Search Documents

By James M. Baugher, Donald W. Conrad, William J. Wiehagen

This report describes a process for quickly developing information that is useful for skills training. The process is called job training analysis (JTA). Its main use is to structure skills training at the jobsite. JTA supports structured skills training by identifying the job duties, tasks, and steps and the reasons why those job components are important. The outcome of the JTA process is a worksheet—a training outline based on the knowledge and expertise of experienced workers. Time invested in developing a JTA will result in significantly more time saved when it is used appropriately by skilled trainers. Like a roadmap, JTA saves time and energy. Experimental work at several mine sites helped document, refine, and validate the JTA process. JTAs for two mining jobs—roof bolting and lift truck operation—at two different mine sites are used to illustrate some of the concepts and the specific JTA process described in this report. The work at these two sites was influenced by cooperative work between the Mine Safety and Health Administration (MSHA) and the National Institute for Occupational Safety and Health (NIOSH) at several other mine sites and prior collaborative work with the U.S. Navy. The mining JTA process is grounded within the military research on the design of instructional systems. MSHA and NIOSH worked to simplify and apply the military training development model for mining industry use through collaborative work at several mine sites. The JTA process involves three activities: (1) planning, (2) a 1- to 3-day workshop where the JTA is developed using facilitated work with subject-matter experts, and (3) followup. Guidelines and considerations for each of these activities are included. Results indicate that the JTA process has been well received and valued by mining industry participants. It blends aspects of health and safety, production, maintenance, and crew coordination.

Jan 8, 2006

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By A. C. Fieldner

This report, the third of a series of annual reports of research and technologic work on coal by the Technologic Branch to be released in this form, covers the fiscal year July 1, 1937, to June 30, 1938. Ever-increasing demands for information on the chemical and physical properties of coals, their proper classification rind adaptability for various uses, their economic evaluation in the complex relationships between the costs of production, distribution, and selling, and their beneficiation and amenability to conversion to more valuable and. new products of commerce have necessitated an appropriate and flexible program. To most these requirements, initiation of new projects and new physical facilities has been made.

Jan 1, 1939

By A. G. Mayton

Vehicle vibration exposure has been linked to chronic back pain and low back symptoms among agricultural tractor drivers. The objectives of this study by the National Institute for Occupational Safety and Health (NIOSH) were to assess driver whole body vibration (WBV) exposures and recommend interventions to reduce the risk of back related injuries, particularly relative to vehicle jarring/jolting (the transient mechanical shock components of WBV). The methodology included collecting, from two independent samples, ?eld data and health and work history data of farm equipment operators. Data were collected during mowing, raking, baling, chiseling, tilling, and road travel for different model tractors. Spraying using a sprayer and shrub removal with a skid steer loader were also included. Based on ISO 2631 (1985), the American Conference of Governmental Industrial Hygienists, threshold limit values, presents 0.5 m/s2 as the action level recommended by the Commission of European Communities for overall weighted total RMS acceleration (vector sum for axes x, y, and z) [ACGIH, 2006. Threshold limit values and biological exposure indices. Cincinnati, OH]. WBV measured at the operator/seat interface exceeded this action level. The roughest rides and highest vector sum accelerations occurred with small utility tractor mowers (3.3 and 2.8 m/s2) and a skid steer loader (1.7 m/s2). Major ?ndings from health and work history data showed 96% of participants reported having to bend or twist their necks, although 24% reported neck symptoms. Sixty four percent of participating operators reported experiencing back symptoms (e.g., pain, aching, stiffness, etc.). Recommendations included: specifying a seat that ??better?? isolates operators from jars/jolts with new tractor purchases; maintaining the seat/seat suspension and replacing worn or damaged cushions with NIOSH tested viscoelastic foam padding; using larger diameter tires with radial ply instead of bias ply construction, particularly on small utility tractor mowers, to aid in attenuating ride ??roughness??; using a swivel seat to reduce the stress on the neck from bending or twisting; and improving efforts to educate owner/operators of the adverse effects of WBV exposures. Since the data presented in this paper were collected from two independent samples, the authors were unable to draw any correlations or etiological inferences from the study. However, results were compared and contrasted with other studies which included similar vibration measurements in agriculture.

Jan 1, 2008

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By D. Harrington

Coal mines and mining-, as well as metal and nonmetallic mines and min¬ing, are not inherently unsafe, although mining people think they are and would like to have everyone else think so. It is now being demonstrated that mines can be operated with essentially as much safety as any other major industrial enterprise; but most mining people, including workers as well as officials, have been slow to realize or admit this. In the past, and with most people even at present, the idea has prevailed that it is utterly impossible to operate a mine without accidents. Although, as in all other kinds of industrial activity, it is true that some injury is likely on occasion to occur to some workers and an extraordinary accident may occur to one or more persons under exceptional conditions, mines can be operated with few if any accidents if a reasonable amount of the right kind of precautionary effort is exerted and kept in effect.

Jan 1, 1934

By M. Didyk

In this report, the application of the PHU/MVS program is demonstrated through the use of a simple but realistic mine ventilation program. The report details, the problem description, the input data required and the various output features of the simulator. The PSU/MVS program is written in Fortran IV for use with IBM 370/168 computers. A version of the program that can be used in CDC computers is also available. A ventilation network consisting of 531 branches, 300 nodes and 5 fans took 48 seconds for solution on The Pennsylvania State University's IBM 370/168 computer. Appendix I of this report is the User?s Manual for the program. Appendices II and III contain the input data listing, and selected output listing for; the application. Appendix IV provides tables for leakage, friction factors and shape factors.

Jan 1, 1977

By C. V. Brennan

This paper, describing the various mining methods and practices at Britannia mines, Britannia Beach, British Columbia, is one of a series covering mining practices, methods, and costs in the mining districts of the United States and Canada. The Britannia property has been operated continuously for 30 years, and in that time many diverse methods have been used in exploiting the various types of orebodies worked. Under normal conditions mining methods include surface gloryholes, shrinkage stoping, shrinkage with powder drifts for primary breaking, horizontal cut-and-fill, horizontal and inclined square-setting, and timbered and open rills, the three latter systems being combined with close filling. The Britannia method of mining, a large-scale retreating shrinkage system usually combined with powder drifts for primary breaking, has been developed and applied here very successfully. Each block of ground as developed is studied as a separate problem, and the mining method, or combination of methods best adapted to the work in hand is applied thereto. Operating at, capacity, the series of mines produces 7,000 tons of ore per day.

Jan 1, 1935

By D. Harrington

Every few weeks United States newspapers of 25 or 30 years age ran scare-heads telling of some mine disaster, which was a first-page attraction for a day or two and then was forgotton until another disaster occurred a few weeks later. Interspersed with these disasters were the so-called sniping mine accidents, causing the death of one or two mine workers. The summation of all types of mine fatalities usually exceeded 3,000 a year. In the period 1906-10, inclusive, there wore 84 major explosion disasters (or about 17 per year) in united States coal mines; the fatalities resulting from those disasters numbered 2,388 for the 5-year period. These frightful catastrophies helped to cause the total number of fatalities in our coal mines for the 5 years (including the fatalities from major explosions) to reach the enormous total of 13,288, an average of 2,658 per year. In addition, some hundreds of other typos of mining accidents swelled the annual fatality list to upwards of 3,000. This admittedly deplorable condition created so much Nation-wide comment that Congress was impressed with the necessity of having something done by the Federal Government with a view to trying to halt at least sonic of the excessive loss of life in our mines; in consequence, the Bureau of Mines was created and began to function in July 1910.

Jan 1, 1935

By Donald W. Mitchell, John Nagy, Edwin M. Murphy

"Investigations in the Federal Bureau of Mines Experimental coal mine near Pittsburgh, Pa., have shown that high-expansion foam containing at least 0.2 ounce of water per cubic foot of volume is effective in controlling exper-imental underground coal, oil, or wood fires. Some of the fires were extinguished, but more of the coal and wood fires were brought under enough control to permit direct attack with water or other extinguishing agent or loading the hot material into cars. The largest controlled experimental fire, which burned about 5 hours before attack, was in a coalbed 5 feet wide, 10 inches thick, and 100 feet long. The greatest distance foam was transported to control a fire was 1,010 feet.An incipient fire should be attacked promptly with water, rock dust, or other approved and readily available extinguishing agents. Where heat, roof falls, and smoke prevent direct approach, the more involved procedure of using foam may be advantageous. The effectiveness of the foam in controlling a deep coated fire of considerable extent H,vet to be proved by actual trials in aSome hydrogen, carbon monoxide, and methane gases are generated when a fire is attacked with foam. Calculations showed that in experimental fire tests an explosive mixture could form; however, this would occur only within a narrow range of combustible gas-air mixtures not likely to be found in practice. The principal explosion hazards are due to generation of gases by the foam, localized build-up of normally liberated methane, and volatiles liberated by the coal during heating. The quantity of combustible gases generated by the action of the foam on the fire is about the same as that when an equivalent amount of water is applied."

Mar 1, 1960

By R. V. Ramani

In this the available information friction factors and leakage report, on characteristics are reviewed and summarized. The use of Penn State Mine Ventilation Simulator (Volumes II and III of the Final Report) to analyze the sensitivity of the ventilation system to the changes in leakage and friction factors is discussed with examples. In simple ventilation systems, the results of changes in leakage and friction factors can be easily solved and explained by the laws of air-flow. In complex systems, with fixed quantity branches and multiple sections, the effect of changes in leakage and friction factors cannot be generalized. This study points out the importance of good input data for obtaining reliable information from computer analyses and demonstrates the application of simulators to analyze the effectiveness of ventilation systems. An extensive bibliography on friction factors, leakage characteristics and ventilation economics is included.

Jan 1, 1977

By C. Haycocks

The problems caused by interaction in multi-horizon mining are world wide and are not limited to the coal industry. These problems will continue to increase as mining of new seams multiplies and replaces production from mined out horizons. Interaction problems are particularly evident in the Appalachian coal fields which contain many mineable, contiguously placed coal seams. Selection of the mining sequence of these seams, historically and currently, is based primarily on considerations of seam ownership, availability, and economics. Experience has shown, however, that mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. This interaction effect is often detrimental to the recovery cost and safety of mining the subsequent seams. Designing to avoid or minimize interaction effects represents a major challenge to the modern coal mining industry and therefore is the focus of this research. In an effort to evaluate past interaction effects and provide guidelines for future mine design, interactive ground control problems were categorized into four areas. These are pillar load transfer, massive interseam shearing, subsidence and pressure arching effects. To facilitate research, each of these areas was studied separately although in reality these subdivisions are arbitrary and have considerable overlap.

Jan 1, 1983

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

By G. L. Bloomsburg

This report describes work which was done to apply an existing finite element computer program UNSAT2 to the unsteady, unsaturated flow of water through waste shale piles. The work was done in three phases: 1. Verification of program through comparison with existing data. 2. Verification of program through simulation of flow from field seepage ponds at Rifle, Colorado. Considerable laboratory work was done in this phase to obtain capillary pressure-saturation-relative permeability data and hydraulic conductivity values for retorted shale. 3. Application of program to flow due to natural rainfall in a section through the Piceance Basin in Colorado, and a typical waste shale pile.

Jan 1, 1978

By Robert C. Weisner

Current production costs and market conditions in the potash industry of the Carlsbad area were studied to determine the potential values of the potash mineral resource that would be lost or foregone if the Waste Isolation Pilot Plant (WIPP) facility is constructed on the proposed site in that area. The purpose of the WIPP project is to investigate the possibility of developing a nuclear waste disposal plant in the salt formations at the site. Analyses were made of all potash deposits determined to be in the site. Mining and processing under the most favorable recovery systems were considered. Value determinations were based upon estimated operating and capital costs of current mine-mill operations in the Carlsbad area. This study was made for the Energy Research and Development Administration (ERDA) by members of the Federal Bureau of Mines Minerals Availability System staff.

Jan 1, 1979

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By J. Kruttschnitt

This paper, describing the mining operations at Mount Isa Mines, is one of a series covering mining methods and costs being published by the United States Bureau of Mines. The Mount Isa property has been in operation since June 1931; during this period operations have changed from the production and treatment of carbonate ores to the mining, milling, and smelting of sulphide ores. This change involved revision of ore-extraction methods. Stoping methods have been designed to apply to parallel lodes ranging from 10 to over 100 feet in width and dipping at 50° to 60°. The hardness and strength of the ore and enclosing wall rocks, together with the strength and thickness of the country rock between lodes, have permitted the selection of a sublevel stoping method for mining the sulphide ores.

Jan 1, 1937

By C. Steve Albrecht

The primary objective of this study is to "evaluate the influences of different equipment systems on prime farmland subsoil compaction due to surface mining in the Midwest." The study is centered on four mine sites each utilizing a different combination of equipment for soil removal and replacement. Subsoil compaction is the primary focus of this research effort. Primarily owing to physical location, it is difficult to alleviate the increased compaction directly below the topsoil in reclaimed soils. Different equipment combinations cause varied effects when soils are replaced during surface mining activities. By collecting field data within a statistical framework, the effects of different equipment combinations on subsoil compaction can be evaluated and conclusions drawn. This research effort evaluates a comparison of natural and replaced soils by moist bulk density data. This comparison centers on changes in bulk density and texture to a depth of 48 inches. For each study site a complete case study is provided for use in data correlation and interpretation. Basis for this research effort centers on four (4) major experiment designs: o Comparison of soil bulk density values for three distinct equipment systems evaluated on the same general soil types (i.e. scrapers, bucket-wheel excavators and end-dump haulback); o Evaluation of the effects of soil replacement in repeated lifts using scrapers; o Presentation of bulk density values representing soil compaction for four (4) equipment systems (i.e. bucket-wheel excavators, draglines, scrapers and end-dump haul back) on four separate mine sites in the midwest; o A prediction analysis model is developed for subsoil bulk density following reclamation based on equipment characteristics and a statistical evaluation of texture. The soil data base of information includes data from the 1982 Bureau of Mines study entitled, "Impact of Surface Mining on Soil Compaction in the Midwest" as well as data from this research project. The final report is synthesized through an analysis of field data, statistical analysis and literature review. The final report focuses on the interpretation of results for practical application by government and industry.

Jan 1, 1984

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I -of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976