Search Documents

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 118-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By W. H. Tomlinson

This publication presents the basic text for a 20-hour accident-prevention training course developed for supervisors by the Federal Bureau of Mines. During the past 2 years, the course has been used by the Bureau in teaching more than 300 groups of coal-mine supervisors-men whose responsibility is twofold: To manage in production and maintenance phases of coal mining and to guide their men along paths of safety. This is a handbook for teaching teachers. In this handbook will be found references to safety practices followed by companies that consistently have low accident records. These companies credit their outstanding performance to the adoption and faithful observance of accident prevention by supervisors and workers alike on a wholesome, cooperative basis. Teaching safety to workers involves both on-the-job and classroom-type instruction. If such training is to be permanently effective, it must be reinforced consistently on the job by the immediate supervisor of the worker. This publication is intended to provide such a supervisor with the motivation to provide such follow-up and shows how he can accomplish it effectively.

Jan 1, 1962

By S. J. Davenport

The increased consumption and importation of fluorspar and cryolite (1)3/ in recent years, and especially the addition of fluorine compounds to drinking water in the United States, have aroused renewed interest in the properties of such compounds and possible health hazards incident to their use. It has been suggested that the issuance of a revision and elaboration of Information Circular 7311, The Hazards of Hydrogen Fluoride Poisoning in the Mineral and Allied Industries, which hay been out of print for some time, would be opportune. Fluorine minerals have been known since the Middle Ages. Fluorine was isolated in 1886 by Moisson (2).

Jan 1, 1954

By G. B. Shea, R. A. Cattell

This resume of the work of the Petroleum and Natural - Gas Division of the Bureau of Mines for the fiscal years 1940 and 1941 is the second of a series. of progress reports . It brings forward from the 1939 annual report information on the course of activities of the division in carrying out its objectives of increased conservation and better utilization of petroleum, natural gas, and related resources through a coordinated program of research and fact - finding . It discusses, also, special assignments. executed for other Government agencies, which in recent years have constituted a considerable part of the division's work ." . In the present national emergency, in which petroleum is so essential , many of the Bureau's research activities bear directly on the availability, conservation, and use of petroleum for national defense . Accordingly, during the past year attention has been focused for the most part.on.problems associated with the needs of national defense . Several long-time researches , which in themselves are potential sources of desirable knowledge , were judged to be of secondary importance under present conditions and accordingly were suspended . Studies also were oriented in line with rapidly changing conditions to meet the demand for accurate findings on short notice . The Petroleum and Natural - Gas Division has experiment stations at Bartlesville , Okla . , and Laramie, Wyo . , a field office at Dallas , Tex . , and a field office and laboratory at San Francisco , Calif . It also operates the Government helium plant near Amarillo , Tex. In addition to the helium operations , some of the petroleum and natural - gas research activities are conducted at the Amarillo plant .

Feb 1, 1942

By Gregory R. Wagner

The Program of Mine Safety and Health Research described in this document reflects the continuing commitment of the Spokane and Pittsburgh Research Laboratories to focus on the most important areas where research can make a difference in reducing risk and improving safety and health for miners. It is the first program of work conducted since Congress mandated closure of the former U. S. Bureau of Mines (USBM) in the Department of the Interior and supported integration of the health and safety research function of the former USBM into the National Institute for Occupational Safety and Health (NIOSH). Organizational changes made FY97 a challenging year of transition. Ongoing research was reviewed and revised to reflect the new, more limited, health and safety mandate of the research laboratories. The mining industry, mine worker representatives, and interested government agencies provided broad input to assure that the research performed would focus on the most critical safety and health problems confronting mining today and which are expected to be faced in the future. The two laboratories worked to evolve coordinated programs of safety and health research, each with a special focus. The work of the Spokane Research Laboratory is directed toward issues of special importance to the Western mining industry, particularly those safety hazards found in metal/nonmetal mining and surface mining. The work of the Pittsburgh Research Laboratory will continue to focus on Eastern mining, particularly underground coal mining. Traditional areas of expertise for understanding and preventing fires and explosions and for controlling the hazards of dust and noise will continue to reside in Pittsburgh. Each laboratory is developing new capabilities in the analysis of relevant safety and health information to assure that program priority-setting decisions are informed by the best available data. Recognizing the continuing importance of communicating the results of research to all who are capable of improving safety and health conditions in mining, each laboratory has developed an activity for information dissemination and coordination with stakeholders. In the midst of organizational self-examination and change, the research staff in Pittsburgh and Spokane have never wavered from their continuing commitment to conduct the highest quality scientific research-solution-oriented scientific work meant to reduce the risk of injury, disease, and death from occupational hazards in mining. The pages that follow give insight into some of the program activities and accomplishments from FY97. I hope you share my pride in the many accomplishments of the NIOSH mine safety and health research program during this year. This report comes at a time of increasing stability for the mine health and safety research program. The organizational changes in Spokane and Pittsburgh have been concluded, and NIOSH has succeeded in recruiting a new, permanent associate director for mining to lead this critically important national program. Congress has contributed to an optimistic future by providing expanded funding for NIOSH mining-related research for the next fiscal year. On a personal note, I greatly appreciate the opportunity I have had to serve as the NIOSH Acting Associate Director for Mining during this transitional year. The commitment and intelligence with which the mining research staff pursued their mission was matched by their patience and understanding in moving into a new organizational environment. All of us committed to improved safety and health for this Nation's miners owe them our respect and appreciation.

A pilot program was undertaken to evaluate a process developed by the U.S. Bureau of Mines to recover nickel, cobalt, copper and chromite from domestic nickel laterite resources. An existing five ton per day pilot plant was modified to accommodate treatment of laterite by the Bureau process, which employs reductive roasting, ammoniacal sulfate leaching, solvent extraction, and electrowinning to extract, separate, and recover nickel, cobalt and copper as high purity cathode products. Three distinct types of laterite i.e., limonite, saprolite and a mixture of limonite/saprolite were processed through the plant during three operating campaigns. Nickel cathode was made during all three campaigns, while cobalt cathode and chromite concentrate were recovered only during processing of limonite. Leach extraction of nickel and cobalt averaged 83 and 67 percent, respectively, while the overall recovery was 80 and 63 percent for nickel and cobalt, respectively. Initially, over-reduction of iron in the saprolitic calcine contributed to poor settling of the leached solids. This problem was overcome by careful control of reducing conditions and flocculant addition. An economic feasibility study was made for a 5000 TPD grassroots laterite processing facility scaled-up from pilot plant data. Estimated (+ 30) percent capital cost for a Nine and plant is $367 million with an estimated $103 million per year operating cost. The study indicates that low-grade domestic laterite may he processed with marginal profit- ability.

Jan 1, 1982

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989

By Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular industry or commodity. 2. Recirculation is dependent on the processing requirements of a particular commodity, the manner in which the water is used, cooling and condensing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

Jan 1, 1966

By S. Kodama

Starting on a small scale, the equipment for processing synthesis gas to form liquid hydrocarbons was expanded to handle 100 m) 3/hr. This reactor was successfully designed and constructed, and a basis for future design methods was established. Because, however, this work was carried out on an empirical basis, it is felt that a more thorough theoretical study should be made in an effort to increase the efficiency of the process, particularly in the development of a simpler converter.

Jan 1, 1951

By William H. Schiffbauer

The Bureau of Mines is conducting research that is aimed at making the mining industry more efficient in term of both productivity and the health and safety of the worker. As part of this research the Bureau of Mines has integrated a testbed composed of computer and related peripheral hardware to form an intelligent base for performing autonomous mining machine experiments. Although this particular application was con- figured for use on a Joy 16 CM mining machine, its generic structure facilitates its attachment to a variety of mining machine types. The multitasking multiuser computer can be set up for other applications by changing a bubble memory cartridge. The Joy 16 CM implementation includes 96 digital input-output (1-0) ports, 32 analog inputs, 8 analog outputs, 2 serial data channels, and 1 printer port. Operation of the machine can be performed either through a local terminal or remotely through a modem hookup. This report describes a testbed for autonomous mining machine experiments (TAMME)--its hardware, software, and complete system integration--so that it can be used as a foundation for other applications.

Jan 1, 1988

By C. A. Hesse

The Quartz Hill Molybdenum Project, In Southeast Alaska, was the first mining project to attempt the permitting of a submarine tailings disposal system in the United States, since the passage of the National Environmental Policy Act of 1969 and the Clean Water Act of 1977. Over $20 million was spent by the project developer in baseline data gathering and In funding the preparation of the four Environmental Impact Statements and other environmental documents required at various stages of the project between 1977 and 1988. Because of the timing and a unique set of environmental, legal and regulatory requirements which applied to this project, innovative approaches were developed. This report describes those requirements and the developments, and gives a full historical account of the campaign for permitting submarine tailings disposal at Quartz Hill, until denial of the NPDES permit application by EPA in September 1 990. The extensive studies done for Quartz Hill suggested that under certain conditions the selection of submarine tailings disposal can be the overall environmentally preferred alternative for a mining project. The Quartz Hill story illustrates the complexity of the existing permitting structure and paints out the desirability of rationalization to achieve a more effective system.

Jan 1, 1993

By William H. Pomroy

This report describes Bureau of Mines research that led to the design, prototype fabrication, and successful proof-of-concept testing of an improved stench fire-warning system for underground noncoal mines. Stench systems are the most widely used means of warning driers in underground noncoal mines of fires or other emergencies. A stench system alerts miners that an emergency condition exists by injecting an odorant into the mine air. Although stench warning systems have been used successfully for over 60 yr, present systems suffer several serious shortcomings, including odorant toxicity, unreliability of warnings, widely varying stench concentrations, and others. In 1980, the Bureau began a research program to upgrade the stench warning system. The resultant system overcomes the deficiencies of existing systems by substituting tetrahydrothiophene for the commonly used ethyl mercaptan stench odorant, and through the use of a specially designed stench injector. The improved injector reliably meters stench fluid into either ventilation-air or compressed-air streams at a precisely controlled rate. Prototype hardware has been fabricated and proof-of-concept tested under bath laboratory and in-mine conditions.

Jan 1, 1985

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By W. G. Pariseau

A two-dimensional finite element program has been modified and extended to account for some of the rock mechanics complexities associated with single entry development of longwall coal mine panels. Program capability includes arbitrary assignment of element properties without regard to element ordering, anisotropic elastic, plastic and brittle rock properties that may be time dependent (aging), arbitrary mining sequences and provision for the effects of artificial support on the adjacent strata. Failure is according to an extended von Mises criterion that may be linear or quadratic in form; flow rules are obtained from the yield function taken as the plastic potential, but brittle behavior is treated as a discontinuous process of material properties change with deformation. In either case the extent of failure is calculated from the external boundary conditions. Application of the program to essentially two-dimensional problems resulted in lose agreement between calculated displacements and field measurements in the double entry system. Bleeder entries were stable in one locality and not in another. Artificial support had little influence on stability.

Jan 1, 1978

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

By W. M. Myers

Jet is a substance of organic origin and has been defined by the U. S. Geological Survey as a "dense black lignite, taking a good polish, and sometimes used for jewelry". Jet is characterized by the lustrous, intense black surface it displays when polished. It is due to this property that the expression "jet black" is so commonly used to imply intense blackness.

Jan 1, 1923