Search Documents

By W. T. Abel

The Bureau of Mines tested 48 materials for their ability to absorb H2S from hot simulated producer gas (1,000°-1,500° F). The material found best from the standpoint of absorption capacity, durability, and amenability to regeneration was sintered pellets of 75 percent fly ash-25 percent Fe203. The performance of this absorbent under simulated and actual conditions is described. The effect of absorbent composition, absorbent temperature, steam content of the gas, and tar vapors and dust in producer gas is discussed.

Jan 1, 1974

By Uldis Jansons

This report evaluates the economic Mining feasibility of four selected mineral deposit types that can be anticipated to be found in (d)(2) lands in the western Brooks Range, Alaska. The major assumption made for this study is the availability of a rail system for transporting equipment and concentrates for the base metal mines. Commodity prices used are those in existence in July 1976. Mine models were established based on known deposits and then evaluated. A lead-zinc-silver-barite deposit for which grades were available but ore reserves were assumed would require approximately 25% higher ore grades or higher metal prices to yield a 15% discounted cash-flow rate of return an the investment if mined at a rate of 10,000 tons per day open pit methods. Large copper-zinc mineral deposits could be mined economically at rates either of 5,000 tons per day underground or 10,000 tons per day by open pit methods. A high-grade copper deposit require a copper price of over one dollar ryes pound to yield an economic profit to be mined at 2,000 tons per day by underground methods. A small high-grade gold underground mine would require a gold price of about $295 per ounce to yield a 20% discounted cash-flow rate of return on investment if all new mine equipment were used and if existing labor rates were paid: Enterprising mining groups operating as partnerships might be able to operate this mine profitably at a gold price of about $152 per ounce, perhaps slightly less.

Jan 1, 2012

By George S. Rice, Li C. Ilsley.

A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details: "The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all .appaarances, passed down the shaft causing disruptive disohalges at certain points between the guides and the winding rope, Tending the latter at two places situated respectively 228 feet and 278 feet frem the surface, The distance between the winding rope and the side of the shaft was 6 feet 4 inohes, indicating a spark gap;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft."

Feb 1, 1920

By S. R. Borrowman

Physical beneficiation, leaching, and solvent extraction investigations were made to recover a high-grade thorium oxide product from Bald Mountain, Wyo., conglomerate. The monazite in the Bald Mountain deposit contains 8.8 percent Th02 and, therefore, is higher in thorium content than the usual domestic or foreign monazite. A sample of composited drill cuttings for the study contained 4.3 pounds of monazite per ton of are. The work showed that the monazite, although unusually fine grained and friable, could be concentrated by tabling and magnetic treatment to yield a product assaying 5.65 percent Th02 with a recovery of 61 percent of the thorium. Subsequent decomposition of the concentrate by treatment with sulfuric acid and solvent extraction of the resultant solution with a primary aliphatic amine yielded a thorium oxide product of 99-percent grade.

Jan 1, 1962

By Jeffrey Kohler, John J. Samrnarco, Thomas Novak, Lloyd Morley

Equipment control functions that were once hardwired are being implemented with software and very large scale integrated (VLSI) devices. Often this transition has resulted in increased flexibility, improved quality, and decreased costs. At the same time, it has created new concerns and challenges concerning worker safety. The visible and well-defined ladder diagram for relay-logic has been replaced by program in which the exact outcome for varied inputs can be more obscure. In the coal mining industry,-efforts to automate longwall mining systems hove resulted in semiautonomous machines operating within the same space as workers This paper describes an effort initiated by the National Institute for Occupational Safety and Health (NIOSH to identify the safety rules related to the use of processor-controlled equipment in mining. Specific findings in the areas of human factors, hardware, and some safety are presented in this paper, and a brief description of a plan to address identified weaknesses is given.

By John H. Soule

"Although known since 1902, the Capitan iron deposits have not been mined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-45, visited the property; as a result, preliminary sampling of the property was done in 1943.3/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944.4/ Equipment available at that time was limited in the depths that could be reached; and, as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.The following sections note the location and accessibility of the deposits and mention the physical features, climate, labor and living conditions. Property and ownership are outlined, the history and production of the property stated briefly, and the ore deposits are described. The work done by the Bureau of Mines is explained and supported with maps, sections, and assay logs.From March 1, 1944, to June 1, 1944, 179 wagon-drill holes totaling 3,490 feet and 4 test pits totaling 75 feet were completed, and from November 1947 to February 1948 seven churn-drill holes totaling 2,488 feet were drilled and sampled. Metallurgical tests are summarized and referenced.With respect to this report, special acknowledgment is due to J. H. Hedges, chief, Tuscon, Ariz., Branch, Mining Division, and to W. R. Storms, engineer in-charge of the Silver City, N. Mex., field office. Acknowledgment also is due to J. Bruce Clemmer, chief, Tuscon Branch, Metallurgical Division, for analyses done in the last phase of this project, and to Dr. Vincent Kelley of the Federal Geological Survey for his cooperation during this work.The Capitan iron deposits are in secs. 10, 11, 13, 14, and 15, T. 8 S., R. 14 E., central Lincoln County, N. Mex., as shown on figures 1 and 2. The only known large deposit upon which the Bureau did development work lies around the common corner of secs. 10, 11, 14, and 15, as shown in figures 2 and 3, and just southwest of and in the foothills of the Capitan Mountains. This range of mountains trends east and west. The elevation of the highest peak is 10,205 feet.The deposits are reached by traveling on State Highway 48 from Capitan north for 4 miles, to a point just inside the Lincoln National Forest fence and thence due east over a poor dirt road for 1.2 miles. Just over a small wooden bridge, the left-fork is taken, and the poor road is followed to the deposits, a further distance of 1.1 miles (see fig. 1). This road follows the fence to and through the Davis ranch. All the roads from Capitan to the deposits are dirt roads but are impassable only for short periods during and after heavy rain or snow."

Aug 1, 1949

By Syd S. Peng

The design of retort interchamber pillars is important in determining surface stability over in situ retort mines and to the health and safety of miners, particularly with respect to possible escape of heat and toxic gases from retort chambers. Stress distribution in retort interchamber pillars, roof, and floor was examined with the aid of linear, finite-element analysis using data from experimentally determined mechanical properties. Properties determined included elastic moduli, strength, and creep constants in laboratory tests on core covering a 100-foot depth interval in the oil shale from the Piceance Basin in Colorado. The most critical stress concentration was found in the rib side of the interchamber pillar at a height above the floor line of 1.25 times the width. Guidelines for pillar design that consider pillar strength, creep, and retorting temperature effects are proposed.

Jan 1, 1981

By D. E. Hirsch

The Bureau of Mines has developed a systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling (350° to 550° C) distillates of crude oils. Isothermal and molecular distillation were used to prepare the 370° to 530° C distillate of Recluse, Wyo., crude oil. The distillate was separated into fractions by chemical treatment, silica-alumina gel adsorption, and gel permeation chromatography (GPC). The fractions were analyzed by use of GPC correlations and mass and nuclear magnetic resonance (NMR) spectrometry. The increased knowledge of petroleum composition obtained from the data will contribute to improved petroleum processing and utilization and energy conservation.

Jan 1, 1974

Coaxial cable structures form the subject of substantial theoretical and experimental investigations either directly related, or which can be extrapolated, to the communications needs and environments of U.S. coal mines. Communication systems based on "guided" waves, of which "leaky" coaxial cables are one implementation, are attractive candidates for providing a range of communication functions primarily along haulage ways, and possible also within sections up to the working face. (However, there are still strong reservations as to whether a practical coaxial cable sys tem could provide sufficient communications coverage within a section. ) In this Part, we present the results of some theoretical calculations of the performance of leaky coaxial cable communication systems. We also analyze the applicability of the theoretical and experimental results obtained by other researchers to the needs of U.S. coal mines. In particular, this investigation has been focused on the utility of relatively low cost, conventional, flexible, coaxial cable at frequencies covering the LF through HF bands and extending into the lower part of the VHF band, as opposed to relatively high cost, special semi-rigid, coaxial cable* at frequencies in the VHF and UHF bands. There are three major design alternatives for coaxial cable communication systems considered in this chapter: • Base station feeding a coaxial cable with high surface transfer impedance (holes in outer conductor, e.g., braid construction). • Base station feeding a coaxial cable with repeaters (U.K. experiments). • No base station, direct communication via a coaxial cable with periodic radiative structures.

Jan 1, 1974

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By J. J. Wallace

1. The Pittsburgh is the most important bed in Greene County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 6,011 million short tons as of January 1, 1954. Of this total, 5,967 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By J. Burlin Johnson

In small-scale blasting experiments conducted in the Bureau of Mines laboratory, small charges were used to produce craters in blocks of concrete mortar. The results are compared with larger scale experiments of other research workers, and the comparison demonstrates the similarity of the results obtained and indicates that small-scale blasting should be a useful tool for predicting large-scale blasting effects. INTRODUCTION The purpose at this investigation was to conduct blasting experiments in mortar in the laboratory and then, by comparing the results with those from larger scale field blasts in rock to determine to what extent, if any, the laboratory results resemble those in the field. The work described herein was the initial phase of a project aimed at evaluating small-scale blasting as a tool for use in improving blasting techniques. It is evident from the stand-point of control and cost that small-scale blasting would be valuable in the study of rock fragmentation by blasting in mines and quarries, if the extrapolation is valid.

Jan 1, 1962

By Joseph A. Perry

One goal of the Bureau of Mines is to develop technology tp insure a dependable supply of minerals to the United States. To support this goal, the Bureau's Albany Research Center has modified a commercial atomic absorption spectrophotometer to rapidly determine trace levels of mercury by cold-vapor atomic absorption spectrophotometry. Such diverse materials as ores, mill products, stream water, sediments, and flue dust have been analyzed. A very high dynamic range of 0.2 ng/ml to 1 µg/ml of mercury in solutions is routinely analyzed by this instrument.

Jan 1, 1981

By Russell C. Frith, David C. Oyler, Dolinar Dennis R., Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures. To help determine what factors contribute to such failures, a comprehensive international database of 131 case histories has been compiled. The cases include six failures where major rock falls occurred in front of the shields, and seven even more serious failures involving major overburden weighting. The case studies suggest two types of room failure mechanism. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender or remnant longwall panel narrows. The second is an overburden weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rockwell above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used. Weighting failures were not greatly affected by the density of roof reinforcement. In one of the overburden weighting cases, in a Pittsburgh coal bed mine, stress cell, convergence, bolt load and extensometer data have been used to analyze the failure in detail. Key words: coal mining, ground control, longwall, recovery room.

By William M. Nabors

As a part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers are studying secondary oil-recovery projects in the United States. Published reports that set forth the pertinent facts of these operations help others to profit by the experience gained. This report presents the results of a study of secondary-recovery methods used in Kentucky by the Cumberland Petroleum Co. on its L. C. Bailey lease, Oil Springs pool, Magoffin County, Ky. This is believed to be the first water-flooding project in eastern Kentucky (fig. 1).

Jan 1, 1958

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 961 Bcf as of January 1, 1983. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas re- serves, 271 Bcf, (2) helium in probable natural gas resources, estimated at 202 Bcf, (3) helium in possible natural gas resources, estimated to be 351 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 137 Bcf. These helium resources are further divided into depleting, nondepleting, and stored classifications. The depleting resources are those associated with natural gas fields that are, or will be, produced for the natural gas they contain. All of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 789 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 134 Bcf. There is 38 Bcf of helium in storage in the Federal Government- owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1985

By Foster Fraas

Electrostatic separation depends on a number of electrical and mechanical properties such as conductance, contact potential, dielectric constant, and particle shape. In routine testing it is desirable that the application of each of those properties be investigated. The conductance property is best utilized in a separator having an ionic field, whereas the contact potential requires a separator with a pure static field. Dielectric constant and particle shape also influence the response in these two fields. There is no separator on the market that can be adjusted for all these requirements. The separator described in this paper is satisfactory for this purpose and is provided with a dielectric electrode, which permits formation of high-intensity static fields.

Jan 1, 1951

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

The Federal Coal Mine Health and Safety Act of 1969 has dictated major changes in mine ventilation with regard to both air quantity and quality. Requirements have also been placed on the ventilation of beltlines, gob and face areas, and air velocities on trolley haulage roads are limited. Escapeways, separate from trolley haulage roads and on an intake split of air, must be maintained continuous to the surface. These and other similar requirements have not only precipitated several modifications to existing ventilation systems but also have greatly increased the complexities of new mine ventilation planning. It is apparent that the use of computers in ventilation system analysis and design is a necessity. SUMMARY Although computer oriented analysis of mine ventilation systems was introduced over two decades ago, it has yet to receive widespread acceptance in the United States. Central to this problem is the fact that, while many computer programs for network analysis have been developed, no attention has been paid to the development of computer input data. Consequently, without this foundation, program applications have been infrequent. This thesis has directly attacked this problem and has presented all pertinent information basic to the development of good computer input data. The areas that were covered include quantity measurement, pressure measurement, fan testing, survey data balancing, and the development of a network schematic from the ventilation survey results. These discussions on data collection and the corresponding reduction to computer coding have been illustrated by an application of a ventilation simulation program to an existing mine in Southwestern Pennsylvania. The use of a ventilation

Jan 1, 1977

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other volumes of the international studies of the Minerals Yearbook, it is clearly impossible to cite all sources of information used in its presentation, but some recognition seems due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of our counterpart agencies throughout the world. Information they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, we must begin by expressing our appreciation to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1993

By J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 3S0 meters (1150 ft.) and 488 meters (1600 ft.). The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broadband, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or F layers of ionosphere as an upper plane and the earth as a lower plane.

Jan 1, 1974