Search Documents

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By Ralph P. Carter

It is apparent that coal will play an increasingly important role in satisfying the nation's energy requirements for the remainder of this century. Both deep mining and surface mining will be practiced to develop known U.S. coal reserves, but until significant improvements in the productivity of deep mining emerge, surface mining is likely to be predominant. This report addresses the problems of coal extraction and surface mine reclamation in the 11-state Midwestern coal resource region, where surface stripping of high-sulfur, bituminous coal has been a well-developed industry for most of this century. Midwestern coal markets have declined in recent years. In part this is a result of widespread conversions to more convenient and (apparently) economical liquid and gaseous fuels, but the decline in Midwestern coal use is also attributable to the impact of current air pollution control regulations that prohibit emissions of sulfur oxides and particulate matter. A part of the regional demand for Midwestern coal has been transferred to the Northern Great Plains where extensive low-sulfur coal reserves are currently being developed.

Jan 1, 1974

By R. Karl Zipf, Z. T. Bieniawski

"SummaryAs part of an effort.to understand the mechanics of fine fragment formation in coal, which is important in studies of respirable dust due to mining, fracture toughness measurements and the strain energy density (SEO) theory were applied to calculate the crush zone size under a cutting tool in coal. This · zone is the major source of fine fragments in the 1 to 10 µm size range. The model used in these calculations is a boundary element program containing a failure criterion based on the SEO theory. The boundary element program calculates linear elastic stresses at numerous points in the coal material ahead of a cutting bit. These stresses arc then input to a subroutine called critical ftaw length and orientation (CFLO) which uses the SED theory to determine the CFLO for a small crack at the boundary element stress computation point. The extent of crushing is based on earlier postulates about . the role of inherent flaws in a fragmentation process. To form 1 to 10 µm fragments requires firstly a local stress strong enough to activate flaws with a characteristic length less than 1 to 10 µm and secondly, a flaw density sufficient to provide an average spacing between flaws also on the order of 1 to 10 µm. The locus of active lO µm ftaws represents the maximum possible extent of fine fragmentation in the 10 µm or less size range assuming that a sufficient inherent flaw density exists. The approach offers a first order approximation to the extent of crushing under a tool tip. The size and shape of the crush zone volume is affected by the attack angle and geometry of the tool.IntroductionFine fragment generation in the 1 to 10 µm size range under the action of a generic coal cutting tool may be explained on the basis of fracture mechanics which suggests two major sources of fine fragments: first in a crush zone near the tool tip and second by shear fracturing. along major macrocrack surfaces (Zipf and Bieniawski, 1988a). In this paper, fracture toughness measurements and the strain energy density theory are used to calculate the crush zone size. This zone represents the major source of fine fragments in the 1 to 10 µm size range and understanding the mechanical factors controlling its size represents a first step toward using fracture mechanics to characterize the ·tendency of various coals to produce undesirable fine fragments."

Aug 31, 1989

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steel in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steel as impurities. For example, silicon additions form SiO2 or combinations of SiO2 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MnO, SiO2, and Al2O3, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods. The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

The results of a Feasibility and Design Study of Surface Impregnation Equipment to be used for Chemical Stabilization of Coal Mine Structures are described in this report. The study was sponsored by the United States Department of the Interior, Bureau of Mines, under Contract H0210055. This program was undertaken as an essential part of the Bureau of Mines Chemical Ground Stabilization Program. The responsible prime contractor was The Eimco Tunneling and Mining Machinery Division of the Envirotech Corporation. The Rocketdyne Division of the North American Rockwell Corporation performed part of the feasibility study and design and testing of the metering and feed system as a subcontractor to Eimco.

Jan 1, 1972

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992

By Frank D. Lamb

Pyrophyllite, a hydrous aluminum silicate (Al2 Si4O10 (OH)2 ) has been mined in North Carolina and marketed without beneficiation for the past 100 years, but recent demands for higher-grade material indicate that an economical concentration method is needed for at least a part of the pyrophyllite production. Past production has depended upon selective mining and hand sorting, which is often unsatisfactory because of the finely disseminated character of the ores. The major impurity in North Carolina pyrophyllite ores is quartz, which accounts for the abrasiveness of the commercial product. Since pyrophyllite is only slightly heavier than quartz, those ores cannot be beneficiated by simple gravity-concentration methods. Some separation can be attained by differential grinding and air classification because of the difference in hardness of the two minerals) but the separation is not sharp. Froth flotation of pyrophyllite from Quartz has never been attempted commercially, but if the demand for high-grade material is sufficient, it would seem that this process offers the most premise of being economically feasible.

Jan 1, 1950

By Raja V. Ramani, Robert L. Frantz

"The House/Senate Joint Conference Committee has instructed the Bureau of Mines to have the Advisory Committee on Mining and Mineral Resources Research review on an annual and simultaneous basis each generic mineral technology research center (GMTC). In order to accomplish that review promptly and uniformly, committee members have revised and approved an in-depth questionnaire. That document formed the basis of their review. The information provided by that questionnaire was an important factor in their recommendations concerning the future direction of the program; a presentation was made at the last National Plan Update.The comprehensive nature of the questionnaire and the scope of the information contained therein make it an excellent retrospective of the Center. Having a clear vision of where the Center has been and knowing where it is now will help guide it into the future. It is felt that such a detailed view of the Center's facilities and research program will be of value to Center personnel and Advisory Committee members.Each aspect of the questionnaire has been examined, answered in detail, and documented throughly. With the completed questionnaire as a guide, this volume examines the research program, Center personnel presently active on GMTC projects, number of graduate degrees granted with GMTC support, GMTC publications, degree of individual interaction, technology transfer, the reference center, GMTC equipment and facilities, and any envisioned plans for future research. It is hoped that this volume will serve as a review of the years 1984-1988, the first four years of the Center's operation."

Aug 31, 1989

By W. R. Gilliland, G. W. Jones

"One-phase of the accident prevention program of the Bureau of Mines is the determination of the explosion hazards of various combustible gases and vapors encountered,mining and allied industries and the development of means and methods of eliminating them.Gasoline is foremost among the combustible-liquid's as to quantity used and variety of applications in industry, It is a chief contributor to the causes of fires and explosions, taking an enormous yearly toll in property damage and considerable loss of lives.The results presented in this report evaluate the effect of various gaseous inert substances, which owing to their chemical composition, should be of considerable value in the prevention of gasoline fires and explosions. The substances investigated are as follows: Nitrogen (N2), automobile exhaust gas (85 percent N2 + 15 percent CO2), carbon dioxide(CO2), dichlorodifluoromethane (CCl2F2-Freon-12), trichloremenofluoromethane (CC13F-Freon-11), and dichloromonofluoromethane (CHCl2F-Freon-21).The general term ""gasoline"" designates a combustible liquid of such characteristics as to give satisfactory operation without preheating in spark-ignition-type internal-combustion engine. It comprises a complex hydrocarbon mixture having a limiting distillation range and produced commercially by distilling or ""cracking"" crude petroleum or other various petroleum stocks. Small proportions of other substances may be incorporated in the gasoline to enhance its antiknock properties or operating characteristics in internal-combustion engines and to increase its stability during storage, transportation, and use.It is thus seen that gasoline may have rather wide variations of chemical and physical properties, and it would: appear that the results of any investigation dealing with one particular gasoline might not be applicable to other types. However, as indicated by the results given in this report, the inflammable properties of different gasolines at normal atmospheric temperatures are influenced largely the mars volatile hydrocarbons containing 5, 6, 7 carbon atoms- in the molecule, and that the heavier constituent of higher molecular weight have a minor influence on the inflammable properties at ordinary temperatures."

Apr 1, 1946

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By Jr. Jacobson

Thermal reactions of l-methylpyrrole, l-butylpyrrole, and l-isopropyl-pyrrole were investigated by a flow method in the temperature range of 4500 to 5750 C. Those of I-butylpyrrole and l-isopropylpyrrole were also investigated in the 3400 to 4000 C range in a static system. The I-substituted pyrroles isomerize by an irreversible reaction to 2-substituted pyrroles. A reversible isomerization reaction shifted the alkyl group from the 2-to the 3-position on the pyrrole ring. All of the isomerization reactions are homogeneous, unimolecular, nonchain, first-order reactions having similar mechanisms and transition states. There is decomposition and cleavage of the longer alkyl side chain when it is in either the 2-or 3-position giving, as products, pyrrole, 2-and 3-methylpyrrole, 2-and 3-ethylpyrrole, pyridines, and hydrocarbons. The decomposition reactions appear to be by free-radical mechanisms. Pyridine homologs are formed by the expansion of the alkylpyrrole: butylpyrrole produces pyridine, and isopropylpyrrole produces 3-methylpyridine. Approximate Arrhenius equations are given for the formation of the decomposition products.

Jan 1, 1966

By Fred D. DeVaney

The Mesabi iron district of Minnesota has a potential production of over 50 million tons of iron are annually. The large shipments of ore each year are gradually depleting the reserves, and if the present rate of production is to be maintained there must be a growth in the present available ore supply. Growth is a natural course. The growth of a city may be affected by the addition of city blocks or by the improvement of utilities necessary for its betterment. These may go on in the order named or concurrently. The city-block type of growth of the Mesabi has been tremendous, and the "betterment" type has followed in due course. Probably the former has reached its limit, and if so, more time will be allotted to the latter. It is not the in¬tent of this paper to present either a eulogy of the wonderful mining methods or a history of the milling, but it is pertinent to say that if the lean-ore area continues to produce, the continuance will be more the result of further improvement of milling methods non well under way than of extension of boundaries by the city block plan of growth.

Jan 1, 1932

REFERENCES AND FOOTNOTES 1. U.S. Department of the Interior, Office of Surface Mining. Surface Coal Mining Reclamation: 10 Years of Progress: 1977-1987. Washington, D.C. August 3, 1987.48 pp. (For sale by the Superintendent of Documents, U. S. Government Printing Office, Washington D.C. 20402.) 2. The Rural Abandoned Mine Program (RAMP), authorized by Section 406 of SMCRA, provides for the control and prevention o f erosion and sediment damages from unreclaimed abandoned mine lands. 3. The Small Operator Assistance Program (SOAP), authorized by Section 401(b)(1) and 507(c) of SMCRA authorizes up to 10 percent of the fees collected for the Abandoned Mine Reclamation Fund to be used for technical assistance to help qualified small mine operators obtain techincal data needed for permit applications. Operators who produce fewer than 300,000 tons of coal per year are eligible for assistance. 4. OSM regulations 30 CFR 816.42 and 817.42 require water from areas distrubed by mining activities be in compliance with all applicable state and federal water-quality laws and effluent limitations for coal mining established by the U.S. Environmental Protection Agency. 5. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 6. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 7. Source: OSM Field Office Annual Reports. 8. Johnson, W. and G.C. Miller, Abandoned Coal-Mine Lands: nature, extent, and cost of reclamation. U. S. Bureau of Mines, 1979,29 pp. PHOTOGRAPHIC CREDITS Front cover, pp. i, 1, 2 bottom, 7 right, 10 bottom left, l 1 top, l l bottom right, 12 top, 13 bottom, 14 bottom right, 15,16 bottom, 17 top, 17 bottom right, 18 bottom, 19, 20 bottom, 21 top, 22, 23, 24 bottom, 25 bottom, 26 bottom left, 26 bottom right, 27, 28, 29 top, 30 bottom, 32 bottom right, 33 top, 34 top, 35 top left, 35 bottom left, 35 bottom right, 36 top, 37, top right, 37 bottom, 38 bottom, 39, 41, 42 top, 43 bottom, 44 bottom left, 44 bottom right, 45, 46, 47, and 53: Chuck Meyers, OSM. Page 2 top and center: Tony Fuhs. Page 3: John Sharkowicz, OSM. Page 6 left: North American Coal Corp. Pages 6 right, 7 left, l l bottom left, 13 top left, 13 top right, 17 bottom left, 21 bottom, 25 top left, 25 top right, 29 bottom, 30 center, 32 top, 32 bottom left, and 38 top: Bob Welch, OSM. Page 10 top left: Donald Stump, OSM. Pages 10 right, 14 top right, 14 center right, 18 top, and 44 top: Ron Hill, EPA. Page 12 bottom: Texas Utilities Co. Pages 16 top, 20 top, 24 top: Tennessee Valley Authority. Page 26 top right and 26 center left: Richard Dick, U.S. Bureau of Mines. Pages 30 top, 33 bottom left, 33 bottom right, 35 top right, 36 bottom, 37 top left, 40 top, 40 bottom, 42 bottom, 43 top left, and 43 top right: Jim Boyer, OSM. Page 31 top left, and 31 top right: Bruce Wage, Western Energy Co. Page 31 bottom: Rex Wilson, OSM. Page 34 bottom: West Virginia Division of Abandoned Mine Lands. Page 35 center: William Weist, Jr., OSM.

Jan 1, 1992

By John C. Machisak

INJURY DATA and experience at, coal mines in the United States for 1953 and 1954 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding tables for 1953 and 1954 follow in consecutive order under the following general sections: (A) General injury experience: Tables 1 to 11: Contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity and time-loss rates. (B) Selected injury data: Tables 12 to 85: Contain current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines.

Jan 1, 1958

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By F. E. Block

The reaction between calcined dolomite and ferrosilicon has been studies with the aim of developing a continuous process for magnesium production. Small-scale tests were made in vacuum retorts similar to those used in the vacuum retort process as developed by Pidgeon (1)2/ and operated during the period of World War II in several Government-owned plants. Factors investigated with respect to the silicon efficiency were the reaction temperature, reaction time, amount of excess dolomite in the charge, and effect of adding sodium silicate to the charge to serve as a binder. Additional laboratory tests were made to study the reaction at elevated temperature but at atmospheric pressure. Silicon efficiencies exceeding 80 percent were found to result when operating in the temperature range from 1,750° to 1,800° C. for periods of 20 to 30 minutes.

Jan 1, 1956

By L. B. Berger, W. P. Yant, J. B. Littlefield

"INTRODUCTION Hydrogen sulphide (H2S) is one of the most toxic industrial gases and of relatively wide occurrence in industry. Among its common industrial occurrences are, in the production and refining of high-sulphur petroleum, in natural gases, in gypsum and sulphur mining, in rock strata and underground waters (where it is encountered in tunneling and caisson work) in blasting with black powder and in blasting high-sulphide ores with other explosives, in gas manufacture, in the carbonization of coal, and in the manufacture of chemicals.The usual methods of detection, other than by the sense of smell, which is lost in 2 to 15 minutes' exposure to 0.010. to 0.015 percent of this gas, 5/ either are too cumbersome for frequent and rapid analyses or, like the wet lead acetate paper test, afford only qualitative results. A qaantitative determination usually involves the use of solutions, bubblers, flowmeters, standard solutions, burettes, and indicators manipulated by trained technical men. All apparatus and methods in common laboratory use are, in general, unsuitable for the field.The physiological response attending exposure to various Concentrations of hydrogen sulphide in air, is as follows, in percent by volume 6/:0.005 to 0.010: Subacute poisoning - slight symptoms, such as mild conjunctivitis and respiratory-tract irritation after 1-hour exposure."

Jun 1, 1935

By Irving Kabik

Chlorates and perchlorates, when mixed with certain reducing materials, may give a detonating explosive of considerable power. Concerning explosive chlorate mixtures, Guttman3/ states that they "have at all times fascinated inventors on account of the large amount of oxygen stored up in potassium chlorate, which can be given off so readily. When Lavoiser and Berthollet tried to make a chlorate powder in a stamp mill in 1788, they made a great show of it, and even two ladies were present. Unfortunately, after a certain amount of pounding the powder exploded and killed an official and the daughter of the Government commissary, who assisted at the experiments.***. It is interesting to observe how the same old mixtures are proposed over and over again with slight alterations only, in order to qualify for a patent. Potassium chlorate with some carbonaceous matter like charcoal, sugar, starch, glycerin, flour, or sometimes a vegetable or mineral oil and the like occurs again and again." Sprengel explosives, in which some of the undesirable sensitivity of the chlorate was minimized by coating the crystals with a liquid reducing agent, received some attention after a patent was issued to Dr. Herman Sprengel in England in 1871.4/ A somewhat similar explosive, known as Rack-a-

Jan 1, 1945