Search Documents

By Avishan Atrafi, Marek Pawlik

"Gas dispersion properties of sodium salts of 6, 12 and 18-carbon fatty acids (hexanoic, lauric and oleic acid) were investigated as a function of pH. A strong effect of pH was observed on gas dispersion properties of fatty acids. At high pH for 12 and 18 carbon fatty acids, at which these surfactants formed a true solution, the gas dispersion properties were similar to those of MIBC. In the case of sodium hexanoate, which has a much higher solubility than the longer chain fatty acids and therefore does not form precipitates, the gas dispersion properties of this surfactant were strongly enhanced in the acidic pH range, where hexanoic acid was fully associated. This result is an indication that undissociated hexanoic acid is much more surface-active than anionic hexanoate. Only a small effect of the surfactant chain length on gas dispersion properties of the tested reagents was observed. The measured critical coalescence concentration (CCC95) values increase slightly by decreasing chain length and range from 5.8 x 10-5 mol/L (17.7 mg/L) for sodium oleate to 7.2 x 10-5 mol/L (16 mg/L) for sodium laurate at pH 10 and 1.9 x 10-4 mol/L (26 mg/L) for sodium hexanoate at pH 3.7. These are compared to CCC95 of MIBC, which is measured to be 8 x 10-5 mol/L (8 mg/L). The soluble molecular species were recognized as the most effective species in preventing bubble coalescence."

Jan 1, 2014

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By M. Vasudevan

In sulfide mineral flotation, the efficiency of separation is severely affected by the presence of non-sulfide gangue minerals, such as altered silicates and serpentines. Although this is an acknowledged fact, most studies in mineral processing have focused on value minerals, and studies on gangue minerals affecting flotation performance are quite rare, and even those that do are limited in scope. This paper is an attempt to highlight the use of grade-recovery curves in studying the effects of gangue minerals. Specifically, we present the flotation response of problematic Ni and Cu ores which show highly uncharacteristic but similar grade-recovery characteristics despite the very different mineralogy and try to understand this behavior and the underlying mechanism. Finally, we propose chemical modifiers as solutions to overcome the detrimental effects of these gangue minerals and improve efficiency of flotation performance. Keywords: Non-sulfide gangue, grade-recovery, sulfide minerals, serpentines, talc, shale, slimes, spiking, modifiers

Sep 1, 2012

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

With the ambitious target of adding another 2,00,000 MW of power generation by the year 2017 in India the demand for coal is bound to grow. The non-coking coal deposits in India are characterized as high ash and difficult-to-wash coals. Quality improvement by beneficiation is almost mandatory due to MoEF notification to use <34% ash coal for all power plants except those located at pithead. Most of the coal washeries in India are based on wet process, where the coal fines are allowed to settle in thickeners. The coarser particles settle faster leaving the fine particles suspended for longer period. The dispersed fine coal particles contain some surface charge, which leads to the development of electrical repulsion between the particles, and as a result of this, the suspension becomes more stable. In order to destabilize the colloidal suspension, flocculants are usually added, so that the settling rate of the fine particles also increases. These flocculants are of cationic, anionic and non-anionic depending upon the type of charge released when dispersed in water. The flocculants may act partly for charge neutralization and partly for inter particle bridging and electrostatic patch formation. The effectiveness of any type of flocculants depends upon the molecular weight and charge density of the polymer. The paper discusses the settling behavior of non-coking coal fines suspension by using different flocculants. Keywords: floculent, coal fines, sedimentation rate, effluent

Sep 1, 2012

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTION Froth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity. The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By I. V. Shadrunova

Annually it is formed more than 95 Mt of clinkers in iron and steel industry of Russia, including 79 Mt of clinkers in blast-furnace, steelmaking, foundry and ferroalloy productions. Complex development of clinkers will provide not only extraction of valuable components, but also preservation of ecosystems. Processing of solid slags is realized, as a rule, in a cold condition by mechanical methods only including stage-by-stage crushing of slag on devices, working on principles of compression and shift (jaw and roll crushers). However it doesn?t provide the complete extraction of metals from clinkers. The intensification of decomposition, in our opinion, can be provided under the use of the devices working on a principle of free kick. At such influence on a material, its destruction occurs on micro cracks, sides of cohesion that is there is a selective destruction of the components possessing various resistances to impact. Decomposition of a piece on the basis of free kick about a material or metal is realized in centrifugal-shock crushers and mills of research-and-production association ?Ural Center?. The share of the joints sharply lowering the efficiency of enrichment thus is minimal. The efficiency of application is proved by morph-metrical measurements with the help of system of image analysis ?SIAMS-600? and physical-mechanical tests of clinkers and their components (impact strength, micro hardness). The experience of application the devices of centrifugal-shock crushing for processing clinkers in blast-furnace, martin and converter productions of Open Society MMC, clinkers of rough-edged copper melt of Joint-Stock Company "Karabashmed" and aluminium clinkers of Joint-Stock Company « Samara plant of aluminium alloys » has allowed to confirm the efficiency of application these devices for selective decomposition of metallurgical clinkers and the opportunity of using clinkers as resource of ferrous and nonferrous metallurgy.

Jan 1, 2014

By Chen Jianhua, Shen Zhenchang, Zhang Ming, Chen Feifei

"With flotation cells scale-up, the performance of flotation cells is increasingly variated for short-coming and dead zones existing. The residence time distribution which shows the movement of tracers can assess the unexpected flows such as short circuit and dead zone in a flotation cell. In this paper, the residence time distribution of pilot flotation cell is investigated with CFD simulation. Based on the theoretical model, the short-coming probability and dead zone probability are quantitative. The ideal average residence time is similar with the actual average residence time. The mixing effect of the flotation cell approaches the ideal continuous stirred tank reactor. The operating parameters such as speed and feed velocity have complicated influence on residence time distribution. The research would be helpful to understanding flow in flotation cell and improving performances of flotation cell.INTRODUCTIONFroth flotation is a method which purifies minerals according to difference of physical and chemical surface characters of different mineral particles (Shen, Z., Chen J, 2012). Flotation cell is a key equipment for froth flotation method. The flotation cell performances have great influences on flotation index.It is difficult to evaluate flotation cell how to improve flotation procedure to complexity.The main flotation cell performances are aeration volume, air dispersion, solid suspension and residence time distribution, etc (Shen, Z., Lu, S., 2008). Residence time distribution is an important fluid hydrodynamics which could reveal the flow of pulp, mixing of particles and air bubbles. In the flotation cell, the ideal average residence time of pulp could obtain easily. But the fluid differential units would be different flow paths. The residence time of the fluid differential units is variation and would be longer or less than the average residence time. The residence time distribution would reveal the mixing effect and predict the not ideal flow in the flotation cell such as shorting cutting, dead zone, etc. As we know, the shorting cutting and dead zone would be decreased the real flotation time and it is disadvantage to better flotation effect, especially for large flotation cell. It is impossible to eliminate the not ideal flow totally. It is very important to reveal and decrease the shorting cutting and dead zone probability in the flotation cell."

Jan 1, 2018

By Diogo R. Prado, José Aurélio M. da Luz

Drying operation can have a major importance in a mineral processing undertaking. The proper sizing of dryers can ensure the specified dewatering level without energy wastage. However, often the sizing of fluidized bed is done disregarding the actual residence time distribution (RTD) of the particles inside the reactor. In this case it is usual to adopt the average residence time as a design criterion. In this work, we have quantified the effect of residence time distribution on drying, ensuring that a previously adopted fraction of the particles remains inside the reactor for the required time lapse needed for drying. Design criteria such as particulate flow rate and drying time, taking into account the statistical distribution of residence time was studied, matching the thermodynamic and fluid dynamic aspects of the drying process. Experimental tests carried out have confirmed the RTD for a teetering bed as the same for a canonical ideal mixing system. Although the fluidized bed volume using the proposed formulation was higher than that found for the average time based procedure, the efficiency gain in drying has proven advantageous.

Jan 1, 2014

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By ?. Kostadinov

Theoretical study of the behavior of grinding medium presented by TBP (tetraballpebs) was conducted by computer modeling of the position of grinding medium at different speeds and different drum fill factor. For the modeling were used known equations of motion derived for the ball load. Algorithm was created by SolidWorks software, allowing determination of center of gravity of the load in the mill and energy for grinding. These results were compared with similar results obtained by ball grinding medium. The capabilities of both grinding media are demonstrated by graphics under the following conditions: 1.Equal dimensions of the experimental model of the mill; 2.Equal mass of the grinding loads; 3.Comparison of grinding bodies with the same number, mass and density. Keywords: simulation, behavior, grinding medium, balls, tetraballpebs

Sep 1, 2012

By R. D. Alorro

Melting has become a popular pre-treatment method for municipal solid waste (MSW) incineration residues in Japan. Although the method is effective in stabilizing the hazardous organic sub-stances such as dioxin, it concentrates the heavy metals such as Zn, Pb, Cu, and Cd in a newly formed fly ash (melting fly ash). Melting fly ash is classified as a hazardous waste because of the leaching potential of these heavy metals in landfill environment. Extraction and recovery of these metals seem to be more environmentally and economically attractive than disposing the material to landfill after immobilization process. This study proposes a Carrier-in-Pulp (CIP) method as a new hydrometallurgical route to reject and recover heavy metals from fly ash. In this method, a carrier material which recovers the extracted metals is added simultaneously with fly ash to leaching solutions and is harvested from the pulp by physical separation method like magnetic separation or sieving. To demonstrate the effect of CIP method, shaking flask experiments were conducted under various conditions using NaCl solution as lixiviant and iron powder or granular activated carbon as carrier materials. In the CIP method using iron powder, more than 97 wt% of Pb and Zn were extracted from the ash to the solution phase. However, the iron powder which was harvested from the pulp by magnetic separation, recovered only Pb (more than 94%) through cementation, leaving behind Zn ions in the solution phase. Due to this problem, granular activated carbon (GAC) was considered as an alternative carrier material. Single- and multi-metal adsorption experiments using granular activated carbon were conducted as a preliminary study. Around 85% Pb and 88% Zn were recovered by GAC in the single-metal adsorption experiment, while 60% Pb and 70% Zn in the multi-metal experiment. These results showed that activated carbon was superior to the iron powder since it was able to recover both Pb and Zn through adsorption. The leaching test conducted on the residue after the CIP-Fe treatment revealed that the solubilisation of Pb was successfully suppressed to meet landfilling guidelines.

Jan 1, 2014

By E. A. Brocchi

This work is dedicated to the chemical treatment of a typical EAF dust by chlorine content agents. The residue contains 48% Fe2O3 and 28% ZnO mainly in the franklinite structural form. The others less compounds are: 4.00% CaO, 2.60% MnO, 2.20% MgO, 1.08% PbO, 0.36% Cr2O3, 0.21% B2O3, 0.03% CdO and 0.01% NiO. The experiments purpose is selectively to remove zinc from the residue leaving the iron behind. Thermodynamics studies have indicated some roasting possibilities. The experimental results have shown that both HCl leaching and carbochlorination will remove iron and zinc without any selectivity. However, either the chlorine or the calcium chloride roasting seems to form, preferentially, the zinc chloride. So, it will be presented how the EAF Dust can be treated by the using of chlorine roastings process such as carbochlorination in order to separate the zinc and iron present in the frankilinite, main EAF dust content.

Jan 1, 2014

By A. J. Ren

The ore, dealt with in this paper, is a certain rutile in Shanxi province, China. A trunk flowsheet with gravity concentration is used, and the TiO2 grade of rutile concentrate is about 90%, but the TiO2 recovery is less than 50%. In order to increase the rutile recovery, the laboratory test, using the truck flowsheet with flotation, is carried out. The flowsheet is that firstly floatable gangue is re-moved by flotation; secondly rutile is recovered by flotation; and thirdly impurity is separated by LIMS, HIMS, gravity concentration and flotation from the rutile concentrate. In rutile flotation, BK423, a phosphonic acid, is used as rutile collector, and Na2SiF6 is used as silicates depressant. The experimental result shows that the recovery of rutile concentrate is improved obviously, and the recovery of ultimate rutile concentrate is 68.01% TiO2 and 84.88% rutile. The TiO2 grade of first concentrate is 95.98%, and the TiO2 recovery is 45.60%. The TiO2 grade of second concentrate is 80.53%, and the recovery is 22.41%. Furthermore, magnetite and ilmenite are recovered in the flowsheet.

Jan 1, 2014

By S. N. Shahcheraghi

Grinding is one of the most important and expensive steps in mineral processing allocating about 70% of the total energy in the plants. Nowadays, for optimizing the energy consumption in these equipments, the rock behavior and its size distribution during the crushing have been normally predicted using selection and breakage functions to be able to optimally model and design grinding circuits. For this purpose, the case of Miduk copper mine in Kerman province, Iran was studied. The samples were taken from primary ball mills feed and were subject to screen analysis to achieve uniform sizes. Then, selection and breakage functions were determined at the different grinding times in laboratorial ball mill. Finally, ore size distribution in different grinding times was estimated using MATLAB software

Sep 1, 2012

By V. Panayotov

Slag and by-products of metallurgy bear valuable components and their processing raises an in-creasing interest. Coke and iron have to be separated and other components have to be depressed, in order to obtain sellable high quality copper concentrates. Use of classical mineral processing technologies, such as magnetic separation, sulphidization, hydrometallurgy, etc. yields copper concentrates with grade of 4%~6% Cu. Copper is lost in tailings and the whole technological cycle is low profitable. Technology proposed applies an electrochemical treatment of the industrial water entering the flotation cycle. Iron and iron compounds that do not bear Cu, coke and gangue materials are depressed during the copper flotation. Copper concentrate of grade of 9.8%~10% Cu is obtained at simultaneous increase of Ag recovery by 8%~10%. As a result company profitableness is increased. Technology proposed is easy to implement, it does not require changes in the existing technology flow-sheet, and additional investment is low. The flotation process can be aided by a specially developed system for real-time analysis of the obtained copper concentrate which allows in-time corrections in the flotation parameters and entire process control. Applied flotation schemes, technological parameters and results obtained are described.

Jan 1, 2014

By V. A. Vorob'ev, A. N. Larionov, E. N. Ivanov, M. A. Ryazanov

The aim of the research is to increase the recoverable value of poor, difficult-to-digest complex mineral raw materials. In the Republic Belarus, universal centrifugal-shock devices have been created for crushing, grinding and classification of ore and non-metallic mineral raw materials in dry mode, which differ from foreign analogues by a higher level of resource saving (including electricity and materials). Dry-ore preparation technologies have been tested on a pilot scale: fine crushing (replacing grinding in rod mills), grinding (replacing wet grinding in ball mills) and pneumoclassification on different types of ores, - which made it possible to identify the criteria for the suitability and unsuitability of mineral raw materials for their use. The possibility of regulating the upper and lower limit of the size of the finished material is established, the possibility of reducing the yield of slimes (-0,020 mm) to 5 times is determined. A comparative analysis of the contrast degree of separation characteristics of ore a similar granulometric composition, crushed in wet and dry conditions, is performed. The achieved contrast degree of gravity properties after dry grinding - 104,3; after the wet - 60.2. When enriching on a centrifugal concentrator, gold recovery to the concentrate after dry grinding increased by 13.12% while improving the quality of the concentrate from 78.3 g/t gold to 90.75 g/t. When testing the gravity-flotation scheme for the enrichment of poor gold-quartz ore, the increment of gold extraction after dry grinding was 7.6% for gravity and 9.5% for flotation; the total increase in extraction is 17.1%. The possibility of flotation of a larger material after dry grinding has been proved, with an extraction gain of 1.5% compared to the flotation of thinner material after ball milling. The influence of dry technology on the efficiency of the leaching of gold and silver (an extraction gain of 5.5 to 10%) and heap leaching (extraction gain - up to 18.3%) was studied. The positive influence of dry ore preparation technologies on the efficiency of gold and silver heap leaching and heap leaching, thickening and filtration is proved. Lines of dry ore preparation technologies can be used in modular complexes for processing technogenic raw materials.

Jan 1, 2018

By S. V. Bogdanov, S. I. Grishaev

"The article presents the materials about the appropriateness of the use of rental indices to assess the effectiveness of the use of deposits of rare earth elements (REE). The authors suggest from the standpoint of rent payments to rate for the owner the possibility of using the anticipated rental income as the indicator for the analysis of preferences and economic significance of enrichment of extracted raw materials in the emerging field of rare earth metals (REE). Usually from ore mined at the fields, for flotation technology to produce concentrates with collective REE, then they are subjected to chemical-metallurgical processing of the received products are divided into pure oxides, chemical compounds or isolated from them pure metals and alloys. This commercial product is shipped to the buyer. REE were a non-renewable natural resources, so the calculations for determining differential and specific rent showed that during the development of the technologies of mineral processing of a specific field it is necessary to consider what the expected rental income depends on the magnitude of differential rent is related to the volume of production of REE for the whole planned period of exploitation of natural resources. This income is determined by the amount of stock field. For long-term exploitation of the deposit is observed in almost direct proportional dependence between the annual differential rent and the rental income. The decrease in rents in the long run is determined by the change in the composition of ores included in the extracted raw materials and the balance between light and heavy REE. The largest 70% reduction of the rent projected for ""cerium"" fields, while for ""yttrium"" these losses are considerably smaller. Tomtor, Chuktukon and Katuginskoye Russian deposits are characterized by a level of rent that is comparable to the mastered foreign sources of REE. Thus, the enrichment of minerals with REM in the domestic deposits is quite competitive at the world level. INTRODUCTION Deposits of rare earth metals (REE) are non-renewable resources that should be developed and used so that it would be possible to provide a reduction due to payment of appropriate resources for future generations. This compensation, due to the reduction of natural resources, can be carried out both in natural and in economic terms (1). When analyzing economic compensation options, particular attention should be paid to rental income in assessing the attractiveness of using different REE deposits. It is known that absolute and differential rents are summands when calculating the value of natural rents. The value of the absolute natural rent is proportional to the unit price of the product obtained from mineral raw materials and sold on the commodity market. Limitations, as well as the use in production processes and business, contribute to the gradual reduction of natural resources, which increases their consumer value and affects the price of commodity products from primary raw materials."

Jan 1, 2018

By C. Y. Wang

Based on Slurry Electrolysis, and combined with the problems of extraction antimony, lead and their separation from complicated antimony-lead concentrate, a series of tests have been done in this paper. Using Slurry Electrolysis to treat complicated antimony-lead concentrate, antimony and lead can be separated in one step. And 2# metal antimony can be achieved in cathode directly at the same time. Lead in concentrate is restrained still in the residue at the form of PbCl2. After converting the residue with ammonium carbonate and removing sulfur with kerosene, the high quality of lead concentrate (Pb is above 45%, S is below 15%) and pure sulfur can be achieved, respectively. The recovery of all in Slurry Electrolysis process is as: Sb 95%, Pb 95%, Ag 80%, S 60%.

Jan 1, 2014

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018