Search Documents

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By J. P. Gous, M. Tangstad, J. D. Steenkamp

In April of 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. One of the areas excavated systematically was the furnace taphole. The aim was to obtain a refractory wear profile of the tap-hole area, together with affected hearth and sidewall refractory. Subsequently, thermodynamic modelling was applied to quantify the potential for chemical reaction between refractory and slag and refractory and metal in the tap-hole area.

Jan 1, 2014

By P. J. K Leeuw, E. Uludag, M. J. Nong

Efficient drill-and-blast performance is pivotal to the profitability of deep-level mines, where high operating costs and declining grades demand maximum throughput. This study investigated persistent fragmentation problems at a longhole stoping operation that suffered from simultaneous oversized rock blockages in 300 mm × 300 mm grizzlies and excessive fines. Fifty-one muckpile images from five blasted stopes were analysed with Split-Desktop. Although the overall F₈₀ was 287 mm, nominally suitable for the grizzly aperture, the Rosin- Rammler uniformity index of 0.80 revealed a highly inconsistent size distribution containing both boulders and fines. Existing drill patterns were then evaluated with the Aegis underground software, which showed negligible crack overlap at the toe owing to inadequate spacing and burden. Insufficient energy overlap between blastholes, particularly at the toe, was found to contribute to the coarse fragmentation, while excessive fines were attributed to the crushing and severely fractured zones of blastholes. Optimisation simulations demonstrated that an 89 mm blasthole diameter on a 2 m × 2 m pattern would overlap, aligning with Aegis requirements of balancing powder factor, break angle, and energy distribution. Implementing this revised pattern is expected to reduce secondary breaking, prevent ore-pass blockages, lower fines, and ultimately improve overall production efficiency. The methodology illustrates how integrated image analysis and modelling software can effectively diagnose and address fragmentation issues, particularly in underground longhole mining, where challenging blasting conditions require a balance between achieving optimal fragmentation and maintaining stope stability. This approach offers a cost-effective pathway to improving comminution performance in deeplevel mines.

Oct 2, 2025

By A. Modi, C. Li, R. Kabwit, W. Y. Xinchao, R. Joshi

The KIMIN copper project can treat 1.7 million dry t/a copper-cobalt ore. It has three mills in operation, two using conventional milling in water and the third in raffinate. We introduce the project process circuit and the capital and operating costs of using the raffinate process compared with conventional milling in water. There is a capital saving of approximately 11.5% for major equipment by removing the pre-leach thickener. In addition, it also achieves an annual operating cost saving of USD 2.1 million due to an increase in 49% of acidic raffinate recycled and reduction in lime consumption. The features of CITIC’s new duplex stainless-steel ball mill ,as the key equipment of the system, are also introduced

Jan 1, 2023

By C. R. Royal, B. E. Friedland

Energy & Densification Systems (EDS) has developed patented new technology crushing/milling equipment. The EDS Multishaft Mill is a compact vertical mill – utilising high-speed impacts to break down particles with large reduction ratios, low energy consumption and improved liberation. The milling action combines several processes to provide a multitude of output products to satisfy various specifications. Comminution often accounts for more than 60% of the total power consumption on a mine. Two of the key problems to be solved in comminution is to bring down the specific energy required to reduce particle sizes; and to improve liberation or improve the efficiency of the beneficiation and recovery of the required elements. The EDS Mill has shown extensive improvements in both these areas with energy efficiencies up to 75% better than conventional milling equipment and improving liberation beyond the standard beneficiation processes. Conventional comminution equipment requires massive, heavy parts to be moved or rotated, consuming a lot of energy in doing so and not inputting that energy into the breakage of particles. In the EDS Mill, ramping up the relatively small shafts to speed is all that is required. Once at speed, the momentum, together with the minimal amount of constant drive required, means that the energy can be transmitted directly and efficiently into breaking down the particles. The high-speed impacts allow for a shattering effect of the particles and this quickly generates a high ratio of fines. Furthermore, the single impact force breaks particles in a very different manner to conventional compressive force breakage. With compressive force breakage, the particle breaks from point to point. With high-speed impact force breakage, the force tends to migrate through the weakest areas of the particle, which tend to be the mineral boundaries. This, therefore, means that when the particles break, the various minerals are exposed and hence liberated. Keywords: Comminution, high-speed impact, liberation, energy efficiency, novel comminution

Jan 1, 2020

By N September, R Abate

Bateman Modular (previously Van Eck and Lurie) has been building and supplying the mining industry with modular DMS plants for the last 30 years. These DMS modules range in capacity from 1 tph to 200 tph. The most popular unit produced by Bateman Modular over the years has been the 50 tph module. Development In the last 7 years a need has arisen from the industry to provide Modular DMS plants that can treat higher tonnages (150 to 200 tph). The first DMS provided to the mining industry based on the modular concept was a 150 tph DMS Module to MIBA in the DRC. Since then Bateman Modular has provided some 14 Mega DMS modules over the last 7 years with the latest two orders from Debswana (Damtshaa double up project) and Namdeb. Ever since the first Mega Module was supplied Bateman Modular has been improving the Modules. Implementation The modules can be supplied in different configurations so as to improve the overall availability of the plant. Two off 150 tph DMS modules were supplied for a Transhex operation. This allowed the client to still operate one DMS module while maintenance is being performed on the other DMS module. The client also has the option of choosing a single module. Successes The following list of projects provides the base for the success of the Mega Modules.

Jan 1, 2006

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African discard coal fines and K₂CO₃ blends were heated in a laboratory-scale rotary kiln to produce ashes for H₂SO₄ leaching tests. The optimized H₂SO₄ leaching conditions of 6.12 mol.dm³ (M) H₂SO₄, solid to liquid ratios 1:5 and 1:10, and 80°C for 8 hours were used. K₂CO₃ was added to increase the dissolution efficiency of K. The objective was to determine if the Al present in metakaolinite (Al₂O₃.2SiO₂), the Al, K, and Ti in the alumino-silicate glasses, and the Ti in rutile (TiO₂) in the ashes could be selectively dissolved in H₂SO₄. XRF results show that the ashes formed at 700°C dissolved more efficiently (87% Al, 89% K and 23% Ti) compared to the ashes formed at 1050°C. This can be attributed to the presence of Al₂O₃.2SiO₂, K₂CO₃ melt, K₂CO₃ remnants, KAl(SO₄)₂, and K-aluminosilicate glass in these ashes. XRD results indicate that the ashes prepared at 1050°C contained anorthite (CaAl₂Si₂O₈), microcline (KAlSi₃O₈), pseudomullite (Al₂O₃.SiO₂), and silicon spinel (2Al₂O₃.3SiO₂), which are either insoluble or only sparingly soluble in H₂SO₄. These minerals resulted in the lower dissolution efficiencies of Al and K. Based on the high dissolution efficiencies of Al and K for the ashes produced at 700°C, coal fines blended with K₂CO₃ could possibly be utilized as feedstocks for the production of aluminium(III), potassium(I), and titanium(IV) and a sulphate-containing leach liquor. Furthermore, the environmental issues and costs associated with the handling and disposal of large volumes of coal fines will also be resolved.

Aug 2, 2022

By A. Pareek, V. S. Masampally, V. Runkana

Mineral processing plants, in general, consist of comminution and separation circuits. Rougher flotation is considered as the heart of the separation circuit with concentrate grade and mineral recovery being the key productivity and quality parameters that affect the downstream operations and profitability. Online prediction of these parameters can help improve process performance in real-time. Past efforts to predict flotation cell performance have focused on building physics-based or machinelearning (ML) based models. Although physics-based models are popular in process design applications, ML models are more appropriate for online monitoring, control and optimisation due to their lower computational requirements. Deep learning (DL) is gaining prominence nowadays for application in industrial operations where a large amount of data is available. We have developed a DL model based on long short-term memory (LSTM) neural networks to forecast the two key performance indicators (KPIs), namely, mineral recovery and concentrate grade in a mineral processing plant. Rougher feed characteristics such as mineral grade and particle size distribution, upstream measurable disturbances such as throughput of the comminution circuit and pulp density, and control variables such as aeration rate, pH, and collector addition rate are considered as explanatory variables to train the model. The model was tested with data from an industrial mineral processing plant. For real-time dynamic predictions, the trained model appropriately accounts for mismatch in measurement frequency of real-time process data and off-line laboratory analysis data. Such a time series model can be used as a state observer in model predictive control techniques for optimal control of unit operations in a mineral processing plant. Keywords: Mineral processing, flotation, time-series, dynamic modelling, deep learning

Jan 1, 2020

By K. Sasaki, S. Kuroiwa, H. Miki, Y. Aoki, T. Hirajima, Y. Orii, G. P. W. Suyantara

Selective flotation to separate copper minerals from, for example, Mo- and/or As-bearing minerals is a continuing problem because the selectivity of current systems is imperfect. Selective Cu-As flotation is currently difficult, and the most common Cu-Mo selective flotation method uses NaHS; this must be done in an enclosed system because, under acidic conditions, this method produces hydrogen sulfide. In this paper, some novel alternative flotation processes that use redox reactions are discussed; these methods have a much lower environmental impact. Oxidation and reduction reactions can be used to make copper minerals more hydrophilic and Mo-bearing minerals more hydrophobic. X-ray photoelectron spectroscopy (XPS) analyses indicated that the copper minerals became hydrophilic because hydrophilic iron precipitated and several hydroxides covered the copper minerals’ surfaces, whereas the molybdenum minerals remained hydrophobic because their sulfide surfaces were not covered. Flotation experiments on these minerals after redox treatments indicated that excellent separation of Cu-minerals from Mo-minerals can be achieved. Possible mechanisms for this separation were investigated using detailed surface analyses and thermodynamic calculations. The additives used to initiate the redox reactions are easy to handle and make these new flotation procedures better than current processes because the new methods do not emit effluent gas and because they are commercially viable. Keywords: Flotation; chalcopyrite; molybdenite; oxidation; reduction

Jan 1, 2020

By V. Jovicic, J. Likar

The knowledge of the geological sequence and hydrological conditions in the area of portals was the basis for the design of the entry of the highway into tunnel Trojane. Mudstone, claystone and sandstone dominate the rock layering, which is tectonically reworked and contains structural anomalies. The complexity of the sequence makes it impossible to survey all the relevant features along the full 3km length of the tunnel. Sudden and frequent transitions between litological sequences impose potential instabilities and make the excavation of the tunnel particularly difficult. The initial survey established the zones of potential failures. These were monitored using topographic survey and inclinometers with an aim to make further geotechnical analyses more reliable and adjusted to the ground conditions. The analyses of the wall construction and the results of the monitoring showed that the design of the retaining wall was adequate. La connaissance de la séquence géologique et des conditions hydrologiques dans l'aire des portails a été la base pour la planification de l'entrée de l'autoroute dans le tunnel Trojane. Le schiste, l'argilite et le grès dominent la couche rocheuse qui est tectoniquement transformée et contient les anomalies structurales. A cause de la complexité de la séquence, il est impossible de revoir toutes les particularités le long des 3 kilomètres de la toute longueur du tunnel. Les transitions soudaines et fréquentes entre les séquences lithologiques imposent l'instabilité potentielle et font l'excavation du tunnel particulièrement difficile. La revue initiale a été établie sur les zones où il existe l'éboulement potential. Elles étaient contrôlées à l'aide de la revue topographique et de l'inclinomètre pour que les analyses géotechniques suivantes soient plus sûres et adaptées aux conditions du sol. Les analyses de la construction des murs et des résultats du contrôle ont montré que la planification du mur réteneur était correspondante. Der Autobahneingang in den Trojane Tunnel war projektiert auf Basis von der Kenntnis der geologischen und hydrogeologischen Bedingungen in dem Portalgebiet. Das Gebiet besteht aus dem Tonstein und dem Sandstein. Die Schichten sind tektonisch verformt und sind deswegen sehr heterogen. Die anfaenglichen Untersuchungen haben die Zonen von den potentiellen Bruechen definiert. Weitere geotechnische Analysen waren fitted an reale geologische Bedingungen durch das Monitoring der potentiellen Bruchzonen, welches aus den topographyschen Messungen und Inklinometerdaten entstand. Die Analyse des Wandbaues und die Resultate von dem Monitoring haben erwiesen, dass die Wandprojektierung entsprechend war.

Jan 1, 2003

By R. V. Peche

Since 1952, Bond’s equation has been used as a standard to predict the specific energy of grinding for a given duty. The Bond’s equation considers that the exponent is constant for all conditions. Hukki, in 1961, pointed out that the exponent is a function of the particle size, and concluded that the Bond’s equation applies successfully for an intermediate range of sizes; out of this range the Bond’s equation leads to high error as demonstrated in this paper. More recently, in 2004, S. Morrell presented a new formula in which the exponents vary with the feed and product size. This paper is based on Hukki’s approach and presents a new general formula, in which the exponent varies only with the feed particle size. This new equation has been proven in 82 observable cases in Peru and other countries around the world, involving ball mills and vertimills in different configurations over a wide range of feed and product sizes, work indices and mill diameters; in most cases, the predicted value has an error less than 10% with regards to the observed value and no need for any correction factor. Keywords: Grinding, specific energy, particle size, work index, variable exponent

Jan 1, 2020

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African coal discards derived from feed coal for thermoprocesses pose human health and environmental problems and incur high disposal costs. These issues need to be resolved. Coal fines and a coal fines/ K2CO3 blend were combusted at 700°C in a laboratory rotary kiln to produce ashes containing metakaolinite (Al2O3.2SiO2) and illite/muscovite/orthoclase amorphous materials. The blend ash and coal fines ash, containing 18% K2O and <1% K2O respectively, were leached with water and with 1 M and 8 M NaOH at 80°C for 4 hours using a solid to liquid ratio of 1:5. The 8 M NaOH leach yielded 17% sodalite (Na8Si6Al6O24(OH)2) formation through SiO32-, Al(OH)4-, and Na+ precipitation in the leached ashes. The 1 M NaOH leach yielded no sodalite. X-ray fluorescence analysis of the original ashes and leached ashes showed low Al and Si dissolution efficiencies due to the sodalite formation. Sequential NaOH leaching resulted in the highest potassium dissolution efficiency of 89% for the ashes of fines/K2CO3 blend and 59% for the fines. It may be possible to increase the ash-derived zeolite concentration by using even higher NaOH concentrations (12–20 M NaOH) during leaching. Sodalite derived from coal ash could possibly be utilized for water purification in industrial applications, or as molecule separators. The potassium-containing liquid could be used in fertilizer manufacture.

Mar 30, 2023

By O. Dahl, B. Musuku, N. Schreithofer

Recovery of fine pentlandite is proving to be a challenging task in the Kevitsa sequential flotation operations, with over 60% of the nickel losses reporting into the -25μm size fraction. Since commissioning, the Kevitsa process has undergone major changes to address throughput and flotation performance. Major changes were implemented in the configuration of the milling and flotation circuits as well as in the operating conditions and reagent regime. Some of these changes improved nickel flotation while others deteriorated flotation performance. Most of the changes have had a direct impact on nickel flotation. This paper reviews the systematic analysis, laboratory testing and salient changes done to the process with special focus on the impact on the fine pentlandite flotation. Keywords: Blending, Flotation, Chalcopyrite, Pentlandite, Fines

Jan 1, 2020

By J. H. E. Perry, V. H. Wiik

"The ore deposits of the Zambian Copperbelt occur in sedimentary strata that have been subjected to relatively mild, flexure-type folding. Unrolling serves to reconstruct the original depositional geometry of the folded sedimentary strata and is in common usage on the Copperbelt both for geological analysis of drill hole data and in routine ore reserve estimation.A computerized method of unrolling was introduced at Roan Consolidated Mines in 1969 based on a standard contouring program. A contour map of the geological structure is drawn from a regular grid of elevations, interpolated from the original, irregularly-spaced intersections. Unrolling is performed across this grid, perpendicular to one or two axes specified by the geologist. Each intersection is unrolled independently, and the new co-ordinates are subsequently processed to produce unrolled maps.The technique has been used successfully at RCM over the last two years in both the estimation of ore reserves and exploration planning."

Jan 1, 2014

By K. Duffy, W. Valery, L. Pyle, P. Holtham

A conceptual scoping study was conducted to investigate pre-concentration options for upgrading ore from an Ag-Pb-Zn deposit. The low grade of the ore would result in only modest economic returns, given current market conditions. Several pre-concentration options were considered. These included: selective mining, crushing and pre-screening (following either standard or high intensity selective blasting), bulk ore sorting, particle sorting, jigging, dense medium separation, or combinations of these approaches. Flowsheets were developed for each option, and the upgrade performance was modelled using Limn to determine mass balances and stream tables. Due to the limited availability of test work data, the models were based not only on what test data was available but also on case study data found in the literature. The Bazin technique was used to derive assay by size data for different streams following crushing. Equipment lists and preliminary layouts were established based on the stream tables, and capital and operating costs were estimated for each flowsheet. This information was used to carry out a preliminary economic evaluation using net present value and sensitivity analysis. In this case, the most economically attractive process was found to be particle sorting; although further benefits may be realised by combining with bulk sorting. This paper describes the methodology used and the key findings of the study. Keywords: Pre-concentration, pre-screening, ore sorting, jigging, Ag-Pb-Zn, particle sorting, bulk ore sorting

Jan 1, 2020

By R. A. Wildenboer, R. F. Sandenbergh

Rare earth elements (REE) are present at concentrations of approximately 0.36 % in phosphogypsum stacks located in Phalaborwa, South Africa. The REE are present in the phosphogypsum in solid solution in the gypsum and as fluorine and aluminium rich precipitates. Recovery of the REE offers opportunities for valorization and reducing the environmental impact of the phosphogypsum waste. This paper presents the results of investigations into the leaching behaviour of rare earth elements and other impurities from phosphogypsum using aqueous sulfuric acid. The effects of acid concentration, temperature, residence time, and the influence of impurities were evaluated for their impact on the solubility of rare earth elements in a sulfate medium. It was found that a significant fraction of the REE can be leached from the phosphogypsum in a range of conditions much less severe than traditional hard rock rare earth processing conditions. The REE were leached at a sulfuric acid concentration of 110 g/l, temperature of 30°C – 40°C and a residence time of approximately 8 hours.

Nov 6, 2024

By J. N. Van der Merwe

The current state of the South African mining industry is briefly reviewed from the point of view of an engineer not schooled in the finer details of predictive economics. Based on the assumption that current world exploration targets are indicative of which commodities the world will want in the future, it is concluded that the South African mining industry will continue to be viable and growing well into the future. South Africa holds the minerals the world wants and needs, and as long as the world has people, the demand for those, including gold, will continue to grow. There still is a growing demand for vanity commodities&apos; and even the demand for platinum as a jewellery material displays significant growth. Mine safety still needs to improve, but significant improvement has already been made although the industry is not always acknowledged for the effort in this field. The safety target set for 2013 is within reach but will require sustained effort. The physical mining conditions for the main revenue earners, coal, platinum, and gold, will change substantially in the near future. Research in mining has declined alarmingly and it is urgently necessary for that to be revitalized to generate the knowledge that will be required. In order to streamline the transfer of knowledge to the mining engineers of the future, research needs to be conducted with the full involvement of the universities. It will also be necessary for the universities to continually review curricula to incorporate the latest knowledge and to embark on a campaign of knowledge transfer to the older generation of mining engineers. The mining industry is well supported by the universities, who have done their duty with regard to societal transformation, and the universities are in turn supported by the industry through vehicles like the METE Industry is also strongly supported by a number of professional and vocational societies. The SAIMM will continue to play its vital role as the meeting point of the mining technical sciences, and will continue to disseminate knowledge via the journal, schools, and conferences. In the future, it will review its modus operandi to support the needs of growing membership in the remote branches. It will enter the research arena in an appropriate manner and give effect to the developing integration of mining and society. The most important threat to the future of the mining industry is the recurrent mention of nationalization. While interaction between the mining industry and political and economic development of South Africa has always been characteristic, the current debate is emotional more than rational, and engineers are not well equipped to participate. This matter needs to be finalized before it becomes a popular force that politicians cannot control.

Jan 1, 2011

By W. Robert, J. Wirth, G. Grasselli

ABSTRACT: Strength, deformability and fluid flow properties of rock joints are to a great extent controlled by the surface roughness. The hydraulic conductivity of a rock fracture depends on the aperture distribution, the surface roughness and the contact area, each of which depend on the stresses that act on the fracture plane. However, despite much recent work, a complete understanding of the relationship between void space geometry, contact areas, applied stress, and hydraulic conductivity has yet to be achieved. Moreover, although in situ rock joints are subjected to both normal and shear loading, few studies have been conducted to investigate the effect of shear displacements on fluid flow through a single rock fracture, and which have addressed the issue of flow anisotropy induced by shearing. Experimental flow tests show that with increasing shear displacement, the fracture becomes heterogeneous and anisotropic, and becomes more permeable in the direction parallel to the displacement (Yeo et al., 1998). On the other hand, dry shear tests show that the surface fails in areas facing the shear direction (Grasselli and Egger, 2003). Moreover, the experimental results confirm that the shear strength of rock joints is direction-dependent. In this paper, a three-dimensional morphological description of several a natural fractures that have undergone shear displacement were generated using the Automated Topographic System at the University of Basel. The data analysis method of Grasselli (Grasselli et al., 2002a) is used to determine the surface parameters that are known to control the shear strength. Simulations of fluid flow through this fracture, in various directions relative to the direction of shear, are conducted using an FEM flow simulator. The results constitute the most detailed analysis yet undertaken of the relationship between shear displacement, shear strength, and fracture transmissivity. RESUME: La rugosité des joints en roche joue un rôle primaire sur la réponse hydromécanique du massif fracturé. En effet, la conductivité hydraulique des discontinuités en roche est influencée par la rugosité, et par la distribution des ouvertures et des zones de contact, dont chacun dépend de l’effort normal et du cisaillement qui agissent sur la surface du joint. Les essais d&apos;écoulement en laboratoire montrent que si cisaillée, la fracture devient anisotrope, et plus perméable dans la direction parallèle au déplacement (Yeo et al., 1998). D&apos;autre part, les essais de cisaillement indiquent que seules les zones de la surface qui font face à la direction de cisaillement sont impliquées dans le cisaillement (Grasselli et Egger, 2003). D&apos;ailleurs, les résultats expérimentaux confirment que la résistance au cisaillement des joints de roche est dépendante de la direction. Dans cet article, plusieurs fractures en roche ont été analysées en utilisant un système de mesure topographique à l&apos;Université de Bâle. La méthode d&apos;analyse de données proposée par Grasselli (Grasselli et al., 2002a) a été employée pour calculer les paramètres de la surface qui déterminent la résistance au cisaillement. Plusieurs simulations du coulage, dans diverses directions relativement à la direction du cisaillement, ont été faites à l’aide d’un programme de calcul à éléments finis. Les résultats constituent une des analyses les plus détaillé sur le rapport entre le déplacement pendant le cisaillement, la résistance au cisaillement, et la transmissivité spécifique de la fracture. ZUSAMMENFASSUMG: Die Festigkeit, Verformbarkeit und Hydromechanik von geklüftetem Fels wird hauptsächlich von der Oberflächenrauhigkeit der Bruchflächen bestimmt. Die hydraulische Leitfähigkeit einer Kluft hängt von der Verteilung der Rissbreiten, der Oberflächenrauhigkeit und den Kontaktflächen ab, die ihrerseits von dem auf die Bruchfläche wirkenden Druck beeinflusst werden. Obgleich in letzter Zeit viel in dieser Richtung geforscht wurde, kann der Zusammenhang zwischen Porenraumgeometrie, Kontaktflächen, wirkendem Druck und hydraulischer Leitfähigkeit noch nicht vollständig erklärt werden. Obwohl Klüfte in situ sowohl Normal- als auch Schubspannungen ausgesetzt sind, wurde der Einfluss von Scherverschiebungen auf den Kluftwasserfluss und die daraus resultierende Fliessanisotropie in einer einzelnen Kluft bisher kaum untersucht. Experimentelle Untersuchungen des Durchflusses zeigen, dass die Kluft für größer werdende Scherverschiebungen heterogen und anisotrop wird wobei die Permeabilität parallel zur Verschiebungsrichtung ansteigt (Yeo et al., 1998). Andererseits zeigen trockene Scherversuche, dass die Oberfläche an Stellen versagt, die gegen die Verschiebungsrichtung anstehen (Grasselli und Egger, 2003). Des weiteren bestätigen die experimentellen Ergebnisse eine Richtungsabhängigkeit der Kluftscherfestigkeit. In diesem Artikel wird eine dreidimensionale morphologische Beschreibung mehrerer natürlicher, durch Scherspannungen verschobener Klüfte vorgestellt, die vom Automated Topographic System der Universität von Basel erstellt wurde. Das von Grasselli (Grasselli et al., 2002a) entwickelte Datenanalyseverfahren wird zur Feststellung der die Scherfestigkeit bestimmenden Oberflächenparameter herangezogen. Mittels einer FEM-Simulation wird der Durchfluss durch eine solche Kluft in verschiedenen Richtungen simuliert. Die Ergebnisse stellen die bisher ausführlichste Analyse des Zusammenhangs zwischen Scherverschiebung, Scherfestigkeit und Durchlässigkeit (Transmissivität) einer Kluft dar.

Jan 1, 2003

By F. Dinter, S. A. C. Hockaday, Q. G. Reynolds

The thermal decomposition of carbonate minerals as pre-treatment before smelting reduces the energy requirement for smelting. It can also make the combustion of fossil fuels for heating unnecassary. Thermal decomposition may become important in reducing greenhouse gas emissions when producing ferromanganese alloys while simultaneously reducing electrical energy demand during smelting. A kinetic reaction rate model for the thermal decomposition of manganese ores is presented, based on published reaction rate kinetics for the decomposition of manganese oxides and calcium carbonate. The model was validated against thermogravimetric data for two carbonaceous manganese ore samples and one ferruginous manganese ore sample. The reaction rate model shows that carbonate minerals in the manganese ores are decomposed at temperatures above 900 °C while pyrolusite is decomposed at temperatures from 450 °C to 500 °C. Mn2O3 decomposes rapidly at 550 °C. Braunite decomposition at temperatures below 1000 °C was negligible. The presence of organic carbon in the samples led to further reduction of the samples during thermal treatment.

Aug 3, 2023

By A. Lebedev

Application of dynamic simulation for a base metal processing plant is discussed. The plant receives ore of variable quality from two pits and blending had to be applied to maximise recovery. The plant employs multiple stage crushing, screening, dense media separation, two-stage milling, flotation and further filtration. Stockpiles and bunkers are used in the plant to cater for breakdowns and operating delays, the latter being appropriately incorporated in the model. A detail dynamic simulation model was constructed from the rock face to the filtration plant to assist the plant design, notably with definition of the ore blending method, sizing storage capacity and in-plant conveyors. The plant model was broken down to capital equipment items and various feed types and mass balances were tested to ensure that the production target is met. The dynamic simulation tested the proposed blending method, identified bottlenecks, produced risk profiles for all strategic storage facilities and overall helped minimise the project risks and improve confidence in the plant design. Keywords: Dynamic simulation, ore grade, blending, capacity, risk profile, throughput, utilisation

Jan 1, 2020