Search Documents

By Kenneth D. Winters

This Bureau of Mines report presents a Fortran IV computer program for the structural analysis of (1) protective canopies used in underground mines to protect equipment operators from roof falls and (2) rollover protective structures (ROPS) used in surface mines to protect equipment operators during vehicle overturn accidents. The program, entitled PLASTIC CANOPY, permits rapid and inexpensive calculation of the ultimate strength and deformation characteristics of a canopy for a variety of static loading conditions. The structure is modeled as a series of interconnected beam and/or plate elements. Stresses in, and displacements of, each structural element are computed and printed out at the yield strength of the canopy, at several intermediate load levels between the yield and ultimate strength of the canopy, and at the ultimate strength of the canopy. Other features of the program include prediction of buckling of a beam member under combined axial compression loading and bending, plotting of the input geometry of the structure, and plotting of the deformed shape of the loaded structure. Program description, input instructions, program listing, and four example problems are included.

Jan 1, 1979

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

By Forrest T. Moyer

All general measures of the safety record of the coal mining industry worsened appreciably in 1970. Injury experience for the year was 260 fatal and 11,552 nonfatal injuries at respective frequency rates of 1.00 and 44.40 per million man-hours of worktime. The fatality total was 57 higher and the rate of occurrence was 18 percent higher than the corresponding figures of 203 fatal injuries with a frequency rate of 0.85 in 1969. The worsened fatality record in 1970 resulted primarily from a major disaster (a single accident which results in the death of five men or more) on December 30, 1970, that killed 38 men. There were no major disasters in 1969. The total of 11,552 nonfatal injuries in 1970 was the highest annual total since 1960. It was 1,635 higher and the frequency rate was 6 percent higher than the corresponding totals for 1969 of 9,917 nonfatal injuries occurring at a rate of 41.76. The injury severity rate of 8,308 days lost or charged per million man-hours was 13 percent worse than that of 7,359 in 1969. Similarly, the average severity of 183 days lost or charged per injury in 1970 was 10 days or 6 percent higher than in 1969. Aggregate worktime of 260.2 million man-hours and production of 609.8 million tons in 1970 were, respectively, 10 and 7 percent higher than in 1969. An average of 144,480 men were at work on an average of 227 active days in 6,316 mines and 544 mechanical cleaning plants during 1970.

Jan 1, 1973

By Theodore M. Katz, W. Stephen Brightwell, David E. LeGrande, Joseph J. Hurrell, Jane A. Lipscomb, Nancy Lessin, Lawrence R. Murphy, Michael J. Colligan, Steven L. Sauter, Richard A. Lippin

Revolutionary changes in the organization of work have far outpaced our knowledge about the implications of these changes for the quality of working life and for safety and health on the job. This gap in knowledge is one of the 21 priority areas for research under the National Occupational Research Agenda (NORA)—a framework crafted by the National Institute for Occupational Safety and Health (NIOSH) and its partners to guide research into the next decade. This report was developed under NORA as the first attempt to develop a comprehensive research agenda for investigating and reducing occupational safety and health risks associated with the changing organization of work. Research and development needs identified in the agenda include (1) improved surveillance mechanisms to better track how the organization of work is changing, (2) accelerated research on safety and health implications of the changing organization of work, (3) increased research focus on organizational interventions to protect safety and health, and (4) steps to formalize and nurture organization of work as a distinctive field in occupational safety and health.

Jan 4, 2002

By James E. Hill

Tremendous improvements in mining technology have been witnessed during the past 100 years. For example, before 1860 all blastholes were drilled manually and blasting was done with low-energy black-powder. During the 1860's both the pneumatic rock drill and high-energy dynamite were introduced, ushering in an era of mining mechanization that has steadily progressed since that time. Today, with the rapid implementation of the latest advances in communication science, mining technology is moving into a new era that goes beyond mechanization as such. Transistors, transducers, scanners, telemetry, and the like, all terms largely derived from the new communication sciences, add up to what is popularly know as automation-the communication of machine with machine. Automation is now playing an important role in selected parts of the mining process, such as hoisting, hydraulic roof supports, and underground surface locomotive haulage and belt conveyor systems. But this year marked the first attempt to auto-mate the total mining process with the commencement of production at the British National Coal Boards Bevercotes mine. If this full-scale experiment proves successful, it could lead towards other fully automated mines in both Britain and other parts of the world. This decade, there-fore, could be considered the one that provided the foundation for the mines of the future.

Jan 1, 1966

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

This final report summarizes the effort on a very aggressively scheduled and demanding development program undertaken by Westinghouse for the U.S. Bureau of Mines under Contract No. H0101262. The objective of this program was to produce hardware and test it to determine the efficacy of certain concepts of Coal Mine Rescue and Survival as established by the request for proposal and the study performed for the U.S. Bureau of Mines by the National Academy of Engineering (NAE). (These are stated in paragraph 1. 1 for reference.) In carrying out this program, Westinghouse provided specific hardware designs in consonance with the objectives of the concepts outlined in the NAE study final report. Though this contract did not require producing final design hardware ready for introduction to the coal mining community, components of the CMR&SS - as delivered - have some value in disaster situations and are to be kept on standby alert. Additional design and production development is required and should be undertaken on most of the subsystems and components before they can be used in the competitive coal mining community.

Jan 1, 1971

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By V. B. Dale

This paper is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits of New Mexico. Most of the descriptions are from field examinations by the senior author. Reported tungsten occurrences that were not visited are listed below: Colfax County: Occurrences of ferberite in thin veins in Willow Creek near Elizabethtown.4/ Dona Ana County: Small, low-grade occurrences of scheelite near the summit of the Organ Mountains about 15 miles east of Las Cruces. Hidalgo County: Scheelite reported in the Daisy mine 7 miles southeast of Hachita. Ores are carbonates containing copper, gold, silver, and bismuth.5/

Jan 1, 1959

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By Melford H. Salsbury

The maximum net return from the sale of ores and concentrates of gold, silver, copper, lead, and zinc accrues to the producer when these mine products are marketed to the best advantage. Data are presented that the producer, especially the small mine operator, can use to survey available markets and make a preliminary estimate of the net return to be expected from an ore, on the basis of typical mill, smelter, and freight schedules. A review of the industry is presented by States in which recent production statistics are given, marketing facilities are discussed, and locations of principal mining districts, custom mills, and smelters are shown. Explanations of treatment processes, ore types, treatment charges, payments for metals, and deductions are given. Published rail and truck freight rates for mine products, based on marketing patterns developed over many years, are listed and explained.

Jan 1, 1964

By F. S. Crawford

Although it may be impracticable to adopt standard methods of safe working in all branches of mining, and although it may be impossible to establish a standard for each class of work at each mine, some of the iron-mining companies in the Lake Superior district have found that by adopting certain standard ways of performing certain of their operations they insure both more efficient and safer working conditions. Many companies have adopted the idea that the safe way of doing things is also the most efficient and economical way, and, through the medium of their safety conferences they are trying to find the safest way, and the most efficient way, of performing practically every operation about the mines. This activity will, undoubtedly, be continued at every operation which uses this method of doing safety work, because in the advance of industry changes must be made in the results required from time to time. A review of the safety standards and safety suggestions which have been arrived at by some of the companies in this the greatest iron-mining district in the world, will be of value to companies who are interested in improving the safety of their working conditions. So that attention may be directed to the methods in use, rather than to individual companies, all names have been omitted and companies are referred to only by letter.

Aug 1, 1931

By W. W. Adams

"The eighth National Safety Competition, that for 1932, conducted by the United States Bureau of Mines, was participated in by 322 mines and quarries operating in 34 States. Tables 2 to 6 show the relative standing of the various plants. Bronze trophies, known as the 'Sentinels of Safety,' which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were awarded to five companies, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, - namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or open-cut mines. The trophies are awarded for one year and are then transferred to the winners of the succeeding year's contest.The trophy for bituminous-coal mines, which has been in New Mexico for the past year, was won by a mine in West Virginia. The metal-mine trophy goes to New York State for the first time in the history of the contest. Previously it had been won by mines in Minnesota, Michigan, Kansas, and Oklahoma. The trophy for nonmetal mines remains for another year at Retsof, N. Y.; that for quarries and open-cut mines is transferred to a quarry in Michigan. The trophy for anthracite mines, of course, remains in Pennsylvania, as all anthracite mines in the contest are in that State.In determining the relative standing of the various companies enrolled in the competition, all mines and quarries were graded according to their accident-severity rates, - that is, according to the number of days of disability of employees on account of accidents in proportion to the number of man-hours of work done by all employees at the plant. Reports of accidents and of man-hours worked were furnished by the companies to the Bureau of Mines. These reports were carefully examined and classified to insure uniform weighting of accidents according to the number of days of disability to be charged and to insure uniformity of methods of calculating the accident-severity rates for the various mines and quarries. When the relative standing of all plants had been determined in this way, a summary of the records of the companies having the lowest accident-severity rates in their respective groups was sent to the members of a committee of award for examination in accordance with the rules governing the safety contest. The members of the committee of award were W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining engineering of Columbia University; C. B. Huntress, executive secretary of the National Coal Association; A. J. R. Curtis, assistant to the general manager of the Portland Cement Association; and A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association. When two or more mines within the same group operated without an accident during the year, the contest rules provided that the trophy for the group should be awarded to the plant whose record showed the largest number of man-hours worked."

Jul 1, 1933