Search Documents

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

By J. W. Paul

Mine foremen are employed in coal mines for two reasons: First, so that the underground work. may proceed in an orderly manner and that each employee gives attention to his duties; and second, by reason of the State law which re- quires the employment of such officials to see that the laws relating to safety are carried out. It may be seen that, with these two duties, the foreman has wide scope of authority and much responsibility. As foreman of operations he has to meet certain economic questions that contribute to the cost of producing the coal, and as the agent of the State he must also supervise and coordinate the work in such manner as to insure that the employees work under safe conditions. As the roof of coal mines is the source of the greatest hazard naturally the care of the roof must take much thought and planning on the part of the fore- man; and this circular is therefore presented to call attention to some things he may do to prevent injury to the workmen by falls of the roof material or coal. Mine foremen, in the principal coal-producing States, are certified by a State board which prescribes certain qualifications, experience, and character, attested by examination and personal endorsement. Certified foremen, therefore, are men who have had experience underground and know roof conditions and timber- ing methods. The suggestions herein are based upon observations made at many mines and collectively embrace practices that have been found to be in effect and pro- moted by experienced mine foremen:

Sep 1, 1930

By O. S. North

As recently as the late 1920's there Were few indications that a 15-million-dollar-a-year industry would ever grow out of the mineralogic curiosity vermiculite. Today, it is an important industrial commodity, used primarily as an insulating material and lightweight aggregate, but with a wide range of other applications. The quantity of crude vermiculite produced and used in the United States increased 14-fold in the 17 years between 1935 and 1951. The vermiculite minerals are of secondary origin, formed by hydrothermal alteration of an ultrabasic igneous rock, generally pyroxenite, or by alteration of phlogopite or biotite mica or possibly other similar minerals. According to different authorities, vermiculite may originate either by direct hydrothermel means, by the weathering of biotite or phlogopite, or by a combination of these two agencies. Vermiculites frequently occur at or near the contacts of an acid intrusive rock, especially a pegmatite dike, with a basic or ultrabasic country rock.

Jan 1, 1953

By W. J. McConnell, C. P. Yaglaglou

"IntroductionThis paper on the kata thermometer is issued by the Bureau of Mines on account of the general interest in this instrument and the fact that it is frequently used in studies of mine ventilation conditions with regard to comfort and health of miners. It has been used in the studies being conducted along this line by the Bureau of Mines on the effects of high temperatures and humidities of air in mine working on the comfort conditions, as well as in studies of atmospheric conditions in mine, railway and vehicular tunnels.The study of the various physiological responses of the human body to different degrees of temperature combined with different percentages of relative humility in still and in moving air, now being conducted at the Pittsburgh experiment station of the bureau in the research laboratory of the American Society of Heating and Ventilating Engineers, cooperating with the Bureau of and the U. S. Public Health Service, presents an added opportunity of investigating the instruments that have been devised to measure atmospheric conditions as they affect the comfort and health of human beings.The ordinary mercury thermometer, as pointed out by Heberden3 almost hundred years ago is a very inadequate instrument for measuring the physiological effects of atmospheric conditions. It merely accounts for that part of the body heat lost by raliation and convection, while as a matter of fact greater part of the body heat resulting from the metabolic process within the body is eliminated by means of evaporation from the surface of the body."

Jan 1, 1924

By Paul E. Bennett, James S. Browning, Thomas L. McVay

Continuous 1.0- to 1.5 - ton - per - hour pilot plant flotation tests were made to determine the technical and economic feasibility of recovering beryl from flotation tailing being produced at the spodumene concentrator of the Foote Mineral Company , Kings Mountain , N.C. Best results were obtained when using an acid circuit and amine - type cationic reagents to float a bulk beryl - feldspar concentrate and then selectively floating the beryl away from the feldspar , using a petroleum sulfonate collector . About 77 percent of the beryllium in the pilot plant feed was recovered in a concentrate containing 6.42 percent BeO . The capital cost of an integrated flotation plant capable of treating 500 dry tons of spodumene mill tailing per day for recovery of beryl and feldspar is estimated at $ 210,000 . Indicated direct operating costs for the plant were $ 1.52 per ton of dry spodumene flotation tailing treated . This approximated the value of beryl recovered , but potential profits of about the same magnitude lie in concurrent recovery of marketable spodumene and feldspar byproducts .

Jan 1, 1964

By P. L. Swanson

Over a recent 20-month observation period, the U.S. Bureau of Mines obtained seismogram records from a single vertical-component, short-period seismometer installed at the surface of a metal mine in northern Idaho. The seismic events were analyzed for local (Richter) magnitude (M), time of occurrence, location, and relation to rock bursting and production blasting. Approximately 150 seismic events with -0.5 = M = 2.9 were located within the mine, yielding a b value (slope of the logarithm of the number of events with magnitude greater than M versus M) of 0.5. Event locations were constrained using a dense underground array of high-frequency accelerometers. Twenty of the surface-recorded events, with 0.5 = M = 2.9, were associated with rock bursts that produced damage requiring at least 1/2 day of cleanup and/or repair. Other possibly hazardous rock bursts, with magnitudes as small as -1.1, were numerous but were not associated with significant structural damage. Approximately 60 pct of the seismic events with M > -0.5 and 75 pct of damaging rock bursts occurred within 45 min of blasting. Estimates of characteristic rupture dimensions for rock bursts with -1.1 = M = 2.9, based on a conventional dislocation shear-slip model of failure, range from 3 to 300 m.

Jan 1, 2010

By William Seymour

"INTRODUCTION Byproduct-coke manufacture is one of our country's most essential in¬dustries; its importance was strikingly accentuated by the demands of World War II. This paper reviews recent progress in various phases of byproduct-coke operations for the production of metallurgical coke particularly that used as blast-furnace fuel.In the early days of the by-product-coke industry in the United States high-grade bituminous coking coals, both high-volatile or gas coal and low-volatile Pocahontas coal, were plentiful, and the selection and mixing of coals for coke-oven use were minor problems.The demands of World War I for the production of iron, steel, and coke aroused and stimulated new interest in the investigation of the reserves, characteristics, and properties of our coking coals. During that war the increased demand for coke reached a critical stage, and the shortage of high-grade coking coals necessitated the use of cols of inferior quality and of different coking characteristics than those previously used.The period of prosperity following World War I brought much progress and development in the by-product-coke industry. Methods of testing coal and coke were improved. The search for satisfactory coking coals was continued, and construction and design of byproduct ovens were improved."

Jun 1, 1946

By R. C. Corey

GERMANIUM is an element that has come into widespread use in the electronics industry in recent, years. So far this increasing demand has been, met by ample supply: however, the future balance is uncertain, and the need has been recognized to discover additional domestic sources of germanium. This investigation was conducted to study the possibility of obtaining a potential supply of germanium from coal or coal ash. It has been known for some time that coal contains germanium; the discovery that By ash from coal-fired boilers often contains appreciably more germanium than the original coal suggested the possibility that coal ash might be an abundant and economical source of this element. In this study the concentration of germanium was determined in numerous samples of coal and ash. A number of miscellaneous waste materials also were examined in the course of the investigation; the results are reported as a matter of general interest. The methods and equipment employed are discussed in detail. Sample-preparation and analytical techniques are described in the appendix. Spectrographic analyses were made on a total of 639 samples, including coal, coal ash, slap ash from lignite and peat, wood ash, and various inorganic materials. Qualitative analyses were run on all samples, and quantitative determinations were made on those samples that contained enough germanium to be measured by this method The lower limit at which germanium can be determined quantitatively by spectrographic analysis is 50 parts per million (p. p. m.), but concentrations of less than 20 p. p. m. can be detected qualitatively.

Jan 1, 1959

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By Frank E. Chase

Kettlebottoms are columnar masses of rock--the preserved casts of ancient tree stumps--embedded in coal mine roof strata (of which they are a part). Because unsupported kettlebottoms can detach from a mine roof without warning, they are a hazard to miners. The primary objectives of this investigation were (1) to better define and describe kettlebottoms and (2) to evaluate kettlebottom support techniques in terms of safety and effectiveness. A telephone survey of mine operators, interviews with Mine Safety and Health Administration (MSHA) personnel, and underground mine visits were conducted in Pennsylvania, West Virginia, and Kentucky. Information gathered during this investigation indicates that the size and frequency of kettlebottoms in mine roof are dependent upon past geologic events and biological processes active during the deposition of roof sediments. To ensure the safety of mine personnel, all undermined kettlebottoms should be supported. The roof should be bolted next to kettlebottoms less than 3 ft in diameter, close enough to allow a portion of a wood or steel header to be extended beneath each kettlebottom for support. Two bolts and a wood plank or steel strap should be employed to support kettlebottoms over 3 ft in diameter.

Jan 1, 1983

By Arthur V. Petty

The Bureau of Mines has researched the utilization of mining and pro-cessing wastes as raw materials for the production of glass-ceramic pipe. Characterization of various wastes as to occurrence and chemical composition is reported. A computer program was developed and used to identify waste materials and mixes that would result in glass melts from which glass-ceramics could be produced after cooling and subsequent heat treatments. The production of abrasion-resistant pipe from inexpensive and readily available domestic resources could offer an economical substitute for high-alloy steels containing the critical and strategic materials cobalt and chromium.

Jan 1, 1984

By Lowell Stroud

Ten natural gases containing from 0.023 to 8.4 percent helium were investigated. In seven high-helium samples, the isotopic abundance of Ne21 was greater than in the atmosphere, being supplemented by 33 to 85 percent of "excess" or "radiogenic" Ne21. The ratio of He4/Ne21(rad) in these gases was evaluated and found to vary between 2.9 x 107 and 5.9 x 107 , a factor of approximately 2. Argon concentrations were determined by the isotope dilution method. The isotopic ratios of Ar40/Ar36 in the high-helium gases were from 5 to 75 times the atmospheric value, with the Ar40 being about 80 to 99 percent radiogenic in nature. The ratios of He4/Ar40(rad) in all 10 gases were evaluated and found to range from 4 to 18. The isotopic ratio of N14/N15 in four of the high-helium gases was essentially the same as in the atmosphere; in three cases it was approximately 5 percent higher than the atmospheric value of 272.0. The genesis of nitrogen and the relationship of nitrogen to helium in natural gases were reviewed and are discussed in terms of a theory for the concurrent generation of nitrogen, helium, radiogenic neon 21, and petroleum (hydrocarbon gases and liquids).

Jan 1, 1967

By Martin Berman

Tables of 28 positions for all the transitions for nine common analyzing crystals for first, second, and third order reflections were compiled by the Bureau of Mines to facilitate elemental X-ray fluorescence analysis on multi-element systems. The tables are based on a compatible set of wavelengths for 2,346 observed X-ray transitions of the elements lithium to americium. The results are tabulated in order of increasing wavelength as well as by increasing wavelength for each element.

Jan 1, 1969

By Patrick A. Hamilton

This Bureau of Mines report delineates the coal reserve base of anthracite, bituminous and subbituminous coals, and lignite, by mining method and sulfur content, for coal-bearing States west of the Mississippi River. The parameters used to establish the reserve base definition are the result of a joint agreement by the Federal Bureau of Mines and the U.S. Geological Survey. The reserve base of low-sulfur coal, =10 percent sulfur, is 167,324.5 million tons; medium-sulfur coal, 1.1-3.0 percent sulfur, is 37,531.5 million tons; and high-sulfur coal, >3.0 percent sulfur, is 11,244.1 million tons. The reserve base of coal with an unknown sulfur level is 18,323.0 million tons. The percentages of deep and strippable coal are 56 percent and 44 percent, respectively. The basis for reserve base estimates and analytical data for this report was the Fuels Availability System, a Bureau of Mines data bank containing numerous data tin fossil fuels. Information contained in the system was obtained from publications of the Bureau of Mines, U.S. Geological Survey, State agencies, private publications, and company data.

Jan 1, 1975

By S. J. Hussey

Since the discovery in 1935 by Adams and Holmes that certain synthetic resins exhibit ion-exchange properties, many applications of the ion-exchange process have been made. There are two general types of ion-exchange resins. Cation exchange resins adsorb cations from solution, and these in turn may be replaced by other cations adsorbed under certain conditions. 'Anion exchange resins adsorb acids from solution, and the anion of the acid may then be replaced by other anions. It is reported, however, that certain anion exchange resins have a low capacity for anions of weak acids without the necessity of acid adsorption either directly or as an intermediate step. The adsorbed ions may then be removed from the resins by elution with an appropriate solution, and the resin is prepared for the next adsorption cycle by regeneration with another solution. Sometimes one solution, is used to simultaneously perform the functions of elution and regeneration. The first and probably the largest application is in the field of water purification. Other applications have been made in the production of high-quality foods for human consumption, in the recovery of valuable substances from solutions, in the separation or fractionation of electrolytes, and in several other fields, each of which has its specific applications, variations, and possibilities. Ion exchange resins also have been highly useful in perfecting techniques of laboratory analysis and research.4/, 5/, 6/

Jan 1, 1948

By Richard F. Link

A statistical technique, useful to analyze assay and other data characterized by location in three dimensions, is described in this Bureau of Mines report. If present, trends in the data are defined for the purposes of improving ore estimation, predicting ore beyond existing workings, and aiding geological interpretation. The technique is to fit linear and quadratic polynomial equations to the data through the statistical method of regression analysis. The fitted linear equations have the geometric form of hyperplanes; the fitted quadratic equations have the geometric form of ellipsoids or elliptic hyperboloids of one or two sheets. To visualize these three-dimensional forms, contour maps of a series of plane sections through the fitted surfaces are plotted. Both the fitting of the polynomial equations and the plotting of the con-tour maps are done by electronic computer to facilitate calculations and to obtain accurate results. Computer programs are described in appendixes. Methods employed are illustrated by an example analysis) based on data from a part of the Fresnillo mine) Zacatecas, Mexico.

Jan 1, 1966

By W. J. Wenger

THIRTY-FOUR analyses of crude oils from the fields of the Four Corners Area of Arizona, Colorado, New Mexico, and Utah are presented and compared. The samples, taken from formations in four geological time periods, have high gravity and low-sulfur, -nitrogen, and -asphalt content. Generally, the oils are paraffinic in the low-boiling fractions, with increasing naphthenicity in the higher-boiling fractions. Oils from Cretaceous formations resemble other Cretaceous oils in the Rocky Mountains, but oils from Permian and Pennsylvania formations are unlike other oils of these ages in the Rooky Mountains. The differences in the oils are minor and cannot be used to distinguish between fields or between producing formations. With minimum special processing, the oils should yield large amounts of good-quality motor fuels. INTRODUCTION The only place in the United States where four States have a common junction is known as the Four Corners Area. This area (fig. 1) includes the northeast corner of Arizona, the southwest corner of Colorado, the northwest corner of New Mexico, and the southeast corner of Utah. It includes three major geological basins: The Black Mesa, the San Juan, and the Paradox. Major oil developments have occurred in both the San Juan and Paradox basins, but no discovery of commercial importance has been made in the Black Mesa basin.

Jan 1, 1960

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959

By Kenneth E. Hay

The Bureau of Mines collected coal and coal waste aggregate material from two different mine sites to determine their strength characteristics for use in concrete. The concrete would be placed underground as support walls for ground control in adverse conditions or unique mining applications. A standard mix design was established for a "wet" mix using a water-to-cement (w/c) ratio of 1.0 to facilitate pumping into place. Later, material was collected from four more mine sites and used to make 2-by 2-by 2-ft test blocks with the same w/c ratio. A pull-out cone device and borehole shear tester were used to determine the in situ material strength of the test blocks. These techniques will provide a simple and quick way of determining support wall strength in an underground environment. Test results from the pullout cone de-vice showed a good correlation of 0.98 to test cylinder compressive strengths of the same mix. Results of the borehole shear tester were inconclusive.

Jan 1, 1986

By Charles C. Myers, Robert M. Doerr

The apparatus described was developed for determining the kinetics of gas - solid reactions at high temperatures by measuring the volume of gas consumed with respect to time . This apparatus consists essentially of a horizontal precision- bore glass tube connecting a small reaction chamber in a furnace to a large constant - temperature reservoir . A drop of mercury in the tube separates the two sides of the system and serves as an indicator that moves at a speed proportional to the rate of gas consumption . The sensitivity of the apparatus depends inversely on both the density of the gas in the system and the cross - sectional area of the tube ; with a tube having an area of 0.079 cm² , the sensitivity for oxygen at 308 ° K and 0.5 atm is 20 cm/mg . The reproducibility of data with the volumetric apparatus is good .

Jan 1, 1964