Search Documents

The coal deposits in Alaska occur in several major coal fields or basins. The deposits underlie about a quarter of the state, an area larger than Montana. Approximately 60 percent of the coal is bituminous and 40 percent is subbituminous. Less than one percent is lignite or anthracite. Although known coal reserves are estimated at only 6.1 billion tons (about 1.25 percent of U.S. reserves), estimates place the hypothetical reserves at 5.5 trillion tons and the identified reserves at 170 billion tons. The differences are due to limited exploration programs within the state. Conditions affecting mining and reclamation are unique to Alaska because of its extreme northern latitude. For example, permafrost occurs in about 75 percent of the state; tundra vegetation occupies vast treeless regions; and the climate is characterized by extremely cold winter weather and a short summer season. In addition, hydrologic conditions are considerably different from those in other states; major streams fed by silt-laden glacial melt water contain greater concentrations of natural sediment than the effluent discharge limits permitted by federal regulations. Also, some coal field locations are subject to potentially high seismic risk. These factors make coal mining and reclamation in Alaska more difficult than in other states. Alaska's program to regulate surface coal mining was approved May 2,1983. The Abandoned Mine Lands program was approved December 23,1983.

Jan 1, 1992

By L. Prosser, A. Iannacchione, G. Esterhuizen

The potential for roof falls in underground mines remains a clear and present danger for mine workers. An investigation of ground conditions in nearly 50% of the nation’s underground stone mines found that the state of roof stability is primarily determined in a limited and subjective manner. These large opening mines, with roof heights typically of 7 m or more, make physical observation difficult. Although some mines use monitoring techniques to gain additional information on roof stability, this practice is usually short-term and localized to address ground conditions in a particular section or part of the mine. A methodology to assess the risk for a roof fall is proposed in a preliminary fashion based on engineering judgment acquired from extensive underground stone mine experience and examination of related literature. The proposed method utilizes an observational technique to identify the risk of roof falls in three categories. Case study scenarios provide a realistic picture of model implementation. Providing the mine level decision maker with an accurate assessment tool to ascertain the level of risk related to ground conditions is expected to reduce mine worker injuries and fatalities. Moreover, the presences of danger can be overcome with a clear picture of quantified ground conditions.

By R. H. Grau

Improving the air quality in metal/nonmetal mines is important in protecting the health of miners. Air quality can be improved in metal/nonmetal mines by developing proper ventilation techniques. Mine ventilation systems require stoppings to direct the airflow and establish pressure differentials throughout the mine. Due to their large size, stoppings in large-opening mines are cumbersome and costly to construct and maintain. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) designed and tested two novel stoppings (Super Stopping and the EZ-Up Curtain Stopping) at its Lake Lynn Laboratory (LLL). The Super Stopping is designed as a long-term permanent stopping for use in the main entries of the mine, while the EZ-Up Curtain Stopping, although very durable, is designed more for portability and ease of installation. This paper describes the design, materials, and construction methods used for these stoppings as well as their performance and durability when subjected to tests simulating actual production face blast pressures.

Jan 1, 2006

By Hendrik Gerritsen

The research to be described is directed to the construction of an instrument that detects methane in air. The principle on which it is based is that methane gas absorbs infrared radiation in the wavelength range of about 3.2 to 3.4 micron. Solid state p-n junctions of composition In, .97Ca.03As emitting radiation in a band centered at 3.3 micron were grown by liquid epitaxy on InAs. Fight separate growth cycles and a total of 200 diodes were measured to determine total power, wavelength peak, spectral. half width and reproducibility of the method. In order to compensate for temperature changes, dual emitter systems (one InGaAs, and one InAs diode) mounted on the same TO-5 header were made. These devices were imaged, using a folded optical path cell, on large area InAs detectors, grown by a planar diffusion technique. In the 0-50°C range the primary temperature sensitivity is in the InAs detector rather than in the emitters. Several methods to reduce the overall temperature sensitivity to within acceptable limits were demonstrated. Humidity was shown to have a negligible effect on the measurements.

Jan 1, 1976

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C. 4 Hoist Assemblies (not man-rated) A large number of manufacturers supply materials handling winches. These units are predominately electric powered while a limited number of vendors supply air powered equipment. Air powered units are currently used extensively for underground materials handling purposes. Suppliers of materials handling equipment normally include a disclaimer statement in their published literature which clearly states that the equipment "is not designed or suitable for lifting or lowering persons " This category of commercially available equipment can be adequate for emergency man hoisting provided that its' capacity is suitably derated and provided also that the necessary safety features are incorporated. Section C. 5 details the equipment which could be added to a commercial materials hoist to meet these needs. Four commercially available hoist assemblies, two electric and two pneumatic are discussed in the following paragraphs. This equipment is typical of what is commercially available and three of the units are currently used extensively in mining applications. Each hoist description includes a remarks paragraph which identifies the additional equipment each hoist would require for emergency hoist use.

Jan 1, 1976

By G. E. McElroy, D. Harrington

The use of shall electrically- driven fans , in conjunction with air- pipe of various diameters is becoming of increasing importance for the ventilation of working places in metal mines through which the general ventilating currents can not be coursed . It will probably continue to increase in importance since the concept that air motion is the most important factor in maintaining comfort in hot ( above 80° F . ) working places is more generally accepted , and as the inefficiency and greater expense of attempting to ventilate such places with compressed air is recognized . Managers of large properties can afford to experiment with fan- pipe installations until types are found that meet their conditions , but managers of shall properties , unless forced to it by extreme conditions , prefer to wait until they can obtain data sufficient to guarantee at least a measure of success from such installations . At present , such data , even in part , are available to only a few (mainly fan manufacturer's representatives , consulting ventilation engineers , and ventilatin engineers employed by large companies ) , and important recent developments are mostly of a confidential nature . One large metal - mining company cooperated with a fan manufacturer in some extensive experimental work on small blowers and found that instead of using stock fans , considerable power economy could be effected and equal quantities of air delivered by use of or 2/3 width fans with small motors rather than using stock fans and larger motors ; it was also found advisable to adopt certain sizes of tubing for certain lengths of run . In fact , many important facts were ascertained in this study , and it is now promised that they will soon be given to the public . It is true that a certain amount of data on industrial installations are available , but such data are only in part applicable to metal -mine conditions , because , until recently , little attention has been given to ventilation in metalmines , and the conditions encountered usually require a greater length of pipe , a more temporary type of construction , and closer attention to temperature control than the ordinary run of industrial installations demands ..

Feb 1, 1922

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

By Erica E. Hall, Robert H. Peters, Charles Vaught, Jon C. Volkwein

Coal workers’ pneumoconiosis is the leading cause of death due to occupational illness among U.S. coal miners. This disease is caused by miners’ exposure to excessive levels of respirable coal mine dust. A personal dust monitor (PDM) has recently been developed to provide near real-time feedback to miners regarding the level of respirable coal dust in the air they breathe. The main objective of this report is to document coal miners’ reactions to this device and how they make use of the information it provides. It summarizes a field study by the National Institute for Occupational Safety and Health that documented the opinions of 30 miners at 4 underground coal mines concerning the use of PDMs.

Jan 2, 2008

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By James J. Olson

The Bureau of Mines recorded peak particle-velocity levels and vibration frequencies to determine the nature and intensity of ground vibrations for tunnel blast rounds at the NORAD Complex, Colorado Springs, Colo. Previous Bureau of Mines studies in quarries and underground mines had shown that scaling (dividing) the distance from the blast by the square root of the charge weight removed the effect of the various charge weights on vibration amplitudes. The analysis of variance tests performed on the NORAD vibration data, however, indicated that the cube rather than square root scaling exponent grouped the data more effectively. The empirical propagation equation, V = 560 (D/w1/3)-2.04, where V is the maximum peak particle velocity in inches per second, D is the distance from the blast in feet, and W is the zero-delay charge weight in pounds described the attenuation, with distance, of the particle velocities from the tunnel blasts in the Pikes Peak Granite of the NORAD Complex.

Jan 1, 1972

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

Strategies for monitoring methane levels during roof bolting in an extended cut entry were evaluated. Testing was conducted at the Pittsburgh Research Laboratory’s methane test gallery. Operating conditions were varied and methane releases at the face and drill holes were simulated. Methane readings were taken at the face, and at locations outby the face. Results show that, when the major source of methane was at the drill holes, the highest methane readings were at locations on or 6.1 m (20ft) inby the bolting machine. Methods for selecting better outby sampling locations, when the majority of the methane is released at the face, are examined. During roof bolting it is easier to sample at these outby locations rather than at the face. Further testing is needed to determine what relationship exists between methane concentrations at the outby locations and at the source of the methane release.

Minimize the risk of conveyor belt fires in underground coal mines by improving the accuracy of and means by which flammability data are acquired. Approach Develop a large, laboratory-scale flammability test for mine conveyor belting that realistically assesses its fire resistance. Background A conveyor belt fire in an underground coal mine is a serious threat to life and property. To minimize the risk of belt fires, the U.S. Code of Federal Regulations (CFR) for underground coal mines requires approved fire-resistant belting. Despite this precaution, about 25% of the reportable underground coal mine fires from 1983 through 1988 involved conveyor belting. In several instances, hundreds of feet of belting were destroyed. The current flammability test for fire-resistant belting is specified in 30 CFR, Part 18.65 and is conducted by (be Mine Safety and Health Administration (MSHA). The small-scale test is performed in a 21-in-cubical chamber with 6-in-long by 1/2-in-wide belt samples. To evaluate the flammability of conveyor belting under more realistic conditions, the U.S. Bureau of Mines conducted large-scale fire tests of belting. The large-scale data were then utilized in the development of an improved laboratory-scale flame test for fire-resistant belting.

Jan 1, 1991

By Wing G. Agnew, John A. Johnson, McHenry Mosier

"INTRODUCTION AND CONCLUSIONSThe first three reports of investigations 5/ in this series, pertaining to the investigation of stemming at the Mount Weather Testing Adit dealt with the dust produced by blasting, the effect of stemming on gases generated by blasting, and the relative advantages and disadvantages of different types of stemming and no stemming when used with 60-percent ammonia gelatin dynamite.This report covers an investigation of the length of stemming material through which a primer will fire and detonate a charge of dynamite, such as a missed hole.The practice of drilling a new hole a foot from a missed hole to blast out the missed hole should be prohibited. It is dangerous, as is evidenced by the number of miners killed through drilling into missed holes. It is even more hazardous in a mine on a multiple-shift basis, in which the same miners do not drill succeeding rounds."

May 1, 1942

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

By R. V. Ramani, R. Bhaskar

"An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner.The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inertial impaction, The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size depend,From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models for dust-flow in mines, a series of dust flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. In this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.The major factor affecting ambient dust concentration in mine airways is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian diffusion, eddy diffusion and inertial impaction. The major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. Inertial impaction is significant only during changes in direction, but the change in direction of flow with resultant powerful eddies may cause increased re-entrainment of the particles, thus having a compensating effect. While the literature in aerosol sciences contain several references on deposition, most studies were done in small diameter tubes for diffusional deposition (Liu and Agarwal, 1974). The deposition data from small diameter, short tube experiments may not be applicable to studying deposition in mine airways that have large areas and extend several hundred meters. Further, the change in concentration along the length of a mine airway may significantly affect the deposition, an aspect that may not be easily determined in short tubes in laboratory experiments."

Mar 1, 1992

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

Allow miners to communicate via the pagerphone system when they are not near one of the phones. Approach A small lightweight pagerphone, having crocodile clips which pierce the phone line insulation, was developed. How It Works The Portable Telephone/Intercom is temporarily clipped onto an existing pagerphone line at any location, and operated like an intercom. It is riot necessary to strip the insulation from the pagerphone line to make the connection. In addition to the clips for connecting to pagerphone line, the Portable Telephone/Intercom consists of a small belt-carried control box, an ear-phone, and a bone-conduction microphone which is attached to the webbing in a miner's helmet. All together, these components weigh only 20 ounces including the batteries

Jan 1, 1977

Reduce face methane concentrations and help prevent miners from working under unsupported roof while moving the curtain. Approach Use water sprays on the continuous mining machine to move and direct air to the face, and also provide appropriate installation guidelines for the most effective use of the system. I n laboratory tests and under actual mining conditions, the spray fan has proved an effective means of ventilation. Recent observations in the field, however, have shown that not enough technical information is widely available on proper installation of the spray fan. This Technology News is designed to rectify that situation by providing a concise guide for spray fan installation. How the System Works Good ventilation is essential for methane control. The spray fan system repositions regular water sprays to help the normal exhaust face ventilation do a more effective job. The various water sprays help in many ways: 1. Side sprays bring clean air along the side of the miner into the off-curtain corner.

Jan 1, 1983

By R. V. Ramani, C. B. Manula, A. Owili-Eger

That a close analogy exists between the flow of air in mines and the flow of current in electrical networks- has been known for a long time. The laws that have been used to solve series and parallel electrical circuits have been used to solve for the equivalent resistance in mine ventilation problems. Kirchhoff's current and voltage laws have also been adopted in solving mine ventilation network problems. It will be best to define a few terms here regarding networks, and with reference to Figure 1, these definitions can be elucidated. Figure 1 can be represented by the network in Figure 2 without losing any essential details. 1. A junction is a point where two or more airways meet. 2. The segment of a roadway connecting any two junctions is known as a branch. 3. A mesh is a closed path through the network. In the above network, B, C, D and F are the junctions, CF and CD are two of the branches and CFDC is a mesh. Kirchhoff's current law states that the sum of currents entering a junction. Applying this law to the junctions in the ventilation network, one obtains for junctions C and F, the following relationships: JUNCTION C: Q1 = Q4 + Q3 (1) JUNCTION F: Q2 + Q3 = Q5 (2) Similar relationships can be drawn for other junctions. Kirchhoff's voltage law states that in any complete electric circuit, the algebraic sum of the emf's must equal the algebraic sum of the voltage drops. In mine ventilation, the square law (Atkinson's

Jan 1, 1975

By Steven J. Page

Overexposure to airborne respirable crystalline silica dust can cause disabling or fatal respiratory disease, and mine worker exposure to silica dust continues to be an ongoing occupational health concern. Exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern. On surface coal mine drills, bailing air flushes the cuttings out of the drill hole. Conveyor belting material is typically used to fabricate a shroud around the drill deck in an effort to contain the drill dust so that it can be captured by a collector. Dust leakage from the drill shroud is usually the worst dust source problem on most drills. The focus of this work is drill shroud dust leakage and the relationships of various drill parameters on this leakage. Experimental data were obtained and used in combination with dimensional analysis to establish these relationships. In general, it is found that airborne respirable dust (ARD) concentrations vary in a direct relationship with shroud leakage area and in an inverse relationship with drill deck cross sectional area and shroud height. This work expands the testing and dimensional analysis previously reported for collector/bailing air flow ratios ranging from 2:1 to 4:1 to include ratios approaching 1:1. A semi empirical mathematical model has been developed and expanded to describe ARD generation on surface coal mine drills. Geometric parameters included are drill deck height and cross sectional area, shroud leakage associated with the deck shroud, and the operational parameters of bailing airflow and dust collector airflow. The relationships can be described by logarithmic functions and yield predictive ARD values, which fall in the range measured on operating drills for collector/bailing air flow ratios greater than 2. However, at values of collector/bailing air flow ratios of approximately 1.1, the amount of ARD shows minimal response, if any, to drill deck shroud improvements that do not result in near perfect seals. This is a condition that can occur in actual operation and is a substantially different result than previously expected and reported. Application of these results should provide mine operators with sufficient information to determine (1) the relative magnitude of their dust emissions, (2) where they should focus their efforts to reduce ARD emissions and (3) the improvement they could reasonably expect to achieve. Given that exposures of surface coal mine rock drillers to respirable crystalline silica are of particular concern, substantial reductions of airborne silica dust during drilling may be estimated and achieved through use of the analysis presented. Keywords: drill; dust; model; dimensional analysis

Jan 1, 2008