conclusions are presented in this paper.

Jan 1, 2007

By Mostafa Benzaazoua, Bruno Bussière, Jean Lelièvre

De nombreuses opérations mimères exploitent et traitent des minerais sulfurés pour concentrer des métaux precieux (Au, Ag ... ) OU des métaux de base (Cu, Pb, Zn ... ), laissant en fin de parcours des tonnages considérables de résidus plus ou moins générateurs de drainage minier acide (DMA) selon leur contenu en sulfures. De nos jours, Jes restrictions en matière de protection de l'environnement obligent Jes opérateurs miniers a trouver Jes solutions Jes plus efficaces pour préserver Jes sites environnants de la pollution due a l'oxydation des sulfures. Cette oxydation cause une acidification accrue du milieu et une mise en solution des metaux toxiques. L'utilisation des recouvrements multicouches est l'une des solutions Jes plus efficaces pour limiter la pollution liée au DMA mais entraine des coilts de construction qui sont souvent considérés par l'industrie miniere comme prohibitifs. Une façon de rendre cette technologie applicable, d'un point de vue économique, est de désulfurer Jes résidus à l'usine de traitement et d'utiliser la fraction inerte comme composante d'un recouvrernent multicouche. Cette opération de desulfuration peut etre réalisée par flottation non sélective des résidus dans le but d'obtenir d'une part un faible volume de concentré de sulfures qui devra être géré convenablement et d'autre part un rejet non générateur d'acide.

Jan 1, 1998

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By Y. Kocaefe, D. Kocaefe, G. Ergin

Filtration efficiency depends strongly on the wetting of the bed media by aluminum. This project was undertaken to study the wettability of different types of bed media (tabular alumina) using sessile-drop and infiltration techniques. The samples were analyzed using optical microscopy, SEM, and TEM to study the chemical interactions. The results indicate the spinel formation at the interface. This paper presents some of the findings which compares the two methods and gives the results of the analyses on the wetting of alumina by aluminum.

Jan 1, 2004

By W. M. Silva, Bittencourt. L. R. M.

Three newly developed alumino-silicate refractory bricks for use in safety lining of aluminum electrolysis cells were compared to one commonly used bricks for the same application. It was shown that the increase in silica content and decrease in permeability led to a sensitive decrease in cryolite attack. Both parameters are of utmost importance in selecting bricks for these cells. The reasons for this observation were the formation of a more viscous liquid after the reaction between molten cryolite and the brick, and the reduction of the rate of penetration. Moreover, a novel mortar with high silica content was tested and has shown improved resistance to molten cryolite. The use of oxidizing atmosphere led to increased attack rate in the brick when compared to reducing condition. The opposite effect was observed in the mortars.

Jan 1, 2004

By J. Gao

We present results from our investigation of the concept and practice of using surface-charged latex nanoparticles as building blocks for conductive membranes. Nanoparticles were synthesized by free-radical co-polymerization of two hydrophobic monomers, butyl acrylate (BA) and methyl methacrylate (MMA), a crosslinker, N, N'- methylenebisacrylamide (BIS), and a charged monomer, sulfonate styrene sodium salt (NaSS), in water. The resultant nanospheres were characterized with static and dynamic laser light scattering. Thin films were cast from concentrated particle dispersions, followed by incubation at ?110 °C. Conductivity, water uptake and final charge content were measured. The membranes have higher conductivities than both amorphous films cast from sulfonated BA-MMA-Styrene copolymer chains and BA-BIS-MMA-NaSS gel films. TEM images and neutron scattering spectra confirm the particulate structure of the membranes.

Jan 1, 2005

CFD (Computational Fluid Dynamic) models have been developed and validated for a pulsed column with disk-doughnut internals, as used for solvent extraction. First a single phase model was developed to simulate the turbulent oscillating flow around the internals of the column. This model was successfully validated using detailed PIV measurements of velocity taken at eight different phases through the pulse cycle. Second, the CFD model was extended to allow for a continuous aqueous phase and a dispersed organic phase (kerosene) flowing counter-currently. The model was a two-fluid model that accounts for droplet breakup and coalescence, and solves for droplet size distribution using a population balance model incorporated into the CFX4 package. PDIA (Particle Droplet Image Analysis) measurements were taken on a pilot scale solvent extraction pulsed column to determine droplet size distribution for calibration and validation of the CFD model. The measurements were made under pulsing intensities ranging from 10 mm/s to 32.5 mm/s.

Jan 1, 2007

By Patrick Chabot

Ce document présente une méthode hybride de long trou favorisant une méthode de minage initiale par chambre-magasin et complétée par une méthode de minage long trou. Cette méthode a été adaptée suite à plusieurs facteurs tels qu?une géologie complexe, une rareté de mineur d?expérience et un haut taux de roulement de main d?oeuvre spécialisée. Cette méthode a permis d'excellents résultats par rapport à la dilution. De plus, la récupération de pilier à haute teneur par forage long trou sera expliquée. Cette méthode permet aussi de récupérer le minerai qui est resté accroché dans les chantiers chambre-magasins. Introduction : La mine Géant Dormant est une mine filonienne d?or située à environ 80km au nord de la ville d?Amos au Québec. Elle est en opération depuis 1988 et à la fin de 2007, elle a produit près de 885 000 onces d?or à partir d?environ 2 400 000 tonnes de minerai pour une teneur moyenne d?environ 11,5g /t Au. Cette mine est la propriété d?IAMGOLD Corporation depuis l?acquisition de Cambior par cette dernière au mois de novembre 2006. Elle emploie 151 employés permanents et environ 41 entrepreneurs.

Feb 1, 2008

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004

By Yongqiang Liu

Background For refractory gold ores with high carbonate contents ! Acid pressure oxidation ! High acid consumption (if low sulfur content) ! Low oxidation efficiency due to CO2 in autoclave ! Problems with slimy precipitates (gypsum, etc.) ! Alkaline pressure oxidation ! Difficulty in fixing arsenic ! Low gold dissolution due to iron hydroxides/oxides coating ! High reagent costs Summary ! Carbonate and sulfide minerals had similar floatability across the pH range tested (5 - 12) using sodium oleate as a collector; ! Thioglycollic acid or citric acid depressed the flotation of pyrite but could not depress chalcopyrite when used alone; ! Combination of thioglycollic acid and citric acid had a much stronger depressive effect, and the mixture depressed chalcopyrite as well as pyrite between pH 8 and 11 without affecting the flotation of calcite and dolomite; ! Calcite could be separated from chalcopyrite and pyrite; dolomite could be separated from pyrite but not from chalcopyrite under the tested conditions.

Apr 1, 2005

By J. W. Keyes

"The original grinding circuit at East Malartic consisted of two 8 by 8 C.A.C. mills in closed circuit with two 72 inch Akins Classifiers and an 8 by 10 secondary mill in closed circuit with two 48 inch duplex classifiers. With this circuit, we experienced a drastic drop in tonnage from one month to another, due to variations in the hardness of the ore. The first step to overcome this difficulty was made by increasing the critical speeds of the mills from 78% to 82%. This resulted in an increase in the secondary mill throughput; but, when the change was made on the primary mills no increase was obtained.The drastic drops in tonnage were still experienced and through working with Allis Chalmers the 8 by 10 mill was converted to a rod mill and the two 8 by 8 n1ills to secondary mills. This change eliminated the two 72 inch Atkins classifiers and the scoops on all the mills, since the 48 inch Akins classifiers sands could then be fed by gravity to the secondary mills through feed pipes.The rod mill and secondary mill discharges were fed to a common pump box using 5 by 5 S.R.L.'s running at 1085 R.P.M. with a twenty-five foot head. When this was done the pumping costs jumped from $105. 00 for 6 months to $1050. 00 in one month, or from 0. 0004 to 2. 75 cents a ton milled. Several factors contributed to this jump in pumping costs as follows:"

Jan 1, 1964

By S. M. Taghavi, M. Halali

This paper investigates the possibility of zinc oxide production from zinc ore concentration residues, and also the effect of temperature, time and depth of bed on waste materials reduction percents. The results obtained show a significant increase of the reduction percent as a function of time and temperature. With increasing in depth of bed, reduction percent will decrease. Maximum zinc oxide percent in products was 93.5%.

Jan 1, 2004

By B. Huffman

This paper examines several new trends in the design and application of linings for copper melting shaft furnaces including the use of large shapes, monolithic back-up linings and improved refractory engineering to significantly reduce refractory installation time, diamond saw blade costs, fuel and down-time. The net results are shown to be dramatically increased refractory service life, reusable safety linings, elimination of hot spots and lower refractory disposal costs.

Jan 1, 2007

By Pierre Laliberté

Objectifs ?Quantifier les économies d?énergie potentielles liées àl?utilisation de différentes technologies ?Créer un modèle permettant d?évaluer les économies possibles d?énergie en combinant plusieurs technologies ?On ne peut simplement additionner les pourcentages d?économie individuels pour en évaluer le total.

Feb 1, 2008