Search Documents

By Thomas R. Bur

The order of identification and in same cases the magnitude of the elastic constants of an anisotropic material depends on the orientation of the cartesian coordinate axes with respect to a set of reference coordinate axes within the material; thus confusion will result unless standard orientations are used. In this paper the relationship between the cause (the internal fabric) and the effect (the elastic properties in this case) is discussed for single crystals and for polycrystalline and amorphous materials. While reference axes based on the cause are used in the IRE (Institute of Radio Engineers) standard for piezoelectric crystals) it is shown that a reference coordinate system that would be suitable and practical for all anisotropic polycrystalline and amorphous materials must be based directly on a three-dimensional expression of the effect. The conventions offered are similar to the IRE standards for piezoelectric crystals) but use the elastic coordinates of the wave surface which can be quite readily established experimentally as the reference coordinates.

Jan 1, 1969

By George H. Johnson

An evaluation of the diamond-bit-performance data accumulated from core-drilling cherty limestone and cherty dolomite reveals that the percentage of core recovered and the physical characteristics of the bits and diamonds used are economically significant. One of the established trends, of particular interest to those engaged in diamond drilling, is that bits set with small, low-quality, West African drill bort are the most economical. Detailed analysis of the factors that affect diamond-bit performances, such as diamond size and quality, bit size and type, percentage of core recovered, and the physical characteristics of the bit matrices are assessed in the tables, charts, and discussion.

Jan 1, 1958

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By Robert S. Sanford

The Broughton and Ring magnetite deposits in Essex County, N. Y., are thought to be in a mineralized belt that extends from the Lake Sanford mining district to Lake Champlain and passes through the Mineville district. The country rook is syenite-gneiss, similar to that in the Mineville area. The Bureau of Mines conducted a vertical magnetometer survey of the area. On the Broughton properties there are no indications, magnetically, of magnetite in any degree of concentration. 'On the ding properties a number of sharp, localized magnetic anomalies were observed. One core-drill hole was bored to a, depth of 48.3 feet, also, to test one of the strongest anomalies. The field work was in progress from December 1943 to July 1944. Although no iron ore was intersected by' the drill hole, it showed that the amphibolite rook, at a depth of 6 to 100 feet below the surface, contained enough magnetite and iron sulfides to account for the anomalies recorded by the magnetometer survey.

Jan 1, 1949

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By D. Harringtong

"There has been much writing and argument on the subject of giving bonuses to miners, quarrymen, metallurgical and chemical workers, and others as a stimulus for safe work and for work safely done. Theoretically, everyone should be careful and should not need monetary or any other type of encouragement for the prevention of accidents; as a. fact, few people are careful, and this is primarily the reason way many if not most accidents occur. A bonus, however, is not simply money given away by an employer; it must be earned, so to speak, before it becomes due; in other words, if the standard established is not reached, no bonus is paid, and in many cases some disciplinary action is taken.The United States Bureau of Mines Is asked from time to time for suggestions for rewards to mine workers who have a good attitude toward working safely or who need some stimulus to cause them to make greater or more earnest efforts toward safety for themselves and their co-workers. A recent inquiry prompted the collection of data on some safety bonus systems from reports of this bureau's field engineers and others, and some of these Now given. Bonus practice at both coal and metal mines is included because a system used at metal mines is generally adaptable to coal mines; in fact, in numerous cases, bonus systems recently started at some coal mines are based on systems in vogue and giving satisfaction some metal mines; in-some instances, also, metal mines have been able to get good suggestions from coal mines or from the cement or petroleum industries. it .should be understood that a bonus, even as applied to the encouragement of safety, does not necessarily mean payment of money; in fact, some successful bonus systems have in them no direct money exchange; hence, the bonus as treated in this paper is that defined as ""Something given in addition to what is ordinarily received by, or strictly due to, the recipient.""Acknowledgment is given here to members of the safety division of the Bureau of Mines who sent in some of the information here presented; to the Engineering and Mining Journal and Mining Congress Journal, from which some items were abstracted; to various mining officials who gave data in one form or another; and to M. von Bernewitz, of the United. States Bureau of lines who aided in framing parts of this paper."

Jun 1, 1932

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method, Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out- crop will emit low levels of methane gas.

Jan 1, 1977

By D. Harrington, C. W. Owings

Each year at least one and in some years several explosions are reported as having resulted from firing of mudcapped shots in coal mines; undoubtedly a number of small or local explosions occur that are not reported; in addition there are numerous accidents, some of them fatal, attributable to this reprehensible blasting practice. It is surprising that so few explosions and other accidents from this cause occur since the practice of firing mudcapped, Even in gassy "adobe," "dobe," "sand blast," or "bulldozed" shots is widespread. mines where general blasting is safeguarded by being done with permissible explo- sives, rocks or bowlders frequently are blasted with mudcapped shots of dynamite; even if permissible explosives are used, this type of shooting is dangerous. The usual method of preparing a mudcapped shot is to place the explosive, either in loose or cartridge form, with the detonator or "cap" on top of a piece of rock or coal and cover it with several handfuls of moist clay, loam, sand, or When the shot is road dust; in many cases there is no covering of any kind. fired a dense cloud of dust, together with an intensively hot fleme, are thrown into suspension, and if the dust is explosive or ignitable an explosion or igni- tion is likely to result practically simultaneously. The presence of gas greatly increases the explosibility of the dust, as well as the probability of an ignition. Every shot, of any known explosive, fired in a coal mine without having the charge properly confined in a drill hole and tamped with incombustible stemming to the collar of the hole, is capable of initiating an explosion that may cause the death of every man in the mine. Attention has recently been directed to this unsafe practice by an explo- sion resulting from a flagrant disregard of safe blasting practices in one of our The mine had been idle for several years most productive coal-mining regions. and was being prepared for reopening on a different system of mining. Six to 10 inches of bottom coal had been left in place during former mining operations, but in the new system it was felt desirable to remove the bottom coal left in certain parts of the mine. Instead of drilling holes in the coal, loading them, and fir- ing in the usual safe manner, five or six charges of dynamite were placed on top of the coal in each of several rooms; and while the men were at the mouth of the

Aug 1, 1929

By Hylton R. Brown

This publication, an abstract of a progress report covering an investigation of hazards in thermal coal-drying plants has been prepared according to the suggestions and recommendations of a committee6/ appointed by J. J. Forbes, Director of the Bureau of Mines, when the original report was reviewed at a meeting of representatives of the mining industry, operators of coal-drying plants, coal-mine workers, and the Bureau in Washington on May 6, 1955. The investigation on which the report is based was made in accordance with action taken at a previous conference in Washington on May 19, 1954, called by Director Forbes to consider what should be done to prevent explosions and fires in coal-drying plants. Scope of Investigation The investigation was planned to obtain information considered essential for properly appraising fire and explosion hazards in different types of coal driers. A questionnaire sent to Bureau personnel provided preliminary information on coal-drying facilities at more than 270 preparation plants. Information on methods used in operating different types of driers, with their furnaces, fans, cyclones, and other auxiliary equipment, was obtained by personal visits or conferences with the operators at 13 plants. Factual data on operating temperatures, composition of the drying gases, air flow, dust loading of the air or gas currents, use of water sprays, auxiliary air controls, and other factors were obtained by conducting full-scale tests at six different plants and making laboratory investigations with samples of dust and gas collected during the tests.

Jan 1, 1956

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By Robert G. Yewen, Ronald S. Conti

Underground mines rely on alarm systems, such as stench gas, audible or visual alarms, pager phones, telephones, and messengers to warn miners of a fire or other emergency. These systems are often slow, unreliable, and limited in mine coverage. This report describes the evaluation of a wireless signaling and warning system for underground mines. This system is applicable to both coal and noncoal mines. The work was conducted by the National Institute for Occupational Safety and Health in cooperation with TeleMagnetic Signalling Systems (TSS) under Cooperative3Research and Development Agreement No. BOM-CRDA-6200-0119. A TSS wireless ultra-low-frequency electromagnetic signaling system was installed at the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. A commercial smoke sensor was interfaced to a remote portable transmitter, and the alarm of the sensor was used to trigger the central evacuation and paging transmitter system during experimental mine fires. The underground/surface receivers flashed cap lamps and activated remote devices, such as strobe lights, within 30 to 40 s after the encoded signal was received. Evaluation results showed full-mine coverage of the electromagnetic field and that the encoded signal was received at the farthest point underground and on the surface perimeter.

Jan 5, 1997

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

By J. W. JOYCE

The Geophysical section of the United States Bureau of Mines has received many inquiries regarding the application of geophysical methods to the location of small, buried metallic objects. The object of this paper is fourfold: (1) To sketch as briefly and non- technically as possible the principles underlying the operation of several elec- trical geophysical methods of prospecting applicable to the finding of small, buried metallic objects; (2) to point out the possibilities and limitations of these methods; (3) to present, whenever possible, data showing actual results obtained from their use; and (4) to enumerate and describe methods that lack scientific background or foundation.

Oct 1, 1935

By Kris Chatrathi, John E. Going, Kenneth L. Cashdollar

Two types of flammability limits have been measured for various dusts in the Fike 1-m3 (1000-L) chamber and in the Pittsburgh Research Laboratory (PRL) 20-L chamber. The first limit is the minimum explosible concentration (MEC), which was measured at several ignition energies. In addition to the three dusts studied previously (bituminous coal, anthracite coal, and gilsonite), this work continues the effort by adding three additional dusts: RoRo93, lycopodium, and iron powder. These materials were chosen to extend the testing to non-coal materials as well as to a metallic dust. The new MEC data corroborate the previous observations that very strong ignitors can overdrive the ignition in the smaller 20-L chamber. Recommendations are given in regard to appropriate ignition energies to be used in the two chambers. The study also considered the other limiting component, oxygen. Limiting oxygen concentration (LOC) testing was performed in the same 20-L and 1-m3 vessels for gilsonite, bituminous coal, RoRo93, and aluminum dusts. The objective was to establish the protocol for testing at different volumes. A limited investigation was made into overdriving in the 20-L vessel. The LOC results tended to show slightly lower results for the smaller test volume. The results indicated that overdriving could occur and that ignition energies of 2.5 kJ in the 20-L vessel would yield comparable results to those in the 1- m3 vessel using 10.0 kJ. The studies also illustrate the importance of dust concentration on LOC determinations.

By J. W. Walkiewicz

One of the objectives of the Bureau of Mines is to develop substitution technology for scarce materials. In accordance with this goal, alloys containing lanthanum, cobalt, copper, and magnesium were investigated for fabrication of rare-earth-cobalt (RE-Co) permanent magnets. A complete substitution of lanthanum for samarium and a partial substitution of copper for cobalt was accomplished. Magnets of La-Co and La-Co-Cu-Mg alloys were fabricated by powder metallurgy techniques and evaluated. A maximum intrinsic coercivity of 23.2 kOe was obtained with a La-Co-Cu-Mg alloy. In comparison, maximum values of 9.3 kOe and 11.6 kOe were obtained with La-Co and La-Co-Cu alloys, respectively. The substitution of copper and magnesium for part of the cobalt resulted in a large increase of intrinsic coercivity, similar to the results of Bureau research with mischmetal-Co-Cu-Mg alloys. Unlike the mischmetal-Co-Cu-Mg magnets, the La-Co-Cu-Mg magnets showed signs of physical deterioration on exposure to air. The effects of fabrication parameters on the magnetic properties of the La-Co-Cu-Mg alloys were also determined.

Jan 1, 1982

By Ivette E. Torres

Table 8 provides data for the estimated value of world export trade of all mineral commodities from 1980 through 1991. It also provides a breakdown of the total into mineral fuels and non fuel minerals. These data have been developed from UN export trade data presented in table 9. The percent distribution and growth of the value of world export by major commodity groups are presented in tables 9, 10, and 11, respectively. In terms of industrial minerals (nonmetals), data in tables 10 and 11 include crude industrial minerals only, while table 8 includes an estimate for other industrial minerals. The 1991 estimates that appeared in the 1991 issues of this publication have been revised. It is typical for this section to review the year prior to the year of review because of the unavailability of data at the time of publication. The aggregated value of export trade in mineral commodities for 1992 was not available at the time of publication. The total value of nonfuel and fuel mineral exports for 1991 was about $616 billion in current (1991) dollars. The value of mineral fuel export trade accounted for about 53 % of the total mineral export trade. In 1980, the contribution of mineral fuel to the value of mineral commodity export trade had been almost 68%. The 1991 world mineral commodity export trade represents a 5.3% decrease (table 8) from that of 1990. The largest decrease was attributed to the decrease of export trade of fuel minerals (5%). The value of non fuel mineral export trade decreased by 4 %. Because the value export trade of all commodities increased by 1.2 %, the share of mineral commodities decreased from 19.2 % to 17.9 % of the total.

Jan 1, 1994

Increase the recycling of critical and strategic materials by simplifying the indentification and segregation of scrap. Background Because the United States is dl-most totally dependent on imports of such critical metals as chromium, cobalt and nickel, Bureau of Mines research has been directed towards conserving these metals by increasing the recycling of the complex scrap materials that contain them. Experienced scrap sorters, using the traditional techniques of object recognition, spark tests, chemical spot tests, color, apparent density, and magnetic properties, can adequately sort a wide variety of alloy groups. However, the complex nature of new materials entering the scrap market has made sorting both more difficult and more important. Some new alloys contain so many components that separation by discrete alloys becomes a prerequisite for effective recycling. The Bureau has completed Investigations on two methods for rapidly sorting complex scrap mixtures. One method uses a combination of two low-cost instruments. The other uses a single sorting instrument. Both approaches are reported.

Jan 1, 1986

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the Bureau of Mines to aerosol measurements in diesel equipped underground noncoal mines. The first technique is based on size selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately sub-micron in size while the mineral dust fraction of the aerosol is mostly super-micron in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size distribution data were modeled using a log-normal regression to parameterize the sub- and super-micron fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. For the mines visited, analysis of the size selective: samples yielded an average value for the fraction of the fine aerosol attributable.to mineral dust of 3 pct.'The CMB analysis, applied to both fractions of the respirable mine aerosol, yielded the amount contributed to each by the diesel· and dust aerosol sources. Less than 5 pct of the sub-microm fraction was mineral dust, however, as much as 20 pct of the diesel aerosol was found: ""in the super-micron fraction requiring a correction of the sub-micron fraction to account for the missing diesel mass. More accurate measurement will require a carbon specific analysis of the aerosol."

Jan 1, 1988