Search Documents

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms's method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By Guan Jichang

An abandened breakwater, located at the rear of No. 2 berth in Dongdu Port area of Xiamen City, was not cleaned thoroughly when the backfilling of sand started. The uncleaned stone layer was about 2 to 3 meters deep, with the average piece of stone weighing about 1 to 3 kN. A large grain storing house, 220X 60m2 in area, was designed and built at the above mentioned complicated site. The foundation of the grain house are made up of the cast-in-situ piles. It is well known that it is difficult for the submarine engineering drill to go down through such large-sized stones. Having com-pared the various plans, a final decision has been made which involves explosions with small amounts of charge plus cone bit in the enlarging of the size of the pores. Such a method has successfully prevented the pores from slumping and made it possible to fulfill the project without any difficulties. This paper also introduces the ways in effectively dealing with each individual stone.

Jan 1, 1991

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2005

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By J. Hartikainen

Kemi cardboard mill is founded on the alluvial bed of Kemi river at the north-eastern cost of Botnic Culf in Northern Finland. The alluvium consists of sandy and silty layers underlain by thick medium dense silty moraine layer. The first cardboard machine, having a belt width of 7,4 m, was constructed in 1972 on 7,5 to 9,5 m long wedge-shaped precast driven piles. Because of the excessive differential settlements and sometimes unexpected dynamic malfunctioning of the machine it was decided to strengthen the foundation before installing the partly new machine and increasing the running speed from 500 to 750 m/min. Piling was done under extremly strick limitations concerning space, vibrations, settlements, dust etc. Extra vertical support was made by using 23...25 long x-form steel piles driven by compressed air pile hammer down to rock. The piles were held together with old piles by a conctrete frame with diagonals, which made the total system - machine - foundation frame, piles and ground - ridgid enough to avoid resonance during dynamic loading.

Jan 1, 2010

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Bengt Fellenius

The conventional wave equation analysis without control of the representativeness of the parameters to the actual conditions does not provide accurate results. However, the representatives can be vastly improved by means of using the results of monitoring the dynamic response in a pile during driving. Dynamic monitoring displays the interaction of independent strain and acceleration measurements having directly propor­tional response to impacts, but inversely proportional response to re­flections from the soil. Examples are given and the CAPWAP method used to calculate from the measurements the dynamic pile and soil para­meters and mobilized soil resistance is outlined. The dynamic monitoring technique and analysis has been accepted internationally and been incor­porated into Building Codes. The prediction is offered that in five year's time, no major piling project will be undertaken without dynamic monitoring and analysis.

Jan 1, 1984

By Nikolaus Schneider

"Abstract: The combination of failure in joints of diaphragm walls and their exposure to water pressure may have far reaching effects ranging from water leakage to the risk of catastrophic loss of stability for the retaining wall and civil structures behind it. Investigations of imperfect joints in diaphragm walls have led to the development and testing of a quality tool to monitor the joint integrity of diaphragm walls during construction. By applying independent mechanical sensors (“joint inspector”) to the steel frame of hydraulic or mechanical grabs, it is now possible to record the surface conditions of exposed primary joints during the construction of secondary panels. This allows for the implementation of corrective action during the construction process should joint quality not indicate a watertight connection to the adjacent panel. The joint inspector, used for different types of stop ends, was tested on a full scale test field at several construction sites. The implementation of this new quality tool drives a new quality standard for deep excavations in inner city areas.General introduction to diaphragm wallsDiaphragm walls are reinforced concrete elements constructed using bentonite slurry to temporarily support an open trench in the ground. They are used in two main fields of application in civil construction, as foundation elements for vertical and horizontal loads (barrettes) and as retaining walls for excavation pits.Particularly for deep excavation pits in inner city areas, diaphragm walls are used as temporary or permanent walls of retaining walls. Alternative retaining wall systems would be secant pile walls, sheet piles or soldier piles, but these have disadvantages in structural strength when compared to diaphragm walls. If the vertical load of existing buildings next to the excavation pit has to be accommodated, the most practical solution can be found using diaphragm walls supported by prestressed anchors, steel struts or slabs."

Jan 1, 2014

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By Harry G. Poulos

Ground movements can arise from a large number of sources and can have a significant effect on nearby piles and deep foundations. The loading of the piles by ground movements is a different mechanism to that arising from direct applied loading to the pile head, and consequently it is not generally possible to adequately analyze the effects of ground movements simply by applying some type of equivalent loading to the pile head. The main effects of ground movements are the development of additional movements, axial forces and bending moments in the piles, and thus the key design aspects are related to movements and to the structural integrity of the pile. However, the ultimate geotechnical load carrying capacity is generally not affected by the ground movements themselves. This paper will describe an approach to the analysis of ground movement effects on piles, considering axial and lateral movements separately. Some of the main features of pile response will be discussed for three specific problems involving ground movements: 1. Piles near and within embankments; 2. Piles near an excavation for a pile cap; 3. Piles subjected to seismic ground motions.

Jan 1, 2007