Search Documents

By E. D. Gardner

This is one of a series of papers written for the consideration of operators of small gold and silver mines in the West. The paper discusses smelting schedules, general smelting practices that have a bearing on rates, and the reasons for penalties or credits for certain constituents of ores. Crude gold and silver ores generally are shipped to smelters only when milling facilities are not available; however, high tailing losses in milling a high-grade or refractory ore or low smelting rates because of the fluxing value of an are may make direct smelting more economical.

Jan 1, 1936

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By David A. Lipton

In 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources in the Carrizo Gorge Wilderness Study Area (WSA). The 14,571-acre WSA, located 42 miles east of El Centro, CA, is underlain primarily by Mesozoic granitic rocks and pre-Cretaceous metasedimentary rocks. Six prospects were found within the WSA and two mines are adjacent to it. Mineral deposits within the WSA have had insufficient development and rock exposures for calculating resources. The WSA contains no identified mineral resources; however, further exploration may disclose gem quality minerals. Two mines adjacent to the WSA, the Pack Rat and Beebe Hole, have produced gem quality kunzite and aquamarine from pegmatite dikes. According to the owners, a significant amount of gem minerals have been mined here in the last decade. Based on past production and the characteristic minerals indicating gem-bearing pockets, additional pockets are likely. Similar pegmatite dikes occur from Mt. Tule to Carrizo Gorge and may contain gem-bearing pockets. Pegmatite dikes also occur in the WSA near Rockhouse Canyon, but contained few of the mineral associations indicative of gem-bearing pockets. Manganese occurrences north of the Beebe Hole and Packrat Mines and within the WSA contain low concentrations of manganese. Significant sand and gravel were not identified. There is no evidence of deposits of oil and gas, or geothermal energy.

Jan 1, 1985

[ ]

Jan 1, 2011

By J. A. Herdlick

"INTRODUCTION The BeVan quartz crystal prospect in the Indian Creek mining district of Lemhi County, west-central Idaho, was examined by an engineer of the Bureau of Mines 3/ on July 9, 1943. As quartz crystals possessing peizoelectric properties were on the critical list of strategic war minerals, further exploration of the deposit was recommended. The Bureau of Mines exploration began in December 1943 and continued through January 1944. Additional trenching was completed during May and June 1944. This report presents the data obtained by this exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual exploratoiy work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyses samples and makes beneficiation tests.The quartz crystals found during the exploration were examined and classified at the Bureau of Mines College Park, Md., laboratory and checked at the National Bureau of Standards, Washington, D. C.Fred BeVan, of North Fork, Idaho, and Edward F. Cenis, of the Montana Coal & Iron Company, Spoane, Wash., provided much information on the history and past production of the property."

Mar 1, 1948

By T. F. Mitchell

During the investigation or the occurrence of manganese deposits in western United States, Bureau of Mines' examining engineers collected samples from four manganese properties in the Death Valley region, California. These were supplemented by samples submitted by owners of two other properties in the same area. Extensive laboratory tests were made to determine the, amenability of the ores to standard ore-dressing concentration methods. A small sample of high-grade oxide manganese ore from the McWhinney property, San Bernardino County, Calif., was submitted by the owner. Although the sample would sinter directly to plus 48 percent manganese grade, it appeared probable that the ore, if mined in quantity, would be lower in grade and would require beneficiation. Therefore, testing was conducted to remove the chief gangue constituent, calcite. The National Resources, Inc., property (also known as the old Owl Hole mine) is in the Owl Hole Springs district, I mile from Owl Hole Springs, San Bernardino County, Calif., near the southwest corner of Death Valley National Monument. The ore deposits occur as small lenses or ,pockets, evidently .replacements in limestone and granite. Laboratory work was done on a representative sample of orb procured by Bureau engineers.

Jan 1, 1949

By Donald O. Capstick

A mineral survey of the approximately 144,000-acre Borah Peak study area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Forest Service. The area studied included the Borah Peak RARE II roadless areas (No. 14210, 119,864 acres of land recommended for wilderness designation; and No. X4210, 18,440 acres of land recommended as non-wilderness) and other contiguous Forest Service administered land. The study area is in Challis National Forest in southeast Idaho about 30 miles south-southeast of Challis, ID. Burnt Creek, a conterminous study area to the northeast, on lands administered by the U.S. Bureau of Land Managment, was examined concurrently. Dolomite and limestone inferred reserve bases exceed 1 billion tons each within the Borah Peak study area. The material is widespread and of high quality. Extensive sampling and more detailed mapping are required to better define the resources; however, ample dolomite and limestone occur nearby, outside the study area. Dolomite is the main constituent of several geologic formations within the study area. Sample analyses indicate that the more than 1,000-ft-thick Jefferson Formation dolomite is the most pure and is equivalent to material being mined at a dolomite-to-magnesium processing plant near Addy, WA. Analyses from limestone-bearing formations underlying much of the study area indicate that large quantities of the limestone may be suitable for a variety of uses.

Jan 1, 1987

By A. Uiga

The U.S. Bureau of Mines funded a project which addressed objectives concerning irrigation of native plants and inoculation of native plants with vesicular-arbuscular mycorrhizal (VAM) fungi. The specific irrigation objectives were 1) to demonstrate the performance capabilities of solid-set irrigation for reclaimed mineland conditions, and 2) to demonstrate and evaluate three irrigation concepts under two separate water supply conditions. The VAM inoculations were to assess irrigation benefits in establishing VAM relationships for transplanted native species. Following the seasonal demonstration (May to September 1983) at 3 separate mine sites, conclusions were made that apply to the 6 state Western mining industry. The demonstration sites were located in Montana, Wyoming, and New Mexico. Positive conclusions were reached for 1) the use of soil moisture sampling with or without irrigation, and 2) the selection of solid-set sprinklers as the irrigation method. The conclusions about the irrigation concepts and strategy were mixed, due to the short-term (1 season) nature of the project. No conclusions could be reached for the VAM inoculations because the study time was too short.

Jan 1, 1984

By W. R. K. Wu

Studies are reported on the structure of coal and coke with the graphical , statistical densimetric method based on the relation between the molecular volume per carbon atom ( M / C ) and the atomic hydrogen - carbon ratio ( H / C ) . Previous work , mostly from chemical and physical investigations , is critically reviewed . Difficulties in evaluating the ring increment are demonstrated for coal and coke for the statistical densimetric method based on the additivity of atomic volumes of constituent elements . A new diagram is presented for the graphical method . Methods are introduced for correcting M /C and H/C for the presence of minor constituents in coal and coke . With the graphical method , the fractions of aromatic carbon atoms in the total carbon atoms are estimated for a coal , a resin , and 5 petrographic components ; the types of condensed structure in the fundamental units of molecules are discussed for these substances , 28 coals , and 6 " average " cokes at 500 ° to 1,000 ° C. It is also shown that the number of rings in the fundamental units of coal generally increases with increasing rank and that of coke , with increasing carbonization temperature .

Jul 1, 1960

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

1.0 SCOPE AND REGULATIONS 1.1 This specification covers the minimum requirements for material handling and associated equipment including design and materials. 1.2 This specification requires compliance with all federal, state, local laws and regulations which may be applicable including the Occupational Safety and Health Act, Construction Safety Act as well as rules, regulations and standards of the Secretary of Labor.

Jan 1, 1979

By Thys B. Johnson

Operations Research techniques for determining optimal shipping schedules and production and product allocation are discussed. A hypothetical mining operation model is formulated by the Bureau of Mines, and optimal production and product allocation are determined. The technique of sensitivity analysis is discussed and is used to illustrate the effect of the variability in a mining operation on the optimal production and product market plan.

Jan 1, 1969

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts of Mineral County, Nev., made during the month of June and the first 10 days in October 1936.3/ During the field work virtually all the mining districts in the county were visited and many data were obtained relative to active and inactive properties. The report covers the location of the various mining districts, nature of deposits, ownership, information on past and current activity, data on economic conditions, and general information likely to be useful to operators and investors and others interested in mining. The geology of the deposits is discussed only in a general way. For nearly three-quarters of a century mining tin Mineral County has been the principal if not the only industry of importance. At times it has reached a very low ebb, and at other times it has been attended by the wild excitement that usually accompanies valuable discoveries of precious metals.

Jan 1, 1937

By Kenneth Eilerts, Vincent Smith

"INTRODUCTION Knowledge of the Phase relations of fluids produced from combination wells 4/ at the pressures and temperatures characteristic of production from natural reservoirs is essential to efficient recovery and refining practice. An accurate sample of the fluid from such wells may be prepared by mixing (in the proportions of the measured gas:liquid ratio) gas and liquid taken from the separator conditions of steady flow; and physical properties of the sample, at significant pressures and temperatures, may be determined with suitable laboratory apparatus for use in the solution of engineering problems. The results of study of sample so obtained and of mixtures of gas and liquid from the separator combined in other proportions are presented in this report. Attention was given in the study to the relationship between the physical properties of what may be regarded as the constituent materials - the gas and liquid taken from the separator - and the properties of mixtures of these constituents. Data obtained for the complete range of mixture Proportions are expected to provide a reference scale for the study of other combination-well fluids produced at different liquid:gas ratios."

Apr 1, 1942

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By C. P. Mishra

The Bureau of Mines performed a study of the availability of cobalt from market economy countries. The study entailed the detailed analysis of 97 deposits which contain 3.9 billion lb of cobalt at the demonstrated level; in 94 of the deposits cobalt is recovered as a byproduct, and in 3 it is considered the primary product. Since 97 pet of all recoverable cobalt is derived as a byproduct from copper and nickel deposits, the report focused on these two sources. At an assumed market price of $0.89flb for copper, $3.45/lb for nickel, $475/tr 021 for platinum, and $7/lb for cobalt, 1,330 million lb of cobalt at the demonstrated level are potentially available. This total includes 1,105 million lb of cobalt from copper properties, 190 million lb from nickel, 29 million lb from platinum, and 6 million lb from primary cobalt. This analysis indicates that the production cost for 589 million lb of cobalt can be totally covered by the revenues obtained from the other metals produced. The impacts of increases in capital investment and energy costs are also discussed.

Jan 1, 1985

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

By D. J. Dollhopf

The objective of this five year study was to investigate the means of establishing non-polluted ground-water and root zone systems in areas where surface mining intercepts physiochemically unsuitable overburden materials. Overburden may need to be sampled on a 60 m grid in order to delineate materials unsuitable for reclamation and to accurately implement selective handling operations. Unsuitable overburden materials were buried successfully in a dragline operation with a minimum of delays, but costs were increased 12 to 53%. After three years the buried material remains above the reestablished aquifer and below the root zone. Construction of a clay cap over the buried material may not be required in semiarid environments. It was shown that some unsuitable overburden materials do not have to be special handled. When inhibitory material constituted <5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile due to mixing/dilution processes. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. At least a portion of the postmine aquifer had hydraulic conductivity rates lower than the premine system, indicating the reestablished aquifer may, in part, conduct ground water very slowly. Postmine ground-water chemical quality in spoil materials had poorer quality compared to premine ground water.

Jan 1, 1981

The works recorded in this Test Report have been performed by Rade Roncar - Electrotechnical Institute of Zagreb, SFR Yugoslavia in collaboration with Bureau of Mines. The main objective of these investigations was to investigate the possibility of fabrication of thin-walled square enclosures of satisfactory safety factor in accordance with requirements of effective technical regulations. The results and the investigations can be divided in three main fields: - investigations of thin-walled enclosures with the view of determination of pressures causing technological deformations before performing tests in accordance with effective applicable regulations, - finding the safety factor by means of tests of metal-foam pressure vents, - comparison of enclosures with and without pretreatment by technological deformation.

Jan 1, 1987

By Bruce Rock

A continuous mining machine was redesigned for the installation of an integrated illumination system. The illumination system was designed by first calculating the theoretical number of luminaires required to meet the Federal Illumination Standards. Luminaires initially were placed using isointensity diagrams. A darkroom was used for "fine tuning" and demonstrating that the system met the illumination requirements. The luminaire mounts were installed on a machine underground. The performance of this illumination system was monitored in the working environment of an operating coal mine. Design changes were made as necessary during this evaluation period to improve the system.

Jan 1, 1979