Search Documents

By W. Reisz

Blast area security is the responsibility of everyone involved in the blasting operation and goes well beyond simply controlling access by unauthorized personnel.

Jan 1, 2009

By V. Sastry

Signgareni Collieries Company Ltd. is operating the JK Opencast Project, at Yellandu, with a rated annual capacity of 1.6 Mt of coal with an average stripping ratio of 4.3. This opencast coal project has three working sections, OC-II block, C-Block and D-Block These workings are operating in close proximity to the JR-5 Longwall Shed, 26-Dip Incline, other structures of 26-Dip, and a Township. There were complaints about ground vibrations and fly rock problems caused due to blasting operations, especially in OC-II and D-Blocks. In view of this, studies were taken up to eliminate the problems of ground vibrations and fly rock.

Jan 1, 2001

By K Taylor

Small scale tests have been conducted in blasting vessels in the laboratory, where the effects of explosive composition, charge diameter, explosive confinement as well as additives to the explosive were examined on NO, NO2, CO and CO2 production. Fumes were analyzed continuously using a flue analyzer, providing analysis every 15 seconds. The results were compared to previous work conducted in the laboratory and to literature findings. It was found that the type of the explosive was the most dominant factor with emulsion explosives producing significantly less amounts of toxic gases. ANFO was shown to always produce nitrogen oxides, even when fuel rich. Tests were also conducted by detonating explosives in broken rock, simulating the release of products of detonation during the formation of a muckpile. Products of detonation were affected by the presence of atmospheric air or rock around the charge. Gaseous products of detonation migrated through the rock piles at different rates, resulting in a change of toxicity values over time. In the small scale experiments, CO appeared to travel faster than CO2 while NOX was not identified. Analysis of the gases that were released during digging, several hours after the blast, resulted in high temporary concentrations of toxic fumes.

Jan 1, 2014

By Deepak Vidyarthi

This paper deals with various measures adopted in protecting a conveyor duct (named after a Conveyor Belt that was numbered as ‘02’) housing a 1600 mm (63 inches) belt conveyor system in a large, heavily mechanized open cast iron ore mine, producing about 20.0 million tones of ore per annum.

Jan 1, 2008

By C E. Johnson, S Hosein

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as a consequence of the shock wave created by the detention of the explosive charge in a blast hole. In an attempt to evaluate these hypotheses, an investigation was undertaken over a 4-year period with the aim of determining the precise origin of air overpressure. The research was carried out at a chalk quarry in the North of England.

Jan 1, 2017

By L C. Taylor, H U. Lesiste

This paper describes a method for estimating the density distribution in the soil cap as a function of distance from its top at the time of impact with the target. It provides an estimate of the density distribution in the soil on the center line of the soil cap at the time of target impact for a single depth of burial of the charge and two heights of target and shows that, for the heights of target and the depth of burial considered, the thickness of the soil cap first increases from the in situ value and then decreases. The distribution of soil density along the centerline of the soil cap changes significantly with distance from its original position. These results can be used for validating hydro-code computations and the soil models used in the computations.

Jan 1, 2011

By Francisco Sena Leite, Vincius Miranda, PhD Machado Leite, PhD Pinto, Raquel Carvalhinha, Alexandre Julio, Dorival de Carvalho

Rock blasting, in particularly the drilling process, is one of the first processes in the stage of rock fragmentation and plays a fundamental role by influencing all the following stages. Given its importance, some proposals to optimize this process have been presented over the last few years. These proposals, while having different approaches, aim (in a large part) to minimize the costs of drilling and blasting respecting the limits of fragmentation required by primary crushing. Reviewing some recent articles leads us to an enriching experience, since the authors of these articles clearly model the problem, but do not address the mathematical solution of these models, which in turn, given their non-linear nature, have no directly and easy solution. Simple and even robust optimizers present in the market show different results and often do not converge to a single solution. To address this problem, an adapted gradient heuristicbased model was developed to try to find optimum values. Heuristics search for values of stemming, subdrilling, burden and spacing that minimize the costs of blasting and drilling. This search, which by the nature of the heuristic moves the solution in the direction of the gradient with maximum decrease to find optimal solution, found values that in turn, when compared with values presented by market solutions not only equaled them as, in some situations, even improved the proposed solution. The algorithm was tested and validated on the field, and although the results have already been presented in papers published in the last year by the authors of this paper, it is now presented with its mathematical formulation and comparison with the other solutions. This approach is expected to be able to improve (and even demystify) the process of pattern expansion and be the basis for future work in the continuation of the optimization process.

Jan 1, 2019

By G. Cavanough, A. Torrance

Emulsions have been developed for over forty years to become the most common water-resistant explosives used in the mining industry. An emulsion is a common commodity, with many examples in our day to day lives of one immiscible liquid dispersed in another. They have varying degrees of stability from a few seconds to years. What makes their application in explosives unique is twofold. They contain a high concentration of salts in the dispersed phase and also have a far larger volume of dispersed phase than continuous phase. The continuous phase contains at least 75% by weight of an oxidizer such as ammonium nitrate dissolved in water. The crystallization point of these solutions is often >60oC which means that the formation of the emulsion has to occur at an elevated temperature. Once the emulsion is cooled, its structure helps to prevent the formation of crystals in an otherwise unstable system. At room temperature there is a considerable potential for the small oxidizer droplets to crystallize which is countered by the strength of the oil layer and also the size of the emulsion droplet. If the emulsion droplet is too large then crystals can form which may lead to rapid deterioration of the emulsion and overall crystallization, accompanied by a temperature rise as the heat of crystallization is released from the emulsion. The size of the emulsion droplet is critical in preventing crystal growth and subsequent droplet coalescence and emulsion break down. One method of examining emulsions and understanding their structure is to use optical microscopy to measure droplet size and also emulsion deterioration from shearing, temperature cycling and when contaminants are introduced, such as detergents, different oil types, coating agents and dust particles. This paper reports on advanced techniques to quickly assess emulsion quality and stability

Jan 1, 2024

By Curtis G. Kremer

"New explosives initiation systems continue to be developed as new technologies make advancements possible. Due to recent initiator developments, explosives users now have the most reliable, accurate, safest and easy to use systems ever offered. Three initiation systems recentlyintroduced which offer significant improvement over standard electric and nonelectric initiation systems include Magnadet, EXEL high-strength shock tube, and Redundant two-Dath surface delay systems. These three systems will be discussed zn cecail with rmpiasis on their functioning, safety characteristics, ani specific application areas."

Jan 1, 1991

By P. O'Connell, J. Lever, C. Clemence

The Bulyanhulu Mine, Tanzania is constantly trialing ideas for improvements in the drill and blast process. The project work has resulted in a large number of choices in explosive type and charging methods being available for blast design. Interestingly, though booster sensitive bulk emulsion had been introduced to the site to reduce dilution, better results were being obtained from reduced charge columns (decoupled columns of poured anfo in 50mm pvc pipe) and pneumatically loaded anfo upholes, which had been traced. In order to compare the explosive type and charge up-methods, an explosives comparison trial was performed.

Jan 1, 2006

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

By Jack Elorenta

We often hear that, "Blasting was an art, but now blasting is now a science". 'Scientific' blasting implies that we have quantified and reproducible measurements of the feedstock and product of the blasting process. However, the industry's reluctance to adopt two key technologies, drill monitoring and optical size analyzers, sheds doubt on the claims of scientific blasting.

Jan 1, 2003

By August Ferraz Ribeiro, Guilherme Dias Mendona, Paula Henrique Lisboa, José Silvio Corsini

Correct slope adhesion is related to the conformity of the slope’s real geometry to slope planning. It is very important in mining because slope design has economic and safety implications. Slope design conditions can interfere with mining waste and ore proportion. Without a correct wall, the development of the mine can be hindered, which can reduce the amount of ore available. Furthermore, correct slope design reduces the possibility of melting and allows traffic with equipment and people in the mine. However, defining the wall is a more complex work as the characteristics of the rock require the use of blasting techniques. Therefore, Enaex Mining Technical Solutions (EMTS), in partnership with the engineering team at the Chapada Mine, at Lundin Mining, has developed this study in order to increase slope adhesion. The basis of this study is a near-field vibration test, which enables the creation of vibration attenuation law, and a seed wave damage model has allowed the characterization of the rock present at the Chapada Mine. Then, we could compare the model result to the real slope adhesion achieved with the buffer technique used in the mine. Therefore, it was possible to relate the real result to the model result.

Feb 6, 2023

By G. Walsh, M. T. Wild

In this paper the performance effects of linear shaped charges will be discussed. Different sized charges were tested and reviewed based on their performance used with a typical detonation method vs. detonation with a line wave generator. The goal of the project was to determine if the linear shaped charge had better performance with an ideally linear wave moving through it, verses a swept wave that is currently used. A line wave generator is a flexible sheet explosive formed into a triangular shape with holes placed in strategic places to cause a detonation wave to become linear across the width of the triangle. A standard linear shape charge with a detonator in the side of the charge was be detonated against a witness plate to get a standard depth of penetration. A second standard linear shape charge with a detonator connected to the top of a line wave generator, the line wave generator placed on top of the linear shape charge, was be detonated against a witness plate to get a comparison depth of penetration. All charges had a standoff 1.5 times the width of the cavity, allowing the data to be compared to the control charge. Computer modeling was intended to be used to predict the results from testing these designs in the field. The actual results were compared among themselves.

Jan 1, 2011

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By Robert Hopler

CHAPTER I. DEFINITIONS AND CLASSIFICATIONS. Definition of Explosives. SECTION 1. The term “Explosive” or “Explosives” whenever used in this ordinance, shall be held to mean and include any chemical compound or mechanical mixture that contains any oxidizing and combustible units, or other ingredients, in such proportions, quantities or packing that an ignition by fire, by friction, by concussion, by percussion or by detonator of any part of the compound or mixture may cause such a sudden generation of highly heated gases that the resultant gaseous pressures are capable of producing destructive effects on contiguous objects or of destroying life or limb, and includes all the articles specifically mentioned in Section 3 herein, and all other similar articles

Jan 1, 2013

By Lon Santis, Michael Swisdak, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc. (APT) have developed a quantitative risk assessment tool called IMESAFR (IME Safety Analysis for Risk) for managing risk from various activities undertaken in the commercial explosives industry. The first version was completed in 2006 and Version 2.0 of the software was completed in 2012, incorporating several major new features. The platform is now based on a Geographic Information System (GIS), providing a bird’s-eye-view to help visualize facility layouts and risk. Spatial data on potential explosion sites and exposed sites can now be automatically transferred from the images to ease users’ data input. Use of GIS data provides the ability to check facility compliance with quantity-distance (QD) standards such as the American Table of Distances (used by the Bureau of Alcohol, Tobacco, Firearms and Explosives, ATF), the NATO standard (used by Natural Resources Canada and other nations), or a user-defined table. Research conducted and knowledge gained over the last 10 years enabled changes in the algorithms and models that provide greater fidelity and reduce conservatism. Expert users can change global settings to more accurately match actual site conditions and the program runs using either Imperial (English) or SI (metric) units of measure. These changes and other new features are discussed and demonstrated.

Jan 1, 2013

By C. Navalkar

Systematic drilling & blasting techniques are currently being viewed in the mining & construction industry as a correct 8z scientific approach for optimization process in rock excavation, as drill & blast costs usually represent major share in total cost of production and also the environmental impacts plays an important role in designing of the operations. Designing a blast is a complex planning task, which for optimization, includes deciding the bench geometry with respect to the rock properties & geology of the area, capacity of the excavators, choice of explosives & detonation method, tiring sequence, etc. Optimization of blast design needs a detailed comprehensive study of all the above intersecting elements. Preblast & Post blast surveys are required for further improvements in blast designs. However, the choice of blast design depends upon the the requisite blasting results opted for and the cost you are ready to pay for the same. The blasting operation, in general, also involves numerous side effects namely, ground vibrations, fly rocks, dust, noise & gas pollution, air blast effect etc. Again these effects can be made tolerable up to a certain extent depending upon the limitations of the environmental obligations as may be specified by the concerned authorities.

Jan 1, 2001

By Dr. Calvin J. Konya, Anthony Konya

Beginning on the Niagara Power Project, presplitting became a widely used blasting technique to obtain smooth walls in mining and construction projects reducing scaling, creating more stable pits, allowing the application of slope steepening to reduce waste removal and increase mining depths, and increasing the safety of mine and construction workers. This technique has been minimally studied in comparison to production blasting and currently two separate theories are present on the mechanics behind the presplit. The first is that shockwave collisions between boreholes cause a tension zone to develop causing the split formation. The second is that gas pressures build in the boreholes causing hoop stresses between holes leading to a presplit formation. Practical blasting methods in presplitting such as propellant presplitting and precision presplitting would not be applicable based on the shockwave theory yet are widely used and documented in the industry. Along with this, modern research using a borehole simulation device and advanced pressure gauges have allowed the authors to obtain true borehole pressures in decoupled blastholes. This paper will present this research which correlates the borehole pressure to variables such as the Young's Modulus and Tensile Strength of various rock types giving blast designers the ability to design a presplit to function in many rock conditions, including weak rocks such as siltstones and mudstones.

By A. K. Mishra

The mineral industry is leading towards a technology driven optimization process. Drilling and blasting are such unit operations in a mine, which can alter the balance sheet of the mine if not planned properly. The development, improvement and utilisation of innovative technologies in terms of blast monitoring instruments and explosives technology are important for cost effectiveness and safety of mineral industries. The ever-growing demand of mineral has compelled the industry to adopt mega opencast projects with big equipments. This has necessitated use of few hundred tonnes of explosives in each blast. The bulk delivered fourth generation explosives has solved the problem of explosive loading to a large extent. The priming of bulk delivered explosives in Indian mines uses the conventional PETN/TNT based cast boosters. As the conventional cast booster possess safety problems in terms of handling and use, so Indian Explosives Ltd., has developed an emulsion based cast booster (Powergel Boost).

Jan 1, 2005