Search Documents

By G. Dale Coe, Will H. Coghill

The " periodic pincer " herein described fills a need for a device to control the rate of flow of a wet ore pulp through an orifice . Two uses of the periodic pincer to be discussed are on classifiers and on a wet ore feeder . Although the immediate necessity that brought about this device was for better operation of a miniature hydraulic classifier , in connection with an investigation of iron- ore concentration being conducted by the Federal · Bureau of Mines , with the cooperation of the University of Alabama , the device has promise of a wider field of application . In the iron - ore work , the need became so acute for a nonchoking , uniform - delivery classifier spigot that development of a suitable device was imperative .

Apr 1, 1944

By Sam S. Taylor, H. M. Smith

"INTRODUCTION In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas Produced with the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production must be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used.Although P.ir is a Cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case. The Petroleum Experiment Station of the United States Bureau of Mines at Bartlesville, Okla., has been interested in problems connected with air-repressuring for a number of years. Some time was spent in studying the so-called ""bad gas""--return,mixture of low fuel value. However, it appeared impossible to attack the problem successfully from this angle, and an approach was made through a laboratory--scale study of direct oxidation of crude oil."

May 1, 1934

By M. D. Carver

The purpose of this investigation was to determine the effects of variations in content (near the residual level) of the impurities aluminum, nitrogen, manganese, and copper on the corrosion rate in pressurized hot water and in pressurized steam of zircaloy-3, a zirconium-base alloy of 0.25 percent tin and 0.25 percent iron. Thirty-five 10-pound ingots were cast with the appropriate additions of impurity elements, and these were converted to wrought sheets. These specimens were then tested both in water and in steam. The analysis of the resulting data showed that in environments of either pressurized hot water or superheated steam, corrosion rates increased with increasing content of aluminum, nitrogen, or manganese, but were not affected by variations of copper. The effects of aluminum and nitrogen were found to be greater than the effect of manganese. INTRODUCTION At the request of the Atomic Energy Commission (AEC) in August 1956, the Federal Bureau of Mines, in cooperation with Bettis Plant of Westinghouse Electric Corp., began investigating the effects of certain impurity elements on the corrosion rates of zircaloy-3 in pressurized hot water and in pressurized steam. It was necessary to know these effects in order to set control limits on residual impurity levels in zirnaloy-3, intended for heat transfer service in the nuclear reactor of the pressurized water type. A factorial expert it was designed by Westinghouse statisticians. The Atomic Energy Commission provided raw zirconium sponge purchased from Wah Chang Corp. The Bureau's laboratory at Albany, Oreg., made material of different combinations of impurity levels and subjected the material to corrosion tests. This report will describe the work done at the Bureau laboratory and will show, quantitatively the effects of different residual levels of aluminum or nitrogen, or manganese or copper on corrosion rates.

Jan 1, 1961

By D. Harrington

Insofar as prevention of mine explosions is concerned, it is apparent that the coal-mining industry has profited but little from experiences during the past 15 years. The fact that explosions can be prevented if well-known preventive measures are adopted and conscientiously carried out appears to warrant the conclusion that many coal-mining people are indifferent to the hazards that may result in explosions. Although the principal burden of preventing explosions is upon the management, and much of the evident carelessness in failing to place in effect and to enforce suitable precautions, is assessable directly against management, the worker also has a very definite responsibility, and numerous explosions have resulted because of his failure to carry out his part in accepted principles of safety. The record of fatalities from mine explosions during the past 5 fiscal years has been anything but encouraging or about which coal-mining people can take pride; more men were killed by explosions (673) than were killed from the same cause during the preceding eight years combined (577). During each of the fiscal years 1942 and 1943, 152 fatalities resulted from explosions, compared to 163 during the fiscal year 1941, 206 in 1940, and only 16 in 1939.

Jan 1, 1944

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By John Nagy

To facilitate increase in the rate of coal production the Bureau of Mines conducted a study several years ago, on the basis of which the allowable charge limit for permissible explosives in single-hole blasting was raised from 1.5 to 3.0 pounds. Further demands for accelerated production led to consideration of multiple blasting in coal, a practice that is deemed hazardous and is not permitted by most States in this country. In multiple blasting, 10 to 20 pounds of explosive or more may be detonated in a coal face within a fraction of a second, which might result in blown-out or blown-through shots with possible ignition of gas or coal dust. As experimental evidence was lacking, in January 1949 an investigation was undertaken in the Experimental coal mine at Bruceton, Pa., principally to study and compare with single blasting the condi-tions under which simultaneous multiple blasting and particularly multiple short-delay blasting may be practiced without danger of igniting gas or coal dust in mines. The first report on this subject was presented at the last international conference of mine safety research. Since that time numerous additional experiments have been made; because of other pressing problems the work has been brought temporarily at least to a conclusion. This paper is the second report on the problem. It does not contain a detailed description of all test conditions and test arrangements, many of which were described 2 years ago in part 1 (now available as Report of Investigations 4868), but the conclusions are based on the entire study. A more complete review, which will incorporate data from the entire investigation, is being prepared as a Bureau of Mines bulletin. Up to the present time, short-delay blasting of coal in commercial mines has been introduced only experimentally in Washington and in a few mines elsewhere. If the system is adopted more generally, new problems may arise, and the study may have to be reopened.

Jan 1, 1952

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

By Wilder D. Foster

In the method used in the Health Branch of the Bureau of Mines for petro-graphic identification of the minerals in a rock, the sample is crushed, ground to a fine powder in a mortar, the powder is put on a slide, a drop of index oil and a cover slip are added, and the slide is ready for examination. The rock should be ground fine enough so that most of the particles consist of only one mineral, otherwise identification is difficult. Finally, the amounts of the minerals present in the sample are estimated to the nearest 5 or 10 percent. When quartz grains are mixed with some claylike minerals) of which by far the most common example is quartz and kaolinite in a shale, grinding in a mortar does not always separate the quartz from the kaolinite; instead, the quartz grains become coated with the kaolinite and are not visible, even after careful search. Talc acts Similarly, but muscovite and pyrophyllite do not. In evaluating the possible silicosis hazard of breathing dust from a shale, it is essential to be able to see and identify all of the quartz grains, as the other minerals present are relatively innocuous.

Jan 1, 1949

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

The NIOSH Office of Mine Safety and Health has released communication products about flyrock safety in the form of informational brochures, flashcards, and toolbox talk materials. Both the mining and construction industries are targeted with these helpful communication tools. These new products can be used as refresher training for employees and as introductory safety materials for onsite visitors.

Dec 1, 2006

By A. W. Fahrenwald

"About two years ago the Bureau of Mines, Department of the Interior, and the University of Idaho undertook an investigation of classification in its relation to table concentration of Idaho ores. The cooperation of the management of the Bunker Hill & Sullivan Co. in placing at our disposal their West Mill and facilities as desired, offered an unusual opportunity for studying the field of hindered classification in its practical and economic relation to table concentration.It has been shorn theoretically, and demonstrated experimentally, that ore products are more easily and economically concentrated on tables if the natural feed, consisting of various minerals and of all sizes of particles of each mineral, be classified or grouped into a series of products in which the mineral particles of greatest density are small in diameter relative to the diameter of the mineral particles of lesser density. Products in which the maximum difference in diameter of light and heavy minerals occurs are to be obtained only by true hindered settling classification. To our knowledge there has never been a really good hindered settling classifier used in practice and the present tendency seems to be to by-pass any attempt at such classification.After a careful study of the nature of hindered classification and of the requirements for hindered settling in practice, a classifier has been developed that takes fullest practical advantage of the widely known, but generally only meagerly understood, condition of hindered settling so well analyzed a number of years ago by Dr. Richards.The present paper presents briefly some of the more important practical results accruing through the investigation."

Jun 1, 1924

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different fields and regions as made by the Bureau of Mines Hempel method of analysis.4 Several of these reports include analyses of crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By R. E. Kennedy

The presence in air of combustible cases and vapors can constitute an extremely serious explosion hazard. This hazard is even greater when explosive mixtures are confined under high pressures, as the pressure can become tremendous immediately before the container is ruptured. Because of its interest in safety in mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and has published Its findings. 4/ The explosibility of ethane has been studied, and its limits of flammability have been determined and published. The development of secondary recovery methods of stimulating oil production has intensified interest in the effect of high pressure on the explosibility of natural gas-air mixtures. The limits of flammability of natural gas-air mixtures at pressures ranging from 50 mm. Hg to 350 p.s.i.a. have been determined and published. More recently, the limits have been determined at pressures up to 3,00C p.s.i. in mixtures of natural gas-air-nitrogen.

Jan 1, 1950

By Lulie H. Crump

Salient historical data on consumption of fuels and energy have been summarized by State and census district for the years 1960 through 1972. This Information Circular covers States east of the Mississippi, and Information Circular 8705 covers States west of the Mississippi. These data replace previously published compilations of energy consumption statistics by States and districts. Future annual studies are planned using the same Btu conversion factors applied in these two. Information Circulars.

Jan 1, 1976

By F. S. LOTT

Publication of the Bureau of Mines annual surveys of the capacity of petroleum refineries in the United States was suspended after the entry of the United States into World War II . The last published survey was that of January 1 , 1941 , released in April 1941 as Information Circular 7161 . The purpose of this publication is to provide comparable information with respect to crude - oil and cracking capacity on January 1 , 1947. No attempt is made at this time to bridge the gap in annual statistical series from the date of the last published survey to the present one . However , complete summary tables will be included in the succeeding survey for January 1 , 1948 .

Mar 1, 1948

By Kenneth H. Johnston

For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meetings of the Kansas-Oklahoma Waterflood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1960 spring tour of four waterflooding projects in Greenwood County, Kans. (fig. 1). Three of the projects produce oil from the Bartlesville sand, and one produces from the Cattleman sand. The Bartlesville-sand floods have been in operation from 4 to 12 years and have produced about 3,910,000 barrels of waterflood oil from the injection of approximately 64,715,000 barrels of water, a cumulative water-injected to oil-produced ratio of 17 to 1. The Cattleman- sand flood, which has been operating for 3-1/2 years, has produced about 842,000 barrels of waterflood oil from the injection of approximately 9,305,000 barrels of water, a cumulative water-injected to oil-produced ratio of 11 to 1.

Jan 1, 1960

By S. H. Ash

THE MAGNITUDE of the drainage problem of the anthracite industry in Pennsylvania's Western Middle field is realized when it is known that in 1951 nine pumping plants in this field pumped nearly 36 billion gallons of water to the surface. This is almost 68,000 gallons per minute pumped against an average hydrostatic head of 350 feet for that year alone. In 1948 over 20,000 gallons per minute was pumped by relay pumps against an average hydrostatic head of 265 feet. In addition to the water pumped to the surface, it is estimated that 15,000 gallons per minute overflows to the surface from underground pools in idle mines. The volume (second-feet) of water pumped and overflow water is almost 1;z times the, average mean flow of the Schuylkill River at Pottsville for the 8-year period 1944--51 (7, 13).4 Mahanov and Shamokin Creeks drain an area of 99 square miles in the Western Middle field, and all surface drainage in this area must traverse some part, of the coal measures before entering these streams. On the basis of 46.03 inches of rainfall (the weighted average of 6 recording stations for 1948), the runoff from the drainage area during that period was 51 billion gallons, approximately 1 times the volume of water pumped by all mine-pumping plants in the Western Middle field. In other words, because of the pervious strata overlying the mine workings, approximately two-thirds of the total runoff in the drainage, area becomes mine water tributary to the pumping plants.

Jan 1, 1953

By J. A. Woolf, E. S. Leaver, N. K. Karchmer

"In the cyanidation of silver ore, the need of oxygen is well recognized. Various methods have been introduced for supplying the oxygen. In usual practice, air is the source of oxygen and the methods of application are mechanical.This article gives the results of touts made to show the rate of dissolution of silver from each of the common silver minerals in cyanide solution, under conditions similar to those used in the practical recovery of silver from its ores. The effect of oxygen in aiding the dissolution of the silver from each mineral is also shown by a comparison of the methods of supplying the oxygen. Oxidation by preliminary roasting (500°C.) of each mineral sample gives the maximum extraction of the silver by treatment with cyanide.Each silver mineral5 used in these experiments was as pure as could be obtained from the mineral dealer. In their natural occurrence, silver minerals are not usually free from mineral impurities. They are usually closely associated with other minerals often forming, a complex mixture. The form of crystallization, the proportions, and properties of the diluent that incases or has been dispersed with the silver mineral may decidedly affect the dissolution rate of the silver from each mineral. While the following results should aid in the cyanidation of silver ores, each ore should be studied from the basis of the form and condition of the silver that is to be recovered.All the tests reported in this article were made on synthetic samples, prepared by mixing the particular silver mineral with clean sea sand. Each mineral was ground in an agate mortar to pass 100-mesh before mixing with the sand which had previously been ground in a porcelain pebble mill to 100-mesh. Such proportions of each mineral and the sand were used as to give a head assay of approximately 20 ounces of silver per ton to the synthetic sample.Agitation was carried on in stoppered bottles approximately one-third full of pulp, method apparently supplied all the atmospheric oxygen that would be taken up by the solution under usual conditions, because tests conducted in open bottles did not show increased recovery,"

Jan 1, 1931

By Forrest T. Moyer

Injury experience in the coal-mining industry was worse in 1965 as both the frequency and severity rates of injuries increased 2 and 6 percent, respectively, over comparable data for 1966 (tables 1-8). The retrogression in the safety record during; 1965 resulted frog the less favorable record at bituminous-coal mines, which more than offset the improved injury experience at anthracite mines. The 259 fatal and 11,138 nonfatal injuries occurred at a rate of 45.77 per million man-hours of exposure and resulted in a severity rate of 8,960 days lost per million man-hours. Although the number of fatalities was the second lowest annual total in the recorded history, it was 17 higher than in 1964. At anthracite operations the total of 6 fatalities in 1965 was the lowest annual figure in statistical history. The annual numbers of nonfatal injuries at ill coal mines and the resulting rates of occurrence have varied little in the past 5 years (table 1). The total days lost from all injuries rose from 2.1.3 million in 19b4 to 2.23 million in 1965 (table 5). Fatal and permanent total injuries, with a standard time charge of 6,000 days each, accounted for 1,650,000 days; Permanent partial injuries, 191,932 clays; and temporary total disabilities, 383,911 days. The severity rate for fatal injuries was 6,241, 8 percent higher than in 1964, and the nonfatal severity rate of 2,718 days lost per million man-hours was 2 percent higher than in the preceding year. The average severity of permanent partial injuries ire; 730, or 48 days fewer per injury than in 1964. The average days lost for each temporary total injury was 36 days in each year.

Jan 1, 1968