Search Documents

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume n of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output!' It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1979

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines (USBM) and the US. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSRYs were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 1994

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0, 22.5, and 45). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined.Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01).Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (atleast for older specimens)

By Stephen D. Smith

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing. the stage of measurement used in this chapter is what is normally termed ?mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1989

By Heine Kenworthy

"INTRODUCTION In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral content of this ore was considerably higher than in, the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently, tailing losses, especially with respect to lead, were high. A few years later, in order to study the possibilities of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill, feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Sta¬tion for testing-. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values was present.A résumé of the ore-dressing treatment used in the Shenandoah-Dives mill follows. After crushing, the ore passes through a ball mill, the minus 5-mesh discharge of which is distributed to three tables. A finished lead concentrate is made on the tables, and the table tailing goes to the classifier which is in closed circuit with the ball mill. The classifier overflow is treated -by flotation to obtain a bulk sulfide concentrate at a relatively coarse size. The bulk concentrate is thickened and reground to about 95 percent minus 325-mesh before flotation treatment to separate a lead-copper and a zinc concentrate. A typical monthly average showed that the table concentrate contained about 45 percent lead, 1 percent copper, 4 percent zinc, 12 ounces of gold, and 40 ounces of silver; that the lead flotation concentrate contained '35 percent load, 6 percent copper, 7 percent zinc, 3.5 ounces of gold, and 50 ounces of silver; and that the zinc flotation concentrate contained 2 percent lead, 0.5 percent copper, 60 percent zinc, 0.15 ounces of gold, and 4 ounces of silver. Recoveries in salable products were roughly b5 percent of the lead, 70 percent of the copper, 45 percent of the zinc, 85 percent of the gold, and b5 percent of the silver."

May 1, 1948

The Department of Interior, U.S. Bureau of Mines performs the task of estimating the quantity of coal reserves existing in each state on a county by county basis. As a part of Information Circular 8655, the Bureau of Mines established the criteria for the uniform estimations of coal reserves and listed the most recent estimates of coal reserves by county and by seam. At the same time however, the Bureau recognized that these figures represented the upper bound with regard to the estimated actually usable or obtainable reserves. Recovery of these reserves are subject to the mining methods used and to the resolution of such problems as the use of poor quality coal and competition provided by conflicting land use. These problems, in practice restrict the recovery of the estimated quantities of coal reserves listed in IC 8655. Another impact, the subject of this manual, is the impact resulting from previous mining activities. In particular, many of the reserve seams included in the reserve estimates overlie or underlie mined-out coal beds. Portions of these reserve seams may therefore be unmineable or at best may have a reduced quantity of extractable coal. In order to improve the accuracy of the coal reserve base estimates, the Bureau of Mines funded an effort1 to develop a systematic methodology for estimating the coal loss associated with the impact of previous mining activity. The coal loss calculation model (CLCM) described in this manual is a result of that effort and addresses the percentage of coal loss in reserve seams due to previous overmining or undermining.

Jan 1, 1976

By L. C. IlsLey

The work of the electrical section of the Bureau of Mines may be considered to have had its beginning in April , 1909 , when H. H. Clark was , appointed electrical engineer in the U. S. Geological Survey. The first manuscript prepared by members of this section was Miners Circular 5, which was issued in October , 1911. During each succeeding year additional papers have been published dealing with questions relating to electrical safety. Since 1916 the electrical section has also conducted laboratory investigations on flame safety lamps and gas- detecting devices and has published reports relating thereto . The following selected list of publications covering safety studies and activities of the electrical section has been prepared for the convenience of those who wish to keep themselves advised concerning electrical safety matters . The list includes only such publications as are applicable to present-day prac tices .

Jul 1, 1930

By David C. Oyler, Paul B. Stubbs

The Bureau of Mines and United States Steel Corp. are conducting a joint project to monitor formation pressures at a large (23-well) coal- bed gas drainage field near Oak Grove, AL. Three monitor holes were drilled in late 1981, and pressure monitoring began in December 1981. The Bureau of Mines direct method was used to obtain gas content data from cores taken in the monitor holes. Comparison of the 1981 gas con- tent data from the monitor holes with initial gas content values obtain- ed from the production wells in 1977 indicates a 50-pct reduction in ad- sorbed gas content inside the pattern and a 29-pct reduction at one point 500 ft outside the pattern. The combination of pressure and gas content data has also allowed an in situ isotherm curve, relating the formation pressure to adsorbed gas content, to be developed for the area of the production wells. From the current rate of pressure decline (1 lbf/inz per month), the observed changes in gas content, and the isotherm curve, it appears that most of the early gas production came from within the pattern, but since 1981 (and possibly earlier) most of the gas produced has been migrating to the wells from outside the pattern area.

Jan 1, 1985

By Lucia Kuizon

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the Diamond Peak area comprising 183,000 acres in the Challis and Targhee National Forests in order to evaluate its identified mineral resources. More than 3,000 mining claims were located in three mining districts between the years 1882 and 1986. Approximately 230 mining claims in and the 150 claims adjacent to the study area were current in 1986, when Bureau of Land Management mining records were researched for this study. A total of 1,270 samples were collected from these sites (30 were for alluvial placer). Results of the investigation help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Lead-, silver-, zinc-, copper-, and gold-bearing minerals occur as veins and replacement bodies in shear and fault zones in Precambrian and Paleozoic calcareous Sedimentary rocks that have been complexly folded and faulted. Total production from the three mining districts in the study area was more than 150,000 tons of ore between 1901 and 1982. Approximately 11,600 tons of subeconomic resources consisting of lead, silver, zinc and copper were identified within the area. Over 37,500 tons of lead and zinc subeconomic resources were identified just outside the area. In addition, lead-, silver-, and zinc-mineral resources were identified at 4 mines within 2 miles of the study area. Iron mineral resources were also identified just outside the area.

Jan 1, 1991

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 1927 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein.

Jan 1, 1935

By Jack D. Ramsdell

The objective of this investigation was to make a preliminary evaluation of titanium-vanadium-zirconium, alloys using room-temperature tensile properties as criteria for selecting promising alloys for future critical studies. Arc-melted titanium-vanadium-zirconium alloys ranging in composition from 5 to 20 a/o (atomic-percent) vanadium and 5 to 30 a/o zirconium, were investigated to evaluate hardness, hot workability, and room-temperature tensile properties. Metallographic examination coupled with hardness measurements were used to follow structural changes and aging response. Room-temperature tensile properties were criteria for evaluating mechanical and engineering properties of the alloys.

Jan 1, 1960

By G. M. Kintz, E. H. Denny

Although some engineering colleges recognize the importance of instructing young engineers in industrial safety , the different institutions handle this instruction in various ways . It is believed that a recent industrial safety course , conducted at the Colorado School of Mines through the cooperation of this school and the Bureau of Mines , U. S. Department of Commerce , presents some unusual features that are of interest to other schools and to the mining public .

Sep 1, 1930

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

6. Computer Simulation of Mine Evacuation Analysis of mine evacuation involves manipulating a large number of interacting variables, such as mine passages, hoist movements, miner position etc. , which makes the problem very difficult to solve without use of a digital computer. Therefore, under this contract, a computer program is written to simulate evacuation of a mine under different configurations. The simulation input variables include characteristics of the mine, expressed in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self-rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i. e , fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effect of the fire on ventilation or on the miners is not considered. The simulation output includes the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure time of the miners. Details of the mine evacuation program are summarized in Appendices A and B Appendix A describes structure of the program and its capabilities. The flexibility of the program and its suggested uses are demostrated by a number of illustrative examples Appendix B is a user&apos; s manual for the program which includes instructions for program use and explanation of the logic employed in the program. A computer listing and printout of a typical output are also included in the Appendix B The ten illustrative examples summarized in Section A 4 (Appendix A) provide proof of validity of the program and help make certain inferences about mine evacuation. The first example, which is simulation of an actual mine fire drill conducted in a mine, has predicted evacuation time within 5 percent of the actual evacuation time in the fire drill, demonstrating thereby, the ability of the program to make accurate predictions.

Jan 1, 1976

By A. C. Rice

Aminopolyacetic acid chelating agents were added to separatory-funnel-scale solvent-extraction systems to determine the effect on separating rare-earth elements. Average values for separation factors between adjacent elements obtained with Primene JM-T2 increase 36 percent when EDTA is added to the aqueous phase. Adding HEDTA or DCTA also improves separation factors for certain rare-earth elements. Percentage of extraction and the separation factors exhibit marked sensitivity to concentrations of amine, chelating agent, and hydrogen ion. The chelating agents improved separation in Primene JM-T, BHDA, and Primene 81-R extraction systems.

Jan 1, 1963

By R. R. Allen

Gieseler plastometer tests were performed on eight western coking coals at retort - immersion depths ranging from 2 to 3-3 /4 inches (measured to the center of the coal charge ) . Increased maximum fluidities were associated with greater retort - immersion depths , the most pronounced increases being observed on highly swelling coals when tested at 3-3 /4 inches . The maximum fluidity of one of these coals when tested at 3-3 /4 inches was 146 percent greater than that observed at 24 inches . Retort - immersion depth had no significant effect on the temperatures of initial softening , fusion , maximum fluidity , end of fusion , and solidification .

Jan 1, 1964

By Gordon E. Fletcher

This Bureau of Mines report outlines the atomic absorption analysis of oilfield brines for barium, calcium, copper, iron, lead lithium, magnesium, manganese, potassium, sodium, strontium, and zinc, using the method of additions. The advantages of using atomic absorption are discussed. The method of additions was chosen to overcome large matrix interferences usually found in brines; techniques of overcoming chemical, ionization, and background interferences are also described. The method was used to analyze several hundred oilfield brines and found to be rapid and reasonably accurate. A solvent extraction method was used to concentrate lead, copper, zinc, and iron in low-level samples.

Jan 1, 1974

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959