Search Documents

By F. D. DeVaney

The supply of manganese is a subject of much interest. The idea of obtaining it from rhodochrosite-MnC03 is attractive because the carbonate is supposed not to be so contaminated with impurities as the commonly utilized oxides. Large bodies of rhodochrosite-bearing rock have been known for a long while to exist at Butte, Mont. Hence samples were obtained from that place. In the two samples examined quartz was the chief diluting substance. The leaner sample was about one half quartz; some copper, lead, zinc, and iron sulphides were also present. The rhodochrosite amounted to about 40 per cent, so that the sample had a tenor of about 20 per cent manganese. This sample was the subject of the examination reported herein.

Jan 1, 1928

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By Murray Jacobson

A method for determining airborne trona dust concentrations using a midget impinger was developed. During sampling, the trona dust, composed of sodium carbonate and bicarbonate, dissolves in the collecting medium (water). Resulting solutions are then titrated using 0.1 [N] hydrochloric acid solution. The mass concentration of the trona sample is determined from a calibration curve relating the volume of acid required for neutralizing a collected sample to the mass of the dust. Test results obtained using this method are equivalent to those obtained using a gravimetric sampling method.

Jan 1, 1971

By Paul C. Hyndman

No minerals have been produced from the McGraw Creek RARE II area. During the 1982 U.S. Bureau of Mines study, there were no active mines in the area. Limestone occurrences (fig. 1, no. 2), four copper prospects (fig. 1, no. 1, 4, 5, 6), and a prospect with no significant mineral values (fig. 1, no. 3) were examined. A moderate potential for high-calcium limestone resources was estimated between ocurrences within the study area near McGraw and Spring Creeks (fig. 1, no. 2). There is low potential for copper resources at the Argenta Prospect (fig. 1., no. 1) in the study area, and the McDougall Prospect adjacent to the area.

Jan 1, 1983

By Dana C. Reinke

Jan 1, 2005

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960

By Z. Zborovszky

The feasibility of using the nucleation properties of combustion generated particulates for the identification of their sources was investigated, using the Cloud Condensation Nuclei (CCN) Spectrometer. The Investigated materials included coal, wood, belt materials, electrical insulation, brattice cloth, and diesel exhaust. The materials were heated In an oven using filtered air flow, and their time, temperature, and the critical supersaturation spectrum of condensation nuclei (also referred to as the CCN spectrum) produced by the combusting material were recorded. Some data was obtained on a typical metal-mine background containing blasting products. The data was processed and analyzed In an attempt to specify parameters and limits that would allow the identification of the combustion sources. It appears that under controlled test conditions It Is possible to Identify the source on the basis of data derived from the CCN spectrum. More general use of the Idea for fire detection under uncontrolled practical circumstances in an actual mining environment does have potential but would require further research.

Jan 1, 1978

By Forrest T. Moyer

INJURY experience and employment data are presented in this chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume II. The 1962 figures are preliminary summations which are subject to revision. They were compiled from all reports from producers received by the Bureau of Mines through April 15, 1963. The data for metal, nonmetal (except well and brine operations), stone, and sand and gravel operations were collected by a mandatory reporting system under the provisions of the act of September 26, 1961, Public Law 87-300 (75 Stat. 649). The act authorized the Secretary of the Interior to study the various aspects of safety in metal and nonmetal mines (excluding coal mines) and report the findings 2 years sub-sequent to the enactment of the law. Data on nonmetal well and brine plants and nonferrous reduction plants and refineries were reported voluntarily by the operators. METAL MINES Preliminary data for the metal mining industry comprise reports on 1,871 mines and pits. The combined fatal and nonfatal injury-frequency rate was 31.95 per million manhours in 1962, a decrease of 8 percent from the similar rate of 34.54 in 1961. Metal operations reported a total of 61 fatal and 3,201 nonfatal injuries.

Jan 1, 1963

By Matthew N. Plis

This U.S. Bureau of Mines report presents the documentation for COALVAL, a coal property evaluation software package developed on Lotus 1-2-3,4 version 2.2, spreadsheets. The software is compatible with version 3.1 as well, and may provisionally be run on the earlier 2.01 version. COALVAL is a menu-driven program that produces a prefeasibility-level cost analysis of mine-planned coal resources. The package contains cost models for each of five coal mining methods commonly employed in Appalachia: auger, contour strip, mountain top removal, continuous miner, and longwall. Other models, such as a dragline cost model, will be incorporated as the Bureau's Coal Recoverability Program matures. COALVAL allows mine operators, evaluators, consultants, and Government entities to input resource data and the various production, operating, and cost variables that pertain to their property. The program can evaluate up to 25 seams, each to be mined with up to five different mining methods, within a given area. Summary spreadsheets listing the cost per clean ton to mine the resources, f.o.b. the tipple, are produced for each property, seam, and mining method/seam combination.

Jan 1, 1993

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By J. A. Woolf, E. S. Leaver, A. P. Towne

"INTRODUCTION A report giving experiments dealing with factors affecting the floatation of the most commonly occurring silver minerals was published years ago. At that time we could not obtain suitable samples of many of the so-called sulfo-salts of the base metals, which are generally silver--bearing and which comprise an appreciable percentage of the natural silver ores. Since Leaver and Woolf's work was published, samples of impure tennantite and enargite have been obtained, and considerable experimental flotation work has been done with synthetic mixtures prepared from these samples. During the present national emergency, research dealing solely with the recovery of gold and silver must necessarily be curtailed. However, many deposits of strategic minerals and critical base metals contain an appreciable amount of gold and silver, the recovery of which would aid greatly in recovering the strategies by taking care of a considerable part of the cost of treatment. Because of this, the recovery of precious metals should not be overlooked entirely. As the Bureau of Mines is now utilizing all of its facilities for the development of increased domestic productions of strategic and critical minerals, this is the last report not concerned primarily with such minerals that will be published until the war ends."

Sep 1, 1942

By C. C. Furnas

In the course of an investigation3 of the flow of gases through beds of broken solids the author obtained a number of data .on the specific volume of beds of broken solids of variously mixed sizes. A mathematical theory of the limiting conditions has been developed and some generalizations have been made for intermediate cases. A more definite knowledge of the relation between space occupied and size composition would be valuable to all those who are handling large quantities of broken materials. Such knowledge might be advantageously applied to the operation of a coke oven. For example, the output of the oven depends in general upon the number of pounds of coal which can be put in the oven at charging. It is known that the capacity of one battery of ovens was increased several per cent by slightly increasing the proportion of fine material in the charge.

Jan 1, 1928

By H. H. Schrenk, Carlton E. Brown

"The purpose of this paper are (1) to present a broad picture of the recognized methods of measuring the various forms of atmospheric pollution; (2) to evaluate the significance of such measurements; and (3) to suggest suitable methods for obtaining comparative information on the concentration of contaminants in city air.The atmosphere (the gaseous envelope surrounding the earth) consists of a mixture of gases. These gases and their usual proportions are:4/The volume of water vapor in the atmosphere ranges from almost zero (in very cold weather) to about 5 percent arid averages about 1.2 percent.Strictly speaking, any other substance in the atmosphere or an excess of any of the substances mentioned (with the possible exception of water) is a contaminant. Needless to say, there are many contaminants in the atmosphere.In accordance with their physical state, contaminants may be classified as gaseous or particulate, and the latter may be classified as solid or liquid matter. Particulate matter, especially when dispersed in some medium such as air or some other gas, sometimes is referred to as dispersoid, and the complete system of gas and dispersoid is referred to as aerosol.All substances on the earth are potential sources of atmospheric contaminants. Combustible materials (particularly fuel for heating and power), sea water, earth or soil, metals, and animals (including man) are some of the important sources of contaminants.Ordinarily gases are produced by chemical processes, whereas dispersoids are produced by both chemical and physical processes. There are two general dispersoid-producing processes: (1) Condensation, in which molecules join to form larger units or particles, and (2) disintegration, in which large units are reduced to the particulate range (which for the purpose of this article may be considered to be from 100 microns, or 1/254 inch, down to molecular size) by such processes as crushing, grinding, abrading, and atomizing.“Condensoid"" is a convenient term for dispersoids formed by condensation, and ""disintegrasoid"" for those formed by disintegration. Solid condensoids are sometimes called ""fume,"" solid disintegrasoids ""dust,"" liquid condensoids ""fog,"" and liquid disintegrasoids ""mist.""5/"

May 1, 1942

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By Donald F. Reed

The bauxite deposits of Tippah and Benton Counties in northeastern Mississippi were developed by drilling as a part of the investigation by the Bureau of Mines of the domestic sources of supply of aluminum. The primary purpose of investigations of this nature was to provide essential information to the war agencies of the United States Government and to assist owners and operators of mining properties in the production of minerals vital to the prosecution of the war. These reports are based upon the field work of the Bureau of Mines and upon data made available to the Department from other

Jan 1, 1948

By R. A. Welsh

The Bureau of Mines has developed a photoelectric concentrator apparatus which is capable of collecting incremental products from the discharge of wet concentrating tables. The instrument uses photoelectric cells as sensors to differentiate between two products which have differences in color or reflectivity. The photocells provide a signal that controls a mobile splitting device that separates the products. Tests conducted on a wet table demonstrated the ability of the apparatus to separate a product containing 81.5 percent pyrite from a lower-grade product containing only 68.8 percent pyrite. The photoelectric concentrator should have a broad application for collecting concentrates with visible color or reflectivity differences from wet concentrating tables.

Jan 1, 1972

By Marshal Scherba

Coal seams approximately 7 feet, 9 feet and 20 feet thick at depths of 250, 600 and 1,000 feet respectively were detected using high resolution seismic reflection techniques. Investigation of seismic profiles indicates that good data are required to delineate faulting with only 20 feet of throw but that faulting with 50 feet of vertical displacement can be detected with poor data. Data acquired from dynamite charges fired in water saturated media were clearly superior to that acquired using charges dry tamped in 10 and 20 foot holes.

Jan 1, 1977