Search Documents

By F. K. McIntosh, A. F. Robertson, T. J. Ballard

"INTRODUCTION Molybdenum deposits occur in Halifax County, N. C., near the eastern border of the Piedmont province. The deposits are associated with a small granite body about 2 miles long and half a mile wide. Molybdenite is the principal ore mineral and is found as disseminations or thin stringers in quartz veins and occasionally in the enclosing granite or schist wall rock.The deposits were investigated by Almon F. Robertson and Charles J. Cohen, engineers of the Bureau of Mines, in 1942 and 1943, who recommended that the deposits be explored to supplement reserves of critical war minerals.The Bureau made the initial exploration of the deposits in July 1943 and continued its work to January 1944. Drilling was resumed from July to December 1946 to test the deposits at &eater depth than had been attempted during the previous exploration."

Dec 1, 1947

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By Richard W. Lewis, Lloyd Carpenter

The objective of the investigation was to determine spectrochemically 19 elements in the general range of 0.5 to 1,000 ppm in high - purity hafnium and its compounds . Samples were converted thermally to hafnium dioxide , mixed with buffer - carrier - internal standards , and excited by a dc arc . Spectra were recorded on photographic plates . Transmittance values were recorded densitometrically and converted to relative - intensity ratios . Four groups of standards were used to establish analytical curves from which the concentrations of impurities were obtained . Average precision of the method was 14.2 percent relative standard deviation , and relative error was 4.2 percent .

Jan 1, 1964

By Robert C. Steckley

A study of joints in Marathon County, Wis., was made to determine the orientation of regional paleotectonic stresses and to develop a method of using optical diffraction analysis (ODA) in studying joint orientations and spacings. Standard geologic and petrofabric techniques employing the use of a geologic compass and a Schmidt net were used in gathering, describing, and reducing joint orientation data. Analysis of selected outcrops with ODA indicates that ODA can be applied to study both joint orientations and spacings. ODA is shown to be a rapid method that can be used to complement standard petrofabric techniques, especially in the study of joint spacings.

Jan 1, 1972

By C. E. Munroe

In order to meet the emergencies of the world wr, tne quantities of explosivea produced in the Unitecl States, and the number of explosives plants were onti:.1.1.:l,lly ncreased so that when the armistice was declared the Government had on hand larg ..mounts oi militazy explosives in excess of existing military needs. Tle stor3.gs of these explosives entailed a liirge expense and their protection neessitatei the employment of m'3.l'lY men who could be better employed otherwise in the military estlish.11ent. Moreover, mar.y ex.ploives, like QJ.l other material, deteriorate on prolonged storage, They lose tht precise definiteness of properties and behavior on which reliance· is placed in military operations, The continued expen3e and d3.nger ttending storage of theae explosives might be diminished by dcst1et1on of the surplus beyond immediate needs, but such·deetniction is danger• ou5 qnd coetly. Hence, the evident solution o! the problem was the salvage d prompt ut111zation of the ru.rplua •

Aug 1, 1922

By William D. Monaghan

The U.S. Bureau of Mines evaluated a teleoperated continuous mining machine for deep mining in thin-seam applications as low as 1 m. Teleoperation increases the safety of mining machine operators because it removes the operator from the face, an area of immediate hazards to safer outby locations. By using teleoperation, the miner can avoid many including unexpected roof falls that can maim or kill miners instantly, methane and coal dust explosions that can be ignited with just a small spark or flame, adverse health effects from miners breathing coal and silica dust, adverse long-term inner ear damage from loud noise pollution, and other hazards related to heavy mining equipment moving about in confined underground roadways. This report presents the surface evaluation results of a teleoperated control system.

Jan 1, 1994

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

Case 1: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ] Case 2: A crew was preparing to remove a pump from a well when the hoist boom contacted a 4160-volt power line. The hoist operator was electrocuted. [ ]

Jan 1, 2005

By Benjamin W. Haynes

The Bureau of Mines, in cooperation with the National Oceanic and Atmospheric Administration (NOAA), has updated a 1977 NOAA report prepared by Dames & Moore entitled, "Description of Manganese Nodule Processing Activities for Environmental Studies." This updated report contains detailed flowsheets and descriptions of the five potential first-generation nodule recovery schemes now considered most likely to be used by industry; they are high-temperature gas reduction and ammoniacal leach, Cuprion ammoniacal leach, high-temperature and high-pressure H2S04 leach, reduction and HCI leach, and smelting and H2S04 leach. The first three processes are three-metal recovery schemes (Cu, Ni, and Co) with the option of Mn recovery from the tailings. The remaining two processes are four-metal (Cu, Ni, Co, and Mn) recovery schemes. All except the HCI process are assumed to use a nodule feed rate of 3 million tons per year (dry basis). Final metal products are Co powder and cathode Cu and Ni. A minor amount of Ni is also recovered as powder, and some Cu and Zn are recovered as mixed sulfides. Manganese in the four-metal processes is recovered as either manganese metal or ferromanganese.

Jan 1, 1983

By James D. Brown

The Bureau of Mines has written a computer program in FORTRAN to facilitate the calculation of concentrations from X-ray intensities in electron probe microanalysis. Philibert's absorption and Castaing's secondary fluorescence corrections are used; no atomic number correction is included. Background and dead time corrections are applied to the data before calculating the relative intensities. Data from any type of electron probe microanalyzer can be used with the program.

Jan 1, 1965

By D. A. Paice

Direct current electrical systems are used in most coal mines primarily to power the main haulage trains and secondarily to feed other equipment and passageway lighting. Electrical power is supplied from rotary machines or static rectifier equipment and is distributed through the mine by open trolley wires and feeder cables. The rails of the haulageway are used as a current return path. This exposed power distribution system is very vulnerable to conditions which lead to undesired leakage currents and short circuits and, consequently, the possibility of fires or other hazards to personnel. Present techniques and equipment have been utilized in so far as practical to improve the safety of the dc electrical system; however, there still appears a need for further improvement. Because of this need, this program was sponsored by the Bureau of Mines to investigate two specific technical areas related to improvement of dc electrical system safety. One area included the determination of the characteristics of mine electrical systems and their protection requirements and the verification of the adequacy of available protective devices for mine service. Despite the widespread application of industrial protective equipment in mines, there was little detailed technical information available related specifically to the performance of this equipment in service. Our task was not only to develop useful information regarding mine system protection, but also to define and verify the adequacy of the protective devices available. The second area of investigation called for development of a practical technique for detecting low level electrical fault or leakage currents. Conventional protective devices

Jan 1, 2012

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By Harry R. Nicholls

Preliminary tests on presplitting rock in the presence of an in situ static stress field were undertaken to study the influence of a horizontal static stress field on the creation of a vertical presplit fracture plane. These tests indicated that it is easier to fracture the rock parallel to the in situ maximum compressive stress than in other directions. Instrumented shots indicate that the interaction of stress waves generated by the detonating charges is probably responsible for starting tensile fractures between shotholes and that expanding gases may propagate these initial cracks by a wedging action. The hole spacing for presplitting appears to be equal to the half wavelength of the stress wave. However, wider hole spacing appears feasible if the initial fracture is started by closer hole spacing.

Jan 1, 1966

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.5

Jan 1, 1963

By Edward M. Kawenski

Float dust deposits in return airways in bituminous coal and lignite mines present a special explosion hazard. Research is in progress at the Bureau of Mines experimental coal mine to evaluate the degree of the hazard and to develop measures for preventing dissemination of dust into the ventilating air current. To determine the extent of this hazard prevailing in operating coal mines, 711 dust samples were collected in 50 mines located in the major coal fields of the United States. The mean quantity of coal and the incombustible content of the dust in the samples were determined. The term "float dust" is used to designate particles smaller than 74 microns in diameter (particles passing a No. 200 sieve) which have settled from the air current. Dust usually found in roadways and in working places is coarser than float dust, and is termed "coarse dust" (particles passing a No. 20 sieve). Variations in amount and incombustible content of coarse dust in a midwestern mine were studied previously.

Jan 1, 1963

By B. Gillenwater

This report describes the results of investigations into four specific areas related to trolley wire power distribution systems in coal mines. These are: 1. Partially insulated (shielded) trolley wire 2. High-speed insulator fault detectors 3. Dual-wire trolley systems 4. Insulator failure indicators. Prototype devices or designs were developed in each area. In addition, a brief survey was made in an attempt to assess the Future of mine trolley systems, and data was collected and reviewed in an attempt to analyze the nature of trolley wire related accidents. Other options for decreasing the risks associated with trolley systems that arose .during the study are briefly described in appendices. These include insulating equipment and miners from return and/or energized conductors and use of a segmented trolley wire with local control of current delivering capability.

Jan 1, 1981

By J. A. Kost

The objective of Contract J0295041 was to determine if the addition of a surfactant (wetting agent) to the water used for dust control in underground coal mines results in the reduction of airborne dust. Laboratory wettability tests, including the capillary rise test, a coal dust sinking test and zeta potential measurements, were used to select a coal seam/surfactant combination for in-mine testing. Four surfactants were selected for underground testing: Surfynol 465, Aerosol MA-80, DC-13, and Dustallay. The underground tests in the Lower Kittanning seam, Indiana County, PA, involved a Wilcox Mark 20 auger mining system, equipped with spray nozzles located on the cutting augers, Conflow venturi sprays, and a spray manifold. Respirable dust samples were provided by MSA Model G personal samplers and Simslin II instantaneous dust monitor; total airborne dust samples were provided by MSA Model G samplers with UNICO filter cassettes. Based on data obtained from 24 test periods surfactants, as compared to plain water, reduced the airborne respirable dust an average of 27 percent and total airborne dust an average of 36 percent.

Jan 1, 1980

Collins Radio Company, through this contract with the Bureau of Mines, has conducted a System Study of Coal Mine Communi¬cations. The program was a three phase program to establish a data base, perform communication system analysis and optimi¬zation, and prepare equipment specifications to be included in this final report. At the start of establishing a data base both a knowledge of mine communication and coal mines in general was obtained. Communication system requirements and constraints were determined along with a survey of current and potential mine communication equipment. An investigation was completed concerning theoretical LF and VLF propagation characteristics, and UHF propagation tests were conducted in a working coal mine. Different mines were contacted and on-site surveys completed with respect to coal mine communication requirements.

Jan 1, 1973