Search Documents

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator's position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973

By John C. Edwards

Several experimental programs were conducted at the Pittsburgh Research Center to investigate the level of mine fire detection and alarm capability possible using state-of-the-art technology. These programs involved comparison of the response and alarm time of optical and ionization type smoke sensors to smoldering and flaming coal combustion in a smoke chamber. Coal combustion experiments conducted in the smoke chamber demonstrated that a CO concentration of 5 ppm above ambient corresponded to an optical density of 0.022m1. For the four smoke sensors for which a continuous analog signal was available, a smoke sensor alarm was defined as the average background signal plus ten times the peak-to-peak noise. This alarm criterion resulted in the association of the alarm for three of the four sensors with a smoke optical density of 0.022m-1. and 0.033m-1 for the fourth smoke sensor. The smoke sensors used in the smoke chamber studies were incorporated into large scale diesel fuel fire experiments conducted under normal ventilation conditions in the Safety Research Coal Mine (SRCM) at the Pittsburgh Research Center. These experiments showed that a diffusion mode smoke sensor alarmed earlier than a diffusion mode CO sensor; and, based upon the measurement of the optical transmission at the location of a pump mode ionization type smoke sensor that a pump mode ionization smoke sensor alarmed at an average smoke optical density of 0.021m" for the twelve experiments conducted. A series of 30 and 330 kW diesel fuel fire intensity experiments were conducted under zero airflow conditions in the SRCM. It was determined that :(I) thermal sensors are inadequate at 30 m from a 300 kW fire;(2) a diffusion mode ionization smoke sensor can be more effective for mine fire detection than a diffusion mode CO sensor;(3) recommendations can be made for sensor spacing in a mine entry based upon the measured CO buoyancy induced spread rates along the mine roof and the time for a developing coal fire to ignite a conveyor belt.

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 1993

By C. H. Elder

An experimental degasification program using a vertical borehole and vacuum pump to drain gas from the gob area of a longwall panel was successful at Bethlehem Mines Corporation, Cambria Division, No. 33 coal mine. Sixty-one million cubic feet of methane has been exhausted during a 9-month period. Daily production time in the panel increased as a result of lower methane levels in the returns. Removal of large quantities of methane in this way and the exclusion of it from the ventilating system will provide reduced cost in mine ventilation and provide a safer environment for the mine.

May 1, 1969

By E. G. King

Heats of formation of three crystalline oxides of rhenium (Re02, ReO3 and Re207) have been determined by the method of solution calorimetry, using an aqueous perchloric acid--ceric perchlorate solvent. Copper metal and cupric oxide were utilized as auxiliary substances. Heats were determined at 298' K for the reactions Re + 2CuO = Re02 + 2Cu, Re + 3CuO = ReO3 + 3Cu, and 2Re + 7CuO = Re207 + 7Cu. Standard heats of formation were derived using the value of -37.23 ±0,15 kcal/mole as the heat of formation of CuO. The standard molal heats of formation of the rhenium oxides were determined: Re02, -107.3 ±0.8 kcal; ReO3, -140.8 ±0.9 kcal; and Re207, -301.9 ±1.8 kcal.

Jan 1, 1969

By C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By F. N. Kissell, R. J. Bielicki

The Bureau of Mines found sulfur hexafluoride (SF6), released from a lecture bottle, to be an ideal gaseous tracer for studying mine ventilation systems. Air samples were collected in glass syringes and analyzed by electron-capture gas chromatography. In these studies, the lower limit of detection was about 1 part per billion by volume (ppb) of SF6 per part of air. Experiments conducted in a Pennsylvania limestone mine showed this technique useful in evaluating the effectiveness of auxiliary fans, measuring low flow velocities, probing the air circulating near a working face region where ventilation appeared to be poor, and estimating volumetric flow rates in airways of large cross-sectional area and having low flow velocities. This technique was also used in a western vein-type metal mine to measure the amount of return air being recirculated into the intake air due to leakage through old stoped areas.

Jan 1, 1974

By Gertrude N. Greenspoon

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) held public hearings in early 1975 on proposed standards for exposure to inorganic arsenic. The findings obtained at the hearings will be considered to promulgate emission standards. Domestic Production.-Arsenic trioxide (As203) was produced domestically only at the Tacoma, Wash. copper smelter of ASARCO Incorporated. Production data cannot be published. Output rose 9% over that of 1974, shipments were less than half those of 1974, and stocks rose 31 %. Production of arsenic metal, begun by ASARCO in August 1974, continued in 1975.

Jan 1, 1977

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

By Jerry L. Huiatt

An accurate and reproducible procedure was developed using the gas-liquid chromatograph to quantitatively measure oleic acid on flotation products and in flotation water phases. The method comprised extraction of the oleic acid from the mineral surfaces with alcoholic NaOH, esterification of the extracted oleate, and chromatography of the methyl ester with an internal standard. Quantitative analysis of oleic acid on flotation products from test tube and bench-scale flotation tests with pure minerals and with natural ores proved the applicability of the method on a variety of minerals. The accountability of oleic acid added was 100 percent, ±5 percent.

Jan 1, 1968

By Mark A. Ackerson, Kenneth E. Hjelmstad

An ideal fire warning alarm system for underground mines would be low cost, convenient, fast, reliable, and able to warn all underground workers. Present warning systems, such as phones, messengers, and stench, fail one or more of these criteria. The U.S. Bureau of Mines may have devised the ideal system. The one way communication system employs a large loop antenna and transmitter to create a 630 hertz (Hz) electromagnetic field to send information through-the-earth to cap lamp battery mounted micro- receivers worn by underground miners. Field tests of prototype equipment in 1986 resulted in through-the- rock signal transmission of over 762 m (2500 ft). Subsequent hardware upgrades for more recent tests resulted in transmissions of over one mile. Recently developed receiver circuitry employs phase- locked-loop detection circuitry responsive only to a specific series of pulses of given time duration, that eliminates false alarms from electromagnetic noise emitted by mine equipment, power lines, or lightning. A multichannel system can relay standard messages to miners

By Tobias W. Goodman, Joseph Cervik

This Bureau of Mines report investigates the horizontal trajectory of boreholes drilled in coalbeds using the rotary drilling technique. Test holes drilled in coalbeds showed that the path of a borehole in the horizontal plane depends on drilling assembly configuration, drill bit rotation, and coalbed geologic features. An assembly that contained an 18-ft (5.53) long drill collar and two centralizers had the best horizontal stability evidenced by trajectories that deviated less than 16 ft (4.9 m) from a target at 1,000 ft (305 m). Removal of one of the centralizers resulted in a loss of control of hole trajectory in the horizontal plane. Generally, holes tended to turn to the right, presumably because of right-hand rotation of the bit. Deviations from the original bearing line were as much as 200 ft (61 m) or more at a depth of 1,000 ft (305 m).

Jan 1, 1988

By George R. Schottler

The Bureau of Mines investigated the distribution of uranium and various methods of ore sampling in a uranium deposit typical of those in the Morrison Formation sandstone of the Ambrosia Lake area, Grants mining district, north-western New Mexico. Chemical and radiometric assays of diamond-drill core samples are compared in detail by statistical techniques, and the assay data are correlated with the stratigraphy of the deposit. Conclusions applicable to ore-reserve estimation in geologically similar uranium deposits are drawn.

Jan 1, 1971

By Arnold M. Lansche

Domestic Production.-Domestic production of white arsenic, AS,03, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. The Anaconda Company discontinued production of white arsenic in 1965. Arsenic metal was not produced. Consumption and Uses.-Most of the white arsenic produced in 1965 was consumed in manufacturing lead and calcium arsenate insecticides.

Jan 1, 1966

By Marvin L. Whisman

A radiotracer technique developed by the Bureau of Mines extends to the parts-per-billion range the sensitivity for determining contributors of deposits formed in stored and thermally stressed jet fuels. The method depends upon measuring radioactivity associated with thermally induced deposits from fuels containing one labeled compound. The technique was applied to 88 test blends, representing 12 fuels and nine carbon-l4 labeled fuel constituents or fuel additives, or both. Data from results of these tests are included in this report. With this radiotracer technique, the contribution of fuel components and additives to thermally induced deposits in a variety of fuel environments was estimated before and after storage.

Jan 1, 1969

By Stephen P. Signer

This paper presents an overview of laboratory and field tests on approximately 250 fully grouted roof bolts instrumented with strain gauges in order to study loading behavior. Laboratory work included pull tests, time-dependent tests, and shear tests. The field tests were conducted in 14 different mines extracting different commodities. However, because of the focus of this publication, only the results of tests in 9 coal mines are reported here. In the field tests, all but 14 bolts were loaded by rock movement; these 14 bolts were tested using pull gear. The variables studied included anchorage length, mechanical interlock, time-dependent behavior, shear, installation load, loading rate, and maximum load level. Such information will improve the understanding of the behavior of resin-grouted bolts, which in return will enhance the safety of miners by reducing the occurrence of rock falls. The influences of geology, overburden depth, entry width, mining-induced stresses, and bolt spacing are not described.

Jan 10, 2000

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

By Jack C. White

The purpose of this Bureau of Mines work was to develop information useful in improving copper recovery during copper milling operations. Eleven copper mill tailings from the Western United States were subjected to froth flotation and cyanide leaching to provide an experimental basis for comparing their beneficiation response. Recoveries in flotation concentrates made from mill tailings ranged from 65 to 15 percent, at copper grades of 13 and 2.2 percent, respectively. Liberated copper sulfide minerals present in two samples were readily recovered by laboratory froth flotation. Nine of the samples were less amenable to froth flotation because of physical locking between copper sulfide minerals and gangue. Correlations among tailings indicated that recovery of sulfide copper by flotation was directly related to the sulfide copper content. Empirical equations derived from flotation data provided average values for unrecoverable copper and for recovery efficiency. Flotation response of copper mill tailings may be predicted from the equations. Data from cyanide leaching provides an equation describing the limiting high values for removal of copper by this method.

Jan 1, 1974

By Yael Miron

Ammonium nitrate-fuel oil (AN-FO) mixtures are used as blasting agents in mining pyrite-bearing ores. The temperature of these ores can increase by the continuous, though at times slow, oxidation weathering of the pyrites. At elevated temperatures, AN-FO reacts exothermally with pyrite, and the reaction becomes self-sustained at 120° C ± 10° C. The Bureau of Mines has conducted an investigation to determine the reactivity of mixtures of AN-FO with pyrite containing ferrous sulfate. The results of tests in a heated vessel simulating a hot borehole demonstrate that small amounts of ferrous sulfate, a major product of pyrite weathering, initiate a self-sustained exothermic reaction with AN-FO at 80° C. Five pct by weight of urea was found sufficient to prevent a reaction among the three ingredients, at least within the limits of the test, which reached 180° C. Smaller amounts of urea and of potassium oxalate slowed down the reaction and delayed its onset to higher temperatures, but did not prevent it.

Jan 1, 1979