Search Documents

By M. R. Geer

The use of the cyclone as a dense-medium cleaning device was first described by Driessen6/ in 1945, after development of the process in the Netherlands during the German occupation of World War II. A pilot plant was built in the Netherlands soon thereafter, and the first commercial plant was built in 1948. By 1958, 18 plants were operating or under construction.7/ Thus, economic factors in Europe, where the high cost of coal places a premium on efficient cleaning, dictated rapid adoption of the cyclone. American reception of the process differed. The Bureau of Mines presented the results of its own small-scale cyclone experiments in 1946;8/ showing a sharp separation between coal and impurity; adoption by industry now is taking place. There is now much greater emphasis on the efficient cleaning of fine coal, and the first American cyclone plant has begun operating; others are planned or under construction. With the present interest in improved treatment of fine coal, the Bureau of Mines felt that additional performance data on the cyclone would be helpful to industry. Therefore, a complete, open-circuit pilot plant was built to make cleaning trials on American coals covering a wide range of washability characteristics. Five raw coals and one middling product were included in the investigation, and each was cleaned at several densities; 17 cleaning trials are reported.

Jan 1, 1961

By R. V. Higgins

"INTRODUCTION When nations throughout the world are pitted against each other in a war in which petroleum plays a major role, scientist and engineers of the petroleum industry must give serious thought to ways and means for recover¬ing greater percentages of oil from natural reservoirs than in the past. Petroleum and its products are vital to highly mechanized modern warfare, and the victorious nations will be those whose armies, navies, and air forces are supplied with adequate fuel oil, gasoline, and lubricants until the war is won.Efficient recovery of oil from underground reservoirs depends on many interrelated techniques; evaluation of the producing performance of wells upon the basis of their productivity indexes is one such tool. Oil wells usually yield oil at a maximum rate when first ""brought in"". The rate of production begins to decline soon after the first oil is delivered to the tanks, and although part of the decline usually can be attributed to natural reduction of reservoir pressure as oil and as are withdrawn from the reservoir, a larger proportion frequently is caused by greater saturation of water and as in the producing formation about wells and clogging of the pores of the sands by silt, organic salt, and insoluble hydrocarbons. If the maximum quantity of oil is to be recovered from reservoir sands and rocks by wells, it is then imperative that the ability of wells to produce oil be watched closely and all adverse influences that affect the case with which oil can flow to wells be corrected if possible."

Sep 1, 1942

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By J. C. Johnson, W. G. Pariseau, D. F. Scott, F. M. Jenkins

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 1993

By R. C. Hickman

"INTRODUCTION .As part of its spot drilling program, the Bureau of Mines core-drilled seven holes on the Alexander and Barber properties in Spartanburg County, S. C.Extensive surface float and outcrops of sillimanite schist on these properties appeared to justify drilling, which did not prove satisfactory, however, owing to the spotty occurrence of the schist bodies and the poor core recovery in the decomposed schist.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.This project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Alexander and. Barber properties are in the southern part of Spartanburg County, S. C. The Alexander property is about 5 miles cast of Woodruff. It is reached from Woodruff by driving east 5 miles on a macadam road to the intersection with an unsurfaced road near Unity Church. The farm house on the property is 0.4 mile north on this road. The sillimanite outcrop is in a field approximately 1,200 feet east of the farm house. The Barber property is about 2 miles north along the unsurfaced road that passes the Alexander property."

Sep 1, 1947

By W. W. Odell

"It is common knowledge that extensive lignite deposits occur in the States of Montana, North and South Dakota and Texas. The total area of these deposits and the total amount of lignite in them is so great that the true economic value of lignite is seldom realized. These deposits underlie areas of thousands of square miles. The area of the lignite lands in North Dakota alone is estimated to be approximately 32,000 square miles. Nearly one-third of the total solid-fuel resources of the United States is lignite and approximately 90 per cent of this lies in the Northwest.To the people of the Northwest the more extended utilization of lignite is of fundamental importance, hence any methods for commercially producing salable products from lignite that promise further development of these great fields deserve careful study.The development of our lignite resources has been slow, partly because the districts wherein lignite is found is not thickly settled or highly developed in manufacturing industries, but also because of the physical and chemical characteristics of the lignite. Lignite is classed as a low-grade fuel and may be con¬sidered as imperfectly developed coal -which has a more or less woody structure; it may be of the brown-coal type or darker, denser and more homogeneous, approaching subbituminous coal in character. As mined it contains more than 30 per cent of moisture exclusive of the -rater of decomposition formed .then it is carbonized or burned. The heating value as determined by the calorimeter is approximately half that of good quality bituminous coal. Upon exposure to the air lignite loses part of its moisture, whereupon the lumps chock and split until after considerable exposure, a large percentage of slack is formed. It cannot be stored in large piles so successfully as come other fuels, and it some instances it is more apt to ignite spontaneously in storage or in transit then the higher grade fuels."

Feb 1, 1924

By S. H. Lorain

The Minah silver-lead mine in the Wickes district, Jefferson County, Mont., produced substantial quantities of silver-lead ores in the 1890's. The mine has been abandoned since the "silver panic" of the early 1900's. As a part of the Bureau of Mines: program to develop new sources of lead to overcome the growing shortages of that metal, a development project was started at the Minh mine in April 1946 and continued until June 1947, during which 5,600 feet of angledozer trenching and. 1,093 feet of core drilling were completed on the main vein and nearby parallel veins: As a result of this work, interest in the property was stimulated and private operators are now engaged in reopening the mine. This report discusses the past history, geologic setting, and the recent and early operations of the mine.

Jan 1, 1948

By C. P. Haller, S. J. Aresco

"INTRODUCTION The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heat¬ing value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the fusing temperature of ash and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions./ issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made.Analyses of the delivered coal and ""tipple"" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. Moreover, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.The Government purchased approximately 5-1/2 million tons of coal in fiscal year 1951. In connection with these purchases, the Bureau analyzed 10,700 samples. These are published for the use of Government officials and the public. A series of publications s been completed on coal analyses by States, or, where production is small in any State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications contain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals.The technical papers published by States, with their numbers are: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio, 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement, 645); Pennsylvania Anthracitic, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supple¬ment, 618); West Virginia, 405 and 626; and Wyoming, 484."

Feb 1, 1953

By Lucia Kuizon

The Pinnacles Wilderness Contiguous Wilderness Study Area (WSA) (CA-040-303) is 30 miles south of Hollister, CA, in San Benito and Monterey Counties. It is composed of five parcels of public land totaling 5,838 acres adjacent to the Pinnacles National Monument. The U.S. Bureau of Land Management later reduced the size of the Recommended Suitable Area (RSA) to 2,200 acres. U.S: Bureau of Mines personnel examined the entire WSA in May 1984. The WSA is underlain by Tertiary sedimentary and Cretaceous plutonic rocks. Diatoms occur in interbedded tuff, shale, and sandstones in the northern part of the WSA, but outside the RSA. In 1984, there were no mines, prospects, mining claims, leases, or mineral resources in or within one mile of the study area. No energy minerals were identified; however, an oil well was drilled in 1951 in the northern part of the WSA, but outside the RSA; it was a dry hole.

Jan 1, 1985

Rock property tests were performed on NX-size diamond drill core from the roof, floor, and coal from the longwall mining section of Federal No. 2 mine, West Virginia. The purpose of these tests was to determine the engineering properties of the various strata as part of a ground control study of the longwall operation. The following tests were performed: 1. Uniaxial compressive strength, Young's modulus, and Poisson's ratio 2. Triaxial compressive strength 3. Brazilian tensile strength 4. Modulus of rupture 5. Specific gravity Thirteen boxes of core delivered to the University on April 1, 1974 were identified as follows: 2 PTR 1 -2 boxes of roof rock 2 PTF 1 -2 boxes of floor rock 2 PTR 2 -2 boxes of roof rock 2 PTF 2 -2 boxes of floor rock with approximately 3 ft of coal in Box 2 (designated 2 PTC 2) 2 PTR 3 -2 boxes of roof rock 2 PTF 3 -2 boxes of floor rock 1 PC 5 -1 box of coal

Jan 1, 1976

By Thomas J. Peters

The Snowbank study area, which had been proposed as Wilderness, lies about 5 air mi southwest of Cascade, Idaho, and about 60 air mi north of Boise. The eastern boundary of the north-south-elongate study area lies 1-to 2-mi east of Cascade Reservoir; the western boundary is contiguous, in part, with the western boundary of Valley county. The 8,200-acre study area is underlain by Cretaceous granitoid rocks of the Idaho batholith. Three prospects were found in or near the study area during a library and field search. Gold occurs at one 30-ft adit, but the gold-bearing structure appeared too narrow to contain resources. Two other prospects appeared essentially unmineralized. No evidence of geothermal activity was observed. Rock in the area is not potentially useful as dimension stone because it does not split into flat slabs. To be used as aggregate, the rock would require crushing and hauling to distant markets. One of 18 alluvium concentrate (placer) samples contained free gold, worth $1.07 per cubic yard of gravel (at a $350 per oz gold price). No alluvial bars were seen; deposits were too small to contain gold resources or be considered gravel resources.

Jan 1, 1993

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By William Cochran

The mineral waste disposal system at the Grace Mine, Morgantown, Pa., was designed to minimize environmental effects while allowing much of the waste from the iron mine, mill, and concentrator to be utilized. Standard cost estimating procedures were used by the Bureau of Mines to determine waste disposal costs. Mill tailings and rock waste disposal costs were estimated at $0.151 and $0.276 per ton, respectively, for the 1965-67 production period. Total waste disposal cost was reduced about $0.015 per ton by utilizing part of the waste as aggregate. The net average cost for disposal of all mineral waste was $0.189 per ton.

Jan 1, 1969

By Efrem R. Reeves

Noise-induced hearing loss (NIHL) is the most common occupational illness in the United States, with 30 million workers exposed to excessive noise levels [NIOSH 1996] every day. Of particular concern is the mining industry; which has the highest prevalence of hazardous noise exposure of any major industry sector [Tak et al. 2009] and is second only to the railroad industry in prevalence of work-ers reporting hearing difficulty [Tak and Calvert 2008]. This document is for operators, safety personnel, and mechanics in the mining industry who are not specialists in noise control engineering or acoustics. Evaluations of successful and unsuccessful attempts at controlling noise on several large, underground metal mining machines are detailed to illustrate the basic principles of noise control. Once personnel understand the guidelines and principles of noise control, they will be able to ¦evaluate the extent of a noise problem; ¦determine the best approach to the problem; and ¦apply the most appropriate solution. Because of the insidious nature of NIHL, it can go unnoticed until a considerable loss of hearing has occurred. In some cases, diagnosis is delayed because an exposed individual claims to have become accustomed to the noise. In reality, that person may have already suffered irreversible hearing loss. Humans can hear sounds in the frequency range from about 20 to 20,000 Hertz (Hz). Within this range, NIHL usually begins in the frequency region around 4,000?6,000 Hz, the upper levels of the speech region. The first noticeable symp-toms include difficulty understanding higher pitched voices, such as the voices of females and children, and difficulty understanding certain consonant sounds, which are primarily high frequency in nature. The extent of NIHL varies depending on the level and duration of noise exposure and on an individual?s susceptibility; despite having similar noise exposure, individuals can experience differing degrees of hearing loss, or none at all. NIHL is almost always preventable. To reduce or eliminate the possibility of NIHL, an individual?s noise environment must be analyzed and appropriate action taken to reduce noise exposure.

Dec 1, 2009

By C. Edward Chamberlain

A Bureau of Mines procedure was developed for the analysis of volatile matter in airborne coal dust-rock dust mixtures prior to, and resulting from, coal mine fires and explosions. Dust in the 10-to 20-mg weight range can be analyzed. Volatile matter is determined by a greatly scaled-down version of the empirical macro-scale method used by the Bureau. The alkaline earth carbonates in the rock dust are dissolved in acid prior to the volatile matter determination of the residue, and the rock dust content is calculated from the analysis of calcium and magnesium by atomic absorption.

Jan 1, 1974

By J. L. Eakin

Systematic flooding was introduced into Nowata County, Okla., in May 1931. The results of this means of stimulating the nearly depleted Bartlesville reservoir in the county has been the subject of four Bureau of Mines Reports of Investigations.2-5/ This report presents a discussion of four full-scale water-flooding projects in the Delaware-Childers field and 1 pilot project in the Curl Creek field (fig. 1). All five plants have been in operation for only a few months. Although substantial increases in the rates of oil production have been obtained 1 by the injection of water, the projects are of particular interest at this time because of the novel methods of operation and new equipment that are being employed. One project utilizes a portable "package" plant designed for a pilot operation. All of the controls for this project are centrally located. The design makes it possible to remove the test plant to another location if the project is unsuccessful or if the unit is to be replaced by a larger plant. This project also utilizes diatomaceous-earth filters successfully for the first time and makes use of plastic pipe. Another novel feature of the operation is the aeration of Arbuckle limestone water through an airlift in the supply well.

Jan 1, 1955

By J. R. Long

The Federal Bureau of Mines has pioneered the work of preparing ductile titanium on a large scale and has also determined the basic properties of this new and most interesting metal. A number of reports (1, 2, 3: 4, 5) have al-ready been published, and considerable interest has been aroused in a number of industrial and research laboratories. Some of these laboratories have also published results of their work on the pure metal. Although the properties of titanium itself are quite promising, it is apparent that considerable improvement may be expected by alloying titanium with other metals. That is, pure metals in general have shown relatively large improvements in properties when alloyed with other metals and titanium is not considered to be an exception to the rule. Therefore, the emphasis of the investigations now under way in the Federal Bureau of Mines Laboratories has been placed on the study of the alloys of titanium, particularly the titanium-rich alloys. While the main interest is in the properties of such alloys, proper direction and evaluation of the work require at least a rough outline of the phase boundaries of the alloy systems involved.

Jan 1, 1949

To reduce the respirable dust generated by auger-type continuous coal mining machines. The Approach: Use water sprays close to the cutting bits on the auger so that coal fragments are thoroughly wetted as they are formed to prevent dust dispersal into the ventilating air. How It Works: The "wet auger" system of dust control uses water sprays distributed on both shafts of auger type continuous miners. This approach has been tested underground by personnel of the Bureau's Twin Cities (Minn.) Mining Research Center on a Wilcox Mark 20 continuous miner, in a cost sharing contract with Buchanan & Sons Coal Company, Inc. Personnel of the Interior Department's Mining Enforcement and Safety Administration collected dust samples and analyzed the data. A test machine was fitted with six sprays on each auger (see Fig. 1). Water flow rates from 8 to 12 gpm at pressures from 90 to 120 psi, or about 8 gallons per ton of coal mined, were required. At these rates of water usage, mining personnel experienced no problems with work-

Jan 1, 1974

By David Montgomery

The feasibility of building a calibrator for the DuPont D-100 audio dosimeter is discussed. The desired specifications are used as guidelines but the possibility of their relaxation is also considered. Commercially available equipment is surveyed and found to not satisfy the guidelines. Several alternate concepts are investigated, and recommendations for further work are presented.

Jan 1, 1974