Search Documents

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

By J. W. Adams

Two different techniques were wed to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 1, 1974

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

By Charles E. Whieldon

Data on the oil fields in Mahoning Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and com- piled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965

By Wesley T. Holmes

This report describes the second phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected synthetic slag compositions in the Ti02 -A1203 -FeO-Si02 -CaO-MgO system. Both the hot-stage microscope and the strip furnace (melting-holding-quenching technique) were used during test procedure to determine the effects of CaO, MgO, and SiO2 on the liquidus temperature of slags. The liquidus temperatures of slags studied ranged from 1,241° to 1,900° C. The lowest liquidus temperature for each Ti02 plus A1203 plus FeO weight-percent generally occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. In this investigation substitution of either CaO or MgO for SiO2 and MgO for CaO raised the liquidus temperature of more than 50 percent of the reported base slags when Ti02, A1203, and FeO contents were held constant. The results of this investigation may serve as guidelines for determining flux requirements in smelting a wide variety of titaniferous magnetite concentrates or ores.

Jan 1, 1968

This report presents the results of reconnaissance-level investigations of the mill refuse disposal systems for 15 plants throw-heat the conterminous United States. The sites visited represent a cress section f the copper, iron, lead and zinc, and phosphate industries' practices in the field of fine-grained refuse disposal. The reconnaissance-level investigations were carried out to gather supplemental data to tae in-depth studies of Kennecott's Magma and Phelps Dodge's Morenci tailings deposits and Kennecott's Chino leaching dump. The various sites visited were classified according to the different systems and techniques used by the mining industry. The probable effects and relationships between site conditions and disposal methods were determined and evaluated to the extent feasible by a reconnaissance level investigation.

Jan 1, 1974

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion, of

Jan 1, 1937

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ 7/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion of

Jan 1, 1937

By W. I. Nissen

As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pet S02. In this regenerable flue gas desulfurization (FGD) process, S02 is absorbed from cleaned and cooled industrial flue gas with a citric acid-sodium citrate solution. The absorbed S02 is subsequently reacted with H2S to precipitate marketable elemental sulfur and regenerate the solution for recycle. Laboratory investigations of process parameters provided information for designing larger scale continuous operations. Information gathered from operation of two pilot plants, one at a copper smelter and one at a lead smelter, confirmed the laboratory results. Data were obtained for design and construction of a commercial-sized demonstration plant at the George F. Weaton Power Station, Monaca, PA. A preliminary operation of the plant was demonstrated, under a cost-sharing Bureau-industry contract. This bulletin describes the citrate process and gives results of the laboratory, pilot plant, and demonstration plant studies, as well as corrosion investigations.

Jan 1, 1985

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By Donald W. Ross

Petroleum oils of widely different grades have long been clarified or decolorized by contact with fuller's earths. More recently, so-called activated clays have also been used for this purpose. Still more recently ouch clays have been used in the form of nodules termed "catalytic pellets." Clays of varied appearance and from different localities possess the desired bleaching qualities, but evaluation of such clays, so useful to the oil industry, has not been simple. Previous methods of identification and evaluation have largely followed procedures of production methods and were not primarily based upon the fundamental properties of the clays. Thus) a false assumption has grown up that) bleaching clays probably have no common properties on which a-method of comparison can be based. Fuller's earths and activated clays have a large absorptive capacity for the color constituents of petroleum and its products decolorizing is accomplished by bringing the oil into intimate contact with the clay and later separating the decolorized oil from the clay with its load of absorbed coloring matter. Former practice in absorbing "color" was to use the clay as granules or In' powdered form. More recent practice is to use clay pellets that are more abrasion-resistant than the granules. The oil is either filtered through a bed of clay, percolation method, or agitated on contact with the clay, contact method. Viscous oils are decolorized at an elevated temperature, so that their viscosity is lowered to the point at which thorough contact with the clay is insured. Nonhumidifying, nonoxidizing gas, such as dry steam or dry nitrogen, is used to seal such hot oil masses from the atmosphere.

Jan 1, 1948

By Charles M. Mason

The Bureau of Mines evaluated equipment and procedures for drop-weight testing of explosive liquids as prescribed by Test 4) a widely used method. It was demonstrated that partial ignitions, originally designated as negative results, should be designated positives; it was also shown that wear or erosion of the sample cups and the type of mount used for the apparatus had important effects on the results. Relative sensitivity as measured by Test 4 was found to vary slightly with temperature. The Bureau also designed a fixed 2-kg weight and associated electromagnetic release, which subsequently were incorporated as standard in a revision of Test 4. The original concept that the test involves only adiabatic compression was found to be an oversimplification; an alternate mechanism for the initiation process is proposed in which due consideration is given to the effects of cavitation and microjets.

Jan 1, 1966

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of ,Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal- mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By Maurice Deul

A special short-term research project was initiated to develop plant design parameters for treating mine waters to yield an effluent acceptable for discharge into streams and a sludge amenable to effective and economic disposal. Neutralization was investigated to provide simple and direct treatment of ferruginous acid waters using lime; coarse limestone, and limestone followed by lime. Limestone treatment was accomplished using a small cement mixer as a simple reactor to provide abrasive agitation of limestone and mine water. Results from tests with nine mine waters encompassing a wide range of iron and acid concentrations showed that coarse limestone, one of the cheapest neutralizing agents known, is potentially useful for treating mine water discharges. However, process variables must be defined more completely before the practical applications and limitations of the process can be fully established. In all the tests a pH of >7.2 was obtained ultimately with limestone. Reaction time to reduce the iron content below 7 ppm in the water was dependent on the original ferrous iron concentration. For waters with high ferrous iron content, treatment with limestone followed by lime rapidly produced an acceptable treated water, Sludges with good settling and handling characteristics resulted when limestone was used for neutralization either alone or with subsequent treatment. Reaction rates are expressed graphically as pH change and iron depletion curves; characteristic solids settling curves are shown. The temperature dependency of ferrous iron oxidation was verified.

Jan 1, 1967

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980