Search Documents

By K. Richardson

Although the De Beers group has a long history of placer mining on land, the group only became actively involved in deep water marine diamond exploration and mining in1983 with the formation of De Beers Marine. Full-scale commercial mining commenced around 1991. Since then, the group marine mining capability has grown into a formidable fleet of 8 large deep water (>70 m) mining vessels, as well as other special purpose geo-survey platforms. Marine diamond production by the group is expected to be just short of 1 million carats in 2006. DeBeers operates across the entire value-chain spectrum from geology and geo-survey, through sampling to mining, and finally ore processing into high value concentrate. Supporting these operations involves significant service activities such as maintenance, security, logistics and environmental management. Specific challenges exist in terms of developing or acquiring appropriate technology for marine mining. These challenges have resulted in DeBeers operating extensive in-house R&D and projects departments, as well as drawing extensively from technology partners. An array of computational and test facilities are also available to support R&D and projects activities. Hydro transport in various guises is key to the current approaches to marine mining and ore processing. Use is made of airlift and centrifugal pumping for hydraulic hoisting of very coarse gravel, while splitters, launders, dewatering, elutriators, jet-pumps, centrifugal pumps, dense medium circuits, pipeline systems, and instrumentation for coarse abrasive particles are used extensively in the ore processing plant.

Jan 1, 2007

By D. F. Caicedo, I. A. Brum, L. A. Betancourt

Ferricyanide ()()*is one of the most stable cyanometallic complexes present in the gold mining effluents. This cyanocomplex is hard to degrade by natural attenuation and generates a negative impact on aquatic environments. Although free cyanide (CN-) can be obtained by acidifying the solution, the CN- is lethal for all forms of life. The oxidation of ()()* in a typical photocatalitic system was evaluated with the addition of H2O2. To verify the degradation, chemical parameters, such as free cyanide, the formation of ammonia, nitrate, and total iron were analysed at the end of the process. The degradations obtained were up to 70% in a heterogeneous photocatalysis system with TiO2, and a low rate of dissociation was observed by photolysis. The best result was achieved with the H2O2 and TiO2 photocatalytic system, and the stoichiometric concentration was about 2.5 times less than the peroxide used in the real gold mining industry, reaching 83% degradation. The photocatalytic process obtained less toxic byproducts than the original synthetic ferricyanide used as mining wastewater. Keywords: Cyanide, heterogeneous photocatalysis, titanium dioxide, UV radiation, gold wastewater

Jan 1, 2020

Most processing plants use automatic samplers to extract ore aliquots along a producing shift. These aliquots are combined into a sample normally sent to lab analysis. The sampler used in the extraction of an aliquot from a continuous flow of ore, i.e. a belt conveyor is required to be both precise and accurate. Surprisingly, not all commercial automatic samplers exhibit these two mandatory properties. Consequently, it is recommended the development of a procedure able to check sample assays reproducibility obtained using a given sampling protocol. This paper uses the Gy’s sampling theory to evaluate coal quality control practices at a washing plant using an automatic sampler extracting coal increments from the ROM feeding belt conveyor. Gy’s theory provides the means to establish the precision limits for a given sampling protocol. Various ore properties are required to be determined in combination with sample mass and mass of the lot sampled. All this information leads to the definition of the precision limit. The precision limit obtained was checked via an experiment mimicking what happens in situations where both miner and consumer use the same and appropriate sampling practices. The experiment demonstrates that sampling theory precision limits were valid if unbiased samplers are used by both parties, i.e. miner and consumer. Keywords: sampling, quality control, coal

Jan 1, 2003

By A. V. Wilke

The metallurgical balance is a tool usually applied in the mining industry. The final result is used for different objectives. All the existing software for the calculation of the metallurgical balance fits the numbers in such way that a logical correspondence between the input and output materials exist. Nevertheless, the accuracy of the metallurgical balance strongly depends on the quality of the input data. Division El Teniente of Codelco Chile has been optimizing the metallurgical balance system the last 14 years. As well, it has participated in the development of corporate norms to optimize the operations of sampling and weighting systems. As a consequence, the precision and the accuracy of the metallurgical balance have been improved in a significant way. Also the understanding of process variability was enhanced. The improvements have allowed Codelco to discover and minimize hidden losses and to better support top management decisions. The present paper describes the main aspect of the continuous improvement process.

Jan 1, 2009

By C. Chongo, F. X. Paquot, C. Ngulube

"Over the last six years, the Kansanshi copper/gold mine has continued to process significant quantities of complex transitional mixed ores. The effect of the complex mineralogy on the flotation performance is depicted. Initially, ore treated came predominantly from accumulated stockpiles. In the ensuing years, ore treated shifted to primarily freshly mined ore that generally showed less tarnish with better float kinetics but with the downside of producing lower concentrate grades. A number of changes were made to improve the efficiency of the roughing circuit and quality of concentrate produced. These changes were as a result of initial mineralogical studies and laboratory float test work done and discussed at length in a previous paper. Salient among the adopted recommendations from previous work were increasing circuit capacity and modifying configuration to increase the residence time and the number of sulphidisation stages. These modifications were completed and commissioned in 2011. This, however, resulted in significantly low rougher concentrate grades and subsequently below-specification final concentrate product. This was primarily due to higher mass pulls resulting from the extended rougher bank with multiple concentrate discharge streams. This necessitated the need for an enlarged cleaning capability to offset this. The extra cleaning capacity came on-stream in 2014. Of note was the development of a recovery model, based on the strong correlation between the total copper and acid-soluble copper ratio, as a tool for monitoring plant performance. INTRODUCTION The Kansanshi mine, the largest copper mine in Africa, is 80% owned by Kansanshi Mining PLC, a First Quantum subsidiary. The remaining 20% is owned by the state through the parastatal ZCCM. The mine is located approximately 10 km north of the town of Solwezi and 180 km to the northwest of the Copperbelt town of Chingola. The mine has been in commercial operation since 2005. Prior to June 2009, Kansanshi mine treated only two ore types: oxide and sulphide. All transitional ores mined during the period leading up to 2009 were stockpiled. The treatment of the minerologically complex, transitional ores through a third train commenced in June 2009 but with numerous metallurgical challenges. This transitional ore (called mixed ores) could not be previously treated economically due to high gangue acid consumption (GAC) minerals association (making it unsuitable for the oxide float–leach circuit) and poor flotation response ruling out the conventional sulphide float circuit. The new novel circuit involved a conventional sulphide pre-float followed by flotation involving staged controlled potential sulphidisation (CPS)."

Jan 1, 2015

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

By Gerhard Nel, Huziel Masiiwa, Marthie Kotze, René du Preez, Simon Donegan

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology, to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when it is attempted to maximise the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory test work was conducted on the raffinate of the cobalt solvent extraction circuit to optimise the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimised in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory test work results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

By B. Dias, P. C. Schutte

Work-related musculoskeletal disorders (WMSDs) affect the wellbeing of workers and result in poor quality work, lower work performance and decreased motivation. In contrast to ‘occupational’ diseases where there is a direct cause-and-effect relationship between hazard and disease (e.g., asbestos and asbestosis, lead and lead poisoning), ‘work-related’ diseases are multifactorial, where the work environment and the type of work that is performed contribute significantly to musculoskeletal disorders. WMSD is the term used to describe disorders and diseases of the musculoskeletal system (i.e. muscles, joints, ligaments, tendons and nerves). WMSDs are by definition a work-related phenomenon. The literature shows inarguably that certain jobs and certain work-related factors are associated with a significant risk of contracting a WMSD. It is assumed that repeated movements and postures, static work, continuous loading of the tissue structures or lack of recovery time, trigger or cause a pathological process that then manifests itself as a WMSD. This paper looks at the prevalence of the WMSD condition at three mines in South Africa: a coal, a gold and a platinum mine. Predisposing factors that include work factors, presentation of symptoms and psychological factors will be discussed in the paper.

Jan 1, 2003

By S. Adams, J. R. C. von Holdt, J. L. Broadhurst

Fugitive dust from mineral extraction and processing activities can significantly influence air quality, the environment, and the health and quality of life of workers and surrounding communities. Poor engagement and communication between experts and lay persons, disciplinary silos and polarised viewpoints have made it difficult to develop a holistic understanding of the complex health issues associated with environmental emissions of mine dusts, and consequently to design meaningful and integrated approaches to address such issues. The collaborative Global Challenges Research Fund (GCRF) Mine Dust and Health Network, hosted by Minerals to Metals at the University of Cape Town, serves as a collaborative think-tank to inform research directions within and across disciplines, government policy and regulations, health monitoring programmes at public clinics, industry best practice, community healthcare and impact prevention programmes. It focuses initially on the southern African region, but with the intention to expand to mining-intensive developing countries within the rest of Africa, South America and Asia. This paper outlines the approach and activities of this global transdisciplinary and intersectoral network and presents some of the key outputs and achievements to date. Keywords: Mine dust, Global Challenges Research Fund Mine Dust and Health Network

Jan 1, 2020

By P. J. D. Lloyd, Jill Urban, M. R. Urban

The adsorption of gold from cyanide solutions onto constituents of the reef, and its role in reducing the efficiency of the gold-recovery process by M. R. URBAN. M.Sc. (Chem. Eng.) Rand (Visitor). JILL URBAN. B.Sc. (Chem. Eng.) Rand (Visitor) and P. J. D. LLOYD. Ph.D. (Cape Town) (Fellow) Evidence for the adsorption or re-precipitation of gold from cyanide solutions onto gangue minerals of the Witwatersrand reefs has been gathered over a number of years by various investigators. The evidence from tests using radioactive tracers is conclusive and indicates thlt adsorption contributes about 0,1 g/t to the total gold loss from conventional reduction works. The loss is a function of the alkalinity and cyanide concentration of the solution, and it appears to be affected by the extent of time between milling and cyanidation. The heavy minerals appear to be the strongest adsorbers, and the clay minerals somewhat less strong adsorbers. A sensitive qualitative test based on thin-layer chromatography permits the extent of adsorption and desorption to be readily determined.

By R. Van Deventer

The BIOX® process was developed for the biological pre-treatment of refractory gold ores and concentrates ahead of conventional cyanide leach gold recovery. Rights to the process are currently with BIOMIN Technologies SA, a subsidiary of Gold Fields Limited. There are currently eight operating installations worldwide employing the process on a commercial scale. EKATO is a company specializing in developing new or optimizing existing mixing applications. EKATO has acquired a vast amount of expertise in agitation over its 75 year history. In a joint research project the reactors of the BIOX® process were characterized from the aspect of their mixing performance. BIOMIN is constantly testing new mixing solutions and reviewing potential vendors to increase the efficiency of the BIOX® process. EKATO?s intention was to qualify as an approved vendor for supplying agitation equipment to the BIOX® process. A two step approach was planned: In phase one of the project EKATO would develop an alternative agitation solution to the established option, exhibiting at least similar performance levels. In phase two potential possibilities to improve the overall design would be developed. This paper focuses on phase one and addresses the systematic approach applied by EKATO in characterizing the mixing processes. Mixing tasks were assessed individually applying basic theory and scale-up and -down rules to the individual tasks. Testing with model systems was done at the EKATO technology center in Schopfheim, Germany, on scales of 50 liters and 1 m³. The results showed that the ISOJET-B impeller design showed promising performance under BIOX® reactor conditions. Scale-up with the ISOJET-B was done in order to apply it in the 21 m³ live volume test reactor at Fairview mine in South Africa. At Fairview tests were performed using model systems and eventually under real plant conditions with BIOX® slurries. The results were a success and confirmed that the scale-up factors determined during the testing at EKATO?s technology center could be substantiated in the ?model scale? 25 m³ reactor. Testing under the actual process conditions showed that all design parameters were within the desired range to be considered an excellent leaching performance. This successful joint development shows the importance of a close cooperation of technology licensors or end-users and equipment suppliers. It is vital for understanding all factors influencing the mixing performance of processes. Exercises such as this will provide equipment suppliers and plant operators more confidence in managing further scale ups at ever larger engineered plants.

Jan 1, 2009

By G. van der Westhuizen, F. E. du Plessis

Ticor South Africa operates a dry mill at the town of Empangeni in the province of KwaZulu-Natal on the east coast of South Africa. The dry mill processes a non-magnetic mineral stream constituting rutile, leucoxene and zircon as major minerals, and minor quantities of ilmenite and other non-valuable minerals. For plant control and optimization, continuous ‘real time’ information about the mineral and chemical compositions in various plant streams is required. The current practice is to take samples at regular intervals and submit them for mineralogical(grain counting) and chemical analyses. However, these methods are time consuming, and in the case of manual grain counting, tedious and operator dependent. Until now an on-line or real-time instant mineral quantification system, which will be of great value in a plant operations environment, has not been available. Blue Cube Systems has developed a mineral quantification system using spectral mineral analysis. It measures and quantifies the composition of mineral samples instantly, providing consistent data in real time. A series of process stream samples from the dry mill mentioned above were used to evaluate the Blue Cube Systems instant mineral quantifier. This article will •describe the procedure of setting up and evaluating the Blue Cube Instant MineralQuantifier equipment •present its results, and •discuss the intended applications.

Jan 1, 2003

By T. P. Letsebe, L. Magwaza, T. A. Sethu, S. M. Rupprecht

"The authors were tasked with introducing safe and efficient drilling and blasting practices to a small artisanal mine located in the Eastern Province of Rwanda. The current mining methods employed at the mine are inefficient as rockbreaking is conducted utilizing hammer and chisel, or by drilling and blasting with no understanding of the rockbreaking process. The paper discusses the drill and blast cycle, as well as the associated activities necessary to support the mining cycle. The challenges and critical aspects in implementing drill and blast activities are discussed, as well as some of the technical aspects, i.e.drilling pattern, initiation and timing of the blast, and handling of misfires. Ancillary issues such as ventilation, training, communication, effective planning, logistics, and human relations are also examined. IntroductionRockbreaking accounts for 60% of the direct mining costs in small-scale mining. When drilling and blasting practices are poorly implemented the process becomes inefficient and dangerous. The introduction of a proven drill and blast system to artisanal mining offers a number of challenges, with safety being considered the backbone of any sustainable operation and a standard that cannot be compromised.The paper is based on a project at an artisanal cassiterite (tin) mining operation in a small village in the Kayonza District in the Eastern Province of Rwanda. A drill and blast programme utilizing industry best practice was introduced at an underground development end; a raise developed at an inclination of 23 degrees. The underground working is accessed via a 17 degree incline shaft with an operating length of 105 m and serviced by a single drum winder. The winder operates at a speed of about 3.5 m/min hoisting two 1 t wagons from the bottom of the incline to surface for tipping (Figure 1)."

Jan 1, 2017

By T. S. Seleka

Laser surface melting has been conducted on a 304 stainless steel (SS) with the aim of enhancing pitting corrosion resistance of the material. This process involves rapid melting of the material?s surface followed by rapid solidification to refine the microstructure. This includes the dissolution of inclusions such as MnS, FeS, CrxCy, and other minor constituents. The microstructures as a result of laser treatment were observed by means of optical microscope and also confirmed by the XRD. The glow discharge optical emission spectroscopy (GDOES) was utilized for chemical analysis. Changes in hardness were observed by using a Vickers microhardness tester. Pitting corrosion tests on laser treated and untreated samples were conducted according to ASTM G48-92 to evaluate mass loss and pitting morphology. Laser surface melting improved the pitting corrosion resistance of this material in a chloride-containing environment.

Jan 1, 2007

By C. Liu, G. Zhu, Y. Liao

"The effect of particle size on the flotation kinetics of a low-rank coal was compared using air bubbles and oily bubbles. Five kinetic models were applied to the data from the tests to derive the relationships between the flotation rate constant, the ultimate recovery, and the particle size fraction. The results show that oily bubble flotation (OBF) resulted in a lower ash content and higher combustible recovery than air bubble flotation (ABF), especially for the -125 ??m size fraction. It was found that the flotation of a low-rank coal in individual size fractions using air bubbles and oily bubbles can be best described by a first-order model with rectangular distribution of tendency to float and the classical first-order model respectively. OBF yielded higher ultimate combustible and ultimate ash recoveries. The flotation rate constants for OBF were higher in all the models except for the fully mixed reactor model. The ultimate recovery values and modified rate constants first increased and then decreased as the size fraction decreased. The trend of the flotation rate constants as a function of the size fraction was similar in all the models except for the fully mixed reactor model. IntroductionFroth flotation is a physical-chemical separation method that is widely used in coal beneficiation for the separation of fine coal particles from associated minerals in water slurries. Since the cumulative recovery of a component in the concentrate is proportional to flotation time, the flotation process can be considered as a time-rate recovery process (Emad, Mohammad, and Bahram, 2010). Therefore, the general mathematical flotation models that incorporate both a recovery and a rate function can describe flotation time recovery profiles.The kinetics of coal flotation, as a measure of coal recovery as a function of time, have been studied in detail by many researchers. Different kinetic models have been proposed and published in the literature. The order and the rate constant are strongly dependent on the flotation conditions, such as the particle size and size distribution, the bubble concentration, the reagent concentrations, and the operating parameters (Zhang et al., 2013). The particle size has been reported to affect the flotation kinetics to a great extent (Yoon, Luttrell, and Asmatulu, 2002; Ntengwe and Witika, 2011). Numerous researchers have studied the aspects of flotation kinetics while paying special attention to particle size (Meftuni and Ibrahim, 1997; Rubinstein and Samygin, 1998; Graeme, 2012). However, the effect of particle size on the flotation kinetics of a low-rank coal has been relatively little discussed."

Jan 1, 2017

By T. Field, N. D. Nxumalo

Since the discovery of gold on the Witwatersrand in 1886, mining has been at the centre of South Africa’s development. Although mining continues to contribute significantly to the country’s economy, it is a temporary land-use activity, and mine closure is inevitable. This paper reviews mine closure planning at Tshikondeni coal mine, which commenced in 2014 with the initiation of mine closure. The review presents the mine closure processes undertaken at the Tshikondeni coal mine as regulated by South Africa’s principal mining legislation, the Mineral and Petroleum Resources Development Act 28 of 2002, and other relevant regulatory frameworks. To compile this review: (1) A desktop study was conducted; (2) empirical data was collected through one-on-one interviews with research participants at Tshikondeni coal mine; and 3) physical observations were made of the rehabilitation at various mine operations within the Tshikondeni coal mine complex. Research participants consisted of mine officials from different departments, i.e., human resources, and environmental, social, and business strategy, who were directly involved with the Tshikondeni coal mine closure. A questionnaire with semi-structured questions was developed. It was utilised to acquire a better understanding of mine closure planning at Tshikondeni coal mine and identify mine closure processes that aim to achieve post-mining land uses and align with Tshikondeni coal mine’s post-closure strategy, namely the Tshikondeni Legacy Project, with a post-closure strategy that has the potential to transition a mining economy to an eco-tourism economy that can preserve livelihoods and selfreliant communities.

Dec 15, 2025

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, there by lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3Dmulti-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2006

By F. L. D. Cloete

The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performace was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp.

Jan 1, 1981

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019