Search Documents

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960

By S. H. Katz, J. J. Bloomfield

Fires in zinc dust have sometimes given particular trouble owing to their resistance to extinguishers and the liability of explosions . Similar problems , notably with aluminum dust* , have previously been subjects of investigation by the Bureau of Mines .

Mar 1, 1922

By W. C. Hudson

"The Miami-West Palm Beach belt of silica sand, which may be suitable for the manufacture of high-grade glass, extends 65 miles northward from the neighborhood of Miami to the vicinity of West Palm Beach, The sand presumably originated in the host rocks constituting the oceanward slope of the Appalachian Mountains and the Piedmont Plateau of Georgia and the Carolinas. The sand now lies in a long, narrow, and probably thin belt that forms a dune-capped terrace marking a previous stage of submergence. The highest dune crests appear to be no more than 30 feet above sea level, and the water table is about 10 or 15 feet below the general level of the terrace.The width of the belt in several places is known to be more than a mile, and the thickness of the clean glass sand sampled ranged from 4 to more than 7 feet. Visual inspection and the meager data indicate the existence of bodies of glass sand large enough to supply foreseeable markets.Analyses of three samples indicate that beneficiation would make the sand suitable for the better grades of ordinary and flint glass.The prospective grade and quantity of sand, an available market in Florida for glassware, and the expectation of postwar expansion of the new industry of glass producing justify more detailed exploratory work and beneficiation testing.U. S. Route No. 1, Old Dixie Highway, the Seaboard Railway, and the Florida East Coast Railway, all substantially parallel and usually within a width of a mile or two, run along parts of the belt or between it and the coast. In addition to many streets and unpaved roads, a paved road crosses the belt at right angles about every 5 miles. Numerous towns are situated within or near the belt. Any area selected for a mining, processing, and manufacturing plant would be near a railroad, a highway, and water and also accessible to public utilities.The subtropical climate, famous for its pleasantly warm winters, would preclude seasonal interruption of plant operations."

Apr 1, 1946

By R. Barany

The heats of formation of goethite, ferrous vanadate, and manganese molybdate at 298.15° K were determined by solution calorimetry. For formation from the elements, the heat values were -133.7 ±0.3 kcal/mole for goethite, -453.8 ±0.5 kcal/mole for ferrous vanadate, and -284.8 ±0.2 kcal/mole for manganese molybdate. For formation from the oxides, the heat values were -0.9 ±0.1 kca1/mole for goethite, -19.4 ±0.3 kca1/mole for ferrous vanadate, and -14.6 ±O.l kcal/mole for manganese molybdate.

Jan 1, 1965

By David Cooper, Susan Robertson, William Wiehagen, Launa Mallett, Charles Vaught, Joan Dickerson, Richard Conkle, ROBERT PETERS, Mike Brnich, Charles Urban

This trainer’s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators’ manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer’s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee’s knowledge and skills and (2) the trainer’s experience in conducting skills training. The “Skill Check” section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of “teachable moments” where significantly new knowledge and skills can be learned. The videos on the DVD that accompany this guide can be shown at the beginning of training to give trainees an idea of what the job entails and related requirements. They can also be used within the training cycle (after the trainee has some experience in the job) to reinforce key points or as a trigger for eliciting questions about particularly difficult parts of the job. The video segments are meant to be visual models of good performance. They are designed to elicit discussion on good (lower risk) ways to do the job. In this context, they can be used very creatively at different times within the training cycle. The section on “Talking Points” offers a number of questions that can be used in the classroom to support and elaborate on certain aspects of the job duties. If the trainee has a fair amount of underground experience, some of the questions can also be used to support the pretraining assessment (i.e., skill check) of knowledge and skills. Likewise, some of the questions can also be used while teaching on the job to reinforce key points affecting safety, production, or maintenance. The section dealing with a mine’s roof control plan should be used at various times in the training cycle to make sure the trainee understands the plan and knows how to apply it in performing the job. The supplemental materials offer additional resources that can be used to support initial job training or follow-up. Learning continues well after an individual has been trained. The supplemental materials can help reinforce good operating skills and provide an opportunity for further discussion on better ways to do the job.

Jan 8, 2006

By W. H. Lewis

This Bureau of Mines report and its companion report (Information Circular 9073) have been prepared as a complete reference on underground coal mine lighting. This report discusses system design criteria and procedures, data and specifications to aid in selection of suitable mine lighting hardware, and guidelines for system installation and maintenance. Topics include light measuring techniques and instruments, illumination regulations for underground coal mine environments and equipment, lamps and ballasts, available mine lighting hardware, design and evaluation of coal mine illumination systems, and installation and maintenance of a mine lighting system.

Jan 1, 1986

By A. Wahab Khair

"This paper deals with the description of the capabilities of a unique rotary coal cutting simulator which has been designed and fabricated at West Virginia University. It operates under the simulated mining conditions with in-situ stresses (horizontal and vertical stresses) being applied to a coal block of 18 in. x 15 in . x 6 in located in a suitably designed confining chamber. Cutting drum rotation can be varied from 1 to 40 rpm with the capability of stopping the drum after a predetermined number of rotations. Tests can be performed with four different bit angles, 15, 30, 45 and 60 degrees . A maximum of seven bits could be used in seven different orbits. Various cutting depths up to a maximum of 4 in. is possible.Monitoring devices constitute, Linear Variable Differential Transformers (LVDTs), pressure transducers, cascade Impactors, flow meters, flow controls and drum cutting speed. LVDTs are used to monitor the displacement of the coal block as well as the depth of cut. Pressure transducers are used to monitor the changes in pressure, both due to the thrust and due, to the intermittent cutting nature of the rotary cutting. Flow controls will be used to run the drum at a set rpm between 1 and 40 and to provide a different rate of advance. All the above mentioned devices can be operated and monitored by a fully automated control system. Six-stage cascade impactors are used to determine the mass distribution of dust along the rotation path of the drum. The fracture size, shape and Intensity can be studied by optical microscopy and the dust entrainment by using high speed photography.This equipment will basically be used to study the fracture mechanism in coal, associated with operating and in-situ parameters and further relate It to dust generation and entrainment In underground coal mines."

Jan 1, 1988

By D. D. Bolstad

This report describes the construction and use of a direct-reading azimuth protractor (DRAP) by the Bureau of Mines for measuring fracture orientations in mines, tunnels, or other excavations having a magnetic environment. The DRAP allows a rapid and simultaneous measurement of dip and azimuth of dip of a fracture plane. The instrument is rugged, lightweight, and easily constructible from standard hardware items. The DRAP can measure dip to within ±0.5° and azimuth of dip to within ±5° of corresponding values obtained with a Brunton compass.

Jan 1, 1974

By D. B. Dow

The transportation of any commodity which is actually or potentially a source of fire or explosion, has been made safe, insofar as humanly possible, by rigid requirements as to inspection mechanical safety devices, and by printed labels. For the most part these precautions have been sufficient. This is evident when it is considered that in the thousands of instances in which commodities with a great fire risk have been transported, few disasters have occurred. This paper deals with the recent gasoline explosion which occurred at Memphis, Tennessee. At 7:50 a.m. January 24, 1921, vapors from a tan: car of gasoline became ignited and resulted in a blast that killed eleven people and badly injured nineteen others. Probably forty or fifty men, women, and children received slight injuries from falling debris or from burns. The explosion wrecked an oil plant, leveled a block of frame buildings, and broke window panes within a radius of five blocks.

Feb 1, 1921

By C. J. Mains

The gas -flow oil-shale retort is a continuous, crass flow, gas -to -broken solid heat-exchange system in which heat is transferred by convection from the gas to the solide.2/ This type of heat transfer presents a problem of analysis that cannot be solved by methods in common use. Solution of this problem is necessary for design, operation analysis, and predict ion wherever that type of heat exchanger is used. This report embodies a method for calculation of heat transfer coefficient and temperature histories of gas and solid in the gas- flow retort operating at equilibrium conditions. Detailed calculations are presented to show the application of the method explained in this report to conditions of an actual run made in the gas-flow retort. Although used here for a specific case, the method is applicable to all heat exchangers that are characterized by continuous, crossflow, gas -to-broken solid heat transfer. INTRODUCTION In any direct, gas -to -broken solid heat -transfer system, it is difficult to measure the temperatures of the gas and solid inside the heat exchanger. The driving force for heat transfer between the two media in the bed there- fore usually is unknown. The major resistance to heat transfer is in the gas film surrounding the solid particles, and the thickness of this gas film is neither uniform nor can it be determined readily. It is well to point out also that determination of the surface area of the particles is of poor accuracy. Since the driving force, the major resistance, and the surface area in the heat-transfer system are such uncertain quantities, It is not feasible to calculate the heat transfer by usual methods. All of the fore- going statements are true of the gas-flow retort; as a result, efforts were made to determine apparent heat-transfer coefficients and temperature histories of gas and solid in the heat -exchange bed by calculation using those data that were available. The heat -transfer coefficient calculated has the following dimensions: B .t .u. per second, °F., cubic foot of bed volume, where heat - transfer coefficients normally have the units; B .t .u . per hour, square foot, °F. Only the Schumann-Furnas formulas may be used to determine the heat- transfer coefficient and temperature histories in this type of heat exchanger.

Jan 1, 1953

By D. J. Parker, J. B. Benson, J. H. Bird, F. E. Cash

"INTRODUCTION The organic act that became effective July 1, 1910, imposes two very definite primary obligations upon the Bureau of Mines: (1) The prevention of loss of life and limb and the protection of the health of workers in the mineral industries, and (2) the conservation and scientific utilization of the country's mineral resources.The subject of this publication falls within the scope of both of these responsibilities by reason of the fact that (1) certain safety precautions are involved in combating even surface fires and, (2) although peat is not now, so far as known, utilized commercially or otherwise in this country as a fuel, it is extremely valuable agriculturally in at least one of our States, The justification for the conservation of such low-grade fuel through fire prevention appears warranted because of its present value to agriculture and the possible advantages accruing to future generations as a source of heat and power.Although the Bureau of Mines has published information on the origin and uses of peat, this is the first attempt to give out data concerning the prevention and control of peat-bog fires. Although the information presented here is restricted to the Lake Superior District, California, and Florida, there may be similar conditions in other sections of the country that have not come to the attention of engineers of the Bureau of Nines."

Jul 1, 1947

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

By C. A. Rhoades

A major contributor to the problem of short life expectancy for blade-type conveyor belt cleaners is uneven wear along the blade edge. Uneven wear results in the formation of channels in the blade edge, which allow material to be carried back between the blade and the belt. In an effort to reduce the uneven wear problem, the U.S. Bureau of Mines has studied the mechanisms responsible for effective belt cleaning. From this study emerged a design for a cleaner blade that would greatly reduce uneven edge wear. The design consists of a standard cleaner blade incorporating air passages that allow for the expulsion of air along that part of the blade edge in contact with the conveyor belt surface. The results of 18-h tests indicated that the expulsion of air on the blade edge prevents scratches from developing into deep grooves. These tests showed that effective blade cleaning life can be extended 25 times using the pneumatic cleaning blade, compared with solid metal cleaning blades.

Jan 1, 1989

By Kihong Park

A hygroscopicity tandem differential mobility analyzer (HTDMA) technique is used to determine size-effect of nanoparticles (NaCl, (NH4)2 SO4, KCl, NH4NO3, MgCl2,CaCl2) on their hygro­scopic properties (deliquescence relative humidity (DRH) and hygroscopic growth factor (GF)). The HTDMA system uses a combination of two nano DMAs and two regular DMAs to measure particle size change in a wide dynamic particle size range. Particles are subsequently analyzed with a transmission electron microscopy to investigate the potential effect of particle structure or morphology on the hygroscopic properties. We found that structural properties of NaCl and (NH4)2SO4 particles also play an important role in determination of the DRH and GF and are more pronounced at smaller diameters. Data show that the DRH of NaCl nanoparticles increased from *75% up to *83% RH at 8 nm and that their GF decreased with decreasing size. The extent to which the GF of NaCl nanoparticles decreased with decreasing size was greater than theoretically predicted with the Kelvin correction. The GF of furnace-generated NaCl nano­particles that have pores and aggregate shape was found to be smaller than that of atomizer-generated particles that are close to perfectly cubic. For the case of atomizer-generated (NH4)2SO4 nanoparticles, we observed no signi?cant size-effect on their DRH, and the measured GF agreed well with predicted values using the Kelvin correction. For furnace-generated (NH4)2SO4 nanoparticles, a gradual growth at moder­ate RH without noticeable deliquescence behavior occurred. Their TEM images showed that contrary to atomizer-generated (NH4)2SO4 nanoparticles the fur­nace-generated (NH4)2SO4 nanoparticles are not perfectly spherical and are often aggregates having pores and holes, which may favor holding residual water even in the dried condition. For atomizer-generated KCl, MgCl2, and CaCl2 nanoparticles, we observed no signi?cant size-effects on their DRH and GF for the mobility size as small as 20 nm.

Jan 1, 2008

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

Identity the difficulties of establishing vegetation on mining-related wastes resulting from adverse chemical, physical, and biological properties; describe the ecological and soil factors affecting the relationship between mycorrhizal fungi (soil microorganisms) and plants; and evaluate the feasibility of establishing vegetation on mine waste by introducing mycorrhizae. Problems in Revegetation Successfully using vegetation to stabilize a situ disturbed by mining-related activities depends on knowing the chemical, physical, and biological characteristics of the site prior to, or at the time of, stabilization. The primary objectives of mine land reclamation are to minimize environmental degradation and to facilitate the re-establishment of a functional plant-soil system. Mining disturbances can significantly alter the physical, chem¬ical, and biological characteristic of a site, thus affecting plant establishment, survival, and growth. The physical disturbance caused by the removal and replacement of soil and overburden, together with the waste material from ore processing, affect the chemical, physical, and biological process within the disturbed soil or waste. Additionally, variability in soil properties results from differences in climate, topography, vegetation, and parent material of the site.

Jan 1, 1993

By Thomas C. Miller, Charles E. Mongan

"This publication is a progress report on Bureau of Mines studies in applying sonar techniques to roof-control problems in coal mines. Preliminary tests in the laboratory were made on layers of roof rock. To apply the experience thus obtained, a unit was designed and constructed and was used underground.The term ""sonar technique"" refers to the system of generating a beam of sound waves, shaping and directing the beam, introducing the beam into a medium to be studied, and examining any returning waves with a view of inferring the nature of the material traversed by the waves and the presence of interfaces or obstacles in the medium.The theory and actual underground experiments indicate that the sonic method is feasible. Information from physical tests made in the Bureau's Experimental mine confirmed the validity and potential usefulness of the sonar method. Lighter and more compact apparatus is desirable, and permissible equipment suitable for use in gassy or dusty mines must be developed. However, no particular difficulties are anticipated; consequently, this scientific approach to the exploration of roof strata shows definite promise. INTRODUCTIONThe problem of roof control in the coal-mining industry is of major importance. More than 50 percent of all coal-mine fatalities and 25 percent of all nonfatal serious injuries are caused by falls of roof, face, or ribs. The Bureau estimates that more than $128 million was spent by the coal-mining industry in 1958 for supporting roof."

Feb 1, 1960

By Charles L. Kimbell

This study is intended to serve three roles. First, it represents a global overview and summary to supplement and complement the five regional companion volumes of the 1991 edition of the Minerals Yearbook International Review. In this regard, it also extends previous time series under this title that appeared as the introductory chapter to the international volume of the Minerals Yearbook from the inception of that volume in 1963 until it was subdivided into separate regional volumes in 1989. The basic statistical presentations herein generally contain data through and including that for 1991, although in a few instances the most recent statistics are those for earlier years because more recent, comprehensive global statistics simply are not yet available owing to delays in data collection and processing in some countries and continued governmental suppression of data in others. The second role of this study is to provide an update to the coverage of events impacting the world's mineral industry that have occurred between the end of 1991 and the preparation of this study. Inclusion of this update is almost essential because of the potential effect of some of these events on global mineral industry activities.

Jan 1, 1993

By John B. Goodman

This report presents a study of a modification of the precision laboratory carbonization-assay apparatus that renders the unit capable of performance at low-, medium-, and high-temperature assay levels and permits, under controlled conditions, evaluation of the relationship between carbonization temperature and the yield of pyrolysis products. Second, the interest and value derived from the temperature study data directly apply to the particular semiplant carbonization processes and techniques currently being investigated in this laboratory. Data obtained with the assay apparatus enables the fuel technologist to predict the probable yields of carbonization products from pilot-plant operations under various carbonizing conditions. Data obtained with the assay apparatus has been used to predict the product yields of industrial carbonization plants at Kemmerer, Wyo., and Rockdale, Tex. The assay provides a useful tool in detecting, from the carbonized plant product, the degree of effectiveness of pilot-plant operation. Third, the residual volatile matter in some industrial carbons has broad significance. Evaluation of the volatile material remaining with or in the carbon may be assessed through the high-temperature-assay technique. The low-temperature carbonization assay devised by the writers has proved to be a versatile tool in predicting the probable product yields from pilot-scale carbonization processes. The apparatus described in previous publications has been modified to extend the range of testing above 500° C. without impairing the accuracy and reproducibility obtained in the low-temperature range. Results presented here include product yields from a typical Texas lignite and Wyoming subbituminous-B-rank coal over the temperature range 150° to 1,000° C.

Jan 1, 1958

By Ray J. Holmquist

"INTRODUCTION The Elk Mountain mica deposit was examined in June 1943 by the Bureau of Mines. An exploratory project and an access road for the property were recommended, provided the zinc was put in operation under competent management. K. Garard obtained a lease on the properly and started operations in June 1944; this was followed immediately by the Bureau's exploratory work. Road construction was begun by the Forest Service in July the same year.The lessee mined mica from the richest exposure with a crew of three men for 2-1/2 months. His operation terminated late in September, but the Bureau of Mines project and the Forest Service road construction continued until snow forced suspension of activity during the first week of November.The Bureau of Mines work consisted of trenching with a bulldozer, hand excavating on undeveloped outcrops, extending an existing adit, and starting a new adit below the older workings."

Jul 1, 1946