Search Documents

By Dezhou Wei, Cong Han, Shuling Gao, Wengang Liu, Yanbai Shen

The recycling schemes of copper mineral to a copper raw ore produced in China is investigated in this paper, of which is aimed at copper concentrate‘s grade is over 26.00% and recovery is over 90.00%. The primary copper mineral the raw ore is chalcopyrite and the main gangue minerals are quartz, orthoclase, albite, clinochlore and phlogopite. There are four useful metal elements contained in the copper raw ore, which are Cu, Pb, Zn, Au and Ag, and the grade of each is 3.75%, 0.01%, 0.11%, 0.31 and 483.5 g/t. Two floating recycling schemes and its corresponding flotation reagent system were determined. The results show that calcium oxide, sodium carbonate and sodium sulphide were used as regulators, sodium n-butylxanthate was used as collector and terpenic oil was used as frother in two floating recycling schemes are effective. The open-circuit test’s results show that the copper mineral contained in raw ore can be effective collected, and both concentrates gotten through two schemes are up to grade.

Jan 1, 2014

By S. K. Pan

The process flow-sheet adopted in treating hematite iron ore in India through wet circuit generates not only 15-25% slime of Run-of-Mine (ROM), but also results in loss of very high quality fine iron ore particles along with it. As the reserves of hematite iron ore is depleting, it is necessary to explore the possibility of upgrading other types of low grade iron ore and slime for recovery of iron minerals; extensive research in this field is being carried out. While beneficiation of low grade ore is yet to be established, slime beneficiation has been quite successful and many installations of slime treatment plant are underway. In SAIL mines, the slime is mainly the discarded particles from Classifiers, which are less than 0.2 mm sizes. R& D initiative has been focussed on the beneficiation of the slimes (49-60% Fe, 3-10% Al2O3 & 4-10% SiO2) of Dalli mines to generate concentrates assaying 62-64% Fe, 2-3% Al2O3, 3-4% SiO2 and a few innovative facilities for the same has been introduced at this mines of Bhilai Steel Plant (BSP). At Dalli mines, the slime is of very poor quality. A typical slime analysis assays 48.54% Fe, 15.1% SiO2, 8.5% Al2O3 and consists nearly 60% (by wt.) particles less than 38 micron. Slime analysis revealed substantial quantity of very high density mineral particles, those causes jamming of Thickener due to faster settling. A novel technique has been implemented to classify the concentrate ore particles from the gangue mineral particles by processing through Fluidized Bed Classifier (FBC) system, which is a gravity concentrator, to treat 50% of the slime generated and the rest is treated through de-sliming hydro-cyclone followed by Medium Intensity Magnetic Separator (MIMS). A special self-vibrating launder has been designed and introduced into the system to recover tiny iron ore particles, which could not get captured by the permanent Neodymium rare earth magnet in MIMS. The classified iron mineral particles from FBC are further treated in a battery of hydro-cyclones followed by modified Slow Speed Spiral Classifier (SSSC) unit. Multiple feed entry system to the SSSC unit is unique and use of particular feed entry point depends on the desired quality of the product and thus converted to a beneficiation equipment rather than mere de-watering unit. By processing slime in FBC system, the valuable iron ore particles with 62.5% Fe, 5.2% SiO2, 2.23% Al2O3 has been recovered from the slime at a material yield of 30%. And very high valued concentrate particles with more than 65% Fe has been sorted out through the magnetic separation route. The overall extra production of beneficiated slime concentrate is 40-45 tph with 63-64% Fe from a slime feed of 120-130 tph solid. This paper outlines few new approaches in iron ore slime beneficiation at Dalli mines for maximum recovery of valuable minerals. Keywords: fluidized bed classifier (fbc), iron ore slime of dalli mines, medium intensity magnetic separator, slow speed spiral classifier (sssc)

Sep 1, 2012

By Graeme J. Jameson

"When mineral particles are floated in a mechanical flotation cell, it is found that the rate constant, after reaching a maximum value, starts to decline as particle size increases. It had been thought that the reduction in rate constant had been due to the increased prevalence of composite particles in natural ores, for larger particles. However, Jameson (2012) showed that the rate constant for composites is certainly a function of the surface liberation, but the reduction in flotation rate is independent of particle size. Thus all particles are equally affected by reduced surface liberation, independently of their size. He further argued that the classical peak observed in the rate constant with increasing particle size, is a function of machine hydrodynamics. Thus in mechanical cells, the peak may be due to the high energy dissipation rate and its effects on the detachment of particles from bubbles (Goel and Jameson, 2012). Consequently, in a different flotation environment, it may be possible to float large composite particles that cannot be floated in mechanical cells. This paper describes the flotation of large composite particles in a fluidized bed flotation cell. The particles to be floated are fed to a column in which there is a continuous upflow of liquid. A conventional froth layer of controlled depth is formed at the top of the vessel. A fluidized bed of particles is established which provides a gentle environment for the contacting of large particles with bubbles. An example is given where a porphyry copper ore was prepared at a top size of 710 µm, and floated with conventional collector (PAX) and frother (MIBC). The concentrate was separated into size fractions and examined by photography. Composites were observed at all size fractions, but above 400 µm, all particles were composites. The implications for future flotation circuits will be described."

Jan 1, 2014

By M. A. Hampton

The surface oxidation of sulfide minerals in aqueous solutions is an important sub-process in sulfide flotation and hydrometallurgy, but a full understanding of the oxidation process and products is still lacking. Many oxidation pathways and products involving elemental sulfur, metal polysulfide, metal-deficient sulfide and sulfate have been proposed, confirmed and argued. In this paper we provide further insight into the surface electrochemical behaviour of galena in aqueous solutions. For this research we have developed a novel experimental system, that combines chronoamperometry and AC-mode AFM surface imaging, which allows for in-situ, synchronized electrochemical control and examination of oxidative surface morphology. At pH4, the morphology of elemental sulfur (detected by ex-situ Cryo-XPS) formed on the oxidizing galena surface depends on the electrochemical potential pathway. In multi-step chronoamperometry (i.e. four potential steps from 0 mV to + 350 mV) the sulfur forms as nanoscopic domains, whereas in single-step chronoamperometry (i.e. one potential step from 0 mV to + 350 mV) sulfur forms as a heterogeneous layer. In each case the oxidation is controlled so that the number of electrons (coulombs) passed per unit area is the same, therefore the amount of sulfur produced is also the same. The differences in morphology with electrochemical potential pathway are explained using a nucleation and growth model. The formation of sulfur on the surface increased both advancing and receding contact angle of galena, but the morphological changes induced by different electrochemical potential pathways did not significantly alter the hydrophobicity of the surface. Keywords: galena, lead sulfide, oxidation, Atomic Force Microscopy, electrochemistry, collectorless flotation, hydrophobic

Sep 1, 2012

By F. K. Ikumapayi

An approach to environmental sustainability and improved process economy, in sulphide minerals production is recycling of process water in flotation of complex sulphide ores, although the chemistry of process water may be a critical issue to flotation efficiency. The influence of major components of calcium and sulphate ions in process water on xanthate collector adsorption and flotation response using pure chalcopyrite, galena and sphalerite minerals were investigated by Hallimond flotation, zeta-potential measurement, FTIR and XPS spectroscopy studies, while bench scale flotation tests were also carried out using complex sulphide ores. The impact of the species in flotation was comprehended using deionised water, tap water, process water and simulated water containing equivalent amount of calcium and sulphate species in process water. Hallimond flotation results showed a decrease of chalcopyrite and galena recovery in process water and also in the presence of calcium and sulphate ions in both deionised and process waters, whereas sphalerite does not respond to flotation. The adsorption of calcium and metal ions but not sulphate ions on the minerals is evidenced by zeta-potential data. FTIR and XPS studies revealed the presence of surface oxidized sulfoxy species and surface calcium carbonates on chalcopyrite in the presence of process water and water containing calcium ions, surface oxidized sulfoxy and carbonate species on galena in the presence of deionised water, process water and water containing calcium and sulphate ions, all at flotation pH 10.5, and these surface species influenced xanthate adsorption. The presence of surface oxidized sulfoxy and carbonate species at the sphalerite flotation pH 11.5 were seen in the presence of deionised water, process water and water containing calcium and sulphate ions, but the surface species does not influence xanthate adsorption. Bench scale flotation using two different complex sulphide ores showed that chalcopyrite, galena and sphalerite recoveries are better in process water than tap water. The studies showed that the process water can be recycled in flotation with no detrimental effect on grade and recovery of sulphide minerals. Keywords: sulphide minerals, flotation, zeta-potential, FTIR, XPS

Sep 1, 2012

By Ibrahim Alp, Duygu Dinç, Ersin Yazici, Adularya Energy and Electricity Generation and Mining Inc., Oktay Celep, Haci Deveci

Thiosulfate leaching as an environmentally benign alternative to cyanide leaching has received particular attention in recent years. Most studies have focused on thiosulfate leaching of free milling ores and, to some extent, pregrobbing ores. In this study, leaching of gold from the refractory Kaletas ore (in which gold/silver alloy is the only mode of occurrence detected) in ammoniacal thiosulfate solutions was studied. A two-level full factorial design (23) was adopted to investigate the effects of concentration of thiosulfate (0.2-1 M Na2S2O3), ammonia (0.5-1 M NH3) and copper (0.05-0.1 M CuSO4) on the extraction of gold from a ground ore (-38 µm) over a period of 24 h. Statistical analysis confirmed the leaching of gold improved with increasing concentrations of thiosulfate and ammonia. In contrast, increasing the concentration of copper in the range tested adversely affected the extraction of gold. The magnitude of effects of parameters on the gold extraction was in the order of Na2S2O3 > NH3 > CuSO4. The maximum extraction of gold (69.6%) was obtained in the presence of 1 M Na2S2O3, 1 M NH3 and 0.05 M CuSO4. The negative influence of copper on gold extraction is most likely attributed to the decomposition of thiosulfate catalyzed by copper. Concentration of thiosulfate was also identified to be statistically the most important parameter for its consumption.

Jan 1, 2014

By Milind Chikhale, Yogesh Reja, Keshav Tyagi

"Using computer models for process design is a well-established practice in the mineral industry. In recent years, there has been emphasis on modeling of processing plant as a whole. This paper covers development of a model for iron ore processing plant. Basic purpose of this model is to use simulation for efficient plant design and help in minimizing risk at the very initial stage of project. Feed to the plant is Hematite iron ore from a deposit located in Eastern India. Major processes in plant include multi-stage crushing, screening, grinding, classification, gravity and magnetic separation. Models for different process equipment were developed using METSIM and Bruno simulation software. Customized black box models and known mathematical models were used for predicting behaviour of processes. Data needed was identified based on the model type. The required data was arranged as per project requirement and processed for development and validation of model. Equipment models were developed and validated on the basis of process design basis, theoretical and empirical data from technical references, and bench scale and pilot scale testwork results. Validated process circuits were assembled to simulate and represent the entire plant process. The result shows expected variation in plant output as a result of variation in the feed. Study concludes by discussing potential applications of the model in plant design."

Jan 1, 2014

By I. Yu. Rasskazov, A. V. Rasskazova, N. M. Litvinova, N. A. Lavrik, V. G. Kryukov

The possibility of the intensification of the gravity processing of complex iron-manganese ore, which contains the finely dispersed inclusions of gold and platinum is shown. Clear mineral fractions of precious metals were sorted out of the different types of ores (quartz-braunite and carbonate- magnetite ore, ferruginous quartzite, carbon-containing shale, breccia-limestone and dolomite breccia). Composition and structures of precious-metals particles was detailed. The industrial content of platinum and gold was found. Precious-metals mineralization is character for all types of ores. High content of platinum is indicated in the carbonate-magnetite (up to 11.3 mg/kg) and quartz –braunite (up to 10 mg/kg) types of ore. Gold is presented in the ferruginous quartzite (up to 1.29 mg/kg) according to the data of the reduced mineralogical analysis. The composition of native platinum depends on the type of the ores: 1) quartz-braunite type contains isoferroplatinum (Pt3Fe) with Cu, Rh, Ir, Ru; 2) carbonate-magnetite type contains isoferroplatinum with Cu, Sn, Ni, Rh, Ir, Os; 3) pyritic-carbon ore contains isoferroplatinum with Sn, Ni; 4) ferruginous quartzite contains isoferroplatinum without admixtures. The ultrasonic treatment of mineral aggregates (P = 41.5 Watt, I = 15 W/cm2) made possible the liberation of fine particles of precious metals. Smooth-shaped or crystalline mineral aggregates are effectively liberated after acoustic treatment. Their surface is freed from impurities. The aggregates with the complex form and structure, which consist of the numerous plates and the grains, are not effectively liberated from impurities. It is shown that the ultrasonic treatment of aggregates with the fine inclusions of precious metals contributes to the liberation of the particles of platinum and gold and intensification of the gravity processing of refractory ore. This approach contributes the increase of the raw-material base of precious metals.

Jan 1, 2018

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By Kilian Neubert, Hermann Wotruba, Henning Knapp

Sensor-based sorting has been integrated into more and more applications in mineral processing over the past decades. Various sensor types, such as line scan cameras, near infrared sensors and X-ray transmission sensors, allow the separation of a vast variety of raw materials. Sensor-based sorting has several economic benefits which can make the difference between an uneconomic operation and a profitable mine. Sensor-based sorters can be applied to fulfill various sorting tasks, such as waste rejection, product quality improvement and ore type diversion, and have a significant impact on the layout of the processing plant. Therefore, it is important to include sensor-based sorting into the planning of a processing plant at an early stage. To evaluate the applicability of sensor-based sorting for any specific ore type, it is currently necessary to provide several hundred kilograms of material for subsequent bulk tests. In exploration, ore samples are usually rare and only available in form of drill cores. The acquisition of drill cores is time-consuming and expensive especially for deposits in great depth. Hence, it is unfavorable to spoil valuable drill cores for bulk tests. This paper describes a methodology to evaluate the applicability of sensor-based sorting based on drill core analysis. That methodology offers the possibility to calculate the achievable performances of different sensor types for various grain sizes without comminution of drill cores. The general methodology is shown on basis of an exemplary test work on drill cores from a currently conducted exploration.

Jan 1, 2014

By Zhou Yucai, Zhou Jing, Zhu Yimim

"In this article, research on the beneficiation process for a carbon containing copper-molybdenum deposit in Henan province has been carried out. The elemental composition, mineral composition and relative content, characteristics of embedded and symbiotic relationship, the forms of the copper-molybdenum particlesand their disseminated features, and particle size distribution have been worked out. Flotation behavior of copper-molybdenum mixed flotation and separate flotation in the systems of different collectors and depressants, and the influence of different flowsheets on the copper-molybdenum separation have been investigated by actual ore flotation tests, The separation problem of copper-molybdenum for a carbon-containing copper molybdenum ore has been solved.INTRODUCTION In this paper, technological mineralogy, small experiment of flotation recovery of copper Molybdenum ore, and expansion experiment of mineral recovery of copper Molybdenum ore are introduced. (1) The results of process mineralogyshow that the content of copper is 0.42%, molybdenum is 0.021% in the raw ore, they mainly exist in the form of sulfide, with low oxidation rate. (2) The results of flotation tests show that the combination of butyl xanthate and isopropyl ethylthionocarbamate reagents is effective collector of copper-molybdenum mixed flotation for carbon copper molybdenum, (3) When the grinding fineness is -0.074 mm taking 71%, and regrinding fineness is -0.038 mm taking 85%, the flowsheet of first copper-molybdenum mixed flotation and then regrinding rough concentrate and last separation flotation of copper and molybdenum was adopted, which realized the effective separation of copper and molybdenum for carbon-containing copper molybdenum ore. Good flotation indexes were gained with copper concentrate containing 20.96% copper and copper recovery 90.06%, and molybdenum concentrate containing 46.78% molybdenum with molybdenum recovery 72.68%. (4) The seven days average concentration index of scale-up the continuous dressing experiment is as follows, the copper content in copper concentrate is 20.16% and the recovery is 89.61%; the molybdenum content in molybdenum concentrate is 24.58% and the recovery rate is 74.09%."

Jan 1, 2018

By David Dreisinger

"The leaching of base and precious metal ores and concentrates continues to progress in both laboratory study and industrial application. These developments are being driven by the need to respond to difficult ores and concentrates that are not amenable to conventional treatment. In many cases alternatives are being developed to conventional treatment (e.g. Pyrometallurgy) for technical and economic reasons.In this paper, a brief general review of some new developments in leaching will be followed by a more detailed explanation of three process developments that have either been industrially applied or are expected to be applied in a short time frame. The three processes to be reviewed in detail are the Mt. Gordon Copper Process, the Anglo American Corporation/University of British Columbia Copper Process and the PLATSOL Process. These leaching processes operate at low (90°C), medium (150°C) and high (220°C) temperature and are successful in quickly and completely extracting metal values from ores and concentrates."

Jan 1, 2003

By R. Chowdhury

Axis House manufactures and supplies alkylhydroxamate reagent of various carbon chain lengths for application in flotation of oxide copper and other minerals. As part of reagent performance improvement the structural factors of hydroxamate are examined by various analytical tools in particular with X-ray diffraction of single crystals. In a recent publication, the structure of n-octylhydroxamic acid and its corresponding potassium salt are presented with findings of hydroxamic functional group geometric preference, H-bonding, keto-enol tautomerisation, acid-salt aggregation and alignment of carbon chain. In this paper an example of branched alkylhydroxamate 3, 5, 5-trimethylhexylhydroxamate will be presented and compared with the result of linear alkylhydroxamate.

Sep 1, 2012

By Z. H. Wang

The internal parameters of ball mill are very important in the grinding process and have significant impact on the grinding results. Accurate measurement of the internal parameters of ball mill is crucial and indispensable for optimization and control of grinding process. In this paper, a novel tri-sensor measurement method was used to measure the external signals (i.e., bearing pressure, sound intensity and power consumption) of ball mill. Mathematical models, which link the external signals of ball mill with its internal parameters, were established to predict the internal parameters of ball mill. Experimental results showed that the mathematical models could directly predict the internal parameters of ball mill once the external signals were obtained. The tri-sensor measurement method and the mathematical models proposed in this paper provided a new way and solid basis for optimization and control of ball milling.

Jan 1, 2014

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By H. Z. Kuyumcu

Coking of coal blends using high volatile coals with poor coking abilities to produce a high quality coke for blast furnace application can be achieved by compacting the coal blend prior to the carbonization process. Here densification up to a relative material density of 80 %, i.e. a compact density around 1100 kg/m3, has proven to be advantageous. Coal is compacted by stamping, if the so-called stamp charging process applied. Compacting of the coal by pressing is practised in case of the cokemaking with so-called heat-recovery ovens. Stamped and pressed coal cakes require over the cake volume uniform high density and mechanical stability. Besides the aspects of the coal selection, the efficiency of the process is mainly determined by the operating parameters compacting time and compacting energy for coal cake making. At the Department for Mechanical Process Engineering & Solids Processing of the Technical University Berlin the two sub-processes of densification and strengthening during stamping and during pressing are theoretically and experimentally investigated using specially developed lab-scale compacting test units and a strength test device. Describing cake density in terms of coal properties for a given coal and measured compacting energy input then leads to a compacting equation with the so-called Stampability as the integral model parameter for the stamping process. For the pressing process the cake density can be calculated with the measured compacting pressure and the Compressibility factor, respectively. Investigations were carried out to provide evidence of a significant influence of coal type, coal surface moisture, coal granulometric and mechanical properties on the densification process. The overall objective of the work is to establish a comprehensive mathematical model on the compacting behavior of large coal bulk quantities and the optimization of the compacting processes by stamping and by pressing. Keywords: coal compacting, agglomeration, stamping, pressing, cokemaking

Sep 1, 2012

By Lokesh K. Thakur, Peter Radziszewski

"For the cases tested (11 mills with 15 operating conditions), the Bond abrasion test steel media wear rate prediction gives an overall error of 73% and a standard deviation of 192.5%. However, total steel media wear in a given mill (ball or SAG) grinding process is a product of three recognised wear mechanisms -- impact, abrasion, and corrosion. A total media wear model can be defined on the assumption that the effect of each wear mechanism can be independently determined which allows for a total media wear model to be defined as the summation of the wear result of each mechanism (eqn. 1). It is assumed that impact and abrasive media wear is a function of the energy dissipated in impact and abrasion as estimated by a DEM charge motion simulation. Corrosive media wear is assumed to be a function of the media surface area present in a mill.The 3 initial tests developed (steel abrasion wheel, corrosion batch mill, impact chamber) coupled with the impact and abrasion energy spectra from a DEM charge motion simulation produced total steel wear rate results for the same cases as the Bond abrasion test giving an overall error of 0% and a standard deviation of 66.1%. However, if one were to consider the general observation that wear is proportional to energy and maintain the assumption that corrosion is proportional to media surface area then one would realize that the total media wear eqn. (1) can be reduced to eqn. (2). As this is a linear equation and one has, for the same mill, media wear and operating data for three different operating cases, one obtains three equations with three unknowns. This defines a simple matrix manipulation to determine the constants k1, k2 and k3. From the previous data set, we had 6 identical mills grinding the same ore but having different worn liner profiles and charge volume which provided the opportunity to average out the ki values over 20 combinations of 3 cases. With the determined ki values, it was possible to determine a second estimate of the contributions of impact, abrasion and corrosion to total media wear giving an overall error of 0% and a standard deviation of 56%."

Jan 1, 2003

Opportunities to monitor and control primary grinding mill performance are strongly sought after in the mineral processing industry. Currently, limited on-line information about mill charge motion and content is available to mill operations for control purposes, leading to periods of lower throughput, instability, variable product size and accelerated mill liner and lifter wear. In response to this need, CSIRO has developed an on-line surface vibration monitor for primary grinding mills which produces data that has been shown to provide new information about the mill charge in terms of toe and shoulder position, as well as potentially key features such as the overall charge level, the distribution between rock and balls in the mill, and the impact of the charge on the mill liners and lifters. This paper outlines the key features of the on-line monitor system, particularly those relating to data transmission, data analysis, and the design of the monitor and its independent power supply. It describes the coupling of single vibration sensor data from the CSIRO on-line monitor to the actual operating conditions of a SAG mill and how the vibration response and hence mill operating conditions vary as a function of time, including during mill equipment failures such as a broken discharge grate. Opportunities for improved mill control based on the data from the on-line monitor are also discussed, as well as the implications in terms of mill processing and maintenance performance. Recently a CSIRO monitor was also installed on a ROM ball mill and analysis of the vibration sensor data from this installation is currently underway. Preliminary findings from this installation will be presented along with comparisons of generic information, such as toe position (measurement precision and operation variability) and vibration signal (intensity, sensitivity and operation variability), between this type of primary grinding mill and AG/SAG mills.

Sep 1, 2012

By Q. R. Chen

Wet processes are commonly used in coal preparation field home and abroad. Dry coal cleaning technology is very necessary in China because more than 2/3 of coal resources deposited in arid areas, which are difficult to separate coal with wet processes. A particular interest of this article is the discussion of separation research development of dry coal cleaning in China, such as an air dense medium fluidized bed (ADMFB) beneficiation technology, a compound dry (pneumatic) separation technology and a triboelectrostatic separation technology. The fundament and importance of dry coal cleaning methods above were introduced. On the basis of analyzing parameters which influence the performance of separators, including that of structure, technologic and operating, the separation research status of dry coal cleaning methods, especially the ADMFB beneficiation technology, were discussed and reviewed. The recent developments, especially the fluidized bed beneficiation for <6mm fine coal with an external energy assisted, including a vibrated fluidized bed and a magnetically fluidized bed, and the triboelectrostatic separation for <1mm fine coal are also introduced. The study and application results in China show that dry coal cleaning technologies can efficiently beneficiate different coals with different sizes. The ADMFB can separate >6mm coarse coal with an E value of 0.05~0.08, the external energy assisted fluidized bed can separate <6mm fine coal with an E value of 0.07~0.09, the triboelectrostatic technology can efficiently separate <1mm fine coal, and the compound dry separation technology can efficiently separate >3mm coal with a easy washability. The dry coal cleaning provides an efficient and lower cost clean approach for coals distributed in arid areas.

Jan 1, 2014

By C. R. Mambote

One of the processes developed for vanadium recovery from the fly ash of crude oil is through acid leaching. In the process, iron is one of the impurities that should be removed before vanadium precipitation, due to the fact that iron tends to co-precipitate with vanadium. The mechanism of iron precipitation is understood in terms of ferric hydrolysis, followed by the dimerization and subsequent polymerization of the crystalline iron compound. In order to develop a new approach for the fly ash processing, in the present paper the precipitation of iron from the liquor after the leaching process was studied with addition of NaOH or NH4OH in the presence of H2O2 or Na2C2O4 at 80°C. The objective was to investigate the feasibility of the selective precipitation which could be applied to vanadium and nickel recovery from the fly ash. The experimental results show the difficulties of removing iron by precipitation without co-precipitating nickel and vanadium.

Jan 1, 2014