Search Documents

By Donald P. Schlick

This Information Circular presents a brief historical digest of the early attempts of the Bureau of Nines and the U.S. Public Health Service to establish coal mine dust exposure standards. It reviews current, accepted standards of the United States as well as available standards of other countries.

Jan 1, 1971

By R. W. Barnes

This circular presents results of a survey conducted by the Bureau of Mines to ascertain the extent to which dust-control practices are employed in the coal-mining industry. This survey was initiated because of increasing realization of the possible harmful effects of the inhalation of dust upon the health of coal-mine workers and the advent, during recent years, of new types of mining machinery and new mining methods that may have a direct effect upon the extent of exposure to airborne dust experienced by persons mining coal. Anthracite Mines The survey covered 169 anthracite mines that were operating from November 1, 1953, to July 1, 1954. It showed that large mines employing more than 100 men were doing most to control dust produced during mining.

Jan 1, 1956

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By Erle C. Donaldson

Subsurface injection of liquid and slurry-type industrial waste is being used as a means of waste disposal. This survey conducted by the Bureau of Mines shows that the method can be economically and environmentally attractive if the proper precautions are taken, especially when the alternative is cursory treatment and discharge at the surface. Attention is called to petroleum technology and experience that can be applied to subsurface waste injection. Part 1 of this report is a discussion of the general aspects of subsurface waste-injection systems. Part 2 is a general discussion and review of the literature concerning the geologic formations available for injection in the United States. Part 3 is a discussion if 15 case histories including information on the source and nature of the waste and the geology, surface equipment, well completion, and operation of the systems.

Jan 1, 1974

By Oliver C. Fursman

The Bureau of Mines undertook this investigation in order to determine the feasibility of producing commercially acceptable alumina and iron by application of the Pedersen process to high-silica, high-titania, ferruginous bauxites of the Pacific Northwest. Calcium aluminate slags were produced by smelting bauxite with coke and lime in an electric-arc furnace. Over 90 percent of the total alumina can be extracted by sodium carbonate solution from slags of properly controlled ternary-phase composition (CaO-Al203-SiO2) that are cooled slowly enough to permit adequate crystallization of the 2CaO-SiO2 and the calcium aluminate compounds. Most of the iron charged was recovered in the regulus; the slag contained about 2 percent iron (as iron oxide), regardless of smelting time.

Jan 1, 1968

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"INTRODUCTION An extensive test program is in progress by the Bureau of Mines to determine ways and means of recovering ferromanganese-grade ore 6/ from the wide-spread domestic manganese and manganiforous iron deposits. Samples for testing were received from the Interstate Manganese Co. in northeastern Tennessee, 11 miles west of Mountain City and 10 miles southwest of Damascus Va. The ore deposit occurs in the residual material of the Shady dolomite 7/ as an unconsolidated mixture of hard and soft manganese oxides and clay.Numerous tunnels and pits have developed a large reserve of ore in an area of about 15 acres. One pit 250 by 50 by 20 feet is being mined by rower shovels. The ore is hauled to a washing plant for log-washing, hand-sorting, and jigging. Coarse concentrates from the washing plant are marketed without further beneficiation.ACKNOWLEDGMENTSThe authors wish to acknowledge the assistance of R. F. Fisher, who made the roasting and magnetic tests."

Mar 1, 1942

This publication contains eight papers presented at a Bureau of Mines Technology Transfer Symposium in Charleston, W, on June 22, 1983, Five of the papers describe the results of Bureau-sponsored research on cabs and canopies for low-coal underground mining equipment. The other papers describe the efforts of three underground coal mining equipment manufacturers (FMC, Joy, and Lee-Norse) in the area of cab and canopy design.

Jan 1, 1985

By Joseph Gersic

MINFO has been developed to serve as a frontend for three databases created to store basic minerals information gathered during the minerals resource assessment conducted by U.S. Bureau of Mines(USBM) for the Malheur and Jordan resource areas of southeastern Oregon(MJRA). The primary database is the Minerals Location Inventory (MLI.DBF) which contains of information assembled from field work performed during this project, the USBM Minerals Availability System/Mineral Information Location System(MAS/MILS) database, the Oregon Department of Geology and Mineral lndustries(DOGAMT) Mineral Information Location(MILOC) database, and the U.S. (Geological Survey(USGS) Mineral Resource Database System(MRDS), In addition, assay results are contained in the geochemical database (ELEMENTS.DBF) and modified X-ray diffraction analysis information is contained in the minerals database (MINOR.M.DBF). MINFO includes four types of program modules: ? Enter/Edit Data was developed to allow the addition of new information and to encourage correction of errors by providing a convenient means of entering and editing data and a large degree of automatic checking and filtering of entries. ? ACAD/DBF Link links each site symbol posted on the map in the drawing file to a record in the database. This provides the user with the ability to use a mouse or other pointing device to graphically select a site for viewing and editing. Edits are performed directly in the database file, ? Reports contains 7 formats of data output for creating files for printing, transfer to other database formats, and exporting to other software packages such as spreadsheets and word processing programs. ? Maps includes 5 programs for creating AutoCAD script files which can be used to create maps of selected information in conjunction with AutoCAD. Mineral location mapping files derived from MLI.DBF can be created in 2 formats. Mapping files can be generated from each of the 2 sets of geochemical analyses contained in ELEMENTS.DBF. X-ray diffraction analyses can also be translated into instructions for creating and posting piecharts at sampling sites.

Jan 1, 1994

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

By N. A. C. Smith

The Bureau of Mines motor gasoline surveys have been conducted in January and July, during 1920 and 1921. The Bureau has obtained and analyzed samples of gasoline representative of that marketed in the larger cities. These surveys have indicated that the gasoline on the market during the winter months is more volatile than that sold during the summer months. Naturally, the motorist desires a more volatile gasoline in the cold winter months, as it affords greater ease in starting. The fourth semi-annual motor gasoline survey, conducted during the month of July, shows an interesting relation between the market price and the quality of motor gasoline. This is particularly evident if figures obtained today are compared with those of a year ago. At the time the Bureau of Mines conducted its summer survey of motor gasoline last year, the average tank wagon price of gasoline was 28.2 cents per gallon. This year it was 21.2 cents, a drop of practically 25%.

Jan 1, 1921

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By Alla D. Mah

Titanium forms several compounds with oxygen and also is able to dissolve interstitially about 33 atomic percent of oxygen. Starting with titanium dioxide, reduction becomes increasingly difficult as oxygen is removed; and the final step, be reduction of the titanium-oxygen interstitial solutions, is by far the most difficult. The possibility of reducing titanium oxide, or of purifying titanium containing oxygen, by treatment with certain more volatile metals has been a subject of considerable interest. Theoretical appraisal of the limitations of this possibility, however, has been hampered by lack of adequate information on the thermodynamic properties of the titanium-oxygen solutions. The purpose of the present work was to remedy this difficulty by expanding the thermodynamic knowledge regarding these solutions. The experimental work involved three types of calorimetry and furnished the following information: (1) Heats of formation of 11 titanium-oxygen solutions, in the range of 0 to 10 wt.-percent oxygen, were determined at 298.15° K. As a byproduct, an improved value of the heat of formation of rutile was obtained, which, in turn, led to improved values of the heats of formation of the lower titanium-oxygen compounds. (2) Low-temperature heat-capacity data and entropies at 298.15°K in were determined for 2 representative titanium-oxygen interstitial solutions. (3) High-temperature heat-content data were obtained for 2 titanium-oxygen interstitial solutions to about 1,600° K.

Jan 1, 1957

By J. K. Whyatt

During the past 2 years, U.S. Bureau of Mines (USBM) researchers reviewed an in situ stress investigation conducted in 1977 at a test site on the 4250 level of the Lucky Friday Mine, Mullan, ID. Although the field measurements of over core strain were found to be useful, significant deficiencies were found in the stress field estimation procedure. The stress field estimate was then updated to incorporate recent progress in statistical capabilities and new understanding of stress concentration factors for doorstopper cells, as well as to correct an error in the original stress solution procedure. Simple models were used to examine the possibility that systematic variations in material properties and stress fields existed at the site. These models succeeded in reducing the sum of squared error somewhat, but fell short of completely describing stress variations throughout the test site. This overcore measurement will be supplemented by two other measurements described in the second and third reports of this series. Other observations of stress field characteristics are discussed in the fourth report The final report will also characterize the natural in situ stress field in the vicinity of the Lucky Friday Mine. This work was undertaken to support USBM research on mining method design and rock-burst control for deep mines.

Jan 1, 2010

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to considerable expense in testing such coals as may be available. In general it will

Jan 1, 1942

By N. M. Safaya

Moderate to acute deficiency of plant available phosphorus is very common in western coal mine spoils and topsoils. Although some of the spoils are known to contain seemingly adequate amounts of total phosphorus, the plant available phosphorus is so low that it constitutes a serious plant growth limiting factor in the mined lands. For the revegetation of these spoils, the use of species, varieties and ecotypes exhibiting greater efficiency for P uptake and utilization, or conversely, lesser susceptibility to P deficiency would be highly desirable. To identify such plants, quick and adequate methods of screening germplasm should he available. In the present growth chamber study several plant species were screened using continuous flow culture and spoil culture systems to provide information on their relative susceptibility. In flow cultures, P was maintained at 0.25, 2.5, and 25 moles; while in spoil cultures it was applied at 0, 25, and 75µg/g to a P-deficient spoil. Phosphorus deficiency symptoms appeared in alfalfa cultivars, birdsfoot trefoil, emerald crownvetch and yellow sweetclover within 7-10 days upon transfer of their seedlings to U.25 or 2.5 µM P solutions. Burning bush and Russian thistle, found abundantly as pioneering species on mine spoils, showed no deficiency symptoms; their shoot dry matter yield in the 0.25µM P treatment was 24% and 36%, respectively of their maximum yield obtained with 25 µM P. However, the percent increase in the dry matter yield of legumes with 0.25 µM P ranged from 7-13% over their maximum yield. With the increase in solution P concentration, the root dry weight ratio in the legumes increased from an average of 0.22 to 0.43, while in the weeds from 0.14 to 0.30. The low susceptibility of Russian thistle to P deficiency was also demonstrated in the spoil culture experiment. Legumes showed greater response to P-fertilization on the spoil than did the two weeds. With increasing concentrations of P in the solution, the root weight ratio of all the species decreased. At 25 µM P, weeds invested only 14% of their total dry matter yield in the root fraction, where as legumes and grasses invested as much as 24% and 33% respectively. Weedy species averaged higher P concentrations than the legumes and grasses. The mean P concentrations of alfalfa cultivars were the lowest among legumes. In general, P concentrations increased with the increase in P supply. In the flow culture system, P supply increased the Ca levels of legumes. The mean Mn concentrations were highest in the weedy species. The increases in P supply decreased Zn levels in all of the species. File effects of P fertilization on the tissue concentrations of Mn and Zn in spoil culture were similar to that of flow culture system. From this preliminary study, it may be concluded that the continuous flow culture system is efficient in rapid screening of a large number of species under controlled conditions for their efficiency in adapting to mineral stresses.

Jan 1, 1982