Search Documents

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By L. J. Froisland

The U.S. Bureau of Reclamation requested U.S. Bureau of Mines (USBM) assistance in developing design data for moving lead-zinc-gold tailings from their current location without disrupting the existing chemically stable conditions. This report presents results of USBM work in determining (1) the minimum required time to air dry the tailings to approximately 20 pet moisture under various drying conditions both in the laboratory and in the field, (2) the degree of oxidation or reduction that occurs during drying, (3) the effect of lime or cement addition before drying, and (4) the likely equilibrium conditions of the dried tailings after deposition at the new location. The limited number of tests performed by the USBM in the available time frame established trends in oxidation levels but did not provide absolute statistical validity of data values. All data from drying and oxidation testing are included in appendices to this report.

Jan 1, 2010

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

By James H. Rowland

The Mine Improvement and New Emergency Response Act of 2006 (MINER ACT) established a Technical Study Panel (The Panel) to provide recommendations on the utilization of belt air and new technology that may be available for increasing the fire resistance properties of conveyor belt used in underground coal mines. The Panel Report recommended use of the Belt Evaluation Laboratory Test (BELT) as the method for testing and approval of flame resistant conveyor belts used in underground coal mines. The research conducted to establish the correlation of the BELT with large-scale belt fire flammability tests was done using 36- to 42-in wide conveyor belt. Due to today?s coal haulage capacity, the mining industry is using 72-in and wider conveyor belts. The National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine if the BELT will also qualify wider belts as fire resistant for use in underground coal mines. This paper describes the results of recent experiments comparing results from using the BELT and the large-scale tests for six different belts.

Jan 1, 2010

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By Terry R. Neumann

During 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized zones to evaluate the mineral resources and potential of the Funeral Mountains Wilderness Study Area (WSA), Inyo County, California. Eleven mineral properties and two mineralized zones were examined during this study. Of these, six are within the study area and seven adjacent. There are no active mines, in the WSA, nor is there evidence of past production from any claim within the study area. The WSA contains no identified mineral resources. However, occurrences of bentonite, zeolites, and strontium were found in the area. There is little likelihood for resource development of any occurrence in the WSA. The area, in the Basin and Range Physiographic Province, is dominated by a Paleozoic marine sequence. Segments of Tertiary continental fluviolacustrine sediments, including volcaniclastic rocks, abut and overlie the Paleozoic rocks in fault controlled basin areas. Significant concentrations of bentonitic clay and zeolites occur as alteration products in Tertiary tuffaceous sedimentary rocks. However, they are generally low-grade, thin, and discontinuous, precluding commercial development. Limestone, quartzite, and sand and gravel in the area are suitable for many types of construction uses, but similar deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By Glenn Adkins

This report characterizes pivoting joints in the structures of mining machinery and how the wear on the various components, i.e., pins, lugs, yokes and bushings, may affect the safety of mine personnel where these components are allowed to wear excessively before repair or replacement.

Jan 1, 1979

By E. P. Barret

Differences in the reducibility of iron oxide materials have been recognized for a long time. Limonites are deoxidized more readily than hematites, and unaltered magnetites are the most difficult to deoxidize. Sinters are found between hematites and magnetites and vary considerably in reducibility, depending on the sintering practice followed and on the degree of fusion of the product. The increased activity in the beneficiation of taconite recently has made available a new blast-furnace raw material, namely, iron oxide pellets made from magnetic taconite concentrate. Many of the data in this paper apply to these pellets, or glomerules, as they were called when this method of agglomerating iron ores was first considered. To clarify the terms applied to iron oxide materials in this paper, the following definitions are given. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron oxide materials. Sinter is the product from a Dwight-Lloyd or Greenawalt sintering machine. Pellets are formed by balling fine, moist oxide in a rotating drum at room temperature, followed by heating in a shaft furnace to a temperature below that of incipient fusion to develop a permanent bond. Nodules are formed by heating the iron oxide material to incipient fusion in a rotary kiln. Briquets are formed in a mold under pressure, with or without the addition of a binder, and burned to develop a permanent bond.

Jan 1, 1949

By Robert Stefanko

Test procedures for evaluating underground coal mine trailing cable splices are formulated. The tests are utilized to evaluate several trailing cable splices. The laboratory results are compared with actual field observations and experience. The results are utilized to define quantitatively the generalized terms of the 1969 Health and Safety Act. Recommended specifications and procedures for testing by MESA Department of Approval and Testing personnel are included. Failure points in splices are detailed and presented for use by a MESA training program and manufacturers attempting to improve product quality.

Jan 1, 1974

By Michael Rieber

Among the principal gathering/distribution systems for coal is over-the-road trucking. Where alternative trunk line modes such as barge or rail links are weak or nonexistent, trucks may, particularly for relatively short line hauls, act as substitutes. Their major application, however, appears to be in connection with smaller mines or coal users particularly where terrain problems are significant. Truck use has increased as rail lines have been abandoned or suffered neglect. For example, in 1956 about 38 percent of the coal transported in eastern Kentucky and about 8 percent of the coal moved in western Kentucky went by truck. By 1975, the percentages were almost 77 percent and 26 percent, respectively [4,U-11]. While rail route .limitations and deterioration played a part in the change, increased emphasis on road building, particularly during the 1950's and 1960's, and improved truck load capacity and efficiency were also important.

Jan 1, 1977

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By R. D. Eash

The purpose of this research contract was to develop and test a Saran latex modified portland cement concrete lagging to be used as a replacement for wood lagging. The scope of work performed was divided into four phases: Phase I - Engineering Criteria; Phase-! I1 - Design Study; Phase III - Fabrication of Lagging; and Phase IV - Prototype Demonstration Project. Each phase of work was completed and is described in detail in this report. The prototype latex modified concrete lagging developed in this program weighed 52 pounds. When tested in flexure, it supported center point loading of 4500 pounds and under 1/4 point loading it supported loadings of 7000 pounds. Deflections at maximum loading ranged from 1/2 to 1 inch. Maximum deflections exceed 2 inches. The lagging does not exhibit catastrophic failure. Two hundred and twenty of the LMC lagging were produced and shipped to the Bunker Hill Company in Kellogg, Idaho for installation in their mine at the 17 level. The lagging are performing satisfactory after 22 months exposure in the mine.

Jan 1, 1980

By Richard A. Winters

There are no producing or developing mines or active mining claims in the Deschutes Canyon RARE II study area. Only two prospects were found; they have no identified potential for mineral resources. Thin diatomite deposits occur in the Pliocene Madras Formation. Development of sand and gravel deposits in the area could not favorably compete with similar deposits in the surrounding area which are closer to points of use. By mid-1982, active oil and gas lease applications covered about 25 percent of the area, a reduction from nearly 100 percent in early 1981. No holes were drilled for oil and gas exploration. INTRODUCTION Personnel of the Bureau of Mines, Western Field Operations Center conducted a mineral investigation of the Deschutes Canyon RARE II area during the summer of 1982. The area, about 10 mi (16 km) southwest of Madras, Oregon, covers 10,890 acres (4,407 ha) in the Crooked River National Grasslands (fig. 1). The Deschutes River has incised a deep canyon into the north sloping elevated lava plain near the transitional boundary of the High Lava Plains and the Deschutes-Umatilla Plateau geomorphic divisions (Baldwin, 1964, p. 20).

Jan 1, 1983

By H. C. Fuller, J. H. Jacobs

"Manganese ore from Metals Reserve stock piles at Deming, N. Mex., Cushman, Ark., and Philipsburg, Mont., were processed in the Bureau of Mines pilot plant at Boulder City, Nev., to determine their suitability for the production of electrolytic manganese. Manganese was produced successfully from all of the ores.The ores, crushed and ground to minus 33-mesh, were roasted in a Skinner furnace to reduce the manganese and were then leached with spent electrolyte, from the cells, containing sulfuric acid. Acid-leach extractions of 96 percent on Deming, 89 percent on Cushman, and 97.5 percent on Philipsburg ores were obtained. Neutralization of leaches with ammonia results in the highest manganese extraction; but Cushman and Deming leaches could not be neutralized with ammonia, because the amount required was more than enough to maintain the proper ammonium sulfate concentration. A combination of ammonia and calcine was used. However, ammonia was satisfactory for neutralization of Philipsburg leaches. Sulfuric acid needed for make-up was as follows: Deming, 0.380 pound per pound of manganese extracted when neutralized with ammonia and calcine; Cashman, 0.402 pound per pound of manganese extracted when neutralized with ammonia and calcine; Philipsburg, 0.594 round per pound of manganese extracted when neutralized with ammonia alone.All of the leach slurries settled well enough to be separated and washed in countercurrent thickeners.Impurities were precipitated with hydrogen sulfide and removed by filtration. Cushman ore solution contained only- small amounts of impurities and required 0.055 gram of hydrogen sulfide per liter of solution for purification. Deming and Philipsburg solutions contained large amounts of zinc and required 0.55 and 0.65 gram of hydrogen sulfide per liter of solution, respectively.Electrodeposition was satisfactory on all three ores and current efficiencies of 62 to 66 were obtained.A process for the production of electrolytic manganese has been developed by the Bureau of Mines, first on a laboratory scale4/ and then on a semicommercial pilot-plant scale.5/ At first the- pilot plant operated on ore from the Three Kids mine near Las Vegas, Nev., to determine the practical features of the process on ore of this type. Since completing the work on this ore, the pilot plant has been used for processing other domestic ores to obtain engineering data and other economic information regarding the amenability of such ores to the process."

Sep 1, 1946

By Thomas L. Theis

The use of a suspended growth system of T. ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor has been shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component followed by limestone neutralization is both a technically and economically feasible approach to the treatment of these wastewaters in comparison to existing and proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this report data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 9%. A cost analysis projects capital and operating costs of $80/1,000 m3 of wastewater.

Jan 1, 1982

By W. K. Connor, O&apos

The U.S. Bureau of Mines investigated the Sheep Creek prospect in the north-central Alaska Range to evaluate the Pb, Zn, Ag, and Sn resources. The studies included field investigations, mineralogical characterization, and concentration tests. Mineralization at Sheep Creek consists of disseminated, banded, and massive pyrite, sphalerite, and galena. Tin occurs as grains of cassiterite (Sn02) in the quartz-mica matrix and within pyrite and sphalerite grains, and Ag occurs in solid solution within the galena. Three bulk surface samples and two sets of core samples were collected at the Sheep Creek prospect for this study. Gravity concentration yielded products with up to 30 pct Sn, and the best result was a product that recovered 52 pct of the Sn at a grade of 22 pct Sn. Bulk sulfide flotation yielded products that recovered up to 89 pct of the Zn, 73 pct of the Pb, and 75 pct of the Ag, but grades were relatively low; selective flotation would significantly increase the grades.

Jan 1, 1989

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By Dennis J. Grigal

The goal of the program is to develop a dust collector system mounted on a ranging drum or arm shearer which will: 1) reduce the respirable dust level of the shearer operator by at least 75 percent; 2) be easily and economically mounted on an existing shearer; and 3) will not, through modifications to the shearer, reduce its safety or productive capability. The development program consists of three phases covering the activities of the design of the dust collector system, fabricating and installing it on the ranging arm or drum shearer, and conducting underground field tests on the modified mining machine.

Jan 1, 1980

By G. L. Fitzpatrick

Preliminary results of an experiment in seismic holography indicate that the techniques of acoustical holography may be successfully used with seismic waves to determine the size and general shape of underground objects. This experiment was carried out under field conditions on a moderately large scale compared with the typical laboratory experiments in acoustical holography. The object to be mapped was a 100-foot-diameter, spherical, low-velocity zone of explosively fractured rock in oil shale at an average depth of 80 feet. The seismic wavelength of the Fourier component wave used in making the seismic holograms was 50 feet at a frequency of 140 cps. The hologram sampling aperture was 226 feet square and was sampled by 441 geophones in a 21 by 21 rectangular array. One novel aspect of the experiment was the use of a wide-band polychromatic explosive source of seismic waves rather than a narrow-band quasi-monochromatic vibrator source. A successful laser reconstruction of the object image from a lensless Fourier-transform hologram in the form of a 5/l6-inch-square photographic transparency is illustrated. The size of the underground object measured from the laser reconstruction of the object and the size inferred from a knowledge of the amount of explosives used to fracture the site and the tensile strength of the oil shale are found to agree.

Jan 1, 1972