Search Documents

By George A. Burrell, Frank M. Seibert

The Bureau of Mines, as part of its designated duty of investigating the causes of mine accidents, is conducting at its experiment station in Pittsburgh, Pa., a study of mine gases. Some of the work already done in connection with this study is outlined below. A large number of mine-gas samples have been collected under normal conditions in returns and in splits, and at other points in the ventilating current, also at the face, in the goave or gob, in unventilated places, and wherever the air was still. Samples have also been obtained under abnormal conditions, as after explosions and while mine fires were in progress, or from sealed areas behind stoppings and darns where the air had been stagnant for some time. Chemical changes in the composition of mine atmospheres during mine fires have been studied," and conditions peculiar to certain mines have been investigated. The question of the effect of a change in atmospheric pressure on the escape of gas (methane) in coal mines has been studied. Explosives have been fired in both coal and metal mines, and samples of resulting gases have been collected to ascertain the degree to which these gases vitiate the air. A series of samples in mines where gasoline locomotives were being used have been examined in order to ascertain the degree to which the exhaust gases from such locomotives foul the mine air. Experiments have also been performed in regard to the relative effect of carbon monoxide b upon men and small animals. A preliminary report relating to the inflammable gases in mine air has been published. Full reports of the results of the investigations outlined above will be published as soon as all the necessary data have been gathered. The first part of this report deals with the methods used by the bureau in the collection and examination of the various mine gases; the latter part discusses the bureau's methods of sampling and examining natural gas.

Jan 1, 1913

By Elizabeth A. Johnson

The vaporization thermodynamics of the aluminum-silicon carbides Al4SiC4 and Al8SiC7 were studied by the Bureau of Mines over the temperature range of approximately 1,500 to 1,700 K. Vapor pressures were measured by a Knudsen effusion-mass spectrometry technique in which powdered samples were effused from graphite crucibles through small orifices. For each compound, a total of six orifice diameters was tested to verify equilibrium within the cell. Aluminum, mass number 27, was the only vapor species detected over the range 4 to 200 amu. Experimental results are based on the following equations for incongruent decomposition: A14SiC4(cr) - 4A1(g) + SiC(a,hex) + 3C(gr); Al8SiC7(cr) - 8A1(g) + SiC(a,hex) + 6C(gr). The observed vapor pressure-temperature relationships determined with a cell orifice area of 2.0 x 10-3 cm2 for Al4SiC4 and 1.81 x 10-3 cm2 for A18SiC7 are the following: Log P - (-18,682/T) + 12.476, for Al4SiC4 (1,550 to 1,643 K) and Log P = (-19,308/T) + 12.421, for Al8SiC7 (1,526 to 1,784 K), with P in pascals and T in kelvins. Third-law analysis of the data provided the following heats of formation: A14SiC4 ?H at 298.15 K - -50.0 kcal/mol and A18SiC7 ?H at 298.15 K - -92.1 kcal/mol.

Jan 1, 2011

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made an the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By D. W. Bridges

Solvent extraction has become important in recent years as a unit process in extractive metallurgy. The flexibility and simplicity of the technique have attracted widespread attention, and numerous papers describing actual and projected metallurgical applications have been published. However, differences in terminology, procedure, objectives, and standards, as reflected in reports by different operators and investigators, have sometimes made appraisals and comparisons difficult. Consequently, a need appeared for n series of basic reports on the subject. This Bureau of Mines Information Circular is the first of such a series. It deals with the status of solvent extraction in metallurgy, as well as with the rudiments and terminology of the unit operation. In analytical chemistry, extraction of molecular species from aqueous media by immiscible organic solvents has been used for many years to separate and determine chemical elements (61).4 Complex chlorides of iron and other metals are readily soluble in ethers and ketones, as are the nitrates of uranium and thorium. Most metals are extractable as complex salts of some organic reagent, such as dithizone, 8-hydroxyquinoline, or cupferron.

Jan 1, 1962

By James A. Browning

Conventional flame channelling operates continuously at over 120 db --flame-drill channelling at a maximum of 95 db. The latter process was developed under this program. Individual drill holes are spaced to leave narrow rock webs. Sound and dust passing from the hole are effectively treated by a muffler and water injection.

Jan 1, 1980

By M. M. Ayoub

With a return to coal as a major energy source for many companies, more emphasis is being placed on recovery of coal from areas that were formally considered uneconomical to mine. Increasing emphasis is being placed on production from low coal (seam height 48 inches or less) as high coal seams are depleated. Mining in restrictive spaces requires unusual work postures that can turn easy jobs into demanding ones. The objectives of this research were: (1) to evaluate the job demands associated with low coal mining, (2) to survey the anthropometry, strength, and aerobic capacity of low coal miners to determine if they differ from the U. S. population, and (3) to recommend, on the basis of available information, optimal job and work station design for low coal mining. This research effort was supported by the U. S. Bureau of Mines. The male and female anthropometry with the exception of weight and circumferential dimension, was quite similar to the comparison population. Back strength for male and female miners was significantly lower than the industrial worker population. This can be one of the contributing factors of low back problems in mining. Shoveling, timbering, and helpers tasks were physiologically demanding activities. However, due to the frequent stoppage of work, adequate rest was usually available. If work stoppage is corrected, then better work/rest schedules are essential.

Jan 1, 1981

By Richard D. Smith

The Bureau of Mines evaluated the emission control methods, including the capital investments and operating cost, necessary for further reducing lead levels in ambient air at the Glover, Herculaneum, and Buick smelter-refineries in Missouri and the East Helena, MT, smelter. The U.S. Environmental Protection Agency (EPA) has proposed more stringent lead in ambient air standards than those currently in effect. This report presents theoretically achievable lead emission reductions and estimated capital and operating costs. Lead emission inventories theoretically can be reduced from 1985 levels by 2,421 lb/d at the three Missouri operations by containing and filtering fugitive emissions within structural enclosures and baghouses. The aggregated capital and operating costs in 1986 dollars using conventional environmental and workplace technologies are estimated to be $250,014,100 and $18,507,800, respectively. Estimated total incremental cost is $0.063/lb as refined lead. Additional regulatory costs attributable to Occupational Safety and Health Administration (OSKA), U.S. Department of Labor, workplace standards are included since proposed environmental controls may otherwise degrade workplace conditions. Continuous drossing is evaluated as an alternative to conventional OSHA controls. Substituting continuous drossing for conventional work- place technology results in an estimated aggregated capital and operating costs of $258,344,800 and $15,719,600, respectively. Estimated total incremental cost is $0.062/1b as refined lead. For comparison, the average open market price of refined lead during the first quarter of 1986 was $0.184/lb.

Jan 1, 1987

By Jr. Boyle

This report analyzes the availability of chromium in the form of ferroalloy products (high-carbon and low-carbon ferrochromium and ferrochromium-silicon) and chromite products (metallurgical, chemical, refractory, and foundry sands) in market economy countries (MEC's). A total of 873.5 Mmt of in situ material, containing 202.5 Mmt of chromium, in 10 MEC countries was analyzed for availability as of the January 1989 study date. Extraction and beneficiation of this in situ material would result in 475.4 Mmt of marketable chromite products. As analyzed, 288.5 Mmt of these chromite products would be available for export or for internal chemical and refractory use and 186.9 Mmt would be smelted in-country to produce 74.3 Mmt of high-carbon ferrochromium, 3.9 Mmt of low-carbon ferrochromium, and 2.0 Mmt of ferrochromium-silicon, all available for export. A network flow model, which includes centrally planned economy countries (CPEC's), was also constructed to analyze world chromium supply and demand interactions for the period 1986 through 1994 and to address a hypothetical North American embargo on direct imports of all South African chromium products beginning in mid-1990. The model shows capacity constraints developing in the MEC high-carbon ferro chromium industry in 1987 and a possible subsequent overreaction by the industry in terms of new capacity additions. The results suggest that sufficient chromium is available to North America should an embargo on direct imports from South Africa be imposed by its governments. However, the effect on export revenues in South Africa is relatively small, and timely increases to world ferrochromium, chemical chromite, and foundry sand chromite capacities would be required.

Jan 1, 1993

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

By P. G. Guest

MANY of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed in operating and anesthetizing areas. When ether was first introduced, candles,5 gaslights, and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions-many of them fatal to patients-have been attributed, with good reason, to sparks from static electricity.

Jan 1, 1953

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By Michael G. Zabetakis

THIS is a summary of the available limit of flammability, autoignition, and burning-rate data for more than 200 combustible gases and vapors in air and other oxidants, as well as of empirical rules and graphs that can be used to predict similar data for thousands of other combustibles under a variety of environmental conditions. Specific data are presented on the paraffinic, unsaturated, aromatic, and alicyclic hydrocarbons, alcohols, ethers, aldehydes, ketones, and sulfur compounds, and an assortment of fuels, fuel blends, hydraulic fluids, engine oils, and miscellaneous combustible gases and vapors.

Jan 1, 1965

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

By Sidney Katell

This report, covering the period January 1969 through December 1969, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the 11th in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost. Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal Mining and Processing.

Jan 1, 1970

By Karl E. Starch

This Bureau of Mines report is a background study of severance taxes on mineral production. The rates, bases, and other features of State severance tax legislation as of March 1978 are presented, as are the amounts of State severance tax collections for fiscal year 1977, Some statistical comparisons between severance tax collections, total State tax collections, and total value of mineral production in the States involved are presented to portray the relative importance of severance taxes both in State tax revenue systems and in mineral industry revenues. A general discussion of the purposes and principles of taxation, the unique nature of a mining enterprise, the various types of taxes imposed on mineral production, and the character and rationale of the severance tax and its impacts on mining firms sets the severance tax in perspective. A bibliography of materials on the severance tax is included.

Jan 1, 1979

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 20 or 30 ampere leak, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1974

By H. S. Caldwell

A magnesium-base incendiary alloy, containing about 20 percent cadmium, 4 percent aluminum, and 0.5 percent zinc, was investigated in a series of vacuum-distillation experiments to determine the feasibility of recovering magnesium and cadmium as refined metals. Alloys prepared in the laboratory and actual bomb-casing alloy were studied at temperatures of 550° to 750° C. and pressures of 100 to 150 microns. Simple distillation and fractional distillation methods were only partly effective in separating the cadmium and magnesium. They were separated satisfactorily, however, with a special vapor baffle designed to condense the metals selectively. Magnesium and cadmium products were 99 percent pure and together comprised 82 percent of the total condensate. About 17 percent of the condensate was intermediate-grade alloy that could be recycled with new charge and contained about 70 percent magnesium and 30 percent cadmium.

Jan 1, 1959

By William H. Schiffbauer

The Bureau of Mines has developed a passive encoder for range knobs, a device that automates the task of obtaining the range settings from devices or instruments to be input to microcomputers. It is easily constructed and installed and will not disrupt the device to which it is being attached. It consists of a custom knob and a small printed circuit board that has light-emitting diodes and magnetic reed switches attached. A ribbon cable connects it to a microcomputer. This encoder eliminates one source of human error in an automated process.

Jan 1, 1983