Search Documents

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization, and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available? in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number 50241073 by Fenix & Scisson, Inc. to the Denver Mining Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

An accelerated and coordinated program of coal research is believed by many to be a necessary step in assuring coal's proper position in the expanding energy market. The President's Advisory Committee on Energy Supplies and Resources Policy, for example, made the following recommendation: We recognize that coal is a great national asset and endorse a cooperative study to determine what research and development could be undertaken. The coal industry and both Federal and State Governments should participate in this study and its costs. Representatives of the coal industry have agreed that such a study should be initiated. Accordingly, Felix E. Wormser, Assistant Secretary - Mineral Resources, United States Department of the Interior, requested the Bureau of Mines and Bituminous Coal Research, Inc., to conduct a survey of current research on bituminous coal. In addition to this survey, studies were made to determine research projects that would be of value to the coal industry.

Jan 1, 1956

Endless lines at service station gasoline pumps, limited travel at reduced speeds, thermostats set at an uncozy sixty-eight degrees in the dead of winter-these are but a few of the inconveniences and discomforts that awakened Americans to a realization that our domestic minerals resources, traditionally taken for granted, are not boundless. We begin to accept and practice principles of conservation, yet we are aware that this alone cannot appreciably forestall the inevitable depletion of our minerals, metals, and fossil fuels-resources critical to our Nation's economy. The key to warding off shortages is the development of technology that will insure a continuing, adequate supply of minerals and energy from reliable sources at the lowest possible costs to society and the environment. The mission of the Bureau of Mines is to develop this improved technology. Established in 1910, the Bureau of Mines of the Department of the Interior is the Federal Government's primary research arm in the minerals and fossil fuels fields. In addition to its research role, the Bureau keeps the Government informed of the Nation's mineral posture. The Bureau also seeks to stimulate private industry, through the awarding of grants and contracts, to produce minerals and fuels at a rate compatible with the country's increasing demands.

Jan 1, 1974

By A. M. Cummings

Each mining district presents different problems as to the methods of ore extraction cad underground support, which are dependent upon the type of the ore deposit and the character of the inclosing rock. Mining costs, however, depend largely aeon the efficiency with which the methods employed underground are [applie] as well as upon the selection of the method best adapted to the physical conditions. The purpose of this paper is to present to the operator in other districts a detailed description of ho mining method used ins results obtained in tie exploitation of the bedded magnetite deposits of the Mineville district. The town of Mineville is situated in the Adirondacks, five miles west of Port Henry on Lake Champlain.

Jan 1, 1928

By Robert H. King

An analysis of low-voltage shielded trailing cables is performed to develop a method for calculating the differences in operating costs between shielded and non-shielded cables. Two types of shield constructions are considered (SH-C and SH-D) for the three major underground coal mining methods. Data from laboratory and in-mine testing are presented in addition to an analysis of safety benefits. Recommendations for further investigations are proposed. Example calculations with sensitivity analyses are presented. Recommendations for further investigation include costs impact considerations.

Jan 1, 1980

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By H. Winkelmann

The author, who himself has worked inn the field with various types of torsion balances, expresses in the article his experience with the recently marketed Haff-Torsion-Balance. The advantages of practical work with Haff?s s torsion balance as compared with other types are mentioned. In spite of low weight and corresponding small dimensions (Model M = 23.5 kg., Model Al = 11.5 kg.) the sensitiveness is not less than that in the largest instruments. It is at 1.10-9, which is proved by calculations. A comparison with the corresponding values of other types of torsion balances (Eötvös, Askania, Gepege) is given. The mechanical features of the instrument are briefly described, and the balance is illustrated by a, cross section of it. -- W. Ayvazoglou. DETERMINATION OF THE ELEMENTS OF THE MAGNETIC AND GRAVITATIONAL FIELDS INDUCED BY AN INFINITELY LONG HOMOGENEOUS CYLINDER By G. A. Gamburzeff Gerlands Beiträge zur Geophysik, Band 19, Heft 2/3 Leipzig, 1928, pp. 210-230. The present work is a. contribution to the quastion of the reason for the magnetic and gravitational anomalies in the government of Kursk (Russia).

Jan 1, 1929

By D. Harrington

Educational campaigns conducted by the manufacturers of explosives, the Bureau of Mines, mining companies, and safety organizations have contributed greatly in reducing accidents caused by explosives arid blasting. Despite these campaigns and the dissemination of information, accidents from explosives and blasting continue to be the direct cause of scores of fatalities and hundreds of nonfatal accidents annually, not only in the mineral industry but essentially wherever explosives are used. The experience of many mining companies and other users of explosives has proved that accidents from explosives can be prevented or averted by the proper training of employees in the handling and using of explosives and by the enforcement of definite rules and instructions for their use. Unfortunately, throughout the years numerous false impressions and ideas have grown up and around the use of explosives. Many of these can be traced back to the manner in which the users of explosives were originally taught, if instructed at all; and as with many types of misinformation in nearly all walks of life, those false ideas are decidedly persistent and being so cause much damage. Many if not most of the users of explosives gained their knowledge of explosives and blasting by watching others and more or less "absorbing" the procedures and thrones of the other fellow, who acted unconsciously as teacher or instructor. A study of explosives accidents reveals the results of such "teachings" when the causes of the accidents are determined, and as might be expected the results very often are far from good. One of the most persistently erroneous impressions or ideas is concerned with the burning rate of safety fuse. Many men with

Jan 1, 1944

By R. Karl Zipf, Francois E. Heuze

Stress analysis programs such as MULSIM/NL, LAMODEL, MinSim 2000, and EXAMINETAB are used in the mining industry to analyze stresses and displacements in coal mines, platinum mines, gold reefs, and tabular-type deposits. These relatively simple numerical models can efficiently simulate yielding and failure of a rock mass near a mine opening and subsequent stress transfer. The main input parameters for these models are a family of nonlinear stress-strain curves for the in-seam material. For many applications of these models, such as in coal mining, extensive field measurements and observations exist from which to estimate these stress-strain curves and calibrate the numerical models; however, such measurements are lacking for other types of mines. A three-step method is presented to determine nonlinear stress-strain curves for boundary-element (BE) programs used in many mining applications. The method requires a suite of laboratory-scale strength tests at various confining pressures. Note that this analysis uses laboratory-measured strength and modulus properties of alluvium. The dependency of the mechanical properties of alluvium on scale has not been established, although more tests are being planned. However, it is believed that the relative comparisons performed are valuable regardless of scale effects. First, the FLAC2D computer program is used to model the laboratory tests and determine cohesion (c) and friction angle () for a Mohr-Coulomb material model. Second, another FLAC2D model uses the c and values to calculate vertical stress and strain around a single opening in the rock mass. This model calculates the stress-strain path of points at various distances from the opening boundary. Finally, based on these stress-strain paths, the stress-strain curves needed for a BE analysis are derived. This three-step method was demonstrated in a large, flat-lying underground test facility in very weak rock. The BE analyses agreed well with observations of failure at the test facility and provided a basis for evaluating the behavior of alternative layouts.

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By A. E. Kasten

The contract objective was to develop and test automatic fire control systems for large surface machinery in surface coal mines. The effort described by the report covers the period from 31 January 1977 to 11 November 1977 and accomplished the following tasks: ? Data accumulation, mainly from visits to the major manufacturers and mine sites. ? Hazard analysis of blast-hole drill, mining shovel, and dragline. ? Recommended design concepts for automatic fire control systems for each of these vehicles. ? Detail system designs for each of these vehicles. ? Procurement of prototype systems for the blast-hole drill and mining shovel. ? Installation of the prototype systems on machines at a surface mine and demonstra¬tion of performance by fire tests on the machines.

Jan 1, 1977

By P. S. Haury

"INTRODUCTION Preliminary examinations of the Mohawk zinc prospect were made by John 14. Price and the author in July, August, and September 1943. Considerable quantities of oxidized lead and zinc minerals were found in old shallow work¬ings along two faults - one an over thrust fault with Paleozoic limestone in the hanging wall overlying Cretaceous shale and arkose in the footwall of the fault, and the other a bedding fault in the Paleozoic limestone.The chances appeared good for finding important lead-zinc sulfide ore bodies at 200 to 300 feet beneath the surface, so exploration in three steps by the Bureau was recommended:Surveying, mapping, and character sampling of the outcrops with topographic and geologic mapping of the immediately surrounding area.Preliminary drilling of four test holes, aggregating about 1,500 feet, to locate the top of a possible sulfide ore zone and determine the thickness and intensity of the sulfide mineralization.Contingent upon favorable results of the second step, diamond drilling of about 6,300 feet of additional hole to explore the sulfide ore bodies.The outcrops were surveyed and sampled, a topographic map was made of the area, and the geology was mapped. A project was set up for preliminary drilling of step 2 in the fiscal year 1944-45. An access road to the drill sites was built in April 1945. Diamond drilling was started on April 28 and completed on September 25, 1945, under the supervision or the Bureau of Mines. The exploratory work is covered in this report."

Oct 1, 1946

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for Zambia for the period from 1970 through 1981. The work done through the Bureau of' Mines, Minerals Availability Program, under Contract number J0225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) timber and lumber, 6) fuel, 7) powder and blasting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples tom some oil fields of Louisiana are given in Bulletin 291.4/ Analyses of 26 representative crude oils from various producing formations of southern Louisiana are given in is report. These.samples are from 14 field's in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area." ACKNOWLEDGMENTS Thanks are due the representatives of the various companies from whom samples were obtained for their cooperation and assistance in helping to secure representative samples. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1934

By C. W. Owings

"PURPOSE OF REPORTMany bituminous coal-mine officials realize that coal dust presents an ever-present coal-mine explosion hazard, and that persons forced to breathe large quantities of it may be more subject to respiratory infection than persons working in less dusty atmospheres. As an outgrowth of the realization that coal dust should be allayed at its source, many mining companies have expressed the desire to install dust-allaying equipment, and in a number of mines, water or wetting solution is being applied on the cutter bars of mining machines, on mobile loaders, belts or conveyors underground, and tops of mine cars. Spraying equipment also has been installed on dumps to allay dust during dumping operations. Dust-allaying equipment has not been standardized, however, because manufacturers have found that many prospective purchasers of such equipment have different ideas. These manufacturers wish to standardize, so far as feasible, the types and placement of such equipment. Many mine officials, although interested, do not know the best or most effective methods for allaying dust.For a number of years the Bureau of Mines has advocated allaying dust by applying water or, more recently, water modified by a wetting agent on the cutter bar of mining machines and by applying water to loaded and empty mine cars in order to keep as much dust as possible from spilling onto the haulage roads. In recent years this Bureau has also advocated applying water with or without a wetting agent during mechanical loading of coal and during unloading of coal from trackless cars or buggies and from elevating conveyors. It has now become apparent that specific arrangement of pipes, hose, and nozzles should be standardized to at least some extent. It is the purpose of this report, therefore, to give in detail suggested arrangement of dust-allaying equipment in the hope that both manufacturers and mine officials will have available dust-allaying equipment with maximum efficiency to do the desired work."

Nov 1, 1945

By Alvin Schallis

The. problem of supplying enough magnesia for the American war effort has become highly important. Before hostilities began, only about two-thirds of our, require vents came from domestic sources; now they must supply almost all the magnesia we need. A further burden is placed upon our own supply by the fact that more and more magnesia is being required, not alone to pace the war tempo of general industrial activity, but also to replace chrome ore in refractories and to make magnesium metal. The domestic magnesite and brucite industry is equipping itself to satisfy much of this greater demand for magnesia, but the remainder must be obtained elsewhere. The principal sources of magnesia are magnesite, brucite, dolomite or high-magnesium limestone, natural brines, sea water, salt-works bitterns, magnesium silicates, and magnesium salts. Although dolomite is tae subject of this paper, it should be considered in perspective with all these highly competitive sources of magnesia.

Jan 1, 1943

This manual provides instructions for installing, operating, and maintaining a protective canopy on the Joy Mfg. Co. shuttle car. These instructions are based upon actual installations made in the mine on two shuttle cars, model 21SC-2E. The parts list and engineering drawings for the protective canopy are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other shuttle cars with similar protective canopies. Skilled mechanics can determine if the instructions hexein would he applicable to the other shuttle cars and can determine any necessary modifications if they are not.

Jan 1, 1973

By R. Wiebe

During a recent investigation the authors were interested in determining: (1.) How many points were necessary to locate the deviation curve for copper-constantan thermocouples within an accuracy of about 0.05° C., used in connection with the "standard" thermocouple of L. H. Adams. (2.) Whether copper-constantan thermocouples showing considerable deviations from the "standard' were consistent throughout their calibration. (3.) How reliable the extrapolated portion is - that is, the interval between -183 and -220° C. of the "standard" thermocouple. It seems that a calibration between 0 and -193° C. can be made within the stated accuracy by determining experimentally the e.m.f. of the particular couple at -78.50°, the normal sublimation point of carbon dioxide, and at -182.97°, the normal boiling point of oxygen. Substituting the values found for the two fixed points in the simple quadratic. Equation

Jan 1, 1931