Search Documents

By D Anonby

The Fox Pit at EKATI Diamond Mine is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high faces. Blasting tests were conducted to increase the percentage of benches that meet an 11 m catch width. The subdrill depth for the lower bench trim blasts and the blasthole diameter for the upper bench trim blasts were reduced to maintain the bench crests. Raising the lower trim blastholes by 0.5 m decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. The use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest.

Jan 1, 2007

By Larry Mirabelli, Gerard J. O'Brien

"The construction of the Third Harbor Tunnel is a key element of the Central Artery TunnelProject. The tunnel is to traverse Boston Harbor directly linking South Boston to EastBoston. The tunnel is a cut and cover tunnel as opposed to a bored tunnel. The cutdimensions are 95' wide, 110' deep and approximately 4000' in overall length."

Jan 1, 1993

By S K. Mandal, S Dasgupta

"Damage is classifi ed as loss in the integrity or deterioration in the quality of rock massand is infl uenced by methodology of excavation on the geo-technical properties of rockmass. Overbreak, on the other hand, is the result of damage and is quantifi ed in either of the terms viz., extra mucking, shot-creting, application of extra support system and extension of scheduled completion time. Damage or overbreak in rock mass by the impact of blasting, is generally unavoidable but, the magnitude can be minimized so that it does not deteriorate the quality or integrity of structure. The paper, here, analyses magnitude of overbreak of a powerhouse cavern with respect to different blast patterns implemented at the site. The magnitude of overbreak was analyzed in terms of profi le measurement with the help of laser profi ler and percentage of halfcast markings observed on the periphery rock wall. The paper revealed the impact of decoupling ratio, blast pattern and geometry of blasting patch on the magnitude of overbreak. The authors observed that presence of un-favourable joint pattern or foliation plane along the periphery rock wall couldn’t contain magnitude of overbreak within allowable limit. The analyses revealed that percentage of half-cast markings on periphery rock wall was infl uenced by response of rock towards detonation of explosive and cannot be a single parameter to assess the effectiveness of a blast. The analyses also revealed that magnitude of overbreak for down-stream wall was more than that observed in up-stream wall."

Jan 1, 2008

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By N. Paley

An engineering project was undertaken at the Cominco Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by blasting differently. The Julius Kruttschnitt Mineral Research Center (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast design to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed and the powder factor increased to maximize fines. However, JKMRC research had shown that it appeared possible to increase primary breakage by blasting to such an extent that SAG mill throughput could reach a plateau or even begin to decrease. Modeling was carried out on a range of blast pattern geometries and emulsion explosive blends to determine if a plateau existed and at what powder factor it would be reached. It was found that the relationship between powder factor and grinding throughput was nonlinear. Modeling was also used to compare the SAG mill throughput which could be expected from different emulsion explosive blends to determine which blends should be used in dry and wet holes to provide similar fragmentation. For heavy-ANFO mixtures, the highest modeled throughput was at a ratio of 30/70, with ratios on either side indicating lower throughput. For emulsion blends, the highest modeled throughput was at a ratio of 80/20; however, ratios from 80/20 to lOO/O were similar. Crusher product size distributions were obtained from belt cuts early in the analysis to confirm model predictions. At later stages, actual SAG mill throughput was compared to predicted. The economic benetit from the different blast designs was calculated by accounting for the reduction in recovery due to the higher throughput and the additional drilling and blasting costs. Increasing the powder factor by 150% from the 0.29kg/t {0.58lb/st] being used to 0.72kg/t { 1.44lb/st}, the maximum feasible with mine equipment, could provide a sign&ant net benefit of $3OWyr due to the increased concentrate production. However, because the relationship between throughput and recovery is affected by other factors which were not modeled, a more conservative approach was taken. The powder factor was instead increased by 50°h, providing 45% of the gain. This was possible because the relationship between powder factor and grinding throughput was nonlinear.

Jan 1, 2001

By Cathy Aimone-Martin

The City of Henderson, Nevada is experiencing extraordinary population growth. Some residential development requires blasting to be conducted at close proximities to high-value houses. Blastingrelated concerns voiced by the community residents include dust, noise, fears of damage to residences, and claims of insufficient controls exercised by the blasters. Residents perceive geological conditions are adverse to the protection of structures at the current vibration regulatory limit of 0.5 in/s. Airblast limits are 120 dB. Vibrations felt within structures leave home owners with the perception that damage is taking place. New cracks appearing in homes at distances far from the blasting are being blamed on blasting.

Jan 1, 2007

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

The basic metric for linear shaped charge performance is the amount of cutting distance that the charge can effectively yield given a specific standoff and target. Due to its size and restricted production runs the 10,500 grain/foot (2,232.25 grams/meter) linear shaped charge has had only limited studies that examine cutting performance and standoff. This article covers research regarding cutting performance verses standoff as the charge is applied to common structural steel. Specifically this study uses A36 mild carbon structural steel blocks of 10.16 cm by 11.80 cm by 35.56 cm and standoff distances of 0.5, 1.0, 1.5, and 2.0 charge diameters. Data presented includes the presentation of actual cutting performance numbers, comparison of that data to projected performance based on currently recognized industry guidelines, and a discussion of what may contribute to the performance found in this study.

Jan 1, 2013

This paper presents a brief discussion of three case histories to illustrate several aspects of the question of blasting in or immediately adjacent to concrete. The results demonstrate a need to make dramatic upward revisions in previous criteria, whether it be the standard particle velocity criteria or damage response spectra bounds, - especially those which include conservative upper limits of constant acceleration for the high-frequency portion of the spectrum. It is demonstrated, also, that conventional off-the-shelf blast-monitoring instruments are not capable of monitoring small blasts at close range. Both the frequencies and the levels of effect are beyond the range of such instruments. These case histories suggest further that there is a need to review the applicability of certain wellknown equations of elasticity.

Jan 1, 1980

By D K. Joyce, B Mohanty

In a previous paper, it was shown that a lack of clear understanding of the role of initiation mode on detonation characteristics often leads to under-utilization of the explosive system in blasting. This is of particular significance since the very large number of explosive initiation practices currently in use implicitly assumes that the blasting performance of an explosive is largely independent of the exact mode of initiation. This paper deals specifically with bulk-loaded and pneumatically-loaded ANFO under various initiation modes in small diameters. These include initiation by booster and detonating cords of various strengths, and combination of cords and boosters. The nature of energy release and energy partitioning between shock and gas energy have been studied in the underwater test as a function of charge diameter. The paper describes the relative merits of various initiation modes for specific charge geometries and confinement, under end- and side-initiated conditions. Guidelines have also been formulated for use in the field to match initiation practice with blasting requirements.

Jan 1, 1994

By Donald D. Eilers, Pharis E. Williams, Thomas O. McKnown

The Continuous Reflectometry for Radius vs. Time Experiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation.

Jan 1, 1995

By Alex Jankovich, Darren Thornton, Sarrna Kanchibotla, Cam Grundstrom

The Porgera joint venture and Dyno Noble have commissioned a joint project to optimise the drill and blast operations to increase the overall profitability of the mine. One of the aims of this project is to increase the throughput of semi autogenous (sag) mill by optimising the blast fragmentation, The work done so far clearly indicates that significant improvements in sag mill throughput can be achieved by optimizing the blast fragmentation. This paper discusses the planning, implementation and results achieved so far in this project.

Jan 1, 2001

By Salah A. Taqieddin

The blast casting technique of removing overburden is an innovative technique which was successfully used in the mining of certain surface coal and quarries. This method was found to be efficient in minimizing the labor and equipment cost while accelerating mining operation with safety. This method was successfully applied to horizontal as well as to dipping coal seams. Also it was practically applied to single as well as to multiple ore bodies

Jan 1, 1992

By Robert B. Hopler

This paper reviews, from the historical standpoint, the development of the commonly-used terms such as "No. 6 and No. 8" with regard to detonator strengths. The origin of the strength terminology is reviewed, and the many methods developed to compare the strength of one detonator to another are described, with the good and bad points of each method outlined. The "miniature cartridge test," very highly regarded by both the U.S. Bureau of Mines and Institute of Makers of Explosives in the 1930's and early 1940's, is described in detail, as is a test developed and used by IRECO.

Jan 1, 1992

By Jacques Monette, P K. O'Connell, Keith Boyle

The mine contracting industry in Canada is no different from any other industry in its quest for productivity improvements. Dynatec Mining Ltd. has focused on drilling and blasting of rounds as an area for improvement. This paper describes the development of blasting long rounds in shaft sinking as well as a description of the lateral excavation system as applied at Aur Resources Inc., Louvicourt Project.

Jan 1, 1994

By Michael Weaver, Dale Ramsey

Description of Project: The National Gateway Clearance Initiative is an improvement program to achieve a minimum of 21 feet of vertical clearance along CSX Transportation Inc’s (CSX) rail corridor so that double-stacked intermodal railcars can be transported between mid-Atlantic states and their ports to midwest markets.

Jan 1, 2014

By Unknown

[Executive Director’s note: According to 17th edition of the ISEE Blasters Handbook in its section on trench blasting, “...consideration must be given to the proper venting of gases generated from the blasting. Should those gases spread laterally rather than vent directly to the surface, the gases may travel underground and finally vent well outside of the planned area. Such events may be caused by the strata, soil conditions or root systems, or existing and/or abandoned utilities or other man-made structures. In the worst situation, gases resulting from the detonation such as CO2, CO, and/or NOx may travel through the strata and find their way into basements of nearby homes or businesses. The IME has recommendations on how to minimize this potential problem. Some of the points include removing the overburden and digging the rock immediately after the shot, and drilling vent holes periodically between the ditch and adjacent homes.” The Board of Directors of the International Society of Explosives Engineers has expressed its concern that blasters be made aware of the issue of migration of carbon monoxide resulting from blasting operations. What follows are excerpts from “Carbon Monoxide - The Silent Hazard”, an article that was recently included in the Safety Update, Vol. 20, No. 1, 2001, published by Nobel Insurance Services.]

Jan 1, 2002

By Robert A. Cummings, Francis S. Kendorski, Charles H. Dowding

During the summer of 1980, a field project was carried out to determine the stability of the beautiful and dramatic natural limestone pinnacles (locally termed "Hoodoos") at Bryce Canyon National Park, Utah, when subjected to ground motions and airblasts resulting from proposed strip coal mine blasting. The concern arose from environmental considerations associated with the proposed development of a large coal strip mine which would approach within 4 miles of the park. The pinnacles range up to 150 ft in height and are quite slender, producing a fragile appearance. The remoteness and ruggedness of the area required a field camp, and 4-wheel drive vehicles, helicopters, and snowcats for support. Portable magazines were necessary to store the more than 7 tons of blasting agents and explosives required. In conducting the blasting, great attention was paid to environmental impacts. In the field, a target pinnacle was selected and instrumented with mechanical strain gages, and research seismographs that required helicopter placement.

Jan 1, 1982

By Chuck Kliche, Bill Clements

This project involved the removal of the top of an old water supply reservoir tank for the City of Lead, SD by explosives. The general contract called for the removal of the concrete top without damaging the sides or floor of the reservoir. The option of a rock hammer was eliminated, due to the possibility of an unpredictable collapse damaging the sides or floor of the reservoir. Different blasting options were discussed between the primary contractor and the blasting contractor, along with the pros and cons of each. The primary contractor settled on the option of drilling the structure for blasting versus using shaped charges

Jan 1, 2007

An explosive's velocity of detonation (VOD), can be used to indicate a number of important characteristics regarding the product's performance under specific field and test conditions. A number of new characteristic and transient VOD curves have been identified in the field, which can be used to evaluate explosive performance, control ground vibration amplitudes and frequencies, select the correct amount and type of stemming for use at the collar and in stem decks, eliminate explosive desensitization, evaluate primer performance, design air deck based blasts, evaluate contaminated explosives and to overcome post blast noxious fumes.

Jan 1, 1994

By Ray Jambakhsh, John Okell, Frank Cook

"In early 1988, an experimental study was carried out at the Inco's McCreedy West Mine inLevack, Ontario. The objective was to develop blasting techniques which would allow themine to maintain production targets and reduce blast induced vibrations and overpressure.Due to its close proximity to the town of Levack (approximately 900 feet), particularconcern was expressed as to the vibration and overpressure resulting from the undergroundblasting operations."

Jan 1, 1993