Search Documents

By C. L. Karr

The U.S. Bureau of Mines is currently investigating the use of genetic algorithms (GA's) for solving optimization problems. This computer search technique, based on the mechanics of natural genetics, was used to perform simple least squares curve fitting. Three examples are presented in which a GA manipulates binary coded strings to produce near-optimal solutions to least squares curve-fitting problems after having viewed only a small portion of the search space. The examples include fitting data to the equation of a line, the equation of a parabola, and the Ree-Eyring equation.

Jan 1, 1991

By B. W. Gandrud

[The Bureau of Mines is conducting an extensive investigation of coal preparation in the Alabama coal fields in cooperation with the University of Alabama and coal-mine operators. In this investigation the drainage characteristics of typical coals from the Warrior and Cahaba n fields were studied. Tire main purposes of this study has been to evaluate no nearly as possible relative influences of certain factors on rate of drainage and to determine whether the drainage characteristics of coals from different beds or from different mines on the soma bed differ materially. A further objective was the development of a laboratory drainage test that would predict approximately the rate at which any coal will drain after having been loaded into a railroad car in a saturated condition. The study has been confined to samples of slack coals - that is, coals from which none of the fine sizes have been removed. The samples ranged in upper size limits from 7/16 inch to 3 inches. It did not seem necessary to study nut and egg sizes, that is, sizes from which the fine coal has been removed by screening, as these lose water so rapidly by natural drainage that they present no serious problem in dewatering after treatment in a washer. The significance of drainage characteristics of Alabama coals is apparent in view of the fact that not less than 70 percent of Alabama?s total coal product is subjected to wet washing before being materials.]

Jan 1, 1941

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By Samuel S. M. Chan

The objective of this project was to collect information applicable to the design of ground support systems in deep mines to include in-situ rock deformations, deformation-modulus, stresses, and geology and laboratory physical properties. All data collected was to be integrated and evaluated using a finite-elements computer code. In addition, considerable professional "cross pollenization" was anticipated from the association of University and SMRC personnel. Scope of Investigation Before a ground supporting system can be evaluated, the loading conditions existing in the region of investigation, strength, deformation characteristics, as well as other engineering properties of the rock structure immediately surrounding the openings, together with the pertinent geological information, must be obtained and analyzed. It was for this reason the following items were included in this research project: (1) The selection of a suitable area for the investigation. (2) The mapping of the important geological features of the area of investigation. (3) The measurement of in-situ deformation of rock masses immediately surrounding an underground opening of the area of investigation. (4) The determination of ground stresses. (5) The obtaining of in-situ modulus of deformation of the rock masses. (6) The testing of useful engineering properties of

Jan 1, 1972

By Austin Gudmundsen

"The smoke nuisance, like many other undesirable and longstanding features in our present civilization, is still with us. On reviewing the situation we are astonished to find no authentic record of a major smoke-abatement campaign that has succeeded in eliminating a smoke nuisance, in spite of the fact that the problem has been with us since the use of bituminous coal began. We might well ask ourselves where the trouble lies; is the problem impossible of solution? We can not blame the average citizen for harboring this thought as a conviction. He has been urged for so long but sees so little evidence of progress. He has repeatedly been assured by the scientist and the engineer in most convincing terms that smoke. is unnecessary, that it can be avoided; small wonder is it that he is beginning to distrust so-called authority on the subject.On the other hand, the scientist and engineer are entirely within their rights. We all know that even high-volatile coal can be and is now being burned with no visible smoke. We know that even small domestic heating furnaces, with favorable conditions and with proper care, can be fired by hand without producing much smoke. And we know that when such equipment is fitted with suitable stoking devices, little or no smoke results. What, then, is the answer?Perhaps we may learn something from a critical examination of a typical smoke-abatement problem. Probably one of the most enlightening campaigns that has been waged in the United States is that of Salt Lake City, Utah; therefore, the purpose of this paper is to discuss the important aspects of this particular case."

Apr 1, 1930

By A. H. Beebe

This paper describing the operations of the Cresson mine of the Cresson Consolidated Gold Mining & Milling Co. at Cripple Creek, Colorado, is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. The Cresson has recently been the most, important mine in the Cripple Creed district. During 1932 and 1933 an average of 230 tons of new ore (excluding dump material) that averaged about $10 in gold was shipped daily; 150 to 175 men were employed. Stoping was by the shrinkage method exclusively. The ore was screened washed, and hand-sorted at the surface and shipped to the Golden Cycle mill at Colorado Springs for treatment. A considerable proportion of the production was made by lessees working under the so-called "split-check" system. The authors are indebted to the management of the Cresson Consolidated Gold Mining & Milling Co. for permission to publish this paper.

Jan 1, 1934

By L. H. Kalenowski

The metal lithium, its alloys, and its salts are becoming Increasingly important as industrial materials. Lithium metal, because of its great affinity for elements, such as nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, has become important for a wide variety of uses, ranging from purifying helium gas by removing the nitrogen to scavenging molten metals of undesirable impurities. The excellent fluxing properties of lithium salts have found increasing use in such applications as fluxes for welding aluminum and in lower melting ceramic glazes and coatings. Lithium chloride is one of the most hygroscopic salts known and is widely used as a dehumidifying agent. .About 17 lithium minerals are known. Four of these have commercial importance: Amblygonite, lepidolite, zinnwaldite, and spodumene. Spodumene is the most important source of lithium and lithium salts at present, but sizable deposits of amblygonite occur in the pegmatite area of the Black Hills of South Dakota. The size and nature of these deposits preclude the, possibility of, any assurance of an adequate supply of amblygonite for an operation processing only this mineral. Frequently spodumene and amblygonite occur associated in pegmatite minerals. Preliminary investigations indicate that a simultaneous recovery of spodumene and amblygonite can be made by froth flotation. A single process for treating spodumene and amblygonite or mixtures of thorn, would make possible more use of amblygonite as a source of lithium and obviate the separation of spodumene and amblygonite when they occur together.

Jan 1, 1952

By T. E. Howard

The western phosphate field, comprising parts of Idaho, Montana, Wyoming, and Utah, contains one of the world's largest known reserves of phosphate rock. Although phosphate-rock deposits of good-grade have been known since before the turn of the century and production has been recorded since 1906, real development of this important field did not begin until immediately after World War II. Since then fertilizer-manufacturing facilities using western phosphate rock have been expanded, and three electric-furnace plants for producing elemental phosphorus have been installed, resulting in a rise in mine production from 323,955 long tons2/ in 1945 to 1,653,916 long tons3/ in 1953. Interest in the field is increasing, and it is reasonable to expect that the western phosphate industry will continue to expand. Before 1945 all western production was from underground mines. In that year the first strip mine in the field was started near Montpelier, Idaho,~ and in sub-sequent years a number of other open-pit mines were opened in southeast Idaho and western Wyoming. At present the major part of the production comes from surface mines. Underground mining has continued, and new underground mines have been opened in the field, but recent exploration by operating companies has been aimed primarily at developing additional deposits suitable for low-cost surface mining. Preliminary reserve estimates by the Federal Geological Survey5/ indicate that only a very small part of the total resource may be recovered by surface methods and that the industry eventually must depend largely on underground mining. Because one function of the Bureau of Mines is promoting the conservation and development of the Nation's mineral resources, it is appropriate that research be conducted to develop low-cost maximum-recovery underground mining methods applicable to western phosphate-rock deposits.

Jan 1, 1956

By William Y. Mo

This Information Circular provides a detailed background documentation of how the Bureau of Mines projects U.S. mineral demand to the year 2000. These statistical projections serve as a quantitative basis for contingency forecasting of the low, high, and probable U.S. demand for nonfuel minerals by end-use categories and are published in the Bureau of Mines Mineral Commodity Profiles and Mineral Farts and Problems series. Aluminum is used as an example in this study.

Jan 1, 1980

By Andrew D. O. O’Brien, Linda J. McWilliams, Joe L. Howell, Douglas E. Pollock, Jeanne A. Zimmer, Andrew B. Cecala

A quick, safe, and effective method has been developed that allows workers to clean their dust laden work clothing periodically throughout the day. For the mining industry, this technique is much more effective than the current federally approved method of using a vacuuming system. This newly designed method is relatively inexpensive and can be easily installed at any operation to allow workers to clean their clothing without contaminating the worker, the work environment. or co-workers to elevated respirable dust levels. This clothes cleaning process uses an air spray manifold to blow dust from a worker's clothing in an enclosed booth, which combines the dust for capture and removal by a baghouse dust collector. Since the air exhausted by the dust collector causes the booth to be under negative pressure. no measurable quantities of dust were ever measure escaping from the booth to contaminate the work environment and/or other workers. The worker performing the cleaning process is required to wear a half-mask fit- tested respirator with an N 100 filter, hearing protection, and full seal goggles. Dust samples taken inside the respirator of test personnel performing the clothes cleaning process showed very minimal to no respirable dust. This clothes cleaning process was performed in less than 20 seconds and was significantly y cleaner than either the Federally approved method of vacuuming, or the most common method or using a single compressed air hose. It was also determined during this research that polyester-cotton blend coveralls clean more effectively than coveralls which are 100 percent cotton. The newly designed clothes cleaning process has potential application to any industry where workers' clothing becomes contaminated with most any type of dust or product.

By James J. Scott

Workshops were held in eight states during the period from December 12. 1975. through June 25, 1976, under U. S. Bureau of Mines Contract to the University of Missouri-Rolla. The workshops were designed to help define the Bureau's research and development priorities. At each workshop a summary of the current Bureau mine reclamation research was presented which was followed by identification of problems associated with mine land reclamation in the state where the meeting was being held. Discussions included the seriousness of problems locally and how the Bureau could best undertake research to assist the state in solving the problems identified. Participants included representatives of state agencies, educational institutions, and companies involved in surface mining. Attendance at these workshops totaled 201 persons who displayed a wide variety of opinions and ideas as to what should be done In government research and development efforts. A breakdown of these attendees is as follows: 91 state and Federal employees; 69 mine operators, equipment manufacturers and consultants; 33 educators and researchers; and 8 others representing such varied interests as environmental and conservation groups, news media and students .

Jan 1, 1976

By A. Sainato, S. J. Kravits, G. L. Finfinger

This report describes a project conducted by the Bureau of Mines in which the accurate directional drilling of a borehole was demonstrated with the objective of intercepting a designated target. The project was conducted at Navajo Dam in northern New Mexico at the request of the Bureau of Reclamation. Borehole survey and drill logs are provided in an appendix. The trajectory of the demonstration borehole was designed to intercept a 5-ft-radius target at the final or "punchout" distance of 885 ft. The elevation of the borehole at this distance was within the target; the borehole punchout coordinates were 8.81 ft southwest of the target. As a result of the demonstrated accuracy, the Bureau of Reclamation has contracted the accurate drilling of boreholes as long as 600 ft from the inside of a short tunnel, to control water seepage in the right abut- ment. This resulted in a substantial cost savings compared to the orig- inal plan of constructing a longer tunnel and drilling 150-ft boreholes.

Jan 1, 1987

By K. K. Kelley, W. W. Weller

The heat capacities of four crystalline silicates of barium ( BaSiO3 , BaSiO4 , Ba Si¸0 , and BaSi₂0 ) and two crystalline silicates of strontium (SrSio and Sr₂Sio ) were measured over the temperature range from 51 ° to 298° K. The results were used to evaluate the entropies at 298.15 ° K. The entropy values were joined with known heats of formation to obtain the free energies of formation of the silicates with respect to their constituent oxides at 298.15 ° K.

Jan 1, 1964

By Clarence Hall, J. J. Rutledge

Many of the fatal accidents in coal mines have resulted from the Explosives used in Use of explosives for breaking down the coal. These accidents have resulted both from the use of explo- sives that were not suitable and from the careless or improper use of suitable explosives. Investigation has shown that one of the commonest causes of dis- astrous explosions in the coal mines in this country has been a blown- out shot of black blasting powder or dynamite. The dangers that attend the use of these explosives were perceived several years ago, and in consequence the attention of powder manufacturers was directed to the production of explosives that would be less liable to ignite inflammable gas or dust. The manufacturers have been so successful in their efforts that it is now possible to obtain explosives which yield much shorter and quicker flames than black blasting powder or dynamite, and hence are much less dangerous to use in fiery or dusty coal mines. of explosives. To find out which of the many grades of short-flame explosives Government tests have the qualities that render an explosive most effective and least dangerous for mining coal, the United States Government established a testing station at Pitts- burgh, Pa., in 1908. This station is now under the charge of the Federal Bureau of Mines. Before the station was opened a state- ment of the requirements that the explosives in question would have to satisfy was drawn up and sent to manufacturers. A number of these sent explosives to be tested, and on May 15, 1909, a list of the explosives that had passed the tests was published. Since that date other brands of explosives have been tested and three more lists have been issued. The latest list, published in Miners' Cir- cular 2, Bureau of Mines, contained the names of no less than 71 explosives that had passed the tests prior to January 1, 1911.

Jan 1, 1912

Control shearer-generated airborne respirable dust on longwall mining sections. Approach Previous Bureau studies have shown that using high-pressure water can have a significant impact on the amount of airborne dust released into the face airflow while cleaning and controlling the airflow in the immediate cutting zone. The basic concept to improve the drum water spray system was to utilize high-pressure (1,200 psi) inward-facing drum sprays to improve the dust knockdown efficiency of the spray system and confine the dust to the face area. This system would minimize the exposure of the shearer operator through dust avoidance and decrease face dust levels by suppressing the amount of respirable dust that becomes airborne. System Design In-mine tests were designed to provide information that would permit evaluation of the operation with different spray orientations and water spray pressures. This was achieved by comparison with a conventional baseline wet-cutting system consisting of 26 low-pressure bit sprays, located on the hit blocks to provide pick-point flushing. Total drum water flow was 60 gpm and was maintained continuously throughout all tests. The high-pressure inward-facing drum water spray system consisted of sprays located in each bit block, oriented 15° and 30° toward the face. The inward-facing water spray system was operated at either 800 or 1,200 psi.

Jan 1, 1989

By Zsuzsanna Zborovszky

Investigation of the discharge duration power and current relation required for ignition. The current and power amplitude-discharge time curve was found to flatten out over 3 ms. It is concluded that discharges having at least 3 ms power maximum are required for reliable testing of the ignition limit for resistive circuits. Investigation of the effect of molten cathode on the discharge duration and igniting ability of the discharge. The surface tension of the liquid metal causes a very fast separation and consequently a much shorter discharge duration than the solid electrode would have. The minimum discharge voltage effect overrides the effects of the temperature of electrode, material, or atmosphere. Investigation of the effect of different surface layers on the discharge duration. Oxides and sulfates were found to give significantly longer duration than the "clean" metal itself in most cases. The lowest ignition current was obtained with CdS04 coatings. Ignition was obtained with 0.7A at 30V, which is below the corresponding minimum igniting current obtained from the BASEEFA curve for circuits containing Cd, Zn or Mg.

Jan 1, 1977

By Leonard Obert

The various underground rooms in the Bureau of Mines Oil-Shale mine, Rifle, Colo., have been open for periods ranging from 3 to 5 years. During this time 3 roof falls have occurred; 1 was induced, and the other 2 were unintentional. The three roof falls are described in this report. Two causative factors are discussed -a time-dependent deterioration of the roof rock and an unfavorable system of jointing that occurred in the strata overlying the present roof horizon. Irrespective of cause, the operating life of any stoping area would have been short com-pared with the life of the roof (1 to 4 in the most unfavorable instance), if a high-production system of mining had been employed. The report is concluded with several recommendations that should be considered in planning future mining operations.

Jan 1, 1958

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By William J. Campbell

One of the principal objectives of the Bureau of Mines program for developing super refractory materials is to obtain fundamental data on the physical properties of refractory oxides. This particular investigation obtained accurate thermal expansion coefficients for alpha alumina and evaluated, critically, those coefficients with other published values. High-temperature X-ray diffractometer measurements, by the Bureau, showed that alpha alumina expands anisotropically with expansion parallel to the c axis approximately 10 percent greater than parallel to the a axis. Thermal expansion characteristics of four different alumina samples were determined up to 1,200° C.; the results are presented in both tabular and graphical form. The combined random and systematic errors in the measurements are considered less than 3 percent above 500° C, and approximately 2 percent at 1,000° C. No differences in expansion were observed between the samples or between the heating or cooling cycles.

Jan 1, 1961

By L. B. Pankratz

Present-day interest in the rare-earth elements and their compounds, for both metallurgical and ceramic uses, makes it highly desirable to accumulate basic thermodynamic data that can be applied to theoretical considerations of the processing of these substances. Such data still are seriously lacking. This Bureau of Mines paper reports the results of high-temperature heat content measurements of the sesquioxides of four rare-earth elements--europium, gadolinium, neodymium, and samarium--and of the closely related element, yttrium. The temperature ranges covered by the measurements are as follows: Monoclinic Eu2O3, 298°-1,802° K. Cubic Eu203, 298°-1,350° K. Monoclinic Gd203, 298-1,802° K. Cubic Gd203, 298°-1,550° K. Hexagonal Nd203, 298°-1,795° K. Monoclinic Sm203 298°-1,798° K. Cubic Sm203, 298°-1,149° K. Cubic Y203, 298°-1,799° K.

Jan 1, 1962