Search Documents

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By Cavallaro. J. A.

This report presents the results of a washability study of 455 raw coal channel samples with special emphasis on sulfur reduction. These raw coals contained on the average 14.0 percent ash, 1.91 percent pyritic sulfur, and 3.02 percent total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds. Finally a similar statistical evaluation is included showing composited data interpolated at Btu recovery levels of 50, 60, 70, 80, 90, and 100 percent. Graphical summations are presented for the various coal producing regions. Generally, significant sulfur reduction is achieved if the coals are crushed to a finer size and the higher specific gravity increments are removed. If a 50-percent Btu recovery was acceptable, then 32 percent of the samples tested could be upgraded to meet the current Environmental Protection Agency (EPA) standard of 1.2 pounds of S02 emission per million (MM) Btu when crushed to 14-mesh top size and separated gravimetrically.

Jan 1, 1976

By John J. Mulligan

The Bureau of Mines investigated coal deposits at Mount Gran (latitude 76°59' S, longitude 161°07' E), Victoria Land, Antarctica, during the austral summer of 1959-60 as part of the continuing U.S. Antarctic Research Program, which is under the auspices of the National Science Foundation. The coals and associated rocks were measured, sampled, and analyzed. Five coalbeds, ranging in thickness from over 10 feet to scattered fragments of coaly material in sandstone, occur in a sandstone-coal series overlying a series of crossbedded red-buff sandstones. Both series are part of the Beacon group of sediments, and both show some evidence of pressure metamorphism. The sandstones are poorly cemented and are composed dominantly of rounded and often frosted quartz grains. The sediments have been broken and uplifted by a series of massive diabase sills. The broken nature of the sediments precluded an estimate of the amount of coal present. The Mount Gran coals are highly attrital banded anthracites and semianthracites that have most commonly a moderately dull luster but do include bright bands. Coal in contact with or near diabase intrusives is partly graphitic but shows no evidence of coking. Apparently the coal was beyond coking rank before emplacement of the adjacent intrusives. Fragments of the plant Glossopteris indica found with the coal suggest Permian age but do not prove it. The coals appear to be derived from plant remains that collected in shallow basins; individual coalbeds would tend to be lenticular bodies that formed in different places as the dominantly sandy sediments were deposited. The wide distribution of coal indicates that coal-forming conditions prevailed over much of the continent; the great thickness of Beacon sediments indicates that similar conditions may have persisted through a long period of geologic time. Generally similar coal deposits may occupy widely separated stratigraphic positions.

Jan 1, 1963

By George T. Krempasky

This report is one of a series of Bureau of Mines Information Circulars dealing with mining methods and costs throughout the United States. It describes drifting, crosscutting, and raising operations at several mines in the Coeur d'Alene mining district, Shoshone County, Idaho. Ore bodies in the Coeur d'Alene district are generally in steeply dipping tabular ore zones, are irregular in shape, erratic in occurrence, and have been extensively mined along the strike and down dip. Because of the extended attitude of the deposits a great deal of development work is required. Drifting, crosscutting, and raising methods are described in this report. Shaft sinking is the subject of another report in the same series.

Jan 1, 1960

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By Paul Biggs

This Bureau of Mines report contains information on 63 water flood projects in Colorado. Water was injected in 10 formations located in 58 oilfields. Specific field data presented include location, discovery, development, water supply, fluid injection, oil and water production, oil reserves, and oil recoveries by primary and secondary methods. An estimated 3.5 billion barrels of water has been injected to recover approximately 533 million barrels of oil, a ratio of 6.57 to 1. Most of the injection water is from alluvial deposits, although produced water is used in many fields. Injection water treatment is not a major problem. Appraisal of project success or failure in this report is based on technical, rather than economic, information.

Jan 1, 1974

By K. E. Stanfield

The Bureau of Mines oil-shale program, initiated in April 1944, is concerned with the future utilization of oil shale in the United States as a source of liquid fuel. One phase of this program is the accumulation of information on the location, extent, and richness of oil-shale deposits that may be suitable for processing to oil and related products. A previous publication5/ presented, by means of logs, the oil yields of sections of the largest known oil-shale deposit in this country -the shales of the Green River formation occurring in adjoining portions of the states of Colorado, Utah, and Wyoming. This present supplementary report presents the oil yields of cores from 48 holes drilled during 1952 to 1954 in the Green River formation of Colorado, which is distributed over an area of more than 1,000 square miles. The oil yields of the 48 oil-shale sections, involving the assay of 9,651 samples, representing 22,451 feet of core, are presented by means of logs. In addition, the oil yields of samples comprising the maximum sections of 15 gallon-per-ton shale are tabulated for these cores and for the 28 cores from Colorado which were logged in the previous report.

Jan 1, 1957

By R. D. Van Zant

The method for smelting zinc in horizontal retorts developed several centuries ago is still in use. This process consists essentially of the reduction of zinc oxide by carbon at 1,200° to 1,400° C. in a fire-clay retort. The reaction is highly endothermic, and a high radiation loss occurs in transferring the heat of reaction through the fire-clay walls. In recent years, silicon carbide retorts with much better heat-transfer characteristics than fire clay have been supplanting the old retorts. The practical impossibility of recovering the carbon monoxide formed in the reduction causes a large loss of fuel. Intermittent smelting is done in small retorts that are manually charged and discharged, and the furnace crews must be specially trained if efficient results are to be obtained. During the past 20 years several processes have been introduced that have substantially improved the horizontal-retort process. One of these, developed by the New Jersey Zinc Co., consists of a continuous process in which a briquetted mixture of zinc sinter, reducing agent, and binder is coked at 750° to 900° C. and charged into a vertical silicon carbide retort. A supply of displacement air or exhaust combustion gas is introduced at the base of the retort at an appropriate pressure in order to keep the zinc vapor from condensing on the cooled residue in the lower part of the retort. Any .oxidizing constituents in the displacement gas are converted to carbon monoxide by reaction with the carbon in the charge. The spent residue is continuously removed at the bottom of tl1e retort. The chief advantages of this process are said to be increased output per man-day, improved working conditions, high recovery of zinc, increased thermal efficiency, and long retort life.

Jan 1, 1950

By R. R. Faddick

A mineral slurry data hank has been compiled, containing slurry pipelining data on sixteen ores, concentrates, and tailings. The data bank it in the form of a computer print-out all they necessary system constants and headloss data for each mineral commodity. The purpose of the data bank was to assist in the development of a universal head loss correlation for mineral slurries, if such a thing exists. Present headloss correlations were tested and found to be inconsistent for the various mineral slurries. Consequently, a different approach was taken, that of compiling a library or Stanton diagrams relating friction factor and Reynolds numbers for a given slurry in a given pipe diameter. The advantages of the diagrams arc demonstrated and discussed. While this correlation shows excellent potential, it is necessary that additional work, both theoretical and experimental, be performed. In addition, two equations are given from which a design velocity may be obtained to minimize deposition or formation of bedload. The equations are based on data taken from the mineral slurry data bank.

Jan 1, 1972

By D. J. Parker

Before the various States began to enact workman's compensation laws accidents were considered inherent in many industries, and little or no effort was made to prevent or reduce them. The hazard was accepted by the employee with the job, and the avoidance of accidents by mental alertness or physical agility was largely his responsibility. After the employee had given evidence of enough skill inn performing his allotted task efficiently the responsibility of the employer apparently ceased with respect to the personal safety of the employee. However, following the enactment of workmen's compensation laws, at least two facts that had not before been fully appreciated soon became apparent: (1) The majority of accidents can be prevented if the management firmly determines to prevent them; (2) frog a monetary point of view alone accidents are decidedly expensive, both to employer and to employee. It is now evident that savings effected by conscientious safety effort add substantially to net profits of operation.

Jan 1, 1934

By E. J. Kloos

One phase of the work of the Bureau of Mines in health and safety is promoting the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum-performance requirements for the approval of self-contained breathing apparatus (1),4/ gas masks (2), supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks) (3), dispersoid (dust, fume, and mist) respirators (4), and nonemergency gas respirators (chemical-cartridge respirators) (5). Approval tests of self-contained breathing apparatus are conducted by Health and Safety District B; approval tests of other types of respiratory-protective devices are conducted by the Branch of Health Research. Manufacturers of respiratory-protective devices may submit their equipment to the Bureau of Mines for approval under the requirements of these schedules. If the device, when tested by the Bureau, meets the schedule requirements, a certificate of approval will be granted, which not only states that the equipment has passed the schedule requirements but also gives information about the limitations of the device. If it is found at any time that approved devices do not meet the requirements of the pertinent schedule, the Bureau may rescind approval.

Jan 1, 1959

By H. B. Humphrey, F. E. Cash

The following information on accidents in Alabama during 1930 was compiled from data obtained from the companies represented in a course on accident prevention given by the United States Bureau of Mines in Birmingham. These mines produced nearly three-quarters of the tonnage of that State for the year, and included most of the larger operations in the district. The figures are probably representative of the mines which are doing recognized safety work, and are better than the average for all the mines in Alabama. Table 1 lists the days lost in accordance with the weights given to fatalities and permanent disabilities, part and total, which is the scale used in the National Safety Com¬ petition for Mines, conducted by this bureau. By way of explanation, temporary disabilities are weighted according to actual number of calendar days of disability, including Sundays and holidays — that is, all days are counted except the day of accident and day of employee's ability to return to duty. Hernia is classed as a temporary disability to be charged with the actual number of calendar days during which the employee was unable to work. Table 2 gives the number of accidents and the days lost from each cause at 45 coal mines and 7 iron ore mines, also the average frequency and severity rates.

Aug 1, 1931

By D. Harrington

The record of fatalities from mine explosions in the United States during the fiscal years 1934 to 1937 wars the best in the history of the mining industry; that for the fiscal year 1939, however, is not so favorable, since nearly as many men (170) were killed by explosions in 1938 as were killed during all of the previous 4 years (182). In spite of the large increase in fatalities from explosions during 1938, the average for the past 5 year period (70.4) is less than one-half the average (13) of the preceding 5 year period. The reasons for the large increase in the number of explosion fatalities during the 7 past year as compared with the previous 4 year are not entirely clear; it is: evident, however, that in some instances there has been laxity in the enforcement of State minim laws, and also that come of our coal-mining people, including workers and operating officials, have failed to carry out tine known precautionary measures to prevent explosions.

Jan 1, 1939

By Wing G. Agnew

The first six Reports of Investigations in this series , pertaining to the investigation of stemming at the Mount Weather Testing Adit, dealt with ( 1 ) the dust produced by blasting , ( 2) the effect of stemming upon gases generated by blasting , ( 3 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 60 - percent ammonia gelatin dynamite , (4) the length of stemming material through which a primer will fire and detonate a charge of dynamite , ( 5) comparison of dust and gases produced when blasting charges of dynamite in drill holes , bombs, and mud - cap shots , and ( 6 ) the relative advantages and disadvantages of different types of stemming and no stemming when used with 40 - percent ammonia gelatin dynamite .

Oct 1, 1943

By Jr. Koch

Statistical methods applied at the Bureau of Mines Denver Mining Research Center to data from metallic ore bodies were used to evaluate lignite reserves from core data and to predict the extent of lignite horizons in some Texas lignite beds. Six lignite seam units were studied using data from 361 drill holes. The data indicate a total of 214.2 million tons of lignite in the area examined, and probable reserves of 113 million tons in an area 2,000 feet beyond the limits established by the drill holes. It was demonstrated that lignite reserves present in lenticular beds could be reliably determined by statistical techniques, and that core drilling could be optimized to maximum information with minimum drill holes. The technique described is applicable to other coal beds.

Jan 1, 1966

By W. E. Miller, G. S. Scott, G. W. Jones

"An important activity of the Bureau of Mines is the promotion of safety in mining and industry. In connection with these activities, the Bureau determines the explosion hazards of combustible gases, liquids, and solids and investigates means by which explosions may be eliminated or reduced in violence.The limits of inflammability and ignition temperature of combustible gases, vapors, and solids are of practical importance because such materials can be manufactured, transported, and used with greater safety, provided the range of concentrations and temperatures that cause explosions are known.Many organic compounds, which until a few year ago were merely laboratory curiosities, are now being manufactured in large quantities owing to the national emergency, particularly those chemicals entering into the manufacture of synthetic rubber, a product that is playing a major role in the Government program of national defense. This re Jolt gives results relative to the limits of inflammability of styrene and its ignition temperature in air and oxygen. This combustible liquid is now used extensively in the manufacture of synthetic rubber."

Mar 1, 1942

By M. Hayashi

The Bureau of Mines conducted laboratory studies on Idaho mudstones to examine techniques for extracting vanadium. Recovery of vanadium from low-grade sources could contribute to future vanadium production and reduce reliance on imports. An Idaho mudstone surface sample containing 0.30 pct V205 and an underground sample containing 0.21 pct V205 were used in the extraction tests. Leaching of the surface sample for 18 h at 800 C with the addition of up to 1,000 lb/ton H2S04 recovered 70 pct of the vanadium. How-ever, leaching of the underground sample under the same conditions re-covered only 47 pct. By adding 15 wt pct NaCl and roasting the samples at 7500 C for 2 h, followed by leaching with 800 lb/ton H2S04, vanadium extractions were increased to 78 pct from the surface sample and 83 pct from the underground sample. Water leaching of samples roasted at 7500 C for 4 h with a 25-wt-pct NaCI addition yielded about 60 pct of the vanadium from both surface and underground samples. Autoclave leaching at 2000 C for 3 h with 1,000 Ib/ton H2S04 extracted 97 pct of the vanadium from the surface sample and 86 pct from the underground sample. An exploratory solvent extraction investigation to purify and concentrate vanadium in the leach solution using several organic reagents was also conducted.

Jan 1, 1985

By Harold Bailie

The purpose of this Bureau of Mines report is to furnish information on mining practices applied to flat-bedded fluorspar deposits in southern Illinois. It presents new and improved operating procedures and specialized techniques applicable to deposits of this type. All of the operating mines of the Ozark-Mahoning Co. in this area have been opened by vertical shafts which connect with levels consisting of haul-age ways, stopes, and loading stations. The stoping practice used locally called room and pillar, is open stoping with pillars left at different distances and diameters. To facilitate haulage and drainage, the mines are worked from openings turned off the main haulage drift on a grade to conform with the dip of the ore beds. The ore is predominantly fluorspar with smaller amounts of galena and sphalerite that contain traces of cadmium and germanium. The principal gangue minerals are limestone, calcite, shale, barite, and sandstone. The rock hardness ranges from relatively soft shale to hard, abrasive sandstone.

Jan 1, 1960

By L. S. Harner

This paper which describes the milling practice at the Golden Cycle mill is one of a series of similar papers being prepared by the United States Bureau of Mines. The mill of the Golden Cycle Corporation, formerly known as the Golden Cycle Mining and Reduction Co., is located at Colorado Springs, Colorado, and has been operated since 1907. It is now and has been from its inception almost exclusively a custom mill.

Jan 1, 1933

By W. D. Ryan

The organic act passed by Congress in 1910 instituting the Bureau of Mines provided that the director of the bureau should promulgate such investigations as might be necessary to determine the causes of mine accidents and the best methods of preventing them. With the object of accident prevention in view, Director Joseph A. Holmes, and others who were pioneers in the bureau, conceived the Plan of having first-aid and mine-rescue training as one of the major activities of the Bureau. Out of this plan grew the first-aid and mine-rescue contests, which have been featured as an incentive for men to take courses in this type of mine safety training. The first appropriation for mine-accident investigations became available on July 1, 1908, under the jurisdiction of the U. S. Geological Survey, with Dr. J. A. Holmes in active charge. During 1908 there had been some first-aid training in the Pennsylvania anthracite field and a start made in Illinois, although there appears to be no exact information as to when or where first-aid training in the mining industry first became a reality, it is generally conceded that the St. John's ambulance corps of Scotland was one of the first - if not the first - to make the work effective. In 1911, to celebrate the establishment of the Bureau of Mines and the formal opening of the Pittsburgh, Pa., station, a first-aid and mine-rescue demonstration was conducted on Forbes Field, Pittsburgh. President William Howard Taft and many other men notable in public life were 2 resent. This was the first general national contest of the kind held it the United States; and since then there have been a number of nation-wide first-aid and mine rescue contests, as well as some which have been international in scope. There are over one hundred first-aid and mine-rescue contests of various kinds held annually in connection with mining and the allied industries.

Jan 1, 1929