Search Documents

By L. S. Sundae

The Bureau of Mines conducted a series of tests to compare the cutting forces required by radial and point-attack bits when making similar cuts. Three radial and four point-attack bits were tested in two coal mines using the Bureau's in-seam tester to measure coal-cutting forces in situ. Tests were also conducted to investigate the effects of weathering and cleating. The test results show that in each case, at a specific clearance angle, the radial bits required less tangential and much less normal force than the point-attack bits. The resultant of the cutting forces for some types of cut was 50 pct less at mine 1 for radial cuts compared to cuts with the best point-attack bit, and 40 pct less at mine 2. There was some difference between three types of radial bits, but it was not as significant as the difference between each type of point-attack bit. Cutting coal perpendicular to the cleat planes required less cutting and normal force than the same type of cuts parallel to the cleat planes. Test results showed no effect due to weathering on cutting force data. Cutting parallel increased forces only because cuts were made in the rock band.

Jan 1, 1987

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the U.S. Bureau of Mines to aerosol measurements in diesel-equipped underground noncoal mines. The first technique is based on size-selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately submicrometer in size while the mineral dust fraction of the aerosol is mostly supermicrometer in size. The second technique, chemical mass balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size-distribution data were modeled using a lognormal regression to parameterize the submicrometer and supermicrometer fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. Using this analysis, 97 ± 2 pct of the submicrometer aerosol mass was attributable to diesel exhaust aerosol.The CMB analysis, applied to both fractions of the respirable mi11e aerosol, yielded the amount contributed to each by the diesel and dust aerosol sources. On the basis of this analysis, 94± 10 pct of the submicrometer fraction was diesel exhaust aerosol. As much as 20 pct of the diesel aerosol, however, was found in the supermicrometer fraction, requiring a correction of the submicrometer fraction results to account for the missing diesel mass. More accurate measurements will require a carbon-specific analysis of the aerosol.INTRODUCTION Measurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and CMB modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample."

Mar 1, 1992

By BUREAU OF MINES

LIST OF PUBLICATIONS ON CERAMIC INVESTIGATIONS U.S. BUREAT OF MINES .

Jan 1, 1923

By A. L. Engel

This report describes laboratory-scale experimental treatment of six base-metal ore samples taken by engineers of the Bureau of Mines, Region II, while investigating ore deposits in California and Nevada. The information is of interest in developing the mining districts represented or when similar ores from other sources are being studied. Simple treatment methods were employed as far as possible. More complex treatments also were tried when necessary. The possibilities and limitations of the methods applied to the several ores are shown by the data herein reported.

Jan 1, 1960

By W. P. Yant, R. R. Sayers, G. W. Jones

In the treatment of any illness the early diagnosis is of very great importance . This is especially true in cases of carbon monoxide poisoning , whether acute or sub-acute in character. A diagnosis of CO poisoning is usually made from a correlation of the history , the possible place of exposure , and the symptoms produced . This , however, is not positive evidence because CO often is present in unsuspected places and can be absent in suspected places . Also , the symptoms of this type of poisoning are common to other causes . In many such cases the correct diagnosis may be very difficult , if not impossible by this method and as a result little or no treatment is given . Sub- acute cases , those in which the subject is exposed to concentration sufficient to cause only headaches , malaise , feeling of weakness and dizziness , may be incorrectly diagnosed and as a result , improperly treated . Probably the best method of diagnosis is by examination of the subject's blood . Many methods for the detection of CO in the blood have been developed , but owing to their various individual disadvantages have never come into common usage . Some of the quantitative methods are satisfactory with regard to accuracy but require elaborate and expensive apparatus , special technique and training, or are too delicate and cumbersome for field use . It is of vital importance in all industrial and domestic accidents occuring at places where CO might be suspected or where the symptoms are typical of CO poisoning that a qualitative and preferably a quantitative determination be made the extent of poisoning being of importance in deciding whether CO was the direct or contributary cause) to show the presence or absence of 0. This is indeed essential from a medical standpoint as it aids in prescribing treatment and from a legal standpoint to insure justice in the claims that are often unjustly decided for want of positive evidence.

Jun 1, 1923

By M. Clair Smith

The Bureau of Mines investigated the Rip Van Winkle mine, which is about 25 miles northwest of Elko, Nev., from October 1942 to February 1943 to determine possible resources of lead-zinc-silver ore. The property is owned by the Rip Van Winkle Consolidated Mining Co., which maintains its offices in Salt Lake City, Utah. Ore was discovered in the 1860's, and active mining was carried out intermittently until 1939, when the Rip Van Winkle Consolidate Mining Co. acquired the property. This company equipped and developed the mine, erected a flotation mill, and operated on a 65-ton daily basis. The ore is mined from veins, mineralized faults, and replacement deposits of wall rock. The country rock comprises cherty shale, granite, porphyry, intrusive breccia, and breccia, and brecciated shale. Mining operations were carried down to the 700-foot level. The Bureau of Mines drilled 5 diamond-drill holes, totaling 1,084 feet, from the 600- and 700-foot levels, excavated a 250-foot surface trench, and took 26 underground samples. The ensuing sections note the location and physical features of the district, mention the equipment, and specify the property and ownership. The history of the mine is briefed, and the geology, mine workings, and plant are described. The work performed by the Bureau of Mines is summarized and supplemented in detail by assay maps, logs of diamond-drill holes in appendix A, and by tables of sample analysis in appendix B.

Jan 1, 1949

By J. H. Weber

This Bureau of Mines publication describes the hardware system and software package for the semiautomatic acquisition and automatic processing of high-resolution mass spectrographic plates. The semiautomatic data acquisition allows a tenfold saving of time compared with manual data acquisition. Automatic processing of the high-resolution data to yield exact masses, intensity, and the corresponding empirical formulas is accomplished by efficient programming on a small, inexpensive, programmable calculator system.

Jan 1, 1974

By J. C. Edwards, C. C. Hwang

A Computational Fluid Dynamics (CFD) program was used to model buoyancy induced Product-Of-Combustion (POC) spread from experimental fires in the National Institute For Occupational Safety And Health (NOSH), Pittsburgh Research Laboratory (PRL), safety research coal mine. In one application, the CFD program was used to predict spread from fires in an entry under zero airflow conditions. At a location, 0.41 m below the entry's roof at a distance of 30 m from the fire, the measured smoke spread rates were 0.093 and 0.23 m/s for a 30 and a 296 kw fire, respectively. The CFD program predicted spread rates of 0.15 and 0.26 m/s based upon the measured fire heat production rates. Based upon a computation with [c3h3] as the hydrocarbon fuel, a predicted 5 PPM co alert time of 70 s at a distance of 30 m from the fire is to be compared with the measured alert time of 148 s. In a second application, the CFD program was used to analyze smoke flow reversal conditions, and the results were compared with visual observations of smoke reversal for 12 diesel fuel fires. The CFD predictions were in qualitative agreement with visual observations of smoke reversal.

By D. H. Yardley

A major purpose of this contract was to evaluate a variety of dust suppressants to determine their effectiveness in mitigating dust from taconite tailings. During the course of the investigation tailings from pilot-plant tests of Minnesota copper-nickel ores became available and chemical binders were also tested for dust mitigation effectiveness on this mineralogically different material. Field-test plots were established on taconite tailings and wind tunnel laboratory tests conducted. The laboratory tests consisted of comparing treated and untreated samples at wind velocities of 40 mph using a weight-loss method and direct dust emission measurements. It was shown that the emission of fine dust from taconite tailings, in the range of 4.5 microns to 0.85 microns, could be reduced by 99 percent using certain chemical suppressants. It was also demonstrated that a straight water spray on coarse tailings (3/4" to + 10 mesh) reduced dust emission by 95 percent. Although eight different chemicals were tested, most of the tests were made using Coherex, ammonium lignin sulfonate and sodium silicate. These same dust suppressants were used, singly and in combination on almost 75 field-test plots. The Coherex appears to provide the best results in terms of economics and durability. Wind tunnel tests on treated and untreated Cu-Ni tailings demonstrated that applications of dust suppressants reduced fugitive fine dust by better than 99 percent.

Jan 1, 1980

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines collected and analyzed overcore measurements and other indicators of in situ stress characteristics at the Lucky Friday Mine, Mullan, ID. An analysis of these data revealed that significant local variations in in situ stress are present in this mine and that these variations existed prior to mining. High stresses were found to be associated with the most competent strata and a locked section of a fault. An estimate of the predominant stress field was developed for mine-wide modeling. The estimate shows that the greatest principal stress was oriented north of northwest. This information should provide a basis for mine-wide structural modeling of the Lucky Friday Mine and should generate important insights into localized stress conditions, which may significantly affect both local and mine-to-mine variations in seismicity induced by excavation.

Jan 1, 2010

By Jr. Koch

As a means of investigating the distribution and variability of gold in ore from the Homestake mine, Lead, S. Dak., the Bureau of Mines performed a designed sampling experiment, and assay results were statistically interpreted. Fifty-six feet of diamond-drill core from five boreholes was sawed into l-inch-long cylinders, which were sampled randomly and were assayed. Analyses of variance of the assay results were used to compare and assess the different types of variation: within drill holes, among paired drill holes, among unpaired drill holes, and among furnace runs. The extreme variability in gold mineralization found is the natural variability on the smallest scale that can be detected by fire assay; most of the variability is associated with among-feet rather than within-feet sample intervals. Because of the extreme variability, one-half of the gold is in 3 percent of the samples.

Jan 1, 1967

By John E. Husted

Quantities of kaolin in Georgia in-contiguous or single bodies had been established by previous work to be sufficient for an alumina industry. The need for characterization of this kaolin to determine its suitability as an ore of aluminum resulted in the studies described herein. It was determined in an area roughly 7 x 27 miles, known as the Wrens district that approximately 5.9 billion short tons of kaolin averaging 35.55 percent A1203 exist in an essentially continuous clay body. The Macon-Sandersville district consists of discontinuous kaolin bodies averaging 35.28 percent A1203 with an average thickness of 28 feet. Tonnages for this district are not available. One hundred and twenty core samples of kaolin were analyzed for K20, CaO, MgO, Al203, T102, Cr203, Fe203, Si02, P205, and F. The P205 and F were analyzed by wet chemistry methods and the others by electron microprobe. Seventy-nine of the samples were from the Wrens district forty from the Sandersville-Macon district and one from the Andersonville district. Emission spectroscopic analyses were also made to qualitatively determine all elements present for each core. X-ray diffraction studies were made of each core to determine mineral species present. Scanning and transmission electron microscope pictures also are given for each I' core sample. Elevations, overburden thickness, and kaolin thickness are given for each core site as well as map locations. Isopachs for over-burden and kaolin thickness are given for the Wrens district.

Jan 1, 1983

By H. P. LeVan

The Bureau of Mines has developed a technically feasible continuous single-stage leaching and thickening system for extracting manganese from umber by a sulfuric acid-ferrous sulfate process; the cocurrent leaching and thickening system proved simpler to operate and control than the countercurrent leaching and thickening system developed earlier" Related tests investigated the use of a centrifuge to replace thickeners for separating the product liquor from are residues and compared several chemical agents for removing iron from the pregnant manganese leach solutions. Results of Some exploratory autoclaving tests are also given.

Jan 1, 1972

By Abrasive Materials

Table 1.-Salient abrasive statistics in the United States [ ]

Jan 1, 1967

By D. I. Bleiwas

The Bureau of Mines determined demonstrated tin resources and costs associated with tin production in order to evaluate the potential for tin production from 18 market economy countries (MEC's). Data were collected from tin producers, in most cases during on-site visits. The analyses evaluated the relative economic and resource position of 146 mines, deposits, or regions in January 1984 dollars. The demonstrated resource of recoverable tin within the nations studied is approximately 2.8 million metric tons (mt). Of this total, over 73 pct is recoverable from the Southeast Asian countries of Malaysia, Thailand, and Indonesia, which in 1983 accounted for almost 60 pct of the world's tin production. Brazil has joined the Southeast Asian countries as a major low-cost, high-volume supplier of tin and is likely to continue to expand its production. Given the 1984 market structure, over 60 pct of the tin in demonstrated resources was economically recoverable. Historically, the International Tin Council (ITC) has helped maintain relatively stable tin prices through a buffer stock and sales quotas. In late 1985, exhaustion of buffer stock funds led to suspension of tin trading on the world's major tin metal exchanges.

Jan 1, 1986

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By John M. Dower, Ralph W. Plummer, Terrence J. Stobbe, Hyunwook Kim

"The relationship between exposure to coal mine dust and the development of various respiratory diseases is well recognized. The cause of these diseases however. Is still uncertain. To study this cause-effect relationship, It Is necessary to characterize the coal mine dust In terms of the quantity of dust present and mineral content of the dust. Dust samples were collected using a Portable Continuous Aerosol Monitor (PCAM) and 4-stage cassette Impactors at various locations in an upper Freeport seam coal mine In West Virginia. The samples were analyzed using an X-ray microdiffraction film technique and energy dispersive scanning electron microscopy. This paper presents the results of the first phase of this characterization work which Includes determining the size distribution of the dust and the mineral content of the size intervals.IntroductionDiseases associated with dusts in coal mine environments continue to afflict miners in today's modem mines. These diseases still persist because, as Olishifski points out an employee rarely experiences exposures to a single environmental stress but rather to an Intricate Interplay of multiple stresses.(1) In the case of coal mining the multiple stresses are varying sizes of dust particles originating from coal imbedded minerals. Immediate roof strata bottom strata. Incombustible rock and the coal itself. The site of this Intricate Interplay Is the miner's lungs and the resulting diseases are a function of the composite dust exposures.The proper study of coal mine dust toxicity requires that the dusts used replicate existing coal and mineral dust compositions in their relevant size fractions. The purpose of this project is to develop the size and mineral content data necessary to support this ongoing toxicological effort.Existing coal mining standards and regulations also address total and respirable dust exposures. These dust terms refer to both the quality and quantity of the dust segment in the mine atmosphere. Dust quality addresses its coal and mineral content. whereas dust quantity Is described by mass per unit volume (mg/m3) The comprehensive characterization of coal mine dust exposures will enable revision of these standards and regulations to address the specific minerals and size fractions found to be toxic to human lung tissue."

Mar 1, 1989

By Robert F. Holub

The Bureau of Mines has made a study of the magnitude of the variations of radon daughter mixtures, with the objective of determining whether these variations reflect the existing physical conditions in uranium mine atmospheres or if they are merely random or systematic errors. To accomplish this, many data have been plotted using a triangular graphing technique which shows that plateout affects RaA more than RaB or RaC, and that it is impossible to find simple correlations between working level ratios, radon daughter mixtures, and age.

Jan 1, 1978

By Austin Gudmundsen

"The smoke nuisance, like many other undesirable and longstanding features in our present civilization, is still with us. On reviewing the situation we are astonished to find no authentic record of a major smoke-abatement campaign that has succeeded in eliminating a smoke nuisance, in spite of the fact that the problem has been with us since the use of bituminous coal began. We might well ask ourselves where the trouble lies; is the problem impossible of solution? We can not blame the average citizen for harboring this thought as a conviction. He has been urged for so long but sees so little evidence of progress. He has repeatedly been assured by the scientist and the engineer in most convincing terms that smoke. is unnecessary, that it can be avoided; small wonder is it that he is beginning to distrust so-called authority on the subject.On the other hand, the scientist and engineer are entirely within their rights. We all know that even high-volatile coal can be and is now being burned with no visible smoke. We know that even small domestic heating furnaces, with favorable conditions and with proper care, can be fired by hand without producing much smoke. And we know that when such equipment is fitted with suitable stoking devices, little or no smoke results. What, then, is the answer?Perhaps we may learn something from a critical examination of a typical smoke-abatement problem. Probably one of the most enlightening campaigns that has been waged in the United States is that of Salt Lake City, Utah; therefore, the purpose of this paper is to discuss the important aspects of this particular case."

Apr 1, 1930

By W. Beckering

In characterizing tars obtained by the low-temperature carbonization of North Dakota lignite, infrared spectra have been an invaluable aid in both qualitative and quantitative examination. Quite, early in the tar-research program of the Federal Bureau of Mines it became evident that the small number of published spectra available for hydroxy-aromatics would be inadequate for comparative purposes when dealing with the wide range of compounds present in coal tar; therefore, compiling a catalog of spectra was begun as a continuing part of the tar program. Because these spectra should be valuable to other investigators in this and related fields, they are being presented in these reports. This supplement to the original publications presents the spectra (figs, I to 32), representing 32 compounds, largely phenolic materials. The major problem of this project has been the availability of materials for examination. Most of the compounds included in this supplement were synthesized at the Bureau of Mines Lignite Research Laboratory. Some were obtained from commercial sources, whereas the compound 2'-hydroxy-l-phenylnaphthalene was synthesized at the Bureau of Mines laboratory in Bruceton, Pa. The spectrum of 2-ethyl-4-methylphenol, figure 32, is a correction of the spectrum presented as figure 26 in the original reports

Jan 1, 1961