Search Documents

By W. H. Oppelt

Two exploratory gasification tests of limited duration were made at Dorsten, Germany, with strongly coking Pittsburgh-bed coal in a fixed-bed pressure gasifier. To reduce the coking potential of the Arkwright coal, ash refuse from the gasification of Dorsten (Leopold) coal was added to pre-pare coal-ash mixtures which contained nominal 20 and 30 percent ash. Major adjustments in principal process variables at the beginning of the tests resulted in wide fluctuations in the rate of gas production, gas offtake temperature, and carbon dioxide concentration in the gas. Because a higher steam-to-oxygen ratio was used in the tests than was customarily employed for routine operation, gas production was lower, and steam and oxygen consumption was higher. After operating conditions had been improved, the results of a 12~-hour-long test with addition of sufficient ash refuse to obtain a nominal 30 percent ash concentration indicated that operation is feasible with this coal mixture using a fixed-bed pressure gasifier equipped with a rotating coal distributor and stirrer.

Jan 1, 1966

By Lito C. Mejia

Diesel-powered equipment operating in a gassy underground mine could conceivably ingest a methane-air mixture from the mine atmosphere that could cause the diesel engine to overspeed, or exceed its rated speed. Engine overspeed, particularly if extreme (engine runaway), could result in personal injury, a possible mine explosion, and/or catastrophic engine failure. In this report, the Bureau of Mines reviews the literature on the potential hazards of methane-induced diesel engine overspeed. Also included are the Bureau's findings from consultations with representatives of the diesel engine industry to determine the specific engine behavior that could he expected under the overspeed condition. The report summarizes data on mine accidents involving methane, discusses results of tests on the compression ignition of methane in diesel engines, and examines fuel governors and intake-air-cutoff devices, two kinds of devices used to prevent overspeed. Analysis of the information gathered suggests that the conditions necessary to cause a diesel engine to overspeed uncontrollably are not likely to occur, particularly if the engine is equipped with flame-proofing devices. The available literature and lack of actual overspeed case histories suggest that the safety devices currently in use are sufficient to prevent diesel engine overspeed.

Jan 1, 1984

By R. J. Fantel

The Bureau of Mines investigated the resource availability of titanium minerals from 63 mines and deposits in 12 market economy countries. These mines and deposits contain, at the demonstrated resource level, an estimated 438 million metric tons (mt) of titanium dioxide (TiO2) in the minerals rutile, ilmenite, leucoxene, and anatase. An additional 314 million mt of TiOz is available from inferred resources. If all titanium minerals and other recovered heavy minerals are sold at total costs at least equal to the January 1984 market prices, approximately 200 million mt of contained TiO2 could be recovered in total. In terms of mineral concentrates, this equals approximately 11 million mt of rutile concentrate, 187 million mt of ilmenite concentrate, 3 million mt of leucoxene concentrate, 13 million mt of synthetic rutile concentrate (in addition to the ilmenite), and 89 million mt of titanium slag. The study indicates that world resources of low-cost rutile are declining. In order to maintain future supply for high-grade titanium resources, alternate sources will need to be developed, which may include higher cost rutile mines, Brazilian anatase deposits, increased production from slag operations, or more synthetic rutile capacity from ilmenite resources, which are abundant.

Jan 1, 1986

By PW Meisel

An hydraulic-powered reel system to minimize peak tension transients in shuttle car trailing cables has been theoretically designed and analyzed using a computer. A single spring-loaded take-up sheave stores or gives up cable to maintain tension within specified limits. Controls have been incorporated to shut down the vehicle before all cable is removed from the reel and to de-energize the cable in the event of a reel/cable jam. Full-scale hardware configuration drawings sufficient for manufacture of a test system have been completed.

Jan 1, 1983

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By J. F. Barkley

The work covered in this report was done to meet the requests from many Government agencies for information on alleviating sludge difficulties in No. 6 (Bunker C) fuel-oil storage tanks. Accumulated sludge at times caused serious loss in tank capacities; pumps became overloaded or lost suction; strainers often required very frequent cleaning; fuel-oil heaters in some instances became fouled and inefficient; and gobs of sludge that passed the strainers interfered with good combustion. The requests also included questions regarding the usefulness in general of oil "additives" for preventing sludge and the relative merits of the many trade-named additives being marketed. Realizing that preventing such difficulties would result in substantial savings to the Government, an investigation was begun with the limited funds avail-able. Although various claims are made for No. 6 fuel-oil additives other than preventing sludge, only an investigation as regards the storage tank-sludge problem has been possible.

Jan 1, 1955

By G. E. Geiger

The purpose of this research was to develop a computer simulator fur predicting the air quality in existing coal mines as well as a design aid for developing new mines. In addition to the air quantity flow, the other variables of tempera Lure, moisture, methane and respirable dust are necessary to determine the air quality. An additional feature of this simulator is that it allows parametric studies of these variables to explore the effect that these variables have on the air quality of an operating mine system. The research has also pointed out arias where more research is needed, and promote better and more systematic data taking techniques. Wang and Hartman (see Reference 9, on page 1-98 of Section 1) had already published a computer program to determine the ventilation of large mines, and Wang and Saperstein (see Reference 10 on page 1-98 of Section 1) later published a refinement of the work in the previous reference. These references were the starting point of the simulator developed by this present research effort, and Section 1 of this report is a slightly modified version of the original vent elation program. The modifications were necessary to permit the additional programs of temperature-moisture, methane and dust to be

Jan 1, 1972

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

By H. H. Fields

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot-deep vertical borehole¬. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmos¬phere, the total gas and water flows and the in situ pressure dropped, respec¬tively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the correspond¬ing values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By Max L. Glenn

As part of its goal to minimize requirements for mineral commodities through conservation and substitution, the Bureau of Mines conducted research to develop molybdenum as a potential substitute for superalloys containing the strategic and critical materials, nickel, chromium, and cobalt. Since molybdenum requires protection from oxidation at high temperatures, several complex oxides of the spinel and perovskite structure were investigated to determine which possessed the greatest potential for use as oxidation-barrier coatings. Two spinels (MgCr204 and MgA1204) and five perovskites (BaHfO3, YCrO3, NdCrO3, BaZrO3, and LaCrO3) were selected for testing. Various high-temperature prop¬erties that are important for oxidation-resistant coatings were examined, including diffusion rates of oxygen and molybdenum, recession (vaporization) rates, hardness, erosion resistance, sinterability, reactivity with molybdenum, and ease of application. From the evaluation of high-temperature properties, two spinels (MgCr204 and MgA1204) stand above the other oxides as possible coatings for molybdenum. However, laboratory coatings of MgCr204 at 1,360° C (2,480° F) are equivalent or inferior to currently available MoSi2 coatings; laboratory coatings of MgA1204 may be comparable under limited conditions to currently available MoSi2 coatings at the same temperature.

Jan 1, 1979

By James R. Boyle

The Bureau of Mines initiated a program to address short-and long-term objectives of wetlands restoration as a option for reclamation of lands mined for phosphate. The short-term objectives were to identify a suitable wetland test site, initiate an extensive premining monitoring plan, develop an acceptable mining plan, and recontour and revegetate the test site. These goals were accomplished using a unique combination of expertise provided by Federal and State agencies and private industry. A 6.5-ha forested wetland with an associated streambed was offered by private industry as the test site. A premining monitoring program was established and carried out from May 1982 to October 1983. A control site was established to determine ecological changes unrelated to mining. Clearing and mining began in October 1983 and was completed in April 1984. Grading and streambed restoration was completed in February 1986. Revegetation of the site was completed in February 1987. The program to meet the long-term objective of postmining monitoring is described.

Jan 1, 1988

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974

By K. Zipf, Z. T. Bieniawski

"An extensive mixed-mode fracture toughness testing programme was conducted on coal from three coal fields. A special mixed-mode testing fixture for coal and other geologic materials was developed together with reliable specimen preparation procedures. Dynamic modulus measurements made on each of the 116 fracture toughness specimens showed that these coals exhibit certain degrees of anisotropy. The fracture toughness testing programme systematically varied the loading rate, specimen orientation and fracture loading mode. Loading rate did not significantly effect the fracture toughness over the quasi-static range tested. Orientation did have a significant effect on measured fracture toughness. In the coals tested, the divider orientation and arrester orientation had higher fracture toughness than the short transverse orientation. Data showed that one orientation could have almost twice the fracture toughness as another. The fracture toughness testing enabled certain evaluations of three mixed-mode fracture theories: maximum tangential stress, maximum energy release rate and strain energy density theory. Due to the extreme heterogeneity of the coals tested, definitive conclusions regarding the best mixed-mode fracture theory are not possible; however, data do tend to support the strain energy density theory. INTRODUCTIONThe major aim of this research is to ·develop a fundamental understanding of how fine· fragments of coal (respirable dust) are generated during a fracture process. In a related paper [l], a hypothesis was presented for the mechanism of fine fragment formation during a generic coal material/cutting tool interaction. In this hypothesis, fine fragments are created during coal material/cutting tool interactions that are best described as general mixed-mode fracture processes. Data are required on the mixed-mode fracture behaviour of coal, the physical character of the newly-created fracture surfaces and the character of the inherent flaw structure of the coal material. Accordingly, a test programme was designed that provided some information in each of these areas. The testing effort seeks to measure critical fracture toughness under mixed-mode loadings as a material parameter characterizing in part the tendency of various coals to generate undesirable quantities of fines and respirable dust."

Jan 1, 1990

By J. B. Czirr

MESA Corporation has completed a four-year program for the Bureau of Mines to develop a technique for measuring roof competence in underground coal mines. The preferred technique employs a tracer gas that is injected into a roof borehole drilled near the working face. The tracer gas performs the dual purpose of determining the pressure loss rate from the borehole and of marking the diffusion pattern of the the escaping gas. The primary detection technique relies upon observation of the rate of pressure drop in a hole drilled in the roof strata under test. If this measurement indicates a significant probability of roof collapse, the gas diffusion pattern is outlined with the Leak-gun tracer-gas detector. These two techniques provide a comprehensive method for predicting the relative probability of roof collapse in operating coal mines.

Jan 1, 1985

By Thomas Jenning, C. M. Keithly

"INTRODUCTION This report is one of a series. 4. 5. 6/ concerned with presenting historical development, and operating data on secondary-recovery projects in various States to stimulate interest in sound secondary-recovery programs. Preceding reports in this series have dealt exclusively with descriptions of and results obtained by water flooding in three states, but no recent publication of comparable purpose describes gas-injection 7/ practices. The authors intend to present material relevant to the development and operation of gas-injection projects in Illinois, with particular emphasis on those producing from oil-bearing horizons that had been depleted to a point near the economic limit of operation by past oil-recovery methods.Most operators realize that the energy expended on the movement of fluids through gas-expansion- or gas-cap-type oil reservoirs to producing wells must be supplemented to attain maximum recovery of the oil present. Under favorable conditions, many operators choose to maintain oil-propulsive forces at or near their original magnitude by injecting extraneous fluids into a reservoir or recycling produced fluids early in the life of a field. More common, and less desirable, is the practice of replenishing these forces after primary producing methods become unprofitable. The lattes practice has been adopted in many stripper fields in Illinois and most of the oil-producing States during the last 40 years, but other old oil fields, and oil properties within those fields which were partly exploited by secondary--recovery methods, also may offer favorable opportunity for further development. To encourage and, aid operators in the development of gas-injection projects in the old oil fields of the United States, four projects have been described in detail in this report."

Nov 1, 1944

By Welby G. Courtney

This publication reviews recent U.S. Bureau of Mines studies of frictional ignition of a methane-air environment by coal mining bits cutting into sandstone and the effectiveness of remedial techniques to reduce the likelihood of frictional ignition. Frictional ignition with a mining bit always involves a worn bit having a wear flat on the tip of the bit. The worn bit forms hot spots on the surface of the sandstone because of frictional abrasion. The hot spots then can ignite the methane-air environment. A small wear flat forms a small hot spot, which does not give ignition, while a large wear flat forms a large hot spot, which gives ignition. The likelihood of frictional ignition can be somewhat reduced by using a mushroom-shaped tungsten-carbide bit tip on the mining bit and by increasing the bit clearance angle; it can be significantly reduced by using a water spray nozzle in back of each bit, which is carefully oriented to direct the water spray onto the sandstone surface directly behind the bit and thereby cool the hot spots formed by the worn bit. A bit replacement schedule must be used to avoid the formation of a dangerously worn bit.

Jan 1, 1990

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By Normal Seidle

This report (rind related Appendices) provides a description of the functional design specifications and related rationale for development of a training system for dragline equipment operators. Phase I activities involved a delineation and detailed analysis of specific behavioral requirements for successful dragline operation. Following the field data collection effort, job/activity/task descriptions were formulated into training requirements which can be achieved by a trainee with training hardware having specific functional capabilities. The training system analysis integrated the training requirements and the trainer functional capabilities into recommendations which configure a total training system. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1975

By Michael A. Staiano

The objective of this study was to determine the magnitude and sources of environmental noise from mining operations near populated areas, to de-scribe monitoring techniques, and to identify applicable existing noise abatement techniques. To this end, noise surveys of a representative sample of mines and quarries were conducted. Noise levels at site boundaries and near specific equipment and ensembles of equipment were measured. Noise exposures in terms of annual day-night sound level were calculated for the boundary noise measurement locations. In addition, the relative sound level contributions were estimated for the mining equipment noise sources affecting the boundary locations. Noise abatement methods falling into three categories were analyzed: equipment practices, operational/administrative practices, and equipment quieting. Selected applications of noise abatement methods were evaluated in hypothetical situations with emphasis upon machinery selection and use. Procedures for measuring noise around mining operations were provided.

Jan 1, 1981