Search Documents

By N. Raeis Hosseiny, S. H. Bassir

"Chador-Malu iron ore is one of the most important iron mines of Iran.About 98 percent of Fe in the ore is in shape of Magnetite, Hematite, Martite, aqua oxide of Iron and the other irons are with ferrous silicates, actinolite, cholorite and ferrous dolomites. 1% of Fe has replaced in pyrite. The phosphor distribution in the ore is non-hemogenous and its average in the whole of the deposit is 94%. It is in shape of Apatite.This mine contains considerable phosphor, which makes it useless for metallurgical uses. At this mine the phosphor is reduced in the iron ore at two steps. At the first step, magnetic part of the ore is separated from the gangues and phosphors by magnetic separator. At the second step, the ore is enriched by the flotation methods. Experimental flotation methods to obtain the optimum conditions are as follows:• Effect of Starch as Hematite depressant with ATRAC as Apatite collector• Effect of Sodium silicate as Hematite depressant with ATRAC as Apatite collector• Effect of ASAM as Apatite collector with Sodium silicate as Hematite depressant• Effect of ATRAC (BEROL) as Apatite collector with Sodium silicate as Hematite depressant• Effect of ASAM & ATRAC mixture as Apatite collector with Sodium silicate as Hematite depressant• Effect of Kcarbonate as pH-modifier• Final test to Optimize pH, Collector, DepressantAt this research we have found the optimum circumstance of the flotation of Chador-Malu iron ore in order to decreasing phosphors of iron oxide and floating of Apatite to make pure Hematite.To reach the optimum conditions, some tests were done with different amounts of pH, collector and depressant. The results are as follows:"

Jan 1, 2003

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Only grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own.CONCLUSION• Overflow versus grate dischargeAn overflow mill has a “pool” of slurry around the toe of the ball charge, which creates a counter lever to the ball charge. This will reduce the absorbed power in the range of 10-15% (depending on the case) and will consequently result in a coarser grind. The tests found a 4% gain in grinding efficiency (Wio) with an overflow mill but this is probably not significant.This lower absorbed power and coarser grind can be counteracted by increasing the ball charge (if below maximum) and/or by increasing the mill volume when removing the grate discharge (a typical grate takes up about 300mm of the mill length).• Open versus closed circuit"

Jan 1, 2003

By Yang Zhao, Tao Xiu-xiang, Chen Song-jiang

"China is rich in low-rank coals that account for 45.68% of existing coal reserves in China. The clean and efficient utilization of low rank coals is of great significance for ensuring the effective energy supply and promoting economic development and environmental protection. In order to solve the difficult problem in flotation of low rank coal, it has become the focus of research in the related field that oily bubbles instead of air bubbles are taken as a carrier in flotation to improve the attachment efficiency and recovery of low rank coal. In this paper, low rank coal slime collected from Shendong mining area was used as the experimental material, and it focused on the characteristics of oily-bubble flotation process of low rank coal. Additionally, difference in conventional flotation and oily-bubble flotation was discussed. The induction time between air bubbles, oily-bubbles and fine low rank coal particles was measured. The results indicated that the induction time between oily-bubbles and coal particles was obviously lower than that of air bubbles. By comparing the foam height of air and oily bubbles, it was found that the amount of oily bubbles is less than air bubbles, causing relative low flotation rate of oily-bubble flotation at initial stage. Besides, the maximum foam height and half-life of air bubbles and oily-bubbles were measured respectively. The results showed that the stability of oily-bubbles was higher than that of air bubbles, which is benefit for the enrichment of concentrates. The clean coal water recovery of oily-bubble flotation is lower than that of air bubble flotation, which indicated oily-bubble flotation is lower in water entrainment. INTRODUCTION China is the largest energy consumer in the world, accounting for 23% of global energy consumption in 2016 and 27% of global energy consumption growth. Whereas coal is taken as the major primary energy source and its share of China’s primary energy consumption is 62% in 2016, in which the low rank coals, such as lignite, long-flame coal, weakly caking coal, and non-caking coal, accounted for about 50% of total coal production capacity (China’s energy market in 2016, BP). Moreover, the exploitation and utilization of low rank coals and other coals that are difficult to float have been an important strategy for China’s sustainable development of the coal industry (Liu et al., 2014). However, the combustion of low-quality coals leads to a serious environmental pollution. In addition, the deterioration in geological conditions of coal resources, and the increasing improvement in the mechanization for mining significantly caused the increased amount of fine coal."

Jan 1, 2018

By Peter M. Solozhenkin

Considering the main idea of the paper, namely that the interaction energy of reagents serves as a criterion used for their selection, as well as due to their insufficient study, the authors have therefore considered studying the aspects of computer modelling and molecular dynamics of largely used collectors for the flotation of nonferrous and precious metal ores. Three-dimensional molecular models for sulphydric reagents have been created, studying as well the distribution of the partial charges on their atoms. It has been shown that the value of the partial charge on the phosphorus atom in diethyldithiophosphinate and diethylmonothiophosphinate is high positive. The value of the partial charge of the sulphur atom is negative, strengthening its bond with the metal cations from the mineral surface. The molecular orbitals for the sulphydric reagents have been created determining as well the energy of their level. The computer modelling key parameters have therefore been defined. The new reagents have been tested for gold, copper and rhenium ore flotation. Gold recovery has increased with 4.2 - 4.7 %, copper recovery with 3.3 % and rhenium recovery with 15.5 %. A number of new flotation reagents have been recommended, such as: diethyldithiophosphate, (C2H5)2NCH2CH2OC(S)SNa, (C4H9NH)2P (S)SNa and also (C2H5)2P(S)ONa and (C2H5)2 P(O)S Na. Keywords: flotation, molecular modeling, design, orbital?s

Sep 1, 2012

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Industrial minerals may contain the same elements in approximately the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques.• quantitative measurements by ebsdCommon automatic techniques describing the mineral contents and the occurrence of minerals in free and locked particles, are based on optical-, backscattered electron (BSE)- or X-ray-signals. There are various commercial software systems on feature analysis by backscattered and X-ray signals in combination with image analysis (e.g. Oxford Inca Feature, CSIRO QemScan).Especially in silicates, the occurrence of similar elements in the different minerals is common. Sometimes the various minerals not only contain the same elements, but also approximately the same amount of each element. In these cases BSE imaging and chemical analysis are not always sufficient for identification."

Jan 1, 2003

By Tiago de Souza, Caroline Gonçalves, Carlos Eduardo de Castro, Everton Dias

The Miraí plant from Votorantim Metais, has two screening stages to the bauxite classification after scrubbagem. The final product has hold the larger size of 0,84 millimeters (20 mesh). There are two sieves Haver & Boecker (model R-TE 3658 x 10972), which have four modules with cut size sieves of 10 mesh (1.70 millimeters) and ¼ inch (6.35 millimeters) on the primary screen, and 20 mesh (0.84 mm) on the secondary screen, all made of polyurethane. The actual configuration was established according to the empirical tests realized that aimed the increase material load on the secondary screening. However, having in mind the screening process improvement and use the fractions smaller than 0,84 mm, which have significant levels of Alumina and low reactive silica, was proposed a new test of change the sieves opening for 6 mesh in the primary screen and 28 mesh for the secondary sieve. The objective of this work was measure the ore alterations on the particle size distribution on the screening steps, increasing the plant weight and ratio recovery before and after the test.

Jan 1, 2014

By B. K. Saikia

A preliminary attempt has been made to study the particle size distribution (PSD) of minerals in one of the industrially important pulverized Indian coal sample using computer-controlled scanning electron microscopy (CCSEM). The results show that clay minerals, quartz, pyrite, and pyrrhotite form the bulk of the mineral matter. Minor minerals, such as calcite, dolomite, ankerite, barite, oxidized pyrrhotite, and gypsum are also observed in the coal sample. The PSD of the included minerals is generally observed to be finer than that of the excluded ones in the coal. Thus, the coal rich in included minerals has more small mineral particles, which may affect its reactivity. The proportion of included to excluded is found to be higher in major cases. Si is found to be mostly occurred as quartz and clay minerals, while Al mostly occurs as silicate minerals. Fe is primarily present as iron sulfides, iron oxide, and Fe-Al-silicate. S is partitioned into iron sulfides and gypsum. Most Ca occurs as carbonates and gypsum, with a minor fraction associated with clay minerals. Mg is found to be mainly present as dolomite and clay minerals, with a very minor fraction present as ankerite. The majority of alkali elements are associated with aluminosilicates. P is mostly associated with kaolinite and/or present as more complex compounds containing Al, Si, and other elements as apatite are found to be absent in the coal studied. Ti is mainly present as rutile and kaolinite. The geo-chemical association of the trace elements has also been discussed. Keywords: minerals, Assam coals, Indian coals, CCSEM study

Sep 1, 2012

By Tuan V. Nguyen, Kosta Simic, Louis Mittoni, Murray Rudman, Jean D. Swift, John B. Farrow, Phillip D. Fawell

"Research projects towards developing a sound understanding of the factors controlling the performance of gravity thickeners have been conducted by the AJ Parker Cooperative Research Centre for Hydrometallurgy since 1988 through AMIRA International. The current phase of this work, the three year P266D .Improving Thickener Technology. project, has 27 sponsors comprising mineral processing companies, reagent suppliers and thickener manufacturers.These projects have resulted in the development of a range of tools and techniques to address flocculation, thickening and associated dewatering issues. A number of Computational Fluid Dynamics (CFD) models have been developed to predict likely full-scale thickener performance under various process conditions, based upon a knowledge of thickener design, plant flows and assessment of the flocculation behaviour of the feed slurry. At the same time, various laboratory and plant studies have been used to quantify important thickener processes, and to provide validation of the CFD models. These numerical and experimental capabilities have been applied to various thickener issues across a broad range of mineral processing operations, leading to significant process improvements and substantial financial benefits.This paper presents an overview of the work conducted during these projects, focussing on the research tools, the nature of the information that has been gained and the implications for thickener performance."

Jan 1, 2003

By Liu Xinghua

Yuanjiacun iron ore located in Shanxi province of China has finely disseminated grain size and contains refractory iron-bearing silicate gangue minerals such as chlorite. Therefore, a large amount of secondary slime (the content of -10µm fraction was up to 32.92%) was produced inevitably in fine grinding process, and chlorite was also enriched in concentrate from the content of 4.3% to 14.8% after high intensity magnetic separation. These two characteristics result in the difficulty to deal with Yuanjiacun iron ore by flotation. In this test work, contrast tests between single reverse flotation and selective flocculation desliming-reverse flotation were conducted on Yuanjiacun iron ore. The test results show that after selective flocculation desliming, the iron grade of cationic reverse flotation concentrate increases by 6.15% and the recovery increases by 7.25%; the iron grade of anionic reverse flotation concentrate also increases by 2.15%. Furthermore, analyses of grain size composition and mineral composition were carried out on separation products, the results indicate that selective flocculation desliming plays a dual role of optimizing grain size composition of flotation feed and removing iron-bearing silicate gangue minerals (chlorite) effectively.

Sep 1, 2012

By C. V. G. K. Murty

Sillimanite, chemically named Aluminum silicate, 3Al2O3SiO2 is one of the three forms of alumino silicate polymorphs and commonly encountered in aluminous metamorphic, plutonic, and volcanic rocks and their weathering products. Most of the sillimanite deposits are granular and are of high grade available in coastal areas as associated mineral along with Titanium bearing minerals namely ilmenite, rutile etc. Sillimanite is one of the widely accepted raw materials for the manufacture of high alumina refractories (55-60 % alumina) or bricks. Sillimanite based refractory bricks are used for the lining of Blast furnaces, Arc furnaces, Soaking pits, Reheating furnaces of iron and steel, rotary kilns for cement manufacturing and general kilns for lime production. Considering the vast potential of unexploited sillimanite reserves in India, M/s Trimex Sands Pvt. Ltd., (TSPL)has set up a Mineral Sand Processing plant in 2010 at Andhra Pradesh with a capacity to produce about 50,000 tons of sillimanite per annum besides the production of various heavy minerals such as ilmenite, rutile, zircon and garnet. Traditionally in India, sillimanite is upgraded by froth flotation technique using Oleic acid as a collector cum frother, sodium silicate as depressant and soda ash as pH regulator. At TSPL, Conventional mechanical float cells are installed to float sillimanite. In addition to the usual problems associated with conventional cells, poor flow ability of the sillimanite concentrate is experienced in dry circuit due to the presence of sodium oleate. Fine garnet in the sillimanite concentrate contributes to high iron content in the final product, making sillimanite separation a nightmare for operators (lower recoveries coupled with inferior grades). Various efforts were made to improve the performance of the circuit such as introduction of additional frother like MIBC, optimizing the operating parameters such as pulp density, collector dosage, depressant dosage, air flow rate, pH etc., use of collector aids, stage wise addition of reagents etc. The challenges faced to produce a sillimanite product with stringent quality norms and the efforts made to improve the grade and recovery are described in this paper. Keywords: sillimanite, froth flotation, conventional mechanical cell

Sep 1, 2012

By P. Harris

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:• flotation tailings of crystalline graphite minerals• outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers."

Jan 1, 2003

By H. Pearce, A. E. Lewis, A. Ochieng

Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. The computational fluid dynamics (CFD) technique has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the pitched blade impeller have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor.

Jan 1, 2003

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of rgrinding conditions on galena flotation and galena separation from pyrite. The various reactions occurring on the mineral surface were investigated by a range of techniques, including OH- addition to maintain the grinding pH, EDTA extraction, XPS and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the metal oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite but had little effect on galena. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled."

Jan 1, 2003

By Kyle Bartholomew, Robert McIvor

"Functional performance analysis of closed circuit grinding provides valuable insight into the two components of ball mill circuit grinding efficiency: classification system efficiency and mill grinding efficiency. Classification system efficiency isolates the combined effect of classifier performance and circulating load ratio from other circuit variables, such as ore grindability and the mill grinding environment. Optimization of classification system efficiency ensures grinding energy is applied to particles needing further size reduction and not to overgrinding. Entirely based on size distribution data, classification system efficiency precisely distinguishes subtle changes in classification system performance. Use of the functional performance equation to isolate mill grinding efficiency allows for proper optimization of the mill grinding environment by isolating confounding effects of changes in classification and ore grindability. Variables such as mill percent solids and grinding media selection can be optimized using the mill grinding efficiency subcomponent of functional performance. First published by McIvor in 1988, the functional performance equation provides a set of standardized, quantitative optimization criteria, simple and powerful, which link circuit performance to plant design and operating variables that can be manipulated. Functional performance optimization has been applied in numerous mineral processing plants globally and continues to gain acceptance as a practical means for grinding circuit optimization. In this paper, examples of derivation and industrial application demonstrate the means by which functional performance analysis dissects grinding circuit efficiency into its subcomponents allowing the reader to apply this straightforward, powerful optimization methodology at their mineral processing operation."

Jan 1, 2014

By Arkady Senchenko

At present, there are different traditional and modern methods for ore grindability evaluation. The correct and rational approach to sampling, testing methods and mill sizing enables one to design a workable technology. This paper contains TOMS institute experience in different grinding indices determination over the last 7 years (SAG Design Test, BWi, CWi, RWi, and other). Mill sizing examples and circuits modeling for the projects in Russia and Kazakhstan are considered. Keywords: ore grindability, SAG Design Test

Sep 1, 2012

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"A gold has been leached with ammonium thiosulfate solution and several leaching conditions have been studied. The leached solution has been recovered by solvent extraction and the optimum conditions have been investigated.SUMMARYIn this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 – 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 – 3.0x103 mol/m3 NH4OH, 0.4 – 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration."

Jan 1, 2003

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By R. Roufail

In this paper, the effect of different operating parameters of high speed stirred mill on the particle breakage mode is addressed. Morphological features of broken particles is investigated and related to the types of forces generated in the mill using Discrete Element Method (DEM). The stress intensities generated in the mill are varied by changing the agitator speed. The investigated agitator speeds were 1000, 1500, and 2000 revolution per minute (rpm). The minerals considered in this study are hard minerals (quartz) and soft, sulphide minerals (galena). The morphological features examined are roughness, roundness and elongation, which shed light on the mode of breakage during the grinding process. Particles that are rough, less round and elongated would imply that they broke via fracture, along their grain boundaries. On the other hand, the smooth, less elongated particles would mean breakage occurred across the grain, which is abrasion mod. DEM study complemented the understanding of particle breakage mechanism via tracking the types of forces applied on the particles. Normal forces imply compressive loading, which is presumed to impose fracture breakage along the grain boundaries, whereas tangential forces imply abrasion loading. Stirred mill grinding has been regarded as an attrition/abrasion process, whereas, this study showed that about 60% of total particles that are morphologically analyzed for both minerals were rough particles. Such an observation indicates that the fine product, which contain a significant amount of progeny from the coarse fractions are consistently broken via fracture. The morphology results agreed with the DEM findings, which indicated that the agitator speed, mineral type, and residence time would dictate the type and mode of particle breakage. Keywords: DEM, high speed stirred mill

Sep 1, 2012

By Gi-Chun Han, Ki-Suk Han, Korea Energy Management Corp., Jin-Sang Cho, Hyung-Seok Kim, Jae-Hyun Oh

This study has been carried out to use the waste sludges generated at Pohang Iron & Steel Co. Ltd. (POSCO) as the raw materials of Ordinary Portland Cement (OPC). The burnability index of the raw mixture and the hydration characteristics and compressive strength of clinker have been examined. The waste sludges were mainly composed of CaO, SiO2, Al2O3, and Fe2O3, the main component of OPC. The Burnability index of mixture was improved, according to the replacement content of POSCO sludge increase. POSCO sludge can be used as a raw material for cement because the state of mineral development and property of clinker produced from POSCO sludge are similar to the plain. Therefore, POSCO sludges can be used as the source materials of iron and calcium oxide.

Jan 1, 2003