Search Documents

By Christopher Van Dyke, Knox Van Dyke, Lixin Wu, Jaime Gutierrez

"I. INTRODUCTION(SILICA, THE LUNG, INFLAMMATION, AND FIBROSIS)Inhalation of respirable-size silica (0. I to 5 µm in diameter) deposits the particles in the deep spaces of the Jung where oxygen is exchanged. The resulting pattern of inflammation is substantially different compared to that observed from other inhaled substances such as carbon, polystyrene titanium dioxide etc. 1 Following the inflammatory reaction the body attempts to isolate the damage by walling off the area via fibrosis. 2 The unique nature of the inflammatory response to silica makes it logical to infer that fibrosis is a later-stage manifestation of the initial inflammatory damage. In addition to the inflammation extensive lysis and cellular death particularly to macrophages and neutrophils, can occur, depending on the dose of silica.' The ingestion of significant amounts of silica by macrophages and neutrophils produces an inflammatory sequence which activates the lipoxygenase pathway of arachidonic acid metabolism and produces platelet activating factor (PAF) and leukotrienes (LT).4·5II. CALCIUM IONOPHORE MIMICS SILICA TOXICITY IN VITROPhagocytic cells exposed to silica in vitro produce PAF and LT. This response is reminiscent of phagocytic cells exposed to the calcium ionophore (A23 l 87) in the presence of ionic calcium.6-8 A23 l 87 forms a complex with free ionic calcium which passes through cellular membranes, thus transporting calcium inside the cell. The increased intracellular calcium concentration triggers the production of small amounts of prostaglandins large amounts of LT. PAF and. depending on dose cellular death (see Figure 1 ). Could silica cause LT production and cellular death by a similar mechanism? How could silica - an inert solid - act in a similar fashion as a soluble stimulant? Clearly the negative SiO2 and OH- surface of silica can bind calcium ions9 and therefore could theoretically act as a solid-state ionophore releasing bound calcium inside of cells following phagocytosis."

Jan 1, 1998

By J. D. Davis

"Introduction.Sixty years ago, M. Berthelot found that ethylene could be selectively absorbed from gaseous mixtures by concentrated sulphuric acid, and that the compound formed by the chemical union of the gas and acid was readily decomposed by heating with water, yielding ethyl alcohol. Only within the last few years has there been any attempt to make use of this discovery technically.Bury*, working in England at the Skinningrove Iron Works and on a commercial scale, developed a technical method for converting, the ethylene of coke-oven as into alcohol. With a gas containing less than 3 per cent of ethylene, he obtained a yield of 1.6 gallons of alcohol per ton of coal carbonized.De Loisy** perfected a technical method for treatment of coke-oven as for alcohol. Evidently this work was carried out on a semi-commercial scale. His method is based on the use of catalytic agents for hastening the absorption of ethylene by sulphuric acid. He uses part of the spent acid for drying the gases and pact for the manufacture of ammonium sulphate. Excess acid is reconcentrated by waste heat. Others have worked on the problem, but so far there has been no large recovery of ethylene from coke-oven gases. The chief difficulty seems to lie in the low efficiency (about 50% of methods and tae relatively low concentrations of ethylene in the gases treated. Gas from Trent amalgam*** contains much larger percantages of ethylene than does coke-oven gas, as Will presently be shown, and if it should ever prove practIcal to treat industrial ;as for alcohol, this gas would offer attractive possibilities,* Bury, Ernest, Ethylene as Alcohol from Coke-Oven Gas: Gas Journal' Vol. 148, D. 30, 1919, pp. 718.** DC Loisy, M.E., Sur un procede' industrial de fabrication syntlotique de l'alcool et de l'ether a partir des gaz de distillation de la houil Comp Rend, vol. 170, Jan. 1920, p. 50-3.*** A paste consisting of approximately part oil such as that obtained as for cleaning coal. See Perrott. in cleaning coal, Chem 3 parts finely pulvarized coal and 1 final product in the Trent, process StJ, and Kinney, S.P. The use of oil Vol. 35 August 3, 1921, p, 183.. & Met."

Nov 1, 1922

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

By Susan M. Moore

The objective of this study was to evaluate the circumstances leading to fall from equipment injuries in the mining industry. Method: The 2006 and 2007 Mine Safety and Health Administration annual injury databases were utilized for this study whereby the injury narrative, nature of injury, body part injured, mine type, age at injury, and days lost were evaluated for each injury. Results: The majority of injuries occurred at surface mining facilities (~60%) with fractures and sprains/strains being the most common injuries occurring to the major joints of the body. Nearly 50% of injuries occurred during ingress/egress, predominately during egress, and approximately 25% of injuries occurred during maintenance tasks. The majority of injuries occurred in relation to large trucks, wheel loaders, dozers, and conveyors/belts. The severity of injury was independent of age and the median days lost was seven days; however, there was a large range in severity. Impact on industry: From the data obtained in this study, several different research areas have been identified for future work, which include balance and stability control when descending ladders and equipment design for maintenance tasks.

Jan 1, 2009

By Thomas J. Fisher, John J. Sammarco

This report (System Safety 2.1) is the second in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 [IEC 1998a,b,c,d,e,f,g] and other recognized standards. The scope is “surface and underground safety mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system.

Jan 4, 2001

By James L. Konchesky

Crushed coal, consisting of a wide range of sizes, was effectively blended by recycling it through a bin equipped with a particle distributor. Vertical blending was accomplished by simply recycling the coal; it was not significantly influenced by the horizontal blending that was achieved by the distributor. The method was effective, even though the coal was wet and possessed poor flowing characteristics. Recirculation appears capable of providing uniform blends of solids that can be more efficiently processed. Recirculation also appears useful, preceding packaging operations, to insure for blending of solids into specification products. Continuous measurement of the bulk density of the coal by a gamma ray meter proved to be an effective monitor of vertical blending effectiveness.

Jan 1, 1972

By E. D. Regad, W. E. Wallace, V. Vallythan, V. Castranova, P. Hathaway, F. H. Y. Green, M. J. Keane

"Abstract—Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modelled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiological saline. Lecithin adsorbs to the dusts upon incubation at 3TC and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defence system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modelled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica haemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin haemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate that most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in the same time; that which is. results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.INTRODUCTIONERYTHROCYTE HAEMOLYSIS and pulmonary macrophage enzyme release assays show quantitatively comparable high cytotoxicities for both silica quartz and kaolin respirable sized dusts (BROWN, et al., 1980; DANIEL and LE BOUFFANT, 1980.) This contrasts with the strong potential for respirable quartz dust to induce pulmonary fibrosis and the much more limited potential of kaolin dust to do the same (MORGAN and SEATON, 1975).In an attempt to understand this anomalous situation, assays were performed on quartz and kaolin dusts incubated with dipalmitoyl lecithin emulsified in physiological saline, to simulate the initial contact of a respired dust with the pulmonary alveolar hypophase. The ability of kaolin dust to adsorb dipalmitoyl lecithin from physiological saline has been quantified (WALLACE, et al., 1975). Such lecithin treatment suppresses the cytotoxicity of both silica and kaolin to background levels (WALLACE, et a1.,1984).Surfactant coated detoxified dusts should then be phagocytised by pulmonary macrophages, incorporated into a macrophage secondary lysosome and exposed to hydrolytic lysosomal enzymes. Among these is phospholipase A2, which hydrolyses diacyl lecithin to lysolecithin. This was modelled by incubating lecithin treated dusts with phospholipase A2 in vitro to determine if the enzyme can digest the dust-adsorbed lecithin, and if the retoxification differs between the two dusts in a manner which might distinguish their pathogenicity."

Jan 1, 1988

By Stephen A. Swan

Bureau of Mines research has not included analyses of mining dredge safety since 1948. Because of the increasing use of dredges, 63 fatal accidents and several hundred nonfatal injury accidents involving dredges were examined. Also, 31 working dredges and 3 dredge manufacturers were visited to acquire qualitative information. Drowning accidents represented 59 pct of the fatalities and are delineated in detail. Also, countermeasures against other hazards are discussed.

Jan 1, 1985

By H. A. Watson

The introduction and use of synthetic materials in various applications may lead to potential hazards from toxic, gaseous, decomposition products if these materials are subjected to conditions abnormal to their intended use, such as high temperatures or burning from accidental causes. This report covers an investigation of such possible hazards from toxic gases produced by the burning or thermal decomposition of some low-density, expanded, synthetic materials, three of which consisted of polyvinylchloride and one of acrylonitrile. In the production of certain expanded plastic materials, Chemical blowing agents frequently are used to produce a cellular structure. One of these blowing or foaming agents contains azo-bis-isobutyronitrile, which is designated in this report as PN. Information indicates that a product of decomposition of this blowing agent, formed in the blowing operation, is tetra-methyl-succino-nitrile, designated as TSN, Which is significantly toxic. Decomposition of the blowing agent, with release of its azo nitrogen, is represented by the following reaction:

Jan 1, 1951

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By J. B. Littlefield

The term "konimeter" is used generally to designate a type of dust-sampling instrument that collects the dust from a small volume of air by impingement on a glass plate prepared aced with an adhesive film. The konimeter was first developed by Sir R. N. Kotze about 20 years ago and was followed a few years later by the circular-type konimeter, by which a number of samples may be collected on a glass disk. The present discussion will be confined to the circular type, as it is used most. Various techniques have been developed for using the konimeter, and many materials, such as petrolatum, mineral oil, and glycerine jelly, have been used in preparing the adhesive film. In South Africa, Australia, and Canada, where the konimeter has been employed most widely, dust samples are treated by ignition and washing before being counted. In Canada the dust samples are collected on a disk of special heat-resistant glass prepared with a film of mineral oil; the disk is then heated to a dull cherry-red in a muffle-furnace to remove the film and organic matter, cooled, and washed with a few drops of 50-percent hydrochloric acid followed by distilled water and alcohol, and then heated again to remove residue left by evaporation of the alcohol. After this treatment, the dust samples are counted under a magnification of 150 diameters with dark field illumination.

Jan 1, 1938

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.5 and 3 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year product Lon period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 Indexes. Initial capital investment is $33.8 million for the 1.5-MM-tpy mine and $61 million for the 3-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $52.5 and $94.2 million, respectively. These figures translate into total capital investments of $34.87 and $31.31 per ton of annual production. Assuming a desired 15-percent discounted cash flow rate of return, with Federal income taxes at 50 percent, the required selling prices would be $12.06 and $10.94 per ton for the 1.5- and 3-MM-tpy mines.

Jan 1, 1976

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

By Richard D. Graves

Pitch from low-temperature carbonization of bituminous coal was hydrogenated at cracking conditions in a continuous bench-scale unit to produce low-molecular-weight oils and tar acids. The pitch contained 15.6 pct benzene-insoluble material, 4.0 pct hexane-soluble oil, and 80.4 pct asphaltene by weight. At 475° C, 7,500 psig, and 1.5 hours residence time, hydrogenation products, based on the weight of pitch, were about 36 pct oil boiling below 325° C, 24 pct hexane-soluble heavy oil, 17 pct asphaltene, 1 pct benzene insolubles, and 12 pct hydrocarbon gases. The yield of tar acids boiling below 250° C was 4.3 pct, and the yields of C6 to C8 paraffins, naphthenes, and aromatics were each less than 1.0 pct. The yield of tar acids was within the range of yields obtained by hydrogenation or high-temperature carbonization of bituminous coal (2 to 5 wt pct). Yields of oil boiling below 325° C increased with increased residence time or temperature. There was little or no effect of residence time on yields of alkali- soluble material which contained tar acids. Yields of hydro-carbon gases increased markedly with an increase in temperature from 475° to 500° C. Lowering the hydrogen pressure to 4,500 psig resulted in yields similar to those obtained at 7,500 psig.

Jan 1, 1962

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By Howard F. Puariea

This paper is one of a series describing methods and costs of recovering sand and gravel from alluvial deposits in the United States and deals directly with the methods employed by the Portland Gravel Co. in operating a clamshell dredge on the Willamette River near Portland, Oreg., and a pump dredge on the Columbia River near Vancouver, Wash. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs may in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By G. St. J. Perrott

Through the development of manufacturing processes whereby ethylene glycol can be made on a large scale; ethylene glycol dinitrate is now being used in high explosives (dynamites and permissible explosives) by some manufacturers as a low-freezing ingredient of the "explosive oil" instead of such compounds as nitropolyglycerin and nitrosubstitution compounds. The amount of ethylene glycol dinitrate being used constitutes 25 to 50 per cent of the oil. The purpose of this report is to give the results of toots, to determine the effect on the safety and physical properties of permissible explosives of subsituating 25 peg cent of ethylene glycol dinitrate for an equal amount of nitroglycerin or a mixture of nitroglycerin and nitropolglycerin.

Jan 1, 1929

By N. S. Dalal, X. Shi, V. Vallyathan

"Correlated spectroscopic and cytotoxicity measurements were made on newly crushed silica to find whether the fracture-induced, silicon related (Si-0· or Si· type) free radicals play a direct role in the mechanism of hemolysis by silica particles. The free radical content of the silica particles was controlled through the radical decay, thermal annealing, and boiling processes, and was followed with electron spin resonance spectroscopy. Portions of the same sample were evaluated for their hemolytic potential, employing sheep erthyrocyte and optical absorption techniques. The results indicate little, if any, correlation between the amount of the silicon-based radicals and the hemolytic potential of the fresh dusts, but these or related radical sites might be contributors to silica cytoxicity and fibrogenicity via peroxidative pathways .INTRODUCTIONIn an earlier convnunication (1.) from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates free rad;cals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubin; et al.(2) have also reported the detection by electron spin resonance (ESR) of the formation of SiO· and Si·-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum (10-10 torr) (3) and subsequent exposure to air (3), and to other gases (4), these radicals were identified (2) as being formed by the hemolytic cleavage of the Si-0-Si bonds and the reactions of the Si· and SiO· ,radical with atmosphere. Fubin; et al. (2) also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anea (5) had reported that lipid peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radical studies on a given Quartz dust sample have been reported, except for some earlier work from our laboratory (1,6,7). We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radical measurements on a freshly made quartz dust. The dust’s free radical content was measured using ESR spectroscopy while its cytotoxicity poteni1al was estimated via hemolysis. Hemolysis was employed as the tox1c1ty test because it 1s a widely used method for estimating the potential of a dust for disrupting the cell membrane (8). The f1brotic potential was followed.by measuring the dust-induced lipid perox1dat1on. us1ng linole1c ac1d as a model lipid. As discussed below, the results obtained suggest new clues.to the mechanism of the Quartz-related cytotoxicity and fibrogenicity."

Jan 1, 1988