Search Documents

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By W. J. Wiehagen

The Work Crew Performance Model (WCPM) seeks to define performance variability within similar tasks of an underground work crew and relate observed variability to a cost consequence. Performance variability is described using work site observations to determine the adherence to job elements con¬tained within a standard operating procedure. Key components of the WCPM include (1) job definition through task analyses and the ranking of job elements by perceived cost consequence, (2) observational techniques for establishing performance baselines by measuring adherence to safe and proficient job procedures, and (3) cost linkages between adherence to task procedures and measures of consequence for noncompliance. Data presented within this report were obtained through the study of shuttle car operation in an underground mine in Appalachia. Observed adherence to safe and proficient job procedures by opera¬tors matched well with the consensus profiles (measured through a nominal group technique) with min¬ing personnel. It was also found that experienced operators consistently outperformed less experienced, incidental operators. These findings imply potential use of the WCPM as a practical procedure for thinking systematically about the choices available to reduce performance variability. Field application of the model can offer useful data to evaluate training and financially support performance improvement strategies that can be tested for their ability to reduce human error.

Jan 1, 1994

By H. H. Schrenk

One phase of Bureau of lines work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To insure that devices embodying these features will be available the Bureau has established schedules of minimum requirements for oxygen breathing apparatus, gas masks4/, supplied-air respirators (hose mask, air-line respirators, and abrasive blasting helmet hoods, or masks)5/, and dispersoid (dust, fume and mist) respirators6/. Approval test, of oxygen¬-breathing apparatus are conducted by the Safety Division; approval tests of other types of respiratory protective equipment are conducted by the Health Division. These divisions comprise the Health and Safety Branch.

Jan 1, 1941

By Sidney Katell, JOHN H. FABER, BRYCE L. MADDOX

The information abstracted from the various publications appeared in the magazines under such headings as Business and Industry , Chemical Engineering Developments , Companies in the News , Headlines of the Month , Industrial News , Industry , Refining and Gas - Processing News , Refining News , What's Happening , and others . Although most items are related to chemical and petroleum plants , a few pertain to related fields , such as markets , drilling costs for petroleum , and field prices of crude oil . Certain articles discuss various aspects of cost -estimating procedures or description of processes . Cost bibliographies prepared by other groups are discussed in items 70 and 271. The two references can be considered as supplemental to this report , since the amount of overlap in the contents is insignificant .

Jun 15, 1957

By Roy L. Wilfong

The thermal decomposition of the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of praseodymium, neodymium, and samarium was investigated thermogravimetrically in the temperature range 25° to 1,500° C. Each salt was decomposed at a heating rate of 2.5° C, per minute. The pyrolytic sequences have been identified and the temperatures of formation of inter-mediates, the minimum oxide formation temperatures, and values for loss on ignition have been determined. The nonstoichiometric ranges between Pr6011 and Pr203 and the extent of these ranges have been determined for oxides derived from the carbonate, nitrate, and oxalate salts of praseodymium. The alum and sulfate salts of praseodymium produced the sesquioxide without forming the intermediate non-stoichiometric oxides. The temperature limits of formation and regions of stability for the alums and sulfates were better defined than were those for the carbonates, nitrates, and oxalates. The minimum oxide formation temperature increased in the order of samarium, neodymium, and praseodymium irrespective of the anion.

Jan 1, 1962

By D. Harrington

Near the close of the nineteenth century electricity was introduced underground, and the mining industry automatically was confronted with another potential source of fatalities and injuries to mine workers. Electricity has become an increasingly vital factor in the production of goal, particularly in recent years, because of the greatly extended mechanization that has taken place underground. The enlarged use of electrical equipment for cutting, loading, and hauling coal unquestionably increased the potentiality of shock and explosion hazards underground. Electricity may be used in coal mines with minimum danger if electric equipment and power-carrying wires are chosen properly and installed and kept protected by proper safeguards; on the other hand, if vigilance is relaxed in the slightest degree accidents may result. Electrical accidents are caused chiefly by direct contact with electrical equipment or power-carrying wires, by ignition of explosive gas or dust, and by fires of electrical origin. Electricity now ranks fourth as a cause of coal-mine fatalities, not including deaths from explosions or fires of electrical origin.

Jan 1, 1936

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (FM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR), and S) Amplitude Probability Distributions (APD). These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

Jan 1, 1974

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By J. R. Koehler

Effective barrier pillar design is essential for safe and productive underground coal mining. This U.S. Bureau of Mines report presents an overview of available barrier pillar design methodologies that incorporate sound engineering principles while remaining practical for everyday usage. Nomographs and examples are presented to assist in the determination of proper barrier pillar sizing. Additionally, performance evaluation techniques and criteria are included to assist in determining the effectiveness of selected barrier pillar configurations.

Jan 1, 1995

By J. W. Jensen

This report was prepared as a background reference for future publica¬tions concerning the damping capacity of metals and alloys. It contains a broad description of the theory and methods of measuring damping capacity and correlates the developments of the past decade in terminology, units, and techniques. Damping-capacity instrumentation at the Mississippi Valley Experiment Station, Rolla, Mo., is described. The bibliography contains over 150 references to recent articles, each tabulated as to material investigated and test variables, such as frequency, stress, mode of vibration, and temperature. INTRODUCTION After it discovered high-damping manganese-copper alloys before World War II, the Bureau of Mines began research on the damping capacity of alloys and has continued to expand this activity to the present time. In physical metallurgy, damping capacity has become an important research tool in the Bureau. The physical measurement of the damping properties of alloys was begun at the College Park laboratories, and later conducted at Salt Lake City under the direction of Dr. E. V. Potter. Among the many articles resulting from this work, Damping Capacity of Metals (108)3/ has received frequent men¬tion in more recent literature and describes briefly the methods of measurement employed at that time.

Jan 1, 1959

By James M. Link

Underground coal mining is the most hazardous industrial occupation in the United States.. Haulage accidents in underground coal mines contribute substantially to the occupational hazards of this type of work. In an effort to improve mine safety, a completely hydraulic transport system has been designed to move coal from the mine face to the preparation plant. The capital investment for the hydraulic haulage system is great, and the size of the mine developed for this study is large. Mine production for the conventional haulage mine is 1. 1 million tons of clean coal per year, while the hydraulic haulage mine will produce over 1.6 million tons of clean coal per year. Safety statistics for a number of mines of this size are shown.

Jan 1, 1975

By H. F. Yancey

One of the important duties of the Bureau of Mines is to sample and analyze coals and to publish the results of such analyses for the information of producers, consumers, and the general public. Numerous publications containing such analyses have been Issued from time to time. Although the chemical properties of a coal as revealed by its proximate and/or ultimate analysis and heating value aid one considerably in visualizing its probable behavior and in determining its usefulness and value for a specific purpose, they do not furnish complete information. The physical properties of a coal, such as its ability to retain its original form without undue breakage or degradation in size under the various conditions of storage and usage, are also of importance in determining its suitability, technically or economically, for a given purpose.

Jan 1, 1932

Crystalline silica is the scientific name for a group of minerals composed of silicon and oxygen. The term crystalline refers to the fact that the oxygen and silicon atoms are arranged in a three-dimensional repeating pattern. This group of minerals has shaped human history since the beginning of civilization. From the sand used for making glass to the piezoelectric quartz crystals used in advanced communication systems, crystalline silica has been a part of our technological development. Crystalline silica's pervasiveness in our technology is matched only by its abundance in nature. It's found in samples from every geologic era and from every location around the globe. Scientists have known for decades that prolonged and excessive exposure to crystalline silica dust in mining environments can cause silicosis, a noncancerous lung disease. During the 1980's, studies were conducted that suggested that crystalline silica also was a carcinogen. As a result of these findings, crystalline silica has been regulated under the Occupational Safety and Health Administration's (OSHA) Hazard Communication Standard (HCS). Under HCS, OSHA regulated businesses that use materials containing 0.1 or more crystalline silica must follow Federal guidelines concerning hazard communication and worker training. Although the HCS does not require that samples be analyzed for crystalline silica, mineral suppliers or OSHA-regulated businesses may choose to do so if they wish to show that they are exempt from the requirements of HCS. Because crystalline silica is an extremely common mineral and the HCS will affect many mineral commodities, it is important then, that there be as clear an understanding as possible of what is and what is not crystalline silica, and where it is found and used, and how it is qualitatively and quantitatively identified. This primer is an attempt to accomplish this in as nontechnical a manner as possible. This primer will examine crystalline silica. Part I will describe, in nonscientific terms, what crystalline silica is and how we come in contact with it. Part" will discuss the regulatory decisions that have created new interest in this ancient and widespread substance and will present a nontechnical overview of the techniques used to measure crystalline silica. Because this primer is meant to be a starting point for anyone interested in learning more about crystalline silica, a list of selected readings and other resources is included. The detailed glossary, which defines many terms that are beyond the scope of this publication, is designed to help the reader move from this presentation to a more technical one, the inevitable next step.

Jan 1, 1992

By J. C. Fowler

The field testing of the Seismic Mine Monitor System is described. This system consists of nine geophones buried about 40 feet deep over a ten-square-mile area, the amplifiers and electronics needed to get the signals to the mine office, and a central processor unit to detect and locate explosions and large roof falls. Since the problems associated with the original installation were solved, this system has worked for 2 1/2 months. The system has detected roof falls in the pillar areas and has located blasts as small as 114 pound of dynamite. The location accuracy has, in general, been within 250 feet. The system is now being used to gather long-term data on the seismic activity of the mine.

Jan 1, 1974

By Raymond M. Kacmar

This paper describes the Bureau of Mines research program on the reliability of computerized mine-monitoring systems. The basic concepts of computerized monitoring are introduced along with its advantages and limitations. Current Bureau projects covering mine-monitoring systems are described, and some of the major areas of concern that should be addressed by future projects are outlined.

Jan 1, 1982

By F. D. DeVaney

Metallurgists and coal-washing engineers have used heavy liquids for years in studying the characteristics of ores and coal. By such means true separations can be made between the various specific-gravity increments in the materials examined. To use of heavy liquids has permitted determination of the possible grades of tailings and concentrates by specific-gravity methods on any particular size, and therefore the size to which the ore must be crushed to free the valuable material. The simplicity of float-and-sink separation and the high degree of efficiency attained in the laboratory are factors that commend the method for commercial concentrations.

Jan 1, 1940

By D. Harrington

This circular presents part I of a series of papers of a review of the literature on air conditioning in mines, with particular reference to the health, safety, and efficiency of miners. It deals with the physiological aspects of exposure to air contaminated by organic matter, noxious and toxic gases, and dusts that emanate from various sources in underground workings; part II will discuss the relation of abnormal mine temperatures and humidities to the health and efficiency of minors; and part III will describe theoretical and practical methods of air conditioning mines to correct or alleviate the conditions mentioned and will discuss the results attained by some of the systems now in use in various parts or the world.

Jan 1, 1938