Search Documents

By T. E. Sterner

A laboratory investigation was conducted to determine the applicability of the thermal oil-recovery method as a means of increasing ultimate oil recovery in the Appalachian region. The primary objective was to establish self-sustained combustion in consolidated and unconsolidated sand test assemblies saturated with various amounts of Pennsylvania Grade crude oil and synthetic brine. Tests using blocks of sandstone were unsuccessful because of sealing problems and fracturing of the rock due to thermal stresses. A combustion wave of about 700° F was propagated through the sand-oil-water packs in the linear tube tests. The high air flux used resulted in high oil consumption and rapid movement of the combustion wave through the tubes. Analytical tests on the sand pack showed that sufficient fuel was deposited during the linear tube experiments for a self-sustained combustion wave.

Jan 1, 1967

By William C. Cooley

A review was made of two Russian books and a chapter from a third book dealing with pipeline transport of coal. Emphasis was placed on hydrotransport of coarse coal in underground mines or surface pipelines. The books reviewed were: "Means of Increasing the Effectiveness of Hydrotransport," by V. N. Pokrovskaya (1972), "Parameters and Modes of Hydraulic Transport of Coal" by V. V. Traynis (1970), and the chapter "Calculations of Hydrotransport of Useful Minerals and Waste Rock" from the book "Hydromechanization of Opencast Workings" by G. A. Nurok (1970). All three are unique and useful additions to the world literature on hydrotransport. The Traynis book reveals the development and results of circular wheel stand tests to simulate hydrotransport in horizontal pipes, which is a potentially outstanding contribution to slurry pipeline technology. Graphical data and equations are presented which suggest that headlosses for coarse coal can be predicted with good accuracy for pipe sizes up to 14 inches in diameter. Wheel stands permit tests for pipe wear and lump degradation without recycling coal through pumps. Recommendations are made for wheel stand tests and for correlation of existing data.

Jan 1, 1976

By Michael M. Hamilton

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 37,542-acre portion of the 57,002-acre Riordan?s Well Wilderness Study Area (NV-040-166) in order to evaluate its mineral resources. The area studied is located in Nye County, NV, about 60 miles southwest of Ely, NV. Subeconomic mineral resources of limestone and sand and gravel were identified in the study area. The Troy and Irwin mining districts, 4 miles to the west, were active between 1868 and 1963, producing small amounts of gold, silver, lead, and tungsten from mines well outside the study area. Except for minor prospecting activity, most mining activity in the study area has been since 1980, consisting of claim locations and geochemical surveys.

Jan 1, 1987

By A. L. Engel

In the period of 1942-1945, medium-grade, oxidized, lead-silver ore was mined and shipped from the Diamond district near Eureka, Nev. An encouraging tonnage of low-grade ore was developed during these operations and partly blocked-out for future mining. If the low-grade ore could be treated profitably, further development of the district would result, and production of an important strategic metal might be increased. A representative sample of Diamond district ore was obtained through the Reno office of the Mining Division for the studies described in this report. The sample consisted of lumps and fines of a highly altered siliceous rock containing much earthy red hematite and some granular black hematite. Examination with the binocular microscope showed the lead carbonate mineral, cerussite, in seams and disseminated in the hematite. No zinc or silver minerals were identified, and no sulfide minerals were present. Analyses of the ore showed:

Jan 1, 1951

By Jeffrey S. Newman

This report establishes a methodology for the evaluation of gas detection devices and is the result of a critical investigation into the basic principles defining gas detector performance. A scheme is presented to evaluate the performance of a test sample of gas detectors based on the detector type and intended application. Test procedures, worksheets, test apparatus, glossary and statistical methods for handling test data arc given. In addition, evaluation standards and test parameters are identified. It is intended that this report serve as a comprehensive framework for the eventual certification of all gas detectors for mine applications. A plan is proposed and recommended for the quantification and implementation of evaluation standards for gas detection device certification.

Jan 1, 1980

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

By Carlton E. Brown

Inquiries and instructional work on the determination of the number concentration of dust in atmospheres known or suspected to contain pneumoconiosis (silicosis and asbestosis) - producing particulate matter indicate a need for a description of the impinger method used by the Bureau of Mines. The impinger method consists of the collection of dust in a liquid medium and the counting under the microscope of the particles in a known portion of this liquid. The dust-collecting device is called an impinger. The dust in the air drawn through this collector at a known rate impinges at high velocity upon a smooth surface under a bubbling column of liquid. The dust is either picked up from this surface by the liquid or removed from the air as it passes through the liquid.

Jan 1, 1938

By R. Carson Dalzell

The use of nuclear fission for chemical process heat offers the special advantage of high temperature, limited only by materials of construction. The process heat may be supplied economically at elevated pressures, since no compression of combustion air is required. For the initial effort in developing a high-temperature reactor, the indirect cycle, using helium as the heat-transfer medium, was chosen. The major problems are the design of high-temperature fuel elements, construction of an exchanger to transfer heat to process streams in the range of 2,500° F., and development of compressors capable of recycling helium at 1,000° F. and above. A conceptual design of a nuclear reactor to furnish process heat for coal gasification has been made. Spherical fuel elements utilizing a graphite structure, impregnated with uranium carbide fuel, were chosen, as spheres offer the possibility of easier loading and unloading of the reactor. Calculations of pressure drop and gas-pumping power for the system are included.

Jan 1, 1959

By Fred N. Kissell, Jay F. Colinet

The two major lung diseases of miners are "blacklung" and silicosis. Blacklung, or pneumoconiosis, was first recognized as a disease of British coal miners in the 1600s. However, investigations into the cause of blacklung disease did not begin until the 1900s. The causative agent of pneumoconiosis in coal miners was thought to be silica until studies in the United Kingdom provided evidence that expo- sure to coal dust containing minimal silica could also cause pneumoconiosis. In the Federal Coal Mine Health and Safety Act of 1969, coal workers pneumoconiosis (CWP) was defined as "a chronic dust disease of the lung arising out of employment in an underground coal mine." Diagnosis of CWP is generally based on chest x-ray findings and a patient's history of working in coal mines, usually for 10 or more years. In its early stages, CWP is called "simple CWP." Miners with simple CWP are at increased risk of developing an advanced stage of the disease, called "progressive massive fibrosis" pMF) or "complicated CWP." PMF (complicated CWP) is associated with significant decreases in lung function and oxygen- diffusing capacity. PMF is also associated with breathlessness, chronic bronchitis, recurrent chest illness, and episodes of heart failure. Coal miners with silicotic lesions or PMF have an increased risk of tuberculosis and other mycobacterial infections. PMF may progress even in the absence of further dust exposure. This disease is also associated with increased mortality (National Institute of Occupational Safety and Health [NIOSH] 1995). The most recent study to determine the prevalence of CWP in coal workers was in the mid- 1990s. The average prevalence of CWP was 2.8%, but for those with 30 or more years in the industry it was 14%. For the 10-year period from 1987 to 1996, 18,245 deaths were attributed to CWP. The most frequently recorded occupation on the death certificate (70%) was mining machine operator (NIOSH 1999). Silicosis may develop when inhaled respirable crystalline silica (quartz) is deposited in the lungs. The clinical diagnosis of silicosis is based on (1) recognition by the physician that the level of silica exposure is adequate to cause the disease, (2) the presence of chest radiographic abnormalities consistent with silicosis, and (3) the absence of other illnesses (e.g., tuberculosis or pulmonary fungal infection) that may mimic silicosis. The radiographic patterns are often the same for CWP and silicosis; thus, these diseases are sometimes distinguishable only by work history or pathological examination. Chronic silicosis commonly involves 15 or more years of exposure to silica. The characteristic microscopic feature is the silicotic nodule. Chronic silicosis is often asymptomatic and may manifest itself as a radiographic abnormality with small, rounded opacities of less than 10 mm in diameter, predominantly in the upper lobes. Lung function may be normal or show mild restriction. Chronic silicosis is also associated with a predisposition to tuberculosis and other mycobacterial infections and with progression to complicated silicosis.

By R. V. Ramani, S. Shankar

"Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant (Shankar and Ramani, 1991 ). Therefore, as part of the Respirable Dust Center's ongoing research, the following three-part study was undertaken:• a study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities;• a study of the same in the Lake Lynn Laboratory Mine of the USBM with both air flow and walking by personnel causing re-entrainment; and• the mathematical modeling and computer simulation of the re-entrainment phenomenon.In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory mine are presented. Comparing the results from the two studies,it was observed that increasing the air velocity increased the rate of re-entrainment ( Shankar and Ramani, I 994a) and the rate of re-entrainment decreased with the time of exposure of the source dust to the flowing air. In addition, when the source dust was composed of particles of different sizes, the airborne dust concentrations due to re-entrainment were higher than when the source dust was composed of particles of the same size. The contribution of airborne dust concentration due to air flow was negligible compared to the contribution due to walking. IntroductionIn underground coal mines, dust is produced primarily during the process of mining and during such activities as pillar spall, loading, belt transfer and roof fall. The generated dust is entrained and then collects on surfaces through dispersion, diffusion and eventual deposition. Removal forces, such as flowing ventilation air or turbulence caused by walking and moving vehicles, can re-entrain the deposited dust (Hall, 1955). A portion of the re-entrained dust remains airborne and increases the concentration of airborne dust in mine airways.The presence of airborne coal dust in mine airways in large concentrations can be hazardous. Health effects include coal workers' pneumoconiosis (CWP) and silicosis, and it can be a nuisance affecting visibility. In addition, as is common during methane explosions, if the concentration of airborne coal dust becomes significant, there could be a coal-dust explosion (Singer, Cook and Grumer, 1972; Singer, Harris and Grumer, 1974; Edwards and Ford, 1988). Through concerned research efforts over the last decade, significantprogress has been made in reducing the airborne dust concentration in mine atmospheres. However, secondary sources, such as re-entrainment, have not been studied in-depth. It is important to understand the phenomenon of re-entrainment and its potential contribution to the airborne dust concentration in mine airways for further decreasing airborne dust hazards in mines."

Dec 1, 1996

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the C2 through C5 paraffins, the C2 and C3 olefins and possibly the C4 and C5 olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pct of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

By John P. McDonnell

This U.S. Bureau of Mines report describes the results from an in-mine investigation of an alternative longwall gate road design. The coal mine operator modified the pillar layout (reversed the location of the big and small pillars) in a portion of a three-entry longwall gate road area. The modified pillar layout was an attempt to reduce stress and, subsequently, stress-related ground control problems (cutter roof and dynamic floor heave events) in the tailgate region during "second-panel" mining. The results from borehole pressure cells installed in the modified gate road area showed that the ground pressures in the panel edge and adjacent small pillar were significantly reduced during second-panel mining compared with ground pressures experienced in the typical pillar layout gate road areas. The reduced stress levels around the tailgate entry adjacent to the second panel, as compared with the tailgate stress levels with the typical pillar arrangement, contributed to improved tailgate ground conditions in the test pillar zone.

Jan 1, 2010

By Ryan G. Wade, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

By F. W. Benn

The Bureau of Mines investigated flotation methods for recovering fluorite and byproducts from two samples of the Fish Creek deposit in Eureka County, NV. The preferred method for tre.ating a fluorite-beryllium sample included (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, (3) muscovite flotation, (4) silicate flotation, (5) sodium hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concen-trate. Laboratory results showed that over 94 pct of the fluorite was recovered in a recleaner concentrate containing 98 pct CaF2, Beryllium flotation produced concentrates containing in excess of 5 pct BeO with recoveries over 70 pet. The preferred method used for a fluorite-mica sample consisted of (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, and (3) mica flotation using an anionic-cationic collector system. Laboratory results showed that 84 pct of the fluorite was recovered in a recleaner concentrate containing 96 pct CaF2, Mica flotation produced a concentrate containing 95 pct mica at 85-pct recovery.

Jan 1, 1986

By R. A. Egen

The purpose of this book is to provide an indication of what good hoisting practice is and how it might be achieved. To this end the book contains discussions of equipment and inspection and maintenance procedures developed and used by mining people in striving for safe, reliable hoisting equipment. Most of this information comes from domestic practice; the rest is foreign, notably from Canada. Most things discussed have long proved their general worth, and others promise to; a few are beginnings. However, nothing is conjectural or theoretical; the practices described herein are in use somewhere in the mining world. The stress is on equipment in use; it is not a design-guidelines manual. Nevertheless, there are some sections dealing with design material since it may be of value in a maintenance/ replacement sense. Mine hoisting installations encompass such a wide variety of equipment and conditions that it is impractical to specifically cover them all. This book mainly treats conventional systems using conventional components with some discussion of the more common unconventional (special) systems in use. There is no recognized definition for a "conventional" mine-hoisting system. Herein the term means those systems most commonly used in daily operations for transporting men, materials, and product-electrically driven drum and friction hoists, with guided conveyances running in vertical or inclined shafts. Beyond this, what "conventional" means is probably best illustrated by the topics discussed.

Jan 1, 1975

By G. H. West, R. L. Sebastian, W. A. Darror

"This bibliography was compiled in the course of research work by the Bureau of Mines on the utilization of magnesites in the West. The results of the research will appear as a bulletin of the Bureau.1. ANALYTICAL METHODS. 11 Knight, X. and Wheeler, W.H. Proc. Iowa Acad. Sci., 13, 1907, 167 (C.A.1, 1370). Describes experience in analysing calcite and dolomite. Reports great excess of oxalate unnecessary and separation of sulphates by alcohol is best.2 Meyerhofer, J. Zeit, Angew. Chem., 21, 1908, 592. Direct determination of Mg as phosphate after removal of SiC2, by keeping R203 in solution with ammonium citrate.3 Merckschen Guano Phosphat Werke. Chem. Ztg., 33, 1909, 545 (C.A. 3, 2281). volumetric analytical methods.4 Popel, M. Zeit. Angew. Chem., 21, 1908. 2082 (C.A, 6, 412). Determination of CaO in presence of CaC03.5 Blasdale, W.C. Jour. Am. Chem. Soc., 31, 1909, 91? (C.A. 3, 2658). Studies of separation of Ca from Mg.6 Hundeshrgen, F. Zeit. Offent. Chem., 15, 1909, 85 (C.A. 3, 1853). Valua¬tion of caustic magnesia by analysis. Volumetric methods.7 Frerichs, H. and Krosberg, W. Apoth. Zeit., 24, 1909. 679 (C.A. 3, 2996). Tecting magnesia alba for Fe.8 Schoorl, N. Zeit. Anal, Chem., 48, 1009, 593 (C.A. 4, 5E9). Microchemical tests for Mg, Li, K. and Na.9 Heyer. Chew. 2Ag., 33, 1009, 1157 (C.A. 4, 1588). Determination of CaO in presence of CaCO3. CaCO3 in soluble in cold neutral solution of NH3 salts. Solubility Is diminished by free NH4OH."

Oct 1, 1923

By J. M. Mutmansky, C. Lee

"IntroductionRecognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries, Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs.To identify the causes of CWP, many research efforts have been made throughout the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous research studies has appeared elsewhere (Mutmansky and Lee, 1984).The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented"

Mar 1, 1989

By Lloyd Carpenter

Eighteen elements were determined spectrochemically in vanadium metal and its compounds in the general range of 1 to 1,000 ppm by means of spark-ignited unidirectional arc excitation. The samples were converted to vanadium pentoxide and combined with a mixture of graphite, lithium carbonate, and gallium oxide. For the molybdenum determination, the oxidized samples were mixed with sodium chloride and packed in copper electrodes. Average precision of the method was 15.6 percent relative standard deviation and relative error was 4.4 percent.

Jan 1, 1963