Search Documents

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By James Westfield

A brief résumé follows of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code fur Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous -coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reportin; to the Coal Mines Administrator any violations of the Federal Minis Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1960

By W. W. Odell

The results of the 1921 cooperative experiments conducted by the U. S. Bureau of Mines and the University of North Dakota at the University mining substation plent at Hebron , North Dakota , pointed clearly to certain definite dep ficiencies in the schemes hitherto developed for benefiting and utilizing lignite . First The apparatus used in the carbonizing process or used to produce carbonized lignite suitable for briquetting is too costly , that is , the cost per ton day of residue made is too high . Second - The depreciation of the carbonizing appara tus is too high . Third The carbonizing apparatus can not be operated intermittently without seriously damaging it and impairing its efficiency of performance . Fourth Too little attention has been given to the possibility of using at least a certain percentage of the carbonized lignite directly in suitable stoves and furnaces without briquetting or other treatment . Accordingly , consideration was given to the design of an oven that could be built at a mine without the importation of highly skilled and specially trained construction men , erected at a low first cost , readily kept in a state of repair , operated at a rela tively high capacity and put into operation or shut down at will without seriously damaging the brickwork . The need of such an oven was appreciated also by the University of North Dakota and a cooperative agreement was made to build and operate such an oven during the summer of 1921.

Feb 1, 1923

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concentration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidation practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concen¬tration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidaticn practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Leonard Obert

THIS REPORT presents methods and principles useful in designing underground mine openings and pillars in competent rock formations. Two types of formations are considered: (1) Massive formations, in which openings are generally mined with an arched roof, and (2) bedded formations, in which openings are generally mined with a flat roof. Design principles for openings and pillars in massive formations are obtained by considering the maximum tangential stresses developed around single and multiple openings for stress fields of various types. Design principles for openings and pillars in bedded formations are obtained by considering the average stress in pillars and the maximum stresses in roof layers. Experimental procedures for making stress, strain, and in situ physical-property measurements in underground mines to check design calculations are outlined and the results discussed.

Jan 1, 1960

By D. E. FOCG, A. E. Wells

When the United States entered the World War governmental agencies found little definite knowledge available as to the exact capacity of each sulphuric acid plant in the United States to manufacture acid under the stress of a great emergency. It is true that on account of the demand for acid for the manufacture of munitions for the Allies, prior to the entrance of this country into the war, most of the acid plants near industrial centers in the Eastern and Northern States were running at or nearly their maximum capacity, but, . for various reasons, many plants in these States and plants in other districts were not. For a number of years statistics as to the production of acid by the plants of the country were compiled by the United States Geological Survey, but obviously such figures did not give information as to the maximum capacities that might be available for meeting the he.a vy war ·requirements, or as to the steps that would have to be taken to bt-ing these capacities into use. During the summer and early fall of 1917 various attempts were made to obtain the desired information, but no satisfactory or complete data were obtained. Late in 1917, under the authority granted to the Bureau of Mines by the explosives act, the Director of the Bureau of Mines directed A. E. Wells, metallurgist of the bureau, to uiake a complete survey of the situation. Mr. Wells personally conferred with officials of the acid companies and visited most of the acid plants in the North that are east of the Mississippi River. The information obtained through this personal survey, together with that obtained through the ready cooperation of the subcommittee on ncids, and the subcommittee on fertilizers of the Committee on Chemicals of the Council of National Defense, enabled the preparation of a report containing the desired data concerning the sulphuric acid industry. This report was made immediately available to the War Industries Board and to those offices in the War and Navy Depart- ments that were most directly concerned in planning the explosives program and in obtaining the necessary supplies to produce the explosives. Beginning with this survey and report, the sulphuric acid section of the war minerals investigations of the Bureau of Mines took an active part in all matters pertaining to the sulphuric acid industry during the remainder of the war. Mr. Wells, the chief of the section, was appointed an associate chief of the sulphur, pyrite, and sulphuric acid sections of the War Industries Board. .Also, by this direct contact with the War Industries Board, the data obtained by Messrs. R. R. Hornor, H. A. Buehler, a.nd 0. Lindstrom, who were in charge, for the bureau, of the investigations concerning the supplies of pyrite and sulphur, were constantly made available to all interested Government agencies. D. E. Fogg, of New York City, was appointed chemical engineer to the sulphuric acid section to make special investigations relating to the acid industry, especially the possible utilization, in an emergency, of those sources of raw material.not then being used. Mr. E. E. Corbett, of Brooklyn, N. Y., was appointed chemical engineer to make investigations concerned primarily ,vith the conservation of acid. Direct and intimate contact with the industry was had through the close cooperation with the committee on acids of the Chemical Alliance, this committee during the greater part of 1918 occupying rooms with the acid section of the bureau. With the ending of the war and the close o:f the active work of the acid section of the bureau, the suggestion was made by many interested parties that a bulletin be prepared giving some qf the fun. damental and most important facts regarding the sulphuric acid industry, including a discussion of the technical :features of the manufacture of acid. During the war the bureau received -a vast number of inquiries in regard to various phases of the industry, a.nd this fact also made such a bulletin seem desirable. Therefore, the present bulletin was prepared to cover the main facts in regard to the industry in this country, including a discussion of the supplies of sulphur-bearing raw materials, the situation of the acid plants, the principal points in regard to manufacturing processes, and the uses of the acid. No attempt has been ma.de to discuss at length the manufacturing processes, as details differ more or less at the different plants and in general are carefully guarded by the acid ·companies. A great deal of the data given in this bulletin may be found in various pub]ications, but this is the first publication in which such data have been assembled and made readily available. Most of the data were obtained directly from observation and from cooperating acid companies or from individuals who had been or are now engaged in acid manufacturing and were liberal and generous in making their information available for publication. Care has been exercised to publish no data that were obtained as confidential by the bureau's representatives. The average acid manufacturer may be already more or less acquainted with most of the information presented in this bulletin, yet it is believed that the bulletin will be of value to those who wish to obtain a. general review of the present condition, both the economic and technical, of the sulphuric acid industry in the United States.

Jan 1, 1920

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By BUREAU OF MINES

TABLE OF CONTENTS

Sep 1, 1932

By R. K. Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed which allow the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

By K. C. McMahon

This report is the result of the engineering efforts performed by the Mining Equipment Operations of FMC to develop methods of automating a continuous miner. This work was done as part of modification number three of the contract for the development of a miner/bolter system. As the demand for energy places an ever-increasing pressure on the coal mining industry to produce more coal, methods for underground mining which will increase productivity with a con-current increase in safety are being actively sought. Removing the machine operator from his station on the continuous miner and placing him at a safer location behind the machine while retaining his control functions via an umbilical cable or a radio link was an important first step. However, the problems of poor visibility, no control "feel", and the judgmental problems of controlling the sump distance and the shear limits have not been conducive to the productivity increase that is desired.

Jan 1, 1975

By Frederick Bloetscher

An improved parachute-type stopping for changing the course of mine ventilation air during mine emergencies has been developed by Goodyear Aerospace Corporation for The Bureau of Mines. The stopping can be quickly deployed by one man from a single attachment point and provides excellent stopping performance with the flow in the design direction. Adding pin and foam attachments between its skirt and the passage-way surfaces improves its performance with flow in the design direction and maintains the stopping with zero or reverse air flows. Stopping performance results for a range of airway sizes including 7.5 X 10 ft simulated airway with pressure differentials of up to 3.0 inches of water are presented. Predicted performance values for this stopping design for larger passageways are also presented.

Jan 1, 1977

By J. Bongarra

This report describes the development of the instructional design and content of a training program for shaft construction miners and supervisors. The recommended training approach is based on the results of a needs, task, and competency analysis of the jobs performed by conventional shaft sinking and raise drill personnel. Learning objectives were derived from the task analysis and the appropriate training delivery system was chosen using a selection technique which employed learning algorithms. The training described is aimed at improving the safety and efficiency of constructing shafts by new hire and experienced miners and supervisors. A self-paced, self-teaching, modular approach to training, using criterion-referenced tests was proposed. Recommendation was made to divide the training into three parts: Orientation and Safety; Task Instruction; and Practical Exercise. Training requirements for conventional shaft sinking and raise drilling were described. Training program content was detailed in the form of module and lesson design approaches. In addition, the report recommends a method for developing, implementing and validating the training program. The authors conclude that such an implementation would meet the major objectives of improving the safety and efficiency of shaft construction work operations.

Jan 1, 1979

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

By R. S. Dean

A large metallurgical experiment station at Salt Lake City to house the works of the Bureau of Mines in the intermountain area properly has long been projected. It finally became possible when a Public Works Allotment of $300,000 was set aside for building and equipment. With the new building assured, the Bureau of Mines decided to move the headquarters of its Metallurgical Division from Washington, D. C., to Salt Lake City, Utah. It was felt that this move would simplify they administrative work of the chief engineer of the division, as all stations devoted primarily to metallurgical work are west of the Mississippi. These include Rolla, Mo.; Minneapolis, Minn.; Pullman, Wash.; Reno, Nev.; Berkeley, Calif.; Boulder City, Nev.; and Tucson, Ariz. In addition to these stations will groups, of investigators working on metallurgical problem, are maintained at Pittsburgh, Pa., and College Park, Md. Salt Like City was clearly a more central point for the direction of this scattered work than Washington, D. C. The building (fig. 1, A and B) was designed from general plans worked out by the authors of this paper. Contraction was begun in March of 1939, and by the end of the year the Metallurgical Division had moved, into its now quarters.

Jan 1, 1940

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States from 1961 through 1967. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included.

Jan 1, 1969

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986

By S. W. Zoldok

"ERRATUMFor paragraph 1, page 1, read the following:The Cle Elum nickeliferous iron deposits occur on an unconformable contact between the serpentine and overlying Swauk sandstone formation and extend about 2 miles along the Cle Elum River in Kittitas County, Wash.The linear extent of the deposits and their proximity to a large source of,electric power and coal supply indicated that a development program was in order to determine the probable grade, extent of the ore bodies, and a suitable metallurgical process for recovering the iron, nickel, and chromium from the ore.The northern portion of the serpentine formation was investigated by the Bureau of Mines from August to December 1943 and from August to October 1944. The investigation consisted of road building, diamond drilling, sampling, and metallurgical tests.The Geological Survey assisted with logging of cores and made geologic and topographic maps."

Feb 1, 1948

By S. J. Hemberger, F. W. Lee

"This project constitutes the results of a geophysical field investigation undertaken in the mining areas in the vicinity of Marion, Crittenden County, Kentucky.Results were obtained at well-known mines being worked for fluorspar. Of special interest was the determination of mineral trends at such mines, particularly in relation to the fault patterns, because of ore in them.This work also constitutes a comparison between the field information that can be obtained by purely geological means and the additional information obtained by applying geophysical surveys to the same areas.As the mineralization in this area is controlled almost surely by the faults therein, the great importance of locating faults cannot be over emphasized. Accordingly, there has been incorporated herein the analyses as well as the application of electrical resistivity methods for fault determinations.In the western part of Kentucky, particularly in that area designated as the Cave-In-Rock quadrangle by the United States Geological Survey, is located the center of the fluorspar mining district of Kentucky. From the mining as well as commercial viewpoint, this area is of considerable interest and importance. It has been described by Currier4/ as a large structural dome that collapsed, through faulting, into a mosaic composed of a main fault pattern that has a strike to the northeast in sedimentary formations. Accompanying this main fault pattern are a large number of irregular faults. This fault complex is also traversed by a dike pattern that has a regional strike for this region focusing a northwesterly direction. The faulting occurred before the dike intrusions, the latter being composed largely of peridotite rocks. According to Reed,5/ most of the metallic mineralization, composed chiefly of galena and sphalerite, occurs at or near the Intersection of the dikes with the faults, indicating a possible igneous origin of the ore deposits. Reed adds that the fluorspar generally does not follow this rule but may also be found in other portions of the faulted zone not directly related to dike intrusions. The area may be considered of equal interest in the occurrence of lead and zinc and in the occurrence of fluorspar controlled by the faults. Hatmaker and Davis6/ give detailed information concerning the form of the ore bodies and economic factors that control ore production in this area; they also suggest the application of geophysical methods in this territory. Ulrich and Smith7/ also discuss geological details in this area. This area is therefore of interest, whether examined from a large structural point of view or from a very detailed angle. The former will assist in determining the origin of the mineralization and its economic possibilities, whereas the latter will give details concerning fault locations and their geologically and geophysically controlling features. This work was undertaken as a pilot investigation relating to the study of the location of fault occurrences, in which it was attempted to determine the location of faults as well as the fault patterns in certain isolated areas. No effort was made to identify the mineralization from the gouge material in the faulted zones; this problem was left for subsequent investigations."

Jun 1, 1946

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan's raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan's dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983