Search Documents

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By J. M. Singer

Methods are proposed for predicting concentrations of nitrogen oxides and carbon monoxide in the combustion gases of flames, specifically of lean, stoichiometric, and rich propane-air flames. Calculations are based on kinetic and thermodynamic theory. These theoretical data are compared with concentrations observed experimentally downstream of flat grid-type burner flames (approximately 25,000 Btu/hr) that were used to simulate gas appliances such as water and space heaters. Air pollutant concentrations are also computed for (1) flames chemically perturbed by recycling flue gases into the primary fuel-air mixtures; (2) flames thermally perturbed by cooling the burned gases at different rates; and (3) flames perturbed by combination of these two effects. In general, experimental and computed concentrations agree to within a factor of 2 to 7 with the experimental values always being higher than the theoretical. The theoretical analysis indicates that cooling the primary flame by recycling cold flue gases (with and without excess air) reduces the relative emission of nitric oxide and increases emission of carbon monoxide if the flame stoichiometry does not radically change. Cooling rates of about 5,500° to 10,000° R/sec starting at about 3,500° R generally suffice to prevent nitric oxide concentrations in lean flames from increasing much above the initial values at the combustion zone; these same cooling rates do not prevent oxidation of most of the initial carbon monoxide.

Jan 1, 1967

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By J. M. Singer

Thermal, mechanical, and physical properties of virgin and heat-treated Pittsburgh seam coal were determined as part of a comprehensive study of combustion of monolithic coal block. The information was sought to help characterize pyrolysis and combustion processes in underground coal mine fires but should also prove useful in the study of in situ and surface coal gasifiers. Measured properties include thermal conductivity, specific heat, thermal expansion, density, compressive and tensile strength, porosity, and permeability. The transport property data were obtained (when feasible) in two mutually perpendicular directions of the anisotropic virgin coal material, and coal samples carbonized for 5 hours at temperatures of 350° C, 475° C, 500° C, 650° C, and 850° C. Other coals (Pocahontas No. 3, Sewell, and Illinois No. 6 seams) were investigated for porosity and relative permeability. Interdependence among all properties was evident from the results; however, only a few correlations could be developed owing to inhomogeneity of coal material and specimen variation, which had the effect of reducing the accuracy of measurement and increasing data scatter.

Jan 1, 1979

By A. L. Engel

In previous reports5/ of ore-testing studies, tests made by established methods on typical ores selected as representative of certain mining districts have been described in considerable detail. In addition to established test procedures, such as screen analysis, chemical analysis, microscopical examination of ores and products, sink-and- float separation, gravity concentration, flotation, ,and magnetic separation with or without roasting, it was sometimes necessary to apply other methods, such as leaching, in instances where physical separations were not feasible.

Jan 1, 1940

By A. A. Cochran

Bureau of MinesThe Bureau of Mines studied the development of practical methods for recovering manganese from the extensive domestic resources of low-grade ores and open hearth slags. A one-step operation was developed on a laboratory scale in which manganese and iron compounds are treated with chlorine, volatilized, and separated by selective condensation. Manganese recoveries of 90 to nearly 100 percent were obtained from 9 of the most important domestic ores. Analyses of the manganese chloride product indicated that it was suit-able for aqueous electrolysis with little additional purification. A complete, integrated process that provides for the recovery and recycling of chlorine is proposed. This process appears to have distinct advantages over previously proposed manganese recovery processes, and, in sharp contrast to leaching procedures, it is applicable to practically any manganese-bearing material.

Jan 1, 1967

By Richard Mainiero

In any construction project involving explosives, care must be taken to protect workers from carbon monoxide (CO) generated by blasting operations. CO is an odorless, colorless gas that can cause illness and death by asphyxiation. In general, the first symptoms include headache, fatigue and lightheadedness. At higher exposures to CO, skin flushing, rapid heart rate, and lowered blood pressure occur. At ever, higher exposure levels, decreased attention span is followed by nausea, vomiting, unpaired coordination, fainting, coma, convulsions and, finally, death. The detonation of explosives in blasting operations generates a range of toxic fumes, but CO is the most insidious because it is colorless, odor less, and is long lasting, since it is not readily removed try reaction with ground water, soil or rock. Additionally CO is generated in relatively large quantities compared to other toxic: fumes. CO may continue to seep out of blasted material long after the odor commonly associated with detonated explosives has dissipated. It is never safe to assume as confined space in the vicinity of a blast is clear of toxic fumes. CO may be present even if the area looks Clear and many hours have passed since the last blast.

Jan 1, 2000

By Thomas Fraser

IN a Nation-wide appraisal of coking-coal reserves and of the feasibility of expanding them by upgrading marginal coals, it is natural that the Pittsburgh region of Pennsylvania should be considered first. Here, where the American iron and steel industry started, the Pittsburgh coal bed is of paramount importance. The use of coke in iron blast furnaces is said to have begun with the discovery that good blast-furnace fuel could readily be made by a simple method of coking Pittsburgh coal. To the present time, the prosperity of the steel industry has depended largely on utilization of this great coal reserve and the cheap transportation afforded by the Monongahela River system. OBJECT AND SCOPE OF INVESTIGATION The initial project in the study of upgrading marginal coking coals was laid out in this area, which contains large reserves of Pittsburgh coal contiguous to the Monongahela and its navigable tributaries. Much of the Pittsburgh coal remaining here is known to have a high sulfur content. The problem of reducing the sulfur to meet metallurgical requirements already has received much attention, and it is considered to be one of the most difficult technologic problems in the field of coal washing.

Jan 1, 1950

By F. J. Wiebelt

Production of small tonnages of asbestos has been reported from 18 California counties; 16 additional counties have occurrences of asbestos. The counties in the northern part of California that have had a recorded production are: Alameda, Amador, Calaveras, Contra Costa, E1 Dorado, Napa, Nevada, Placer, Shasta, Siskiyou, Trinity, and Tuolumne. No deposit in the State has maintained consistent production. Serpentinized peridotites (potential chrysotile-bearing rocks) are widely distributed in the coast ranges, Klamath Mountains, and western foothills of the Sierra Nevada.

Jan 1, 1958

By B. L. Razzaboni, P. Bolsaitis

"The formation of reactive oxygen species resulting from the interaction of silica dust particles with red blood cell membranes was investigated; particularly, the effect of surface hydroxyl (silanol) group concentration on the rate of formation of such reactive oxygen species was investigated. The rate of formation was measured indirectly through the effect of catalase, a hemoprotein peroxidase, on silica-induced hemolysis. It was found that the addition of exogenous catalase to erythrocytes markedly reduces the hemolysis caused by silica particles. Furthermore, the amount of catalase required for deactivation of silica per unit area of particle surface is lower for fumed silica particles and calcined crystalline particles than for uncalcined, crystalline silica, suggesting a correlation between the concentration of OH groups at the silica particle surface and its potential for generation of H2O 2• The addition of albumin, a copper chelator, also decreases hemolysis. These results suggest that the hemolysis caused by silica particles is at least partly related to the formation of H2O2 at the particle surface and its subsequent reaction with Cu+ ions. The relationship between the concentration of surface silanol groups on the silica surface and the amount of catalase required to decrease hemolysis may also provide a method for testing potential fibrogenicity of respirable dusts. IntroductionReactive hydroxyl groups on silica surfaces are known to be cytotoxic and are believed to play a major role in silicosis (1-9). It has been proposed that this cytotoxicity results from hydrogen bonding to cell membranes and a resulting increase in membrane fluidity and permeability (4). Surface hydroxyl groups on silica surfaces have also been shown to interact with carbonyl oxygens in cell membranes (1,5). An extensive study by Nolan et al. (6) of the relationship between the negative surface charge resulting from ionized silanol groups and the hemolytic activity of crystalline a-quartz (Min-U-Sil) has shown a positive correlation between hemolytic activity and the surface concentration of silanol groups. These authors demonstrated that the hydrogen bonding of polyvinyl-N-oxide (PVPNO) with silanol groups, as well as the bonding of metal cations to the ionized sm- groups, results in significant decreases in hemolytic activity. Furthermore, it has been found that the complete removal of surface hydroxyl groups from the surface of respirable silica particles nearly eliminates the hemolytic potential of silica (7), suggesting that hydroxyl groups might be involved in other cytotoxic processes associated with silica-induced lung injury. Reactive oxygen species have been .implicated in cellular damage caused by respirable silica particles. Evidence for the presence .of oxygen radical species (02, OH°, H2O2) generated by silica, especially on freshly formed surfaces, has been produced by various investigators. Kalbanev et al. (8) detected H2O 2 in aqueous suspensions of quartz. Electron spin resonance and spin trapping by Shi et al. (9) confirmed the presence of OH"" radicals in aqueous suspensions of quartz, and Gulumian and van Wyk (10) suggested that both glass and quartz produce hydroxyl radicals in the presence of H2O 2 • Gabor et al. (11) detected the presence of malondialdehydereactive lipid peroxides (i.e., lipid-0°) in cultures of macrophages and respirable silica particles using the thiobarbituric acid (TBA) reaction test. Will (12), however, reported that iron enhances the TBA value of peroxidized lipids, and Scheulen and Kappus (19) found that catalase augmented malondialdehyde formation, thereby increasing the TBA values."

Jan 1, 1990

By Michael Schmitz, John A. Organiscak

ABSTRACT: A method (patent pending) has been developed to determine the quality of environmental cab filtration systems. This method utilizes specially configured filter cartridges to remove carbon dioxide from the ambient air with the environmental cab’s air filtration system. A real-time gas monitor is placed inside an unoccupied cab with the filtration system running to time decay the carbon dioxide to its lowest concentration or equilibrium level. The outside carbon dioxide concentration level can be measured concurrently with another gas monitor or with the same inside cab gas monitor during a representative period before and after the inside sampling is conducted. Cab filtration system leakage is comparatively deduced from the difference between the special cartridge filter efficiency and overall cab efficiency. Laboratory trials have illustrated that desirable high efficiency test filter configurations (greater than 99 % efficiency) can be devised, but have air quantity and test time limitations. These trials also demonstrated that CO2 penetration was reflective of controlled air leaks around a high efficiency filter under equilibrium conditions. This report examines the elements of this patent pending method.

By W. T. Millar

Field reconnaissance and laboratory tests an clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By Avery H. Reed

RECORD production of cement, clays, salt, sand and gravel, and stone highlighted the mineral industry of the State in 1956. Coal and iron-ore production declined owing to increased imports of foreign iron ore and decreased demand for metallurgical coke. Alabama ranked second in production of bauxite and of native asphalt, and third in output of iron ore. New developments in the State included the Citronelle oilfield and its 97 wells, which more than doubled the total production of petroleum compared with 1955. There is no question about the impetus that field has given to the oil and gas industry in Alabama, now 13 years old. The State's 4 oilfields are in southwest Alabama and its 1 gasfield is in Marion County, in the Warrior coal basin.

Jan 1, 1958

By K. E. Soroka

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,0000 C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first held field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fifth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 1, 3, 4, and 5.) Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and this part (part 5) describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water-injection-fume exhaustion quenching procedure are planned.

Jan 1, 1986

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Ch. D. Taylor

Past studies with blowing face ventilation systems have shown that using a machine-mounted scrubber and water sprays can reduced methane levels at the face. The current research was conducted to determine how the sprays and scrubber interact to reduce methane levels, and what spray configurations provide the best face ventilation when used with a scrubber. Testing was conducted in a ventilation test gallery designed to simulate a full-scale mine entry. In the entry, a model mining machine, equipped with a simulated dust scrubber and water spray systems, was located at the face of a 6.1 m (20 ft) box cut. Face ventilation was provided by a blowing curtain located 12.2 m (40 ft) from the face. Methane released from a manifold at the face was measured at six locations near the face to compare the ventilation effectiveness of the spray systems while operating with and without the scrubber. Airflow movement across the face was affected by the spray configuration and scrubber operation. Average face concentrations were lowest when directed sprays were used with the scrubber. Varying the direction of the scrubber exhaust affected face methane levels.

By H. Herbert Hughes

Soapstone commonly is associated with talc , and reports on either commodity usually contain a discussion of the other . From a geological or mineralogical standpoint the combination is justifiable , for soapstone essentially is impure talc . Commercially , however , the relation between them is remote . About 95 per cent of all talc sold in the United States is in ground form, whereas practically all soapstone is sold as furnace blocks or as fabricated structural slabs for many and diverse applications .

Feb 1, 1932

By Manuel Gomez

Primary, low-temperature tars are generally known to alter with time. The effect is believed to occur, in some instances, without the external influence of air, light, or heat. Since one of the processes occurring during extended storage is oxidation, the action of mild oxidation induced by air and heat, in addition to the effect of storage, was studied. The principal effect in aging and oxidation is formation of pitch at the expense of the distillate fraction. The fraction boiling above 270° C. is mainly involved in pitch formation due to storage, whereas all fractions are affected to some degree when tar is heated at 125° C. in the presence of air. If the effects of air are considered, the aromatic and tar-acid fractions seem to be important in pitch formation.

Jan 1, 1956

By A. L. Engel

This report is a compilation of the results of preliminary tests on ores containing scheelite (calcium tungstate). In most of the ores, scheelite was the only value; but several samples contained other values, such as gold, base metals, or, in one instance beryl. These investigations were made to assist the development of domestic tungsten resources by establishing satisfactory treatment methods suitable for small-scale operations. The samples were obtained through the Mining Division of the Bureau of Mines and represent, for the most part, newly discovered deposits. A previous report2/ discussed laboratory test procedures. A less detailed description of test procedures is included in the present report. As is usual in an investigation of this type, only a limited amount of work was done on most of the samples to indicate the results that could be expected from simple treatment of the particular ore. The occurrence of scheelite and the texture of the minerals present differ greatly in individual ores and must be determined and considered in establishing such details of treatment as grinding to obtain optimum liberation of the minerals, the preferred type of gravity concentration, or possible further treatment by flotation.

Jan 1, 1954

By W. R. Reed, G. J. Joy

The personal dust monitor (PDM) is a new coal mine respirable dust sampling instrument that has the ability to provide accurate end-of-shift and real-time respirable dust exposure data. A hypothetical cost comparison analysis of the PDM with the current MSHA-required coal mine dust personal sampling unit (CMDPSU) was conducted. Some simplifying assumptions were made to create hypothetical cases for analysis. This analysis was limited to respirable dust sampling of one designated operator (DO) and one designated area (DA) for one mechanized mining unit (MMU) which operated one shift per day. Only sampling intervals of the minimum sampling as required by federal regulations and continuous sampling were analyzed. This cost analysis from the company perspective is only one part of an overall cost/benefit analysis that should be conducted at a later date. In this analysis, company-associated costs were examined for both sampling systems. Results show that the PDM, while it has high initial costs of approximately $12,600, may be a cost-effective sampling system for measuring coal mine respirable dust. The estimated present worth cost of conducting the minimum required dust sampling over a five-year life ranges from $5,850 to $19,000 for the CMDPSU, with the higher present worth cost including costs of potential violations incurred. For the PDM, the comparable present worth cost is $14,900 to $19,300, with the lower present worth cost representing a lower capital cost of $8,150 per unit if more than 850 units are produced per year, while the higher present worth cost reflects the result with the higher $12,600 capital cost.