Search Documents

By L. M. Lopez, J. A. Sanchidrian

This work investigates the performance of some of the measurement techniques used in vibrations from blasting monitoring. Two tri-axial geophones with cases of different size, shape and mass were tested in a shaker table. The geophone cases were mounted in three different ways on a granite slab fixed to the plate of the shaker: freely placed, sandbagged, and anchored. A known horizontal periodic motion of constant amplitude, and frequency from 16 to 200 Hz, was applied to the slab. Two amplitude levels of 5 and 20 mm/s (0.2 and 0.79 in/s) were applied when the sensors were sandbagged or anchored and only 5 mm/s when no holding force was applied. The transmissibility of vibrations from the rock to the longitudinal geophone as function of the frequency (i.e. ratio of response of the geophone to the slab motion) has been obtained for each measuring condition tested. The transmissibility is considered a composition of the transmissibility of the rock-to-sensor coupling and the transmissibility of the sensor’s mechanics and electronics. The transmissibility of the coupling is obtained normalizing the total transmissibility with the transmissibility of the seismographs, obtained by a suitable test to which a coupling transmissibility of 1 is assigned. Geophone-to-rock coupling is a resonant phenomenon that may alter the amplitude of the measured waveforms by a factor of 1.2 to less than 0.6. The most accurate and precise measurements are obtained with geophones anchored to rock. On the contrary, freely placed or sandbagged sensors are non-predictable planting conditions that lead to high amplification or damping in most of the frequency band analyzed. It is also shown that existing acceleration criteria to select coupling methods do not necessary lead to good quality (accurate and precise) vibration data.

Jan 1, 2014

By Claude Cunningham, Szendrei

The partitioning of blasting energy into “Shock” and “Heave” components is a popular concept for attempting to match explosives to particular ground conditions and blasting results. The issue is complex, as it affects both the detonation process and the immediate response of the rock skin. However, the fundamental process of energy transfer from the explosive to the rock through the blasthole wall is not well defined. Clues to the “Shock” phase of blasthole expansion are given by cratering behaviour of materials subject to high velocity penetrators. The final cavity volume defines both the energy used to achieve this and the resistance of the confining material. Attention is being given to the link between penetration of a solid target and expansion of a readymade hole, both producing the same outcome. The benefit of this work is that it leads to clearer understanding of how explosives will impact upon the blasting results and helps to explain the energy consumption in blasting.

Jan 1, 2004

By Kinross Paracatu, Victor Morais, Luis Marinho, Rolando Fuentes, Lucas Steffen, Leopoldo Muñoz, Washington Vilas

Nowadays, mining operations close to communities face increasingly challenges, especially in their drilling and blasting operations. One of the critical effects are the ground vibrations produced in its surroundings. The impact on the community must be minimized to guarantee the license to operate and, on the other hand, costs must be optimized, and an adequate fragmentation must be achieved to ensure the efficiency of subsequent processes and, consequently, to give sustainability to the business. In this regard, it is necessary that some controlled blasting technique to be performed and the utilization of advanced vibrations models. Currently, it is common in the industry either use of the double decking technique, where very low explosive charges are applied, making it necessary to use smaller drill patterns in order to keep powder factor as per design, which strongly increases the demand for drilling and a consequent impact negative on costs.

Feb 6, 2023

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine in 2005 to 2007 to determine the extent that using electronic detonators could increase Semi-Autogenous Grinding (SAG) mill throughput. The results of that project were reported at the 2010 ISEE Annual Conference. This paper is a postscript to that project and provides the fragmentation resulting from the implementation of a 15% pattern expansion using electronic detonators.

Jan 1, 2012

By Jerry Newton

The bulk explosives industry is relatively young compared to how long explosives have been in use. It's been around for about forty years, about the length of a person's career. This period of explosives history has seen constant change. The type of product, the manufacture and the trucks that haul it have changed a great deal over the years.

Jan 1, 1997

By K Uenishi, H P. Rossmanith, N Kouzniak, A Daehnke

This contribution presents an introduction into that part of the field of elastic wave propagation which is relevant to blasting of boreholes and addresses briefly borehole breakdown and the formation of the fracture network around a borehole which ultimately leads to the disintegration of the rock mass. Phenomena of this kind are encountered in mining and quarrying. Numerical as well as experimental work referring to stress wave expansion from a detonating borehole is addressed.

Jan 1, 1998

By Henry P. Van Ormer

This paper is written to outline the capabilities and flexibility of the electric motor driven oil cooled rotary screw air compressor in construction and mining applications. With the changing economics between fuel and electric power all over the world, the viability of the electric motor is a choice all construction and mining people should be aware of. The advent of large efficient electric motor driven rotary screw compressors have given a great deal of flexibility to the use of these units on many applications not considered before. Examples are given for rotary and percussion drilling, fennels, and underground, sandblasting and "uniting, general uses - shows wheel mounted and skid mounted units.

Jan 1, 1976

By Pierre Mousset-Jones, Geraint W. Harris, Robert Karlin, Jaak Daemen

In order to minimize the ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will make it possible to more accurately locate the grade boundaries on the surface of a blasted rockpile prior to excavation. This paper describes the development and testing of a method to accurately measure the direction and magnitude of sub-surface blast movement. The technique involves the use of magnetic "radiometry, using a cesium vapor "radiometer and real-time differentially corrected, GPS system, to locate the post-blast position of magnetically enhanced target objects, whose pre-blast locations are known, without disturbance of the blasted rock. The objective is to design an accurate and efficient technique which can be integrated into a mines production cycle.

Jan 1, 1997

By Paul Worsey, Braden Lusk, Seokbin Lim

This paper discusses the theory and experiment involved in the discovery of the mechanisms of Linear Shaped Charges, which are much different from those for Conical Shaped Charges. Linear Shaped Charges (LSC) have been assumed to function in the same manner as Conical Shaped Charges (CSC) in the published literature on the subject. Much work has been done on CSC for military purposes, but there is limited information about the mechanics of LSC. Previous theories have cited the formation of a Monroe Jet as the dominant process. The Monroe Effect describes what happens to a target below the charge following detonation of the charge, and prescribes a fluid jet process for penetration. The fluid jet comprised of the liner material is the cutting device in CSC and has been extensively studied. Recent work at the University of Missouri at Rolla (UMR) cutting concrete with LSC has surprisingly shown that there is not a fluid jet process in LSC. After completing several reinforced concrete penetration tests, minimally deformed copper blades were found in the debris. Initially, the blades were suspected to be misfires or malfunctioned charge remnants. However, results were good and blades were found after every single test. Upon closer inspection, the ribbons were found to be folded copper and they were suspected to be the bottom liner of the LSC. A test series was conducted to verify the new theory by experiment.

Jan 1, 2005

By Sandra Penttinen

There are several ways to get a positive reaction from abutters to blasting projects. When you need to enter structures to conduct a blast-blast inspection, the impression you make on the structure owner must be positive from the very start. Your public relations with neighbors is the key. The purpose of all communications with persons residing near planned blasting operations is to educate structure owners as to what will take place during the blasting operations, to explain that safe blasting practices will be followed and vibration and airblast limits will be imposed to protect surrounding structures from damage. Once access into structure is obtained, the structure owner can be shown, by careful documentation, all existing cracks and defects in the structure prior to blasting and construction. The objective of your visit and all communications is get your foot into the door and win the confidence of the structure owner so that he or she understands blasting will not compromise the structure.

Jan 1, 2005

"Blasting is an inherently destructive process and inflicts damage to the immediateperiphery of an excavation, which is later manifested as ground control and dilutionproblems. Different explosives release their energy and interact with the rock in differentways."

Jan 1, 1993

By Gregg R. Gitschlag

There are more than 4,000 oil and gas structures present in the U. S. Gulf of Mexico. Approximately 100 structure removals occur each year and 66% of these are removed with explosives. From 1993-1995 an intensive study was conducted on the fish kill resulting from the explosive removal of 6 platforms off the Louisiana coast in water depths from 14-28 m (45-92 ft). After explosives were detonated, all floating fish and a sample of the dead fish which sank to the sea floor were collected.

Jan 1, 1997

By Rolf R. Schillinger

Subject of the paper are blasting vibrations as sources of environmental molestations including acceptance level,complaint level and damage level as well. Besides, the subject shows a comparison of international regulations and their problematical aspects. In consideration of blast induced immissions the subject shows that human annoyance has become an important place in blasting works. It provides a solution proposal how to minimize environmental effects of blasting works.

Jan 1, 1996

By Y Nagendra, A. Ravi Kumar

A breakwater is a construction for protecting the marine structures like port, harbor, or anchorage-basin and berthed marine vessels from the destructive influence of the sea waves. The breakwater is constructed by using geologically competent, heavy, massive rock like granite, basalt etc having physical and mechanical properties within the limits specified by the designers. The construction requires boulders in varying sizes ranging from 0.5 kg to 20,000 kg. The stones from 0.5 to 1000 kg are called as core fill and boulders greater than 1000 kg are termed as armor blocks. These armor blocks cover and protect the core fill and prevent it from escaping. The requirement of armor blocks ranges between 25 to 35 %. The rest is core fill. However, the actual requirement depends on the breakwater design. In this context, the task of the mining engineer is to economically produce armor blocks and core from the designated quarry in right proportion with minimal losses. The whole bunch of engineering ingenuities should be put forth for obtaining the required armor blocks. The armor block production from any blast depends chiefly on geological conditions, bench dimensions and blast design. This paper is an attempt to bring out the various parameters affecting the performance of the blasting for armor block production using a case study.

Jan 1, 2005

By John C. Adams, Robin Irwin

In early 1993 a test program was designed to determine if mining costs could be reduced by using a high density ammonium nitrate mini-prill blasting agent. The goal was to reduce mining costs by expanding blast hole patterns while maintaining or improving dig-ability of the shot material. The program was conducted at Santa Fe Pacific Gold's Lone Tree gold mine near Valmy, Nevada.

Jan 1, 1994

By S. Hosein, W. Birch, C. Johnson

The widespread adoption of electronic detonators has given rise to the development of linear superposition to control the environmental impact on both third-party properties and residents resulting from blast induced vibrations. Linear superposition has become a very effective tool in the hands of blasting engineers and has enabled aggregate reserves to be accessed that once had to be abandoned. This in turn has resulted in more and more complex blasting pattern to be developed that contain multiple rows and multiple decks all with different maximum instantaneous charge weights of explosives. This is then made more complex by having to consider multiple sensitive locations often with different Peak Particle Velocity vibration limits. This paper is a case study of what did happen when a blast was designed that “pushed the boundaries” of environmental blast vibration design and control, without taking fully into account the fundamental geophysical properties of seismic waves. The resulting blast design caused a greatly enhanced s-wave to be created in a critical direction from the blast pattern. The root cause being the s-waves from earlier detonating decks in the blast pattern arriving within 2 milliseconds of decks detonating later in the blast pattern. 209 individual decks were fired in the blast pattern of which 41 pairs of decks arrived at the observation location less than 2 milliseconds apart when taking into account the s-wave speed and direction. The lesson to be learned when using electronic detonators to limit ground vibrations from complex blasting patterns, is that it is just not good enough to look at the planned firing times, a professional blasting engineer must also understand the likely interaction of the various seismic wave types created and their combined impact on any given monitoring location.

Jan 1, 2024

By Douglas R. Burns

In New England, an area of the country where 3 ½" holes are considered large diameter,we are starting to experiment with 5" and 6" holes. The results are excellent in some areas and poor in others. The geology of rock is the major consideration to account for the blasting results.

Jan 1, 1997

The following situation was submitted as an ethics case study for inclusion in the Journal. To the best of our knowledge, they are based on actual circumstances encountered in the field. Blowing the Whistle Protecting Confidentiality or Doing the Right Thing? This case centers around a construction job and involves a contractor, subcontractor/blaster, and a farmer/homeowner who lives near the job site. It is essentially a study of professional ethics versus morality, our professional code of conduct versus what is right or wrong.

Jan 1, 2007

By W. J. Birch

The recording of information is critical to the blasting process, whether it be for planning purposes, statutory requirements or environmental compliance. The review and analysis of past data can play a key part in a blast.s design. Statutory records must be held to preserve operational licenses and well-maintained monitoring records are a vital defence for today.s litigious society. However a single blasting event can be responsible for generating vast amounts of data. This information maybe collected pre or post-blast and in their individual ways may have a requirement to be logged, processed, analysed, reviewed and reported before eventually being archived.

Jan 1, 2002

By Daniel Johansson, Markus Danielsson, Håkan Schunnesson

In sublevel caving, blasted material flows gravitationally into the drawpoint from above in a periodical manner. This type of flow behavior entails muck pile conditions that are variable along the course of extraction. The effect of this variability on the LHD (Load-Haul-Dump) operation in terms of loading efficiency and ability to undermine the blasted ring is not fully understood as of today. This paper presents results from a field test in LKABs Malmberget mine in Sweden, where the influence of fragmentation on the loading operation has been studied in detail. Drawpoint filming was conducted for extraction of two rings equivalent of roughly 10000 metric tons (~9842 long tons) of material each. The analysis includes fragmentation measurements, muck pile classification, and general estimations in terms of loadability. Further, an evaluation of LHD machines from two different manufacturers was conducted to identify and highlight differences. The results show that fragmentation, muck pile compactness, and flow characteristics are all interdependent. Flow disturbances and the subsequent loading of compacted fine material in the back of the ring have been identified as the main reason for occurring problems and prolonged digging times. However, the ability to sufficiently undermine the blasted ring has been identified to primarily depend on digging depth which is only observed to be high during flow disturbances. An absence of flow disturbances seem to promote high loading efficiency but simultaneously limit the maximum digging depth. A mid-range particle size distribution with a low amount of fines has proven beneficial for overall loading efficiency. The various LHDs employed showed significant variations in terms of ability to handle difficult loading situations (e.g. compactness, boulders, etc.).

Jan 1, 2018