Search Documents

By Roger Keller, Jason Ryan

A number of studies have evaluated excavation methods for the construction of subsurface facilities for a potential deep geologic repository for the disposal of nuclear waste at Yucca Mountain, NV. Many of these studies suggest that where TBM (tunnel boring machine) methods are not applicable and alternative mechanical excavation methods can not efficiently excavate harder rock drill and blast methods may be the most efficient means of excavation. However, a number of concerns regarding drill and blast applications have been raised in these evaluations, most notably the affects of blasting on the surrounding perimeter, as isolation of the waste by the natural barrier of the surrounding rock is a key element in the concept of a deep geologic repository.

Jan 1, 2001

By Kenneth K. Eltschlager, Richard R. Brochu

At the International Society of Explosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this committee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same within stated tolerances.

Jan 1, 1999

By Francis Otuonye

Rock fragmentation by blasting still remains the most common and cost-effective method of excavating hard rock in mining and tunneling operations. During blasting, the dynamic stresses induced by the detonation of the explosive, in addition to fragmenting the rock in the vicinity of the blast, may fracture the rock at considerable distances from the point of detonation of the explosive. The fractures can result in reduced mine safety, increased costs to support the opening, low productivity and perhaps high ore dilution. Besides the dynamic stresses produced in the rock, air blast overpressure pulses are generated and propagate through the network of underground mine openings. The waves, unable to spread out spherically or hemispherically like blast waves from surface blasting, are forced to propagate by reflection from the roof, ribs and floor down the drift. Blast wave focusing can occur and produce intense shock waves that could damage ventilation barriers such as cement block stoppings.

Jan 1, 1992

By Kenneth Eltschlager

The Surface Mining Control and Reclamation Act of 1977 requires that blasting be conducted so as to prevent injury to people and damage to public or private property. The three adverse effects are flyrock, ground vibrations and airblast. Blasting close to people frequently results in complaints of annoyance or damage. Federal and State personnel are responsible for evaluating the validity of the complaint. The elements to be evaluated include: reviewing blast logs, inspecting the mine, inspecting the house, measuring ground, air and structure vibrations, and predicting vibration levels. Computer spreadsheets, with their graphical capabilities, will be used to show how data can be cross tabulated to verify data accuracy. Complete statistical analyses of vibrations require more powerful software to make vibration predictions. Once all available data are gathered and verified, a decision on the complaint can be made.

Jan 1, 2001

By Diego Quezada, Carlos Munoz, Marco Arellano

It is well-know that the presence of fine materials in mining has a direct impact on the plant processes with a great influence in the total amount of ore production and recovery. In Cu mining heap leaching is affected negatively by the presence of fines material (< 100 # Ty) in leaching piles, where a decreasing in Cu recovery is achieved in a lot of cases. D&B practices used normally in mine operations can generate fines > 4% in blasted piles, but the principal effects are reflected in the downstream processes where pre-conditioning post-blast materials release greater quantities of fines.

Jan 1, 2010

By A. Lindo, M. Held

The formation of NOx fumes is an undesired occurrence and is dependent on a variety of variables. Methods for detection of such fumes with blast analysis tools are available using color schemes for grading, but no quantification tools to measure concentration and cloud totals exist today. In cooperation with DIRS (Digital Imaging and Remote Sensing Laboratory) at RIT in Rochester, NY, Austin Powder has been looking for methods and techniques to identify and quantify total amounts of NOx by capturing cloud activity via a video feed from a drone in combination with measuring NOx and subsequent cloud modeling (i.e., plume segmentation). To accurately measure fume events, Austin Powder and the RIT team have been collaborating in performing small scale blasts at an Austin test facility and then transferring knowledge learned to full scale blasts at customer sites. The collected data will allow to identify any relationships between the total amount of explosives used and the quantity of NOx produced. The analysis of the total amounts of NOx and identification of blast areas those fumes originate from will help to better understand key factors that contribute to their occurrence as well as to quantify the severity of such events. By quantifying the magnitude and concentration of fumes generated by non-ideal detonations, the blasting technique can be optimized to minimize unwanted environmental effects and improve public perception of blasting as a necessary component of societal progress

Jan 1, 2024

By Mario Coderre, Andre Pinsonnault, Francois Lefebvre, Pierre Groleau, Yves Newman, Christian Pouliot

"This paper describes the blasting methods used to excavate the tailrace channel at theLaforge hydroelectric plant. It also shows the importance and versatility of the dopedemulsion explosives used in this project."

Jan 1, 1993

By Randall Head

The drilling at the Taum Sauk Reservoir was a unique compilation of the latest technology and everyday common sense. This site is comprised of rhyolite, which is 30 times harder than limestone in comparison. Using some of the most state of the art drills, coupled with GPS guidance, angular drilling systems, and an ordinary piece of string, some of the most amazing drilling feats were accomplished. By constructing the new dam on top of a mountain that had been blasted once before nearly 50 years ago treacherous conditions for the drills and crew were a challenge. The drills had to be flown in by cranes to get to their locations, where they then drilled anywhere from 2.5 to 6 inch (6.4 to 15.2 cm) holes at angles up to 24.4 degrees. Custom drill bits were designed by the drilling crew to tackle feats such as drilling holes up to 120 feet (36.6 m) deep. A main challenge was the shape of the reservoir, as it is not in a straight line, but rather round, so no technological way was readily available to use to drill. Common sense came in and an ordinary piece of string was used to aide in drilling the hole. A revolutionary step was that our drill was used to core our own samples. By using our own equipment, we were able to complete this task for one-third of the cost of having a third party contractor obtain the core samples. On this unmatched jobsite, it has been established that technology has come a long way, but when all else fails, a piece of string will do just fine.

Jan 1, 2010

By A. Ribeiro

The effective utilization of resources and process optimization play a crucial role in the sustaining and growth of overall businesses. This principle holds true in the mining sector, where particular attention is required during the comminution steps. This necessity arises from the fact that mining operations often consume substantial amounts of energy in mineral processing. Therefore, it becomes imperative to thoroughly study the integration of comminution steps. In many instances, an approach to be studied is the operation commencing with the drill and blast phase and culminating in the grinding product process. Nevertheless, establishing an optimal integration between drill and blast operations and the grinding phase is a complex undertaking due to the direct influence of rock characteristics on this process. And in many cases, the complexity and variability of such physical characteristics makes mining operations to ignore such influence. Consequently, Enaex Mining Technical Solutions (EMTS), in collaboration with Lundin Mining's Chapada Mine engineering team, and with the assistance of Hatch Consulting and Technology, has undertaken a comprehensive study aimed at enhancing mill throughput at the Chapada operation. The basis of this study lies in characterizing the rock masses present in the Chapada Mine to gain a deep understanding of the material that needs to be comminuted. Subsequently, the mineral processing team determined the most suitable size distribution for the Run-of-Mine (ROM) material. With this information, the drilling and blasting team built a site-specific blast fragmentation model, able to simulate various blast design scenarios. This approach enabled to optimize the utilization of available drilling and blasting resources while striving to achieve the optimum ROM characteristics. Since 2021, the Mine to Mill methodology has been progressively implemented at the Chapada Mine. As a result, the blasting engineering team now utilizes the blast plans generated by the fragmentation model simulations as a foundation for designing blast plans that align with the operational and financial capacities of the mine. Overall, it was predicted that this implementation could lead to an average increase in mill throughput of 13-22 % depending on blend feed, once all recommendations are implemented. Even with partial implementation, plant results demonstrate a 5 % increase compared to the period before the Mineto-Mill project, without any coarsening of the associated grinding product size.

Jan 1, 2024

By Dale Preece

In the late 1970’s and early 1980’s substantial resources were devoted to research focused on producing oil from the vast oil shale reserves in the western United States. Since the oil is solidified in the pore space of the shale, extracting it in production level quantities presented monumental technical challenges. Major advances were made in the methods used to extract oil from the shale in large quantities. Extraction methods evolved to culminate in the underground in-situ retorting process. In-situ retorting relied on explosive blasting of the shale to fragment the rock and induce sufficient porosity and permeability for a burn front to propagate through the oil shale. That burn front consumes some of the oil and liberates a substantial portion of it (~30%) for collection and further processing. Oil shale retorting is a blasting intensive process where the entire retort is rubblized in one very large, delay timed blast. Retort 7 in Western Colorado consumed 540,857 lb of slurry explosive to rubblized 348,940 tons of oil shale. Current rock blasting fragmentation predictive capabilities have evolved substantially since these retorts were designed and tested. It is the purpose of this study to simulate the explosively induced fragmentation of oil shale using state-of-the-art computer codes and material models and to infer retort design implications for future development.

Jan 1, 2007

There is an intuitive tendency to equate rock strength with rock stability, yet the two must be evaluated separately. A slope in strong hard rock is not necessarily stable, nor is a slope in weathered weak rock necessarily unstable. In some cases the reverse is true, depending on the geometry of joints and weak planes. The time element is a matter of special concern, that is how suddenly the failure begins and how rapidly it progresses. Sudden failures can be catastrophic, whereas creep usually is not. In soils and weathered rock, the process is usually incremental and is more likely to give some warning of impending failure. With careful observation, the failure process in these materials can be detected and monitored instrumentally or visually. In some cases, the slope may be stabilized, reinforced or modified. When that is not possible, there is usually enough time on this type of slope to remove men and equipment from the area before complete failure occurs.

Jan 1, 1996

By Ulrich Leiste, David M. Fox

This paper presents the results from small scale testing aimed at measuring the loads on a rigid target due to the detonation of a buried mine. The aim of this research is to find how the impulse delivered to the target varies as the air filled void volume fraction within the soil changes.

Jan 1, 2013

By Raúl Mondaca Aracena

Mantoverde mine requires increasing its production level to double. EMTS - Projects performs far and near field vibration studies to make changes to the D&B design and sequences, in order to equalize the current vibration levels, applying massive blasting in its process.

Feb 1, 2020

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

By Sami Kara, Marsel Nabium

As a mining project is developed from conceptual to production phases, there exists a variety of uncertainties and difficulties that affect the operation’s designs and economic values. A notable design parameter to be taken into account is the factor of dilution. Dilution is the waste material not separated from the ore in the stages of mining and is sent to the processing plant. It is defined at the ratio of tonnage waste mined and sent for processing over the combined ore and waste tonnage milled. Dilution reduction is one of the areas that offer metal mines an opportunity to increase revenue and reduce costs, resulting in enhanced profits. Effective dilution control programs require interaction on a multidisciplinary level. This paper outlines recent initiatives undertaken at Polysmetal Silver Magadam Mine to reduce dilution and increase revenue. This paper provides an overview of the solution applied in underground Silver mine in Russia. The paper reviews the dilution problem throughout the entire mining process, and provides a rational approach to underground mine Blast design in order to minimize dilution. The mining companies put a lot of effort into extracting lower grade while minimizing cost. The dilution control assists with achieving this goal. In Polymetal Silver Magadam Mine we succeeded to control more than 20 blasts by keeping almost the same grade measured in the face. The results indicated that using the adequate blasting timing design can help to separate the ore from the adjacent waste in drift blasting with different ore body configuration.

By William R. Adamson, Carlos R. Scherpenisse

The successful development of surface mining operations depends, amongst other factors, on the successful creation of final pit walls which offer long term structural stability. The achievement of such walls will be much more feasible if the mechanisms of rock mass deterioration in the mine are well understood, permitting the control and reduction of this deterioration (or damage). The role of drilling and blasting in causing damage is widely accepted but rarely fully quantified. It is also true that the dependence of rock mass damage on vibration levels is only incompletely understood and little accurate field measurement is routinely conducted in the mining industry.

Jan 1, 1998

By M Sampara, W Comeau

The introduction of large-diameter holes to underground mining has made possible the development of new mining methods such as the Vertical Crater Retreat (V.C.R.) method. It is not only the safest underground excavation system but also provides mass production at a lower cost than any conventional mining method (1, 2, 3, 4, 5).

Jan 1, 1981

By Conny Postupack, Jim Petrunyak, John Loope

The authors discuss the concepts, engineering considerations, and cost relationships involved in the use of drilling and blasting to accomplish backfilling and reclamation with minimum use of mechanical equipment. The four methods of reclamation now in use are reviewed, and their advantages and disadvantages are noted. Guidelines for selecting a particular method are offered in terms of applicability under varying geologic, economic, and technological conditions.

Jan 1, 1987

By Jeffrey A. Straw, Joseph P. Jr Shinko

Ground vibration produced by blasting operations within South Florida, due to saturated soil conditions, generates surface vibration waves that may be measurable over distances of 3 - 5 miles from the source, and perceptible at distances of up to 2 miles. Structures above ground usually receive the most of the attention from the effects of high vibration levels. During construction of the Trilogy Development of the Swerdlow Companies, blasting was completed in a lake excavation immediately adjacent to the City of Pembroke Pines Utility Department, Deep Injection Wells No. 1 and No. 2.

Jan 1, 1994

By C. Aimone-Martin, C. Dowding, M. Jern, J. Gjødvad

This article compares percentages of compliance for six national standards to demonstrate how these standards vary on-site in a real project. This, to the best of the authors' knowledge, has not been accomplished before. Different standards not only vary in allowable amplitudes of induced vibrations but also in how they are measured (transducer location, transducer orientation, frequency content of vibration, etc.). Thus it is not straightforward to compare the permissible values of induced vibrations with each other. This challenge of comparison is overcome in this project by instrumenting a structure with multiple transducers according to different national standards and comparing the degrees of compliance. Compared herein are compliance with standards used in United States of America, Germany, Great Britain, France, Austria, and Sweden. Averages of the percentage of compliance and ratios of measured vibration amplitudes for all six national standards are compared both in tabular and graphical form for 20 blasts at the Aitik mine northern Sweden. It is the largest open pit mine in Europe and blasts are atypically large with more than 1000 kg charge per hole and several hundred holes per blast, lasting 3-5 seconds. Results show that percentages of compliance can vary by as much as 2 to 75 % for these blasts at this structure. The overall project is a cooperative effort between EFEE (European Federation of Explosives Engineers) and ISEE (International Society of Explosives Engineers), supported by more than 17 persons from 8 different countries. At the present the experts are the four authors of the present paper and Dr. Robert Farenfield, Dr. Nathan Rouse, Douglas Rudenko, Brent Meins, Kenneth K. Eltschlager, Karin NorénCosgriff, Travis A. Davidsavor, Vitor Luconi Rosenhaim, Johannes Kutschera, Bernard Thierry, Thomas Moser, Cory Loukedis, and Keith Best. The project began with a literature study and a survey including an evaluation of the answers provided by members of EFEE. Results were presented at the ISEE conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019 (Gjødvad & Jern, 2019; 2020). The second part of the project was initiated in May 2021 with installation of 7 seismographs from two different manufactures, 3 cracs gauges and 2 microphones on a building at the Aitik mine in northern Sweden. The third part of the project has moved to the United States. Two residential structures adjacent to quarries are being monitored in Michigan and Ohio. Installation and monitoring began in March 2023 and are expected to continue for 6 to 12 months. In addition to the objectives of phase two the 2023 study includes calculations of global wall strains from measured velocity time histories and measurement of response of existing cracks to vibratory and climatological effects

Jan 1, 2024