Search Documents

By Herbert H. Einstein

Rock mass deformability is commonly predicted using correlations with RQD or other indices of rock mass quality, or by extrapolation from large in-situ tests. Based on the probabilistic description of rock masses empirically developed in Part I a new approach was attempted in modeling for predictions of deformability. This approach decomposes the rock mass into spatially variable joints described by probability distributions, and intact rock blocks. Stiffnesses and elastic parameters are associated with the joints and intact blocks respectively, and deformations built up by adding the contributions of each. This model allows relaxation of many of the simplistic geometric assumptions which constrain parallel attempts to model deformation in rock masses. The model has been applied to four standard cases in order to test its results against previously existing models, and to check whether it replicates empirical correlations. When joints are taken as parallel, common empirical correlations are closely approximated by the model output. However, the closeness to empirical correlation breaks down when variability of the jointing geometry is increased.

Jan 1, 1979

By J. F. McCoy

The quantitative determination of the mass rate of flow of methane in an underground airway is calculated as the product of the methane concentration and the air flow rate. Velocities are taken at several points and then averaged over the airway cross section to determine the total volume flow. Errors in velocity measurement thereby result in errors in total volume flow as well as the mass flow rate of methane. The purpose of this program was to evaluate existing instrumentation for measuring air velocities in the speed range under 2000 feet per minute; to evaluate the method for determining total air volume flow from the velocity measurements; to evaluate new techniques which may be applied to measuring air velocities; and to design a prototype instrument which represents the best technique based on the evaluation. The instrument should be: a. portable b. self-contained c. insensitive to dust, moisture and temperature changes d. safe for use in gassy mines

Jan 1, 1972

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By T. F. Mitchell, J. A. McAllister, S. J. Hussey

"INTRODUCTION During the Bureau's extensive program of investigating possible domestic sources of manganese, an are-dressing study was conducted in its laboratories at Salt Lake City, Utah, on a sample of oxide manganese ore representative of vein material from the Ophir Hill mine at Ophir, Tooele County, Utah. The sample (obtained by blasting down and mixing a portion of the vein) was submitted by the Ophir Development Co. of Ophir, Utah. As the ore was too law in grade to be acceptable for direct production of ferromanganese, it was tested to determine its amenability to concentration by ore-dressing methods.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to Metals Reserve Company was ferrograde manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., 0.18 percent; A1203, max., 6 percent; Zn, max., 1 percent.Later, the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.0 percent iron, and 11 percent silica plus alumina. Premium were paid for manganese content in excess of, 48 percent and iron content below 6 percent, penalties being imposed upon products containing less than 48 percent manganese or more than 6 percent iron or more than 11 percent silica plus alumina. The specifications for commercial manganese further required that maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined."

Oct 1, 1947

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)' with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988

By Nicholas Kyriazi

The Bureau of Mines has been developing breathing and metabolic simulator technology since 1970. Breathing simulation has been widely achieved throughout the world and used in the testing of open-circuit breathing apparatus, but satisfactory metabolism simulation has not been achieved. This situation required that the testing of closed-circuit breathing apparatus, which are the only type used in mines, be done using human test subjects. The goal was a machine that could accurately simulate both the breathing and the metabolic functions of a human being for testing of closed-circuit breathing apparatus. The advantages of using such a machine instead of a human being for testing respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. This report will describe the breathing and metabolic simulators that have been developed and used by the Bureau over the past 15 yr.

Jan 1, 1986

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By E. L. Rawlins

The development of commercial natural-gas reserves in the Michigan stray sandstone horizon of central Michigan during the past few years has resulted in expansion of the natural-gas industry in that State. The location of the natural- gas reserves of Michigan in the general vicinity of domestic and industrial markets is of economic importance, and in supplying these markets with natural gas a reasonable knowledge of the extent and availability of the reserves is needed in formulating regulations for drilling gas wells and producing natural gas, in analyzing the feasibility of projects to construct natural-gas transmission lines, in promoting and developing markets for the domestic and industrial consumption of natural gas, and In solving many engineering and economic problems common to the natural-gas industry. The development of the natural-gas industry in Michigan has been related closely to the development of oil production. The potential oil production of Michigan is comparable with that in most of the eastern oil-producing States. The development of oil production probably will continue, especially in the central Michigan Basin area; and as wells are drilled to deep horizons in the search for oil, more knowledge will be obtained of the gas reserves in formations above the oil- bearing horizons.

Jan 1, 1936

By D. W. Frommer, M. M. Fine

"INTRODUCTION Laboratory mineral-dressing investigations covered by this report show that ores from Montgomery County, Ark., and Morgan County, Mo., are potential sources of barite and zinc. Fine grinding and froth flotation yielded drilling-grade barite from the former and chemical-grade barite and zinc concentrates from the latter.Samples from these deposits were subjected to a laboratory investigation to develop an economic and feasible treatment. The Arkansas ore, submitted by the Husky Refining Co., consisted of an intimate mixture of the economic mineral and quartz. Fine grinding and fatty acid flotation were utilized to effect a good recovery of a drilling-grade product. The other was a zinc-barite ore submitted by the Rocky Ford Mining Co., Stover, Mo. There was no problem in the recovery of zinc (most of which occurred as sphalerite), but the recovery of barite by flotation was complicated by the presence of gangue carbonates. Ultimately, an excellent recovery of barite was achieved with a relatively new type of flotation promoter, petroleum sulfonate.In recent years, barite has become one of the major industrial minerals as an essential ingredient in heavy drilling fluids, pigments, and chemicals. New sources of this important commodity are always interesting; thus, it is the purpose of this report to present information that may permit commercial exploitation of two deposits not in production."

May 1, 1952

Maps To Accompany Bulletin 494

Jan 1, 1950

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

By H. R. Beard

The Federal Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environ¬mental conflicts, impacts, and occupational hazards Associated with mining and mineral processing operations. Tailings and soil samples from Wyoming and Utah were contacted with tailings liquors to determine the degree of absorp¬tion. Absorption ranged from 0 to 99 percent for radium and from 0 to 31 per¬cent for thorium. Some samples, which readily absorbed radium, were contacted with various salt solutions that could be present in tailings solutions to determine their effectiveness as desorbents. The desorption of radium ranged from 0.06 to 100 percent. An alpha-spectrometric method was used to determine the radium and thorium, concentrations in the solutions and the solids.

Jan 1, 1979

By John C. Feeley

The methods used and the funds available for the development and oper- ation of shall mines and the reopening of small abandoned mines frequently present problems that tax the ingenuity and resourcefulness of the mining engineer far beyond that required in the mass production from large deposits. The objective of this paper is to describe in considerable detail the means whereby engineers have solved local problems in reopening an abandoned mine at which equipment, facilities, and funds were limited... The Etowah Coal & Iron Co. Gadsden red-iron-ore mine at Gadsden, Ala., 18 of interest in this category since it is the only independent red-ore mine under active development in the State. All other red-ore mines in Alabama are owned or controlled by the large iron or steel companies. The The mine, located on the southwest end of Shinbone Ridge in the outskirts of Gadsden lies in an ares once productive. but now idle, for many years. ore is relatively highgrade compared with that in the Birmingham area, but the bed is thin and somewhat lenticular. The presence of a large blast furnace at Alabama City, 3 miles from Gadsden, and the growing scarcity of red-iron ore supplies for it offered inducements for reopening the mine in 1946. Up to the time this circular was prepared (1947) only a small quantity of ore (about 1,500 tons) has been produced and shipped to the furnace. A force of 14 men was employed in sinking the main slope and developing a third "lift" (a local term for level) 100 feet below the old mine workings.

May 1, 1949

By Sam Friedman

The Bureau of Mines conducted experiments using bench-scale apparatus to explore the effect of large changes in process variables on the yield and composition of the gases produced by passing 800° C steam through a fixed bed of Pittsburgh seam (hvab) coal. The total yield of combustible gases increased throughout the given range for the following variables: Superficial steam velocity increasing from 0.02 to 0.12 fps, pressure increasing from 1,000 to 6,000 psig, residence time increasing from 0 to 60 minutes, and temperature increasing from 800° to 900° C; however, a greater increase in the yield of hydrogen in comparison with the increase in yield of methane reduced the gross heating value of the gas to around 470 Btu per scf at conditions giving the maximum yield. Pressures of 1,000, 3,000, and 6,000 psig at 0.09 fps steam velocity, 800° C, and 60 minutes residence time, respectively, produced methane yields of 20, 24, and 22 percent, based on maf coal, with the gross heating value of the CO2-free gas decreasing from 552 to 520 and to 470 Btu per scf. Methane concentrations in the CO2-free gas were 26, 22, and 14 percent, respectively. Based on the gross heating value of the coal, the percentage of the heating value recovered in the gas was 60, 71, and 87 percent, respectively. The use of tungsten sulfide as a catalyst for converting carbon oxides and hydrogen into methane was explored briefly using both a sulfur-free gas rich in methane and a sulfur-bearing synthesis gas (3H2:1CO).

Jan 1, 1968

By G. W. Jones

The Bureau of Mines has advocated the use of stenches as warning agents in metal mines and in gas-distribution systems since 1920 A considerable amount of research has been conducted on ethyl mercaptan and other compounds to determine their effectiveness when used for this purpose.4/5/6/7/8/9/10/11/12/13/ Miners are warned of danger by a stench injected, in measured quantity, into a compressed-air line through which it is rapidly carried to the working faces, where it escapes from the compressed-air equipment and imparts a characteristic odor to the air. This method is not applicable to mines where only a limited number of com-pressed-air lines are used, as for example, many coal mines; the ventilation currents available in these mines may be too slow for warning purposes.14/

Jan 1, 1954

By A. R. Rule

Research was done by the Bureau of Mines to determine the effect of a low-molecular-weight polymer on wet grinding of quartz, dolomite, and a copper ore. A 5-in ball mill equipped with a torque sensor for precise measurement of input energy was used for batch grinding tests. Grinding parameters were determined from size distribution data on the feed material and ground product. Zeta potential measurements were made to determine the effect of the polymer on the surface properties of the three materials, and a viscometer was used to measure the effect of the polymer on slurry viscosity. The addition of the polymer caused a sharp increase in the negative value of the zeta potential for all three materials, indicating that pronounced adsorption was taking place. At a constant slurry percent solids, addition of the polymer caused a similar reduction in slurry viscosity for each material. For quartz, dolomite, and the copper ore, grinding efficiency, as measured by kilogram of product per kilowatt hour passing a given screen size, was not affected by the addition of the polymer. However, the lowering in slurry viscosity caused by addi-tion of the polymer permits grinding at a higher slurry percent solids.

Jan 1, 1985

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By D. R. Tesarik

The factor of safety, the traditional measure of stability for earth embankments, is graphically presented in factor of safety charts in this Bureau of Mines report. Factor of safety contours are drawn for homogeneous earth embankments for two contrasting situations: (1) no phreatic surface and (2) a phreatic surface that assumes 10-pct freeboard. The factor of safety can be read directly from the charts if the physical properties of the soil and the geometry of the embankment are known. The curves provide a quick first approximation of the "most stable" and "least stable" condition of the embankment. The Simplified Bishop Method was used for the safety factor calculations, and a sequence of least squares curve fitting steps was used to present the factor of safety in final chart form.

Jan 1, 1981

By L. C. IlsLey

Permissible electric nine lamps are approved with the. understanding that if actively marketed they will be listed in Bureau of Mines publications so that state mine departments, compensation bureaus, mine operators, miners, and others interested in safety equipment for mines may know the permissible lamps available and the important safety features of each. The last list of permissible electric mine lamps was issued as Report of Investigations 33045 in June 1936, a supplement to Bulletin 332.6 All lamps described in Bulletin 332 are either obsolete or have been materially modified, as covered by extensions of the original approvals. These modified lamps and the new designs approved since 1930-totaling 12 cap lamps and 23 lamps of miscellaneous types-comprise the present list of actively marketed permissible electric mine lamps. This bulletin presents the Bureau's test requirements and procedure relative to permissible electric mine lamps and describes briefly the lamps, giving tabulated details of each.

Jan 1, 1942